Search Documents

By Lars Osen

This investigation was undertaken to contribute to the understanding of underground pull tests by conducting laboratory tests under closely controlled conditions. Steel bolts, instrumented with electrical resistance strain gages, were anchored in an aluminum block, a granite block, and a steel sleeve, and were subjected to pull tests. The bearing plates used were either flat7 dished, or embossed. In pull testing a bolt that is prestressed, there is a range of loading during which bolt load is greater than the jack-applied load, This study showed that preload, the size, shape, and type of bearing plate; and the geometry of the system determine the point at which bolt load and applied load become equal. The effects on bolt load of both a theoretical solution and actual pull tests were analogous and led to similar results.

Jan 1, 1965

By M. J. Pazuchanics

This U.S. Bureau of Mines report presents results from an ongoing investigation of the use of adaptive signal discriminating methods to distinguish between cutting coal and cutting mine rock. Bit-cutting forces and tool vibration were measured in the laboratory as a linear-cutting apparatus (LCA) made constant-depth cuts in coal, sandstone, and shale test specimens. A portion of the collected data has been analyzed and some preliminary results are given here. The influence of data bandwidth, data window size, number of signal features, and voting among classifiers on classification performance are noted. Results to date, based on ideal-cutting conditions and simple geologic materials, indicate that of the four classifiers tested there appears to be no single best classifier. Usually, classification accuracy showed slight improvement as the number of features considered for classification increased. The highest classification accuracies were achieved when voting was conducted among classifiers followed by voting among force components.

Jan 1, 1991

By E. J. Gleim

To make a thorough survey of a coal mine in order to eliminate hazards, the competent safety engineer must be familiar with mere than one branch of engineering. It is essential that he know the properties of mine gases and the methods of detecting them, as well as hew to prevent dangerous as accumulations. It is also essential that he understand the action of overlying strata when the coal is removed, and the proper methods of protection by timbering or other suitable means of support. He must know the value of protective clothing in reducing injuries and mast be informed as to the correct handling and use of explosives to avoid premature blasts, misfires, and ether failures in blasting practice. He must understand hew to operate locomotives and cutting, loading, and various other types of machines to be able to recommend effective safeguards for protecting the men who use them in addition to being informed as 'to these and many ether activities connected with the mining of coal, he must net overlook electrical engineering if he wishes to combat the fire, shook, and ignition hazards attendant upon the use of electrical machinery and circuits in and around the mine intelligently. There are many points relating to safely in the selection, maintenance, and use of electrical circuits and equipment that are perfectly obvious to the electrical engineer but perhaps are not se evident to those not trained in this particular branch of engineering. Engineers of the U.S. Bureau of Mines who have made a special laboratory study of electricity as related to safety in minus haw e also made inspections of electrical installations at a large number of bituminous mines. These inspections have revealed practices and conditions that not only do not contribute to safety but that add nothing to efficiency and economy in the operation of the mine.

Jan 1, 1936

By Raymond M. Stateham

Climatic conditions are compared with roof fall occurrence from April 1, 1972, to December 31, 1975, by the Bureau of Mines. These comparisons indicate that humidity has a strong influence on roof fall occurrence rates. Cubic regression techniques are used to develop best fit curves. Statistical analysis of these curves indicate that both are sinusoidal and exhibit positive correlation with each other. The sine waves have a period of 1 year with maximum and minimum inflection points in August and February.

Jan 1, 1978

The performance of two large-capacity ventilation systems was compared through tests conducted in a large dead-end heading at a pilot oil shale mine in Colorado. Sulfur hexafluoride (SF6) tracer gas was used to measure the performance of the two systems: a free-standing jet fan and a reversible fan with rigid duct. The tracer gas was used to simulate the production of mine air pollut-ants, including blasting pollutants, hot diesel emissions, free methane from surrounding strata, and methane desorbing from muck piles. The test room was 55 ft wide, 30 ft high, and 320 ft long. The performance of the two fans was similar, but the jet fan used less power. The tests showed that either system could provide effective ventilation during oil shale mining.

Jan 1, 1986

By M. B. Cooke, A. D. Bauer, E. W. Dean

The Bureau of Mines is collecting and analyzing representative samples of crude petroleum from all the producing fields in the United States , and the results are being published in a series of reports that are preliminary to the issue of a bulletin covering the entire survey . The bureau has recently completed a survey of crude oils from the Kansas district . In all 27 samples were collected and analyzed , under the direction of A. W. Ambrose , chief petroleum technologist of the Bureau. Valuable assistance was received through the cooperation of oil companies operating in the State , especially the Prairie Pipe Line Co. , and the Empire Pipe Line Co. The present report issued as Serial 2322 , on the Kansas crudes , forms the fifth of the series . Of the four previous papers , the first ( No. 2202 ) deals with crudes from the Eastern fields of the United States , the second ( No. 2235 ) with crudes from the Rocky Mountain district , the third ( No. 2290) gives additional data , cn viscosities and pour tests , for the crudes from these two fields , and the fourth ( No. 2293 ) covers the fields of northern Texas , northern Louisiana , and Arkansas . The details of the methods of collecting samples , making laboratory tests and interpreting results , have been discussed in these earlier reports . It has also been pointed out that the only adequate method of interpreting analyses of crude oils is to compare the individual reports with the analysis of some crude oil that is familiar to the operator . For this reason , no comprehensive discussion of the results of the Kansas survey is attempted, although some general statements may be made .

Feb 1, 1922

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Russell R. Trengove

Core samples from an ore horizon 2,000 feet below the surface were successfully obtained by rotary drilling at the property of the Eureka Corp., Eureka, Nev. The ore was soft and friable; cores were not obtained previously with diamond drills. Whipstocking was used to get samples in a zone 200 feet from a vertical hole. A technique in shipstocking, by which the direction and deviation of the holes were controlled by means of nonfriction-type survey instruments, was successfully employed.

Jan 1, 1956

By Clyde L. Brown

Recent developments in portable communication equipment for use in emergency recovery work following mine fires and explosions have wade possible a convenient and dependable means of directing rescue teams working under hazardous conditions. INTRODUCTION Mine rescue and recovery operations following; fires and explosions are frequently conducted under adverse conditions that require the use of oxygen breathing apparatus by members of a 5- or 6-man team. Conventional apparatus used for this purpose for many years was equipped with an oxygen supply adequate for at least 2 hours. The design of the apparatus is such that the nose passages are closed with a clamp, and breathing is accomplished through a mouthpiece connected to the apparatus by tubes and arranged to prevent inhaling air or gases from outside sources. The use of the mouthpiece has presented difficulties in the development of telephone communication because of the wearer's inability to speak while wearing the mouthpiece. The method of conducting operations of rescue teams requires a person to direct operations at a fresh-air base as close to the rescue team as possible. At least one standby rescue team and 2 or 3 other persons assigned to various tasks are stationed at the fresh-air base. An efficient and reliable means of communication between the director of operations and the rescue team is necessary for reasonably safe and efficient work in hazardous areas.

Jan 1, 1957

By B. K. Cantrell, K. L. Rubow

"Quantifying exposure to diesel exhaust aerosol in an underground coal mine depends on the ability to measure this component of respirable mine aerosol separately from coal dust. Such measurement is complicated by the carbonaceous nature of both the diesel and coal dust particulate that make up the respirable aerosol. Hence, special sampling and analytical techniques must be used to distinguish between these two aerosol components.As part of a continuing study of diesel exhaust aerosol characteristics, the U.S. Bureau of Mines has applied size selective sampling together with gravimetric analysis to separate and measure respirable diesel exhaust and coal dust aerosol concentrations in diesel-equipped underground coal mines. This technique is based on the premise that the diesel portion of the aerosol is predominantly submicrometer and the mineral dust portion is mostly greater than 1 µm in size. In the study, chemical mass balance (CMB) modeling, based on the distribution of chemical elements in aerosol and aerosol source material samples, is used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.Based on the results of the study, the Bureau, in cooperation with the University of Minnesota and the U.S. Mine Safety and Health Administration (MSHA), have developed a prototype personal diesel exhaust aerosol sampler for underground coal mines. The sampler has three stages: a preclassifier stage to select for respirable aerosol, an inertial impaction stage with an aerodynamic diameter(d) size cut at 0.8 µm to separate diesel aerosol from mineral dust and collect the mineral dust, and a final filtration stage to collect the diesel fraction of the sample. The sampler has been evaluated in both laboratory and field experiments conducted by the Bureau, MSHA, and the Generic Minerals Technology Center for Respirable Dust (GMTC-RD)."

Mar 1, 1992

By L. B. Berger

"INTRODUCTION Accurate determination of carbon monoxide in concentrations ranging from 0.2 to about 0.5 percent by volume is troublesome, because such concentrations are too high for some analytical methods and too low for others. Methods that are sensitive to concentrations of carbon monoxide considerably less than 0.2 percent are approaching their upper limit of usefulness when applied to the analysis of samples containing 0.2 percent or more of carbon monoxide, and it may be necessary to resort to dilution of the sample with a known proportion of air, or otherwise modifying the analytical technique, to obtain satisfactory results. Such methods include the determination of carbon monoxide by reduction of heated iodine pentoxide 3/4/5/ by the ""Pyrotannic acid"" method 6/ and by the so-called ""phosphomolybdic acid"" method. 7/ The use of conventional gas-analysis equipment, such as the Orsat type, in the determination of carbon monoxide in concentrations ranging from 0.2 to 0.5 percent is not desirable, as possible analytical errors may be of about the same magnitude, thus producing results of little quantitative value.For several years prior to this publication, the Gas Analysis Laboratory of the Health Division of the Bureau of Mines has used a modification of the Haldane type 8/9/10/ gas-analysis apparatus for the determination, by absorption in a chemical reagent, of carbon monoxide in low concentrations that are not readily determined by other methods. The method is applicable also to the determination of higher concentrations. As the procedure has proved successful and has been adopted by others, this report was prepared to describe the method and to present results of analyses obtained with it."

Nov 1, 1947

By Duvall Wilbur I.

This is the second report to be presented on th application of stress analysis to underground Mining problems. In part I2/ of this investigation the stress distribution around single openings in unidirectional and hydrostatic stress fields was analyzed. Relationships between maximum stress concentration and size and shape of openings were determined by the photoelastic method. In most cases the results were verified by mathematical methods This report considers the stress distribution in pillars formed by two or more openings in a. unidirectional stress field. Relationships between stress concentrations and size and shape of pillars are developed. Applied to mining, results snow how estimates may be made of the stress distribution in pillars, what factors cause high local stresses, and how local stress concentrations may be reduced by proper design of mine openings. The photoelastic method was used, as in Part I, to study the stress distributions, and, whenever possible, the results were verified mathematically. A description of the photoelastic method and equipment is .given in Part I.

Jan 1, 1948

By Charles H. Atkinson, Robert T. Johansen

Tremendous volumes of petroleum ( crude oil and natural gas ) at present cannot be recovered economically . The feasibility of using nuclear explosions for production stimulation therefore has been investigated . Data from underground nuclear tests conducted by the Atomic Energy Commission were reviewed , and the physical effects were evaluated for stimulating petroleum production . Calculations of the effect on ultimate recovery of increasing reservoir temperature with nuclear explosives showed disappointingly small increases . Production increases caused by fracturing of massive low- permeability reservoirs appear technically and economically promising . Petroleum reservoirs that might be converted from submarginal to commercial production are being located and evaluated as to potential reserves and as a location for a field test .

Jan 1, 1964

By L. J. Kane

Several processes being developed by the Federal Bureau of Mines to provide new and more efficient uses for coal require practical methods for removing dust from hot gases. Filters provide such means. The efficiency of filters made of aluminum silicate fibers and porous stainless steel was determined. The results obtained with the fibers were previously reported.5 In this investigation tests were made with three porosities of stainless steel filter material (grades C, D, and E) at a gas flow of 1,000 std. c.f.h./sq. ft. of filter, temperatures of 75° and 1,000° F., and dust loadings (as represented by cumulative dust fed) of 100, 1,000, and 10,000 gr./sq. ft. of filter. Pressure drop during the runs ranged from 0.1 to 21 in. of mercury, and dust removal from 25 to 99.93 pct. Filters having the finest pores gave the greatest pressure drop and percentage of dust removal; however, their dust-holding capacity was slightly lower. Usually, their ability to remove a higher percentage of dust at the same pressure drop more than compensated for the slightly lower dust-holding capacity. With increase in temperature, for the same weight rate of flow of gas, the pressure drop increased and the percentage of dust removal decreased. The effect of temperature was probably due to the accompanying change in the linear velocity and viscosity of the gas.

Jan 1, 1961

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso- and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, 02, N2, H2, and H2; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

By Charles P. Lazzara, Charles D. Litton, Frank J. Perzak

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 1991

By Richard V. Ageton

Compressed- air blowers are frequently used both in large and small metal ines , not only as an aid to ventilation , but in some mines as a substitute for an dequate ventilation system . As a temporary fixture , blowers have their uses , but hey should never be used in lieu of a permanent ventilation system. A number Probably the most common error made in placing dependence on compressed- air lowers as an aid to underground ventilation is the tendency to over- rate their cooling efficiency . It is a very common but natural error to assume that compressed air which issues freely from a blower is of the same temperature as the compressed air which issues freely from the exhaust port of a rock-drilling machine . of readings were taken in different mines of the temperature of the rock- drill exhaust , of the compressed air flowing from the blowers , and of the surrounding air In both cases . In general , the temperature of the rock- drill exhaust was from 10 to 30 degrees below that of the surrounding air , in many instances being slightly below freezing , 32° F . The average temperature for a number of compressed-air lowers and for the mine air surrounding them is shown in Table I.

Jan 1, 1922

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By A. Wahab Khair, S. Jung

"This paper deals with the fracturing process of laterally confined blocks of coal subjected to impact indentation. During the test, blocks of coal with approximate dimensions of 10 in. x 10 in. x 6 in. were laterally confined to predetermined equivalent in-situ stresses and then subjected to an impact indentation by dropping coal cutting bits (various shapes) attached to a known weight from a known height. During the test a number of parameters, namely surface strains (using strain gages), penetration depth (using L.V.D.T.) and acoustic emission characteristics were measured. After the test, the fractured surfaces were photographed with the aid of a camera attached to a microscope. The fracture, its intensity and extended zone within the coal blocks were mapped using sonic techniques. By correlating measured parameters, fractured zones under a given set of test parameters were identified and characterized.INTRODUCTION To improve the understanding of basic failure mechanisms in coal cutting, a better knowledge of fracture and crack regions caused by the indentation in coal is needed. This study reports the detailed experimental procedure used in fracture analysis of indentation experiments on coal specimens using the Acoustic Emission (A.E. hereafter) and sonic techniques. The relationship between microcracking and the inelastic deformation of rock was confirmed by a series of experiments in which the A. E. generated by the cracking in the rock specimen were recorded and the number of events were compared to the strain measurement. (Scholz, 1967).According to fracture mechanism theory, crack initiation in brittle materials such as rocks begins from ""flaws"" either pre-existing or induced by the indentation process itself. Rocks are pervaded by natural cracks and pores, from which numerous possibilities for crack initiation arise (Lindquist, Lai and Alm, 1984)."

Jan 1, 1989