Search Documents

By D. J. Bauer

This report covers a phase of an extraction project carried out as part of a research program on rare-earth technology. The current project--the production of pure cerium compounds--is an intermediate step between ore processing and metal reduction. In this connection, a study on a separatory-funne1 scale was made on nonreducing extractants for recovering cerium (IV) from tri-n-butyl phosphate (TBP) and of methods for recovering the cerium nitrate from the strip solution. Dilute sulfuric acid was found to be 100 percent effective in stripping cerium (IV). Several precipitants were effective in recovering the cerium from the strip solution, and ethanol was especially promising. A scaled-up investigation was made into the use of spray-tower type equipment to perform the function of extracting, washing, and stripping. This equipment, referred to as the pressure-bubbler, utilized the system developed on the separatory-funnel scale. Feed solutions were prepared from a bastnasite concentrate by two techniques. Of these, the sulfated bastnasite solution was most successful, resulting in 86-percent recovery of the cerium at 99.7+-percent purity.

Jan 1, 1959

By William H. Schiffbauer, Ph. D. Mowrey

Proximity warning devices can improve workplace safety by alerting workers when they are in a hazardous area near moving equipment. Industrial work sites often present extreme challenges to safety-based proximity warning devices. Many commercially available types of proximity warning sensors and systems can be rendered useless when covered with mud, ice, snow, ore, rock, and other material. The list includes radar, ultrasonic, capacitive, and visual types of sensors and systems. Addressing these shortcomings, NIOSH personnel have developed a patented active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) which employs lowfrequency, low-power magnetic fields which are quite impervious to severe environmental conditions. A shapeable wire loop antenna which provides the marker of dangerous work areas, has been mounted on a continuous mining machine and was mounted inside 1.3-cm thick angle iron. This loop antenna was exposed to more than six months of active underground coal production, which included being covered by and scraped over with tons of rock, sprayed by a continuous stream of water, and immersed in thick mud. After six months the loop antenna showed signs of wear, but was still capable of performing its intended function. The HASARD system is now being applied to other industrial applications and is showing much promise, especially in harsh environments. This paper details the system, describes the tests that have been done, and mentions other areas where it can benefit the safety of industrial workers.

By Albert J. Rambosek

The objective was to obtain qualitative information on (1 ) the stress field in a core stub at the bottom, or face , of a cored borehole and (2 ) whether , and at what distance , in terms of core diameters from the face of the borehole , relief of stresses in the core is complete . The photoelastic and brittle lacquer techniques of stress analysis were used to determine the pattern of stresses in two- dimensional models , simulating the bottom of a borehole with a projecting stub of core . The core was stress- free at 1-1 /2 core diameters or more from the face of the simulated borehole . The analyses of the isoclinic and isochromatic patterns in the core near the face of the borehole reveal why core occasionally breaks into thin plates , when core or stress - relief drilling is attempted in highly stressed rock masses , such as heavily loaded mine pillars . stub broke away from the bottom in a hydrostatically loaded artificial rock specimen in a manner indicating that core " wafering" can result from tensile stresses developed in the core when a coring bit penetrates the highly stressed rock mass .

Jan 1, 1964

By G. St. J. Perrott, N. A. Tolch

"PURPOSE OF TESTSThe propulsive strength4 developed by the Cardox blasting device depends on the thickness of disk, weight of heater element, and weight of carbon dioxide charge. It might be supposed that the maximum weight of carbon dioxide that can be charged into the shell should give the greatest strength. However, according to the ballistic pendulum, the maximum weight of carbon dioxide with certain conditions of heater and disk has less propulsive strength than a smaller charge; in one condition of test a loss of 39 per cent in propulsive strength was noted. It is therefore of interest to study the effect of the variables that determine the strength of Cardox.ACKNOWLEDGMENTGrateful acknowledgment is made to A. B. Coates, associate mechanical engineer who developed the testing method for measuring pressures in the Cardox shell.DESCRIPTION OF DEVICEThe Cardox blasting device as fully described by the bureau in Report of Investiga¬tions 2920 (1929), consists essentially of hollow—steel shell, cylindrical in shape, an electrode, valve assembly, shearing disk, and discharge cap. The shell is prepared for use by inserting a heater element, closing the open end with a shearing disk, and screwing in place the discharge cap. The charge of carbon dioxide enters the shell through the electrode.The heater element is fired by an electric igniter of the match—head type. The heat released by the heater element completely gasifies the carbon dioxide and raises the pressure of the gas until it is enough to shear the disk."

Apr 1, 1931

By I. D. Shah

The Bureau of Mines investigated the sequence of principal chemical reactions taking place during the roasting of covellite (CuS). Practically all covellite is converted to digenite (Cul.SS) before oxidation to Cu20 begins. Part of the Cu2O is then converted to CuO, which in turn forms CuS04 through CuO?CuS04 as an intermediary. CuS04 and CuO'CuS04 decompose at 600° to 700° C to yield CuO and S03 (g) as final products. An overall mechanism is proposed for chemical reactions occurring at different interfaces of partially oxidized CuS pellets.

Jan 1, 1970

By G. W. Birge

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Westmoreland County for coking tests was based, in part, on estimates of the coal reserves by Dowd,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in thousands of tons, as follows: [ ]

Jan 1, 1957

By R. H. Nielsen

A new, cheaper precipitation scheme has been developed to produce purified zirconium oxide, Technical-grade sulfuric acid is used to precipitate a basic zirconium sulfate from a hot dilute hydrochloric acid solution. With close control of temperature, pH, and zirconium - sulfate ratio, excellent purification and complete zirconium recovery can be attained. The process has been successfully applied for 3 months and has proved to be a more satisfactory procedure than the ammonium phthalate process used previously. INTRODUCTION The Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines has developed and improved the Kroll process for the production of pure ductile zirconium and hafnium. metal. Since 1946 over 1 million pounds of zirconium sponge metal has been produced, mostly high-purity material for the Atomic Energy Commission

Jan 1, 1956

By Thomas Fraser, J. D. Davis

"INTRODUCTION Preliminary tests of the Oyon coal constituted part of a wartime exploratory and development program in which many agencies participated. The general objective was to find new and adequate source of fuel and other raw materials for greatly expanded industry.The Oyon coal field, known for at least a hundred years to the mining people of Peru, offers a possible source of high-grade process fuel for the growing metallurgical industries of South America and the Pacific coast. Santolalla 4/ reports that low-volatile coal from this region was used in local smelting operations as early as 1850. It has been mined in very small quanti¬ties for many years and used in neighboring mining camps and villages. Small quantities are regularly used at Oroya for the manufacture of carbide, and in recent years small-scale coking operations in specially designed ovens in the region have demonstrated that these coals will make dense coke.During this long period of desultory operations many small openings have been made scattered over a wide area in this general region, indicating very extensive occurrence of the coal measures, although systematic exploration work has not been undertaken. However, current development work of the Banco Minero del Peru has opened up several substantially parallel highly inclined or vertical beds of workable thickness and has followed these deposits to sufficient lateral extent to prove fairly well the existence of substantial reserves on this property."

Mar 1, 1948

By A. B. Coates, J. E. Crawshaw

"The use of such methods and apparatus as the Dautriche method and the Mettegang recorder for the determination of the rate of burning of black blasting powder and other strictly burning explosives has been found to give such erratic results that no reliance can be placed on the data thus obtained. Consequently, investigators of those factors which may affect the burning rate, such as size of grain, absolute density, chemical composition, and means of ignition have had to rely mainly on observations made during practical use for determination of the part played by each. Such tests are very difficult of interpretation.The purpose of this paper is to describe a method used by the explosives division of the Bureau of Mines for the investigation of such explosives and to present the results of an investigation using that method.The investigation was concerned with the effect of grain size, initial pressure, and means of ignition on the rate of burning or rate of pressure development of black blasting powder as compared with pellet powder.The Bichel pressure gauge was used for these tests, with the slight modification to the apparatus and method described in U. S. Bureau of Mines Bulletin 15.4 These modifications consisted of reducing the speed of the revolving drum on which the time-pressure record is taken, measuring the speed of the drum by a belt-driven tachometer, and introducing an induction coil in series with the electric squib or electric detonator to mark on the time pressure record the instant at which the squib or detonator was fired."

May 1, 1929

By R. L. Andrews

The Bureau of Mines investigated means of electrodepositing iridium to form thick coatings suitable for the protection of such metals as tungsten and molybdenum, which oxidize rapidly at high temperatures. Using a fused sodium cyanide bath, thick, adherent, and coherent deposits of iridium up to 15 mils thick were plated on tungsten and molybdenum substrates at 600° C and current densities of 10 to 100 ma/cm2. Limited oxidation testing of molybdenum encapsulated with pure iridium indicates that the coating may offer protection to approximately l,000° C in flowing air, but that at higher temperatures, the volatility of its oxide limits use of pure iridium. Alloy coatings of iridium with platinum, palladium, and rhodium up to 4 mils thick were formed from a fused sodium cyanide electrolyte; because their oxides are less volatile, these alloys may protect substrates at higher temperatures. Deposits made from aqueous electrolytes either had very low rates of deposition or were highly stressed and cracked when heavy deposits were made.

Jan 1, 1967

By J. W. Paul

Mine foremen are employed in coal mines for two reasons: First, so that the underground work. may proceed in an orderly manner and that each employee gives attention to his duties; and second, by reason of the State law which re- quires the employment of such officials to see that the laws relating to safety are carried out. It may be seen that, with these two duties, the foreman has wide scope of authority and much responsibility. As foreman of operations he has to meet certain economic questions that contribute to the cost of producing the coal, and as the agent of the State he must also supervise and coordinate the work in such manner as to insure that the employees work under safe conditions. As the roof of coal mines is the source of the greatest hazard naturally the care of the roof must take much thought and planning on the part of the fore- man; and this circular is therefore presented to call attention to some things he may do to prevent injury to the workmen by falls of the roof material or coal. Mine foremen, in the principal coal-producing States, are certified by a State board which prescribes certain qualifications, experience, and character, attested by examination and personal endorsement. Certified foremen, therefore, are men who have had experience underground and know roof conditions and timber- ing methods. The suggestions herein are based upon observations made at many mines and collectively embrace practices that have been found to be in effect and pro- moted by experienced mine foremen:

Sep 1, 1930

By A. J. Kraemer

"During the past several years a great deal of discussion has centered around the question of the permissible limit of sulphur content in fuels for automotive and aviation motors. Under certain conditions of operation, sulphur in motor fuels causes the formation of corrosive substances which attack bearings, wrist pins, and other parts of engines. On the other hand, in making gasoline from certain stocks, the gasoline fraction normally contains a relatively large proportion of sulphur compounds. By the generally used processes of reducing the sulphur content, a significant part of the gasoline fraction is lost as motor fuel, and added expenses are entailed for chemicals, labor, and other process costs. This condition has been an economic burden to some refiners of high-sulphur crudes. In some instances the treating losses have been rather severe and the treating costs relatively high, but the data presented in this paper indicate that the reduction of sulphur content of motor fuel is a problem to a relatively small number of refiners and of little or no concern to the remainder; in fact, more than 90 per cent of the 153 samples analyzed passed the Federal specification requirement, Which limits the sulphur content to 0.10 per cent. 3This report is based upon the results of an examination for sulphur content, Doctor test, copper strip corrosion, and color of the samples collected during January, 1930, for the twenty-first semiannual gasoline survey of the Bureau of Mines. The results of the gravity ad distillation tests of the survey were published as Report of Investigations 2995. The numbering of the samples given in this report is the same as in Report of Investigations 2995; for example, No. 25 of this report is the same sample as No. 25 of Report of Investigations 2995."

Jun 1, 1930

By J. W. Stevenson

The Bureau of Mines investigated the influence that atmospheric pressure changes exert in a gassy coal mil on a ventilating air current with a system of bleeder entries. During the season when abnormal barometric fluctuations usually occur, recording instruments monitored the air current ventilating an active coal-producing area. It HL he rate of coal production caused a more significant change in methane concentration than did barometric change. The hazard that accompanies methane release due to expansion of the gob gases during atmospheric lows was minimized by the effective bleeder system.

Jan 1, 1966

By R. H. Harrison, D. R. Douslin

The thermodynamic properties H - H° , (H - H° ) /T , S - Sideal , S - S° Fide al F - F° , (F F° ) /T , and activity coefficient Y for perfluorocyclobutane were calculated as functions of temperatures ( 115.22 ° to 350 ° C) and molal density (0.75 to 6.5 moles / liter ) . Improved analytical and graphical correlating techniques are described .

Jan 1, 1964

By Arne Landsberg

Accessory metals, although valuable resources, present possible environmental concern in the smelting of base metals. The Bureau of Mines, U.S. Department of the Interior, has undertaken research to define the chemistry involving these metals. Arsenic in copper smelting is the first to be investigated. Roasting, the first step in many copper smelters, was chosen for initial investigation because of the potential for arsenic removal in this primary process. Simple, static-bed, vaporization experiments were devised to obtain the data in this study. Ancillary transpiration and mass spectrometry were also used to delineate conditions necessary for arsenic volatilization from a roaster feed. For nearly complete arsenic removal, a temperature of 650°-700° C, a reducing atmosphere including carbon monoxide, and a source of sulfur were found to be essential.

Jan 1, 1980

By R. H. Dickson

This paper, which describes the milling practice of the Verde Central Mines, Inc., is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. GENERAL DESCRIPTION The Verde Central concentrator is located in Walnut Gulch, about 1 mile west of Jerome, Ariz., and on the Jerome-Prescott highway. It is about 1,000 feet distant from the main shaft of the Verde Central mine and treats ore from this mine only. The mill is connected with the main shaft of the mine by a 24-inch gave railway, over which the ore is hauled in 5-cubic yard capacity, rocker, side-dump cars, by a 3-ton Brookville gasoline locomotive.

Jan 1, 1931

By B. R. Eichbaum

To develop technology to assure an ample supply of zinc and to reduce environmental pollution, the U.S. Bureau of Mines investigated alternatives to the roast-leach process for treating complex sulfide concentrates. Previous studies proved that low-grade zinc sulfide (ZnS) concentrates could be leached using chlorine-oxygen to produce zinc chloride (ZnCI2). The process involves high energy requirements for evaporating the pregnant solution to produce anhydrous ZnCl2 needed for electrolytic cell feed. An efficient hydrometallurgical process would facilitate treatment of lower grade ores than can be used in conventional processing and would render roasting unnecessary. An alternative method was devised for recovering ZnCl2 from solution. Zinc diammine chloride [Zn(NH3)2CI2] was precipitated from solution by adding ammonium chloride (NH4CI) and sparging with ammonia (NH3) to a pH of 6 to 7.5. The spent solution was treated with calcium hydroxide [Ca(OH)21 at 60° to 80° C for 1 to 4 h to remove remaining zinc and NH3. The Zn(NH3)2CI2 was heated to 300° to 400° C to remove NH3 and produce anhydrous ZnCI2. A possible flowsheet was devised and is included.

Jan 1, 1991

By L. F. Willmott

Pulverized high-volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure-gasification pilot plant equipped for slurry feeding. The minimum ratio of water to pulverized coal that could be pumped satisfactorily as a slurry was about 1 to 1. Heating this slurry produced a suspension of coal in superheated steam having a steam-to-coal ratio greater than the 0.3 to 1 proportion that is considered optimum for pressure gasification of pulverized coal. A steam separator removed enough steam to provide ratios down to about 0.5 to 1, but a 0.3 to 1 ratio was not achieved. Gasification of Sewickley coal produced a synthesis gas containing about 36 percent H2, 46 percent CO, and 13 percent CO2, Gas output, gas composition, and coal and oxygen requirements were Virtually the same as for a pilot plant equipped for fluidized-coal feeding. Typical results from the slurry-fed plant at 300 psig were carbon gasified, 95 percent; coal requirement, 34 lb/M (thousand) std cu ft CO + H2 produced; oxygen requirement, 365 std cu ft/M std cu ft CO + H2 produced. The results showed that the two feeding methods are equally satisfactory from the standpoint of gasification. A choice between a fluidized-coal gasification process or a slurry gasification process depends on considerations relating to the coal-feeding phase itself, including capital and operating costs, manpower requirements, safety, and flexibility of operation.

Jan 1, 1962

By Keith L. Harris

Real gross national product3 (GNP) grew at a seasonally adjusted annual rate of 4.2% in the fourth quarter compared with a revised 4.3% rate in the third quarter, according to the most recent estimates released by the U.S. Department of Commerce (table 1). Expanding inventories, Government purchases of goods and services, residential fixed investment, and a narrowing of the trade deficit fueled the growth. Significantly reduced consumer demand led to the heavy inventory growth. Almost half of the buildup in inventories consisted of automobiles because consumers reduced purchases when Detroit ceased most incentive programs in late summer. Reduced consumer demand also affected imports, however, and the narrowing of the trade deficit resumed after widening in the third quarter. Nonresi- [ ] dential fixed investment also declined after a strong gain in the third quarter. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 2.9%, the same as that of 1986. However, on a fourth-quarter-to-fourth-quarter basis, the real growth reached 3.8%, the highest growth since 19M, and exceeded the Reagan Administration's estimate of 3.4%. Rising merchandise exports accounted for about one-third of the growth in GNP for all of 1987 and are expected to continue to grow as domestic manufactures benefit from the lower value of the dollar vis-a-vis other major trading country currencies. Consumer demand became a less important factor of economic growth, but employment continued to grow (table 2), and civilian unemployment declined by 0.9 percentage points (December to December) as the industrial sector geared up to increase exports. Inflation, as measured by the fixed-weighted GNP price index, remained low at 3.4%.

Jan 1, 1988

By Murray Jacobson

The Federal Coal Mine Health and Safety Act of 1969 established mandatory dust sampling of coal mines according to procedures prescribed in the Mandatory Health Standards, title 30, Code of Federal Regulations, part 70, published in the Federal Register on April 3, 1970. A laboratory was established in the Pittsburgh Field Health Group of the Bureau of Mines to process the coal mine dust samples collected by the mine operators. This paper describes the laboratory and presents the equipment and procedures used in processing these samples.

Jan 1, 1971