Search Documents

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By George H. Schnakenberg

Automation of coal mining activities at the face offers improvements in worker safety, health, and productivity. Introduction of integrated computer-sensor systems to current mining machines will enable these machines to perform some of the most hazardous tasks through supervised teleoperation. The U.S. Bureau of Mines is pursuing the development of the enabling technology necessary to achieve this goal. The research program consists of both basic and applied research, each focused on the fundamental issues of computer and sensor technologies. Short-term research is directed to providing computer-assisted, remote supervisory operation of present underground equipment; the long-term goal is the development of progressively more intelligent mining systems. The research program includes a review of robotic machine and autonomous vehicle technologies and of current mining technology, which provides a base for developing innovative mining methods; research in navigation and guidance technology, emphasizing control of a continuous mining machine; research on coal-rock interface sensing technology for horizon control, and rib thickness control in highwall mining; the development of computer systems and hierarchical architectures for real-time control; and development of expert systems for machine system fault diagnostics and predictive maintenance. This report presents a brief background and the current status for each of these research areas.

Jan 1, 1989

By Valois R. Shea-Albin

An accurate assessment of the vertical stress on a coal seam at depth is important for mine design. Vertical stress calculation techniques presently available either are not sufficiently accurate or cannot handle complex surface topography. Therefore, the U.S. Bureau of Mines developed a computerized method to calculate vertical stress exerted on surfaces at depth that includes the effect of topography. Two input data sets are required: a digital elevation model containing topographic elevations and a coal seam file defining coal seam elevations at depth. Boussinesq's equation then quantifies the vertical stress resulting from topography. The computerized method was tested on a coal seam overlain by a complex topography where a vertical stress map encompassing several square miles was produced. Results show that depth mitigates the affects of surface topography, while the coal seam topography has a direct effect on the vertical stress. In comparison to the computerized method, the direct stress method overestimates stress under hills and underestimates stress under valleys. The largest difference between the two methods occurs under the steepest topographic relief. A limitation of the computerized method is that stresses cannot be accurately determined near an outcrop.

Jan 1, 2010

By Susan Brink

The U.S. Bureau of Mines is investigating the potential of in situ leach mining a variety of Cu, Mn, and Au-Ag ores. Geologic characterization of ore samples from laboratory leaching experiments is conducted both prior to and after leaching to assess the effects of leaching on the chemistry, mineralogy, and texture of the rocks. The identification and chemical compositions of ore, gangue, and reaction products are determined by a combination of techniques such as reflected and transmitted light microscopy, X-ray diffraction, electron diffraction, electron microprobe analysis, and backscattered electron imaging with scanning electron microscopy. The distribution of the desired metal in various mineral phases can be illustrated using elemental X-ray maps. The potential of reactive gangue minerals to rob Cu from leach solutions is investigated with the aid of transmission electron microscopy. Porosity and permeability are measured to determine how effectively the host rock can transmit leach solution. Textural relationships between ore, gangue, secondary reaction products, and fluid channelways are determined by petrographic examination and are documented by optical photomicrographs and secondary electron imaging. Representative sample selection is described, and several epoxy impregnation and sample mounting techniques are discussed.

Jan 1, 1991

By E. D. Gardner

The Bureau of nines, in cooperation with the mining companies of the Southwest, is conducting an investigating to ascertain the safest and most economical explosives to use in metal mines, and to ascertain the best methods of blasting under various conditions. A part of this investigation has been a study of drilling and blasting drift rounds in metal mines. This paper covers one phase of work on drift rounds and discusses the methods of loading the individual holes of the rounds. The blasting tests, on which this paper is based, were made at the Copper queen Branch of the Phelps Dodge Corporation at Bisbee, Arizona.

Jan 1, 1927

By D. Harrington

"The recent discovery and exploitation of petroleum territory have resulted in the enactment of new petroleum laws in most of the South American Republics. The activities in the discovery of these new fields were engendered by the knowledge of the fact that present producing fields must within well defined periods be exhausted. Oil operators were willing to take the initial steps in exploitation in the absence of legislation that applied strictly to petroleum operations. The enactment of modern legislation in many of these Republics encouraging and protecting exploitations may cause tremendous oil activities in these countries, and the results may be comparable with the magnitude of the undertakings and the prestige of the companies now entering this territory.These, oil fields are admirably located for convenient distribution of petroleum by water to all the Nations using oil as fuel for shipping and industrial concerns. The oil markets of the western coast of South America will derive immense benefits from the Panama Canal. This navigation route brings these markets into direct ocean shipment with the Atlantic coasts of the Western and Eastern Hemispheres.One deterrent to oil production in the Republics of South America is the want of inland. transportation facilities, but the recent laws of these Republics without exception provide for acquiring rights of way for pipe lines and other modes of transportation; and doubtless the great interests and. syndicates already operating in these regions will, as production increases, provide ample pipe line transportation sufficient to convey to the coast the oil produced. It way be assumed, from the legal guarantees afforded, and from operating equipment and machinery that are now being concentrated that refineries will be erected at shipping points for the purpose of making these petroleum products accessible to the world."

Jun 1, 1921

By L. H. Johnson

"INTRODUCTION The Pennsylvania anthracite industry produced 53 million net tons of anthracite during 1945. Fifty-one million tons was prepared for the commercial market (3), 3/ and 2 million tons (consisting of fine sizes) was used for colliery power consumption. Of the number of tons prepared for market, 17 million tons (33 1/3 percent) was prepared by the use of acid mine water treated with lime.Mine water from underground workings is pumped, drained, and stored in huge quantities. The mine-drainage systems in the anthracite region handle over 200 billion gallons of water annually, of which 150 billion gallons is pumped to the surface. More than 69 billion gallons of water is impounded in underground pools (1). Much of this water is employed for breaker use, dust-control installations; hydraulic backfilling, combatting mine fires; and aiding in the transportation of anthracite in gently dipping places where sheet iron is used Roos(4) estimates that 1,100 gallons of mine water is utilized in the preparation of anthracite mined."

Nov 1, 1946

By C. L. Brown

Among the more recent developments for breaking coal in mines is the Airdox system, in which high-pressure compressed air is conducted to the points of application by means of heavy-duty steel and copper tubing. Stray electric currents can be detected on y of the compressed-air lines, and evidence of such currents is rev led, by arcs and sparks when contact is made between the tubing and mine track or other equipment forming a current path with the track. Explosive gas is liberated in many coal mines; therefore, from the standpoint of safety, it is desirable to eliminate all possible sources of gas ignition, including stray electric currents. The purpose of this report is to reveal the source, magnitude, and possible methods of controlling stray currents in compressed-air lines that are used in connection with Airdox systems. Stray electric currents have been studied in most coal-mining localities in the United. States where Airdox equipment is used. The information given in this report is based on the find of these studies.

Jan 1, 1949

By H. H. Dewing

The U.S. Bureau of Mines characterized Hg-containing wastes and used a thermal-desorption process to remove and recover the contained Hg. The wastes were generated by an electrical-parts plant engaged in the assembly of Hg-containing switches and contained phenolic resins and paper insulating materials mixed with soil. The average Hg content was 396 ppm. Numerous characterization tests showed the Hg was tightly absorbed and could not be removed or concentrated by leaching or gravity separation techniques. Laboratory retort tests showed the Hg content reduced to < 16 ppm in 2 h at 400 °C; rotary-kiln, thermal-desorption tests required 4 h at 450 °C. Airflow through the retort im¬proved thermal-desorption efficiency, but vacuum operation only slightly reduced the temperature needed for thermal desorption. Offgases from decomposition of organic materials were burned in a high-temperature afterburner and subsequently cooled in a heat exchanger to condense water vapor. Finally, the Hg vapor was condensed and absorbed from the offgas by activated charcoal. Mercury recovery was over 99.99 pct of the desorbed Hg. Thermal-desorption processes have had wide application to many Hg-containing wastes, and historical experience in Hg mining has demonstrated its potential cost effectiveness.

Jan 1, 2010

By Jon C. Volkwein

The Bureau of Mines and many member companies of the Industrial Sand Association have been working in several areas to reduce personal exposure to respirable dust. Areas investigated include ventilation, modification of hardware, moisture addition to the product, and improved housekeeping practices. Ventilation systems have been devised and shown to contain 100 pct of a tracer gas released within the hood. An industrial clean air island has been developed and shown to reduce dust levels 90 pct at the opera- tor&apos;s position, Modification of hardware on a bag filling machine has been demonstrated to reduce dust 83 pct at the machine operator&apos;s lapel. This particular development has been termed a significant advancement in the state-of-the-art of bag filling by industry representatives. Addition of moisture to dried product materials has been tested with results showing dust reductions of 90 pct are possible!, Control of the moisture addition method still needs refinement and costs may be prohibitive. Dust sampling results clearly show the benefits of housekeeping practices such as building cleaning and vacuum sweeping. Rotation of work schedules is also effective for reducing personal exposure.

Jan 1, 1985

By R. A. Cattell

With the activities of the Petroleum and Natural Gas Division geared chiefly to problems directly connected with the war effort , the emphasis of the work under oil and gas development and production was to make engineering studies of selected reservoirs for the Petroleum Administration for War , to determine the extractable quantities of components in them, and to study the characteristics of these components for use in the manufacture of aviation gasoline and other products . The needs of the Petroleum Administration for War and the operators for specific data from gas - condensate fields were fulfilled , and , in addition , engineering data along lines of a forward - looking program of research on reservoir behavior were collected , which should be of great value in the postwar period . It is planned to publish many of these data as soon as conditions permit . The work of the Secondary Recovery Section had as its objectives in- . creasing the rate of production of crude petroleum and , which is more important , preventing the premature abandonment of wells in " stripper " and marginal According to the National Survey of Stripper Wells by the National Stripper Well Association in cooperation with the Interstate Oil Compact Commission , a total of 67,460 stripper wells was abandoned from January 1 , 1935 , to July 1 , 1942 , inclusive , with an estimated loss in proved reserves of approximately 216 million barrels . This survey also indicates that over 1.2 billion barrels of oil would be recovered by primary production from more than 290,000 stripper wells then in operation , and an additional 2.5 billion barrels of oil could be recovered from them by secondary production methods . The work of the Chemistry and Refining Section was oriented towards the optimum utilization of crude oils in the manufacture of aviation fuels for spark-ignition and jet - propulsion engines . The work involved intensive studies of superfractionation , hydrocarbon analysis , and the engine testing of fuels . Particular attention was given to the effect of sulfur compounds in the crude oils and in the fuels made from them . The research on thermodynamics is concerned with the experimental determination of precise and accurate values of the fundamental thermodynamic constants of pure hydrocarbons and related compounds . The data obtained in these investigations will be utilized for devising and improving chemical processes in which petroleum hydrocarbons are the raw materials . Without such data , much time and expensive material and equipment may be wasted in attempts to obtain reactions under conditions that the laws of thermodynamics rule out of consideration . Thermodynamic data are useful and required in the petroleum industry for calculations of heat balances in the design of furnaces , fractionating towers , and heat- transfer equipment . It is of utmost importance , also , to know the heat requirements of cracking and other chemical reactions so that heat may be supplied or dissipated in the proper proportions . These needs for thermodynamic data are being recognized more and more by petroleum -refining engineers . The responsibility for the production of helium for the Navy , the Army , other governmental agencies and non-Federal users is vested in the Bureau of Mines by an Act of Congress ( 50 Stat . 885 ; 50 U.S.c. 161-166 ) . The Helium Subdivision of the Petroleum and Natural Gas Division continued to meet all demands for helium .

Jun 1, 1949

"When a metal-mining company takes out a workmen's compensation insurance policy, it does so to relieve itself of its uncertain and variable financial liability under laps requiring payment to employees for lost-time accidents, there-by passing the liability or to the insuring agency. For this service, or rather for the assumption of the risk, the insuring agency charges the mining company a price, or in insurance parlance, ""a premium"".The insuring agency depends upon a volume and variety of business to average the losses incurred by its individual policy holders, and determines its price to cover losses that are suffered and its cost of doing business.It is generally known that all types of insurance are founded on the theory of probability applied to large groups of risks, Workmen's compensation insurance is no exception, and the average price paid therefor must be based on the frequency and severity of accidents in the particular industry or branch of industry under consideration. The frequency and severity rates are determined by statistics, which, of course, unless standardized, kept carefully and consistently, and analyzed properly, are liable to be inaccurate and misleadingThe importance of large groups in arriving at an average price for insurance service can not be overestimated, For example the writer knows of one small group of some twenty metal-mining companies whose losses during the past two years exceeded their premium charge by 54%. Not a single individual company during the two years kept its losses below the premium rate. For several years the group as a whole has persistently exceeded its premium rate, Such risks are not profitable to the insuring agencies and can only be carried where a large volume of good risks will balance the poor risks, but in order to conform to good insurance ethics the premium rate must be based on averages for the industry as a whole, and kept sufficiently low to induce operators to sell their risks."

May 1, 1924

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation&apos;s mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By J. H. East, D. Harrington

Fires in metal mines have resulted in some of the worst disasters in American mining history insofar as loss of life is concerned. One fire caused the death of 163 miners and individual less spectacular fires have cost the lives of scores of workers. Metal mines are often very deep, and the men working on numerous levels far removed from direct communication with the surface. In many instances they cannot be warned quickly of an emergency or a mine fire by telephone or other usual method of communication, or by messenger, flashing lights, gongs, sirens, or whistles. Telephones are not paricularly effective as a means of warning unless placed at all strategic points and with attendants always on duty; though telephones well placed have a definite value in any well-pla.mied emergency procedure in mines of all kinds. Messengers are slow and men working in remote parts of a mine would not receive a warning quickly enough. Most metal mines are not electrically lighted, except at or adjacent to shaft stations and in principal haulageways, and this limits the effectiveness of flashing lights. Electric gongs and sirens or whistles have been tried as warning signals, but the sound is quickly deadened and does not travel upward into the stopes, especially those of an extensive volume. Shutting off the compressed air is by no means satisfactory as a warning, as not infrequently it is stopped accidently, so that it loses its value as an alarm. The introduction of water into compressed air lines is undesirable as a fire warning and necessitates considerable care, especially in deep mines; pressure-reducing valves must be provided to reduce pressure that otherwise would break connections or split the pipe. A quick, effective method of warning miners underground of the existence of an emergency requiring them to leave the mine immediately, such as a fire on the surface or underground, is provided by the introduction of stenches in the compressed-air lines. This method of warning is by no means experimental, inasmuch as it has been used successfully for many years in

Jul 1, 1943

By John R. Bartels

Jan 1, 2009

By H. B. Brunot, L. C. IlsLey

The chief object of the Electrical Section of the United States Bureau of Mines is the study of causes and means of preventing accidents resulting from the use of electricity in mines . A large part of this work for the last 20 years has been the inspection and testing of mining equipment under the provisions of schedules which give the minimum requirements considered essential for the safety of equipment intended for use at or near the working faces of dusty or gassy mines . During the first few years of this work , particular attention was paid to the explosionproof features of the various accessories such as motors , controllers , and other parts . The knowledge of the essentials necessary for safe designs of enclosures has since been augmented by field experience and by data obtained in testing a large number and variety of designs . With our present knowledge it would seem that a disproportionate stress was placed on making the various enclosures explosionproof , but not enough thought was given to the danger from wiring and connections outside of explosionproof enclosures . The list of equipment that has met minimum requirements for safety and has been approved as permissible by the Bureau of Mines includes storage - battery locomotives , power trucks , drills , loading machines , conveyors , cutting machines , room hoists , pumps , concrete mixers , and rock-dusting machines . The wiring on some of the machines is comparatively simple and sometimes , except for the trailing cable , may be entirely within the explosionproof enclosures . In general , there is outside wiring between enclosures , and on the larger machines the wiring may be extensive and complicated . In considering the safety of wiring for mining machinery , attention must be given the severe service and unfavorable surroundings imposed by mining conditions . Some of the matters that require consideration are : ground . The lack of care of the exterior wiring to be expected in the average mine . The lack of adequate periodic inspection of the wiring . The absence of adequate facilities for satisfactory inspection and repairs under- The severe conditions of moisture , dirt , mechanical injury , and low voltage encountered in mining service .

Apr 1, 1931

By John F. Wiggert

The first signal system used in the Homestake mine between the cagemen and hoisting engineers was a mechanical one. It consisted of small cables or jointed steel rods hung in the cage compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers&apos; positions by means of bell cranks and steel wires. At the various stations the bell lines were also fitted with bell cranks and connected levers, so that the cagemen could operate the bells from the stations when they were handling rock or other material and not riding on the cages. Such a system was inherited from the days before extensive electrical development. It served quite well for shallow shafts, but for depths of a thousand feet or more it was very slow and cumbersome. It required consider-able muscular effort to operate it quickly, because of the inertis of its great weight and also because of frictional resistance. The maintenance cost was quite high because of the many wearing parts.

Jan 1, 1937

By P. M. Gruzensky

In view of some of the outstanding properties of chromium, considerable effort has been made in recent years to prepare the high-purity metal in ductile form. The object of this investigation was to obtain such metal by electrolysis of chromic acid solutions and to determine the conditions that yield optimum results. The apparatus is described, as well as the parameters that received consideration. Ion-exchange resins were employed to remove cation impurities from the electrolyte. Tensile specimens prepared from the electrodeposits by arc melting, press forging, swaging, and drawing, were ductile at room temperature. INTRODUCTION Metallic chromium displays an exceptionally high resistance to corrosion, oxidation, and wear at elevated temperatures. Although these properties are utilized to some extent when chromium is alloyed with other metals, such as in stainless steels, high-chromium alloys and pure chromium are not employed as engineering materials because of a serious lack of ductility and impact resistance at room temperature. Because high-chromium alloys appear promising as refractory metals for applications such as in gas turbines, much interest has been shown recently in the preparation of uniformly ductile chromium and in determining which factors contribute to its brittleness.

Jan 1, 1957

By James C. Cawley

The Bureau of Mines has empirically determined ignition probability versus current for resistive circuits in an 8.3% methane-air atmosphere. Simple ignition probability, defined as the number of ignitions divided by the total number of sparks, was determined, and the corresponding currents were recorded. The experiment was designed to minimize the probability of not observing an ignition that should occur during a series of tests. For resistive circuits in 8.3% methane-air mixtures, the experimental results indicate that ignition was not achieved below 2,000 rnA at 20 V dc, 350 rnA at 30 V dc, 150 rnA at 40 V dc, and 175 rnA at 50 V dc. The simple probability of ignition corresponding to these currents is esti-mated to be, respectively, 1.0 x 10-6, 1.7 x 10-7, 3.0 x 10-7, and 1.0 x 10-5 The ignition mechanism seems to break down below this point, implying that a threshold current value exists below which spark ignition does not occur.

Jan 1, 1987

By William H. Pomroy

Fires in underground metal and nonmetal mines pose a threat to the safety of underground miners and to the productive capacity of this Nation&apos;s mines. Contaminated air (smoke, carbon monoxide, and other products of combustion) is the primary life safety hazard created by a mine fire. The most reliable defense against the hazard posed by the rapid spread of contaminated air underground is early warning fire detection and rapid evacuation. This Bureau of Mines report describes the design and operation of four prototype early warning fire detection systems, for underground noncoal mines, presently undergoing prolonged in-mine testing by the Bureau. The systems are described within the context of the underground mine environment.

Jan 1, 1985