Search Documents

By W. G. Messner

Pipelines for transporting crude oil and refined products in the United States totaled 189,982 miles on January 1, 1959. This mileage was less than a 1-percent increase from the 1956 total of 188,540 miles. During the three-year period (January 1956 - January 199), 14,886 miles of new pipe and 10,649 miles of secondhand pipe was laid. Pipe taken up in the same period was 24,093 miles. The facts regarding pipeline mileage were obtained by the Bureau of Mines from pipeline companies and information provided by the Interstate Commerce Commission. Crude-oil gathering lines, as of January 1959, were 40 percent of the United States pipeline mileage and totaled 75,182 miles, an increase of 1,656 miles during the three-year period. Crude-oil trunklines totaled 70,317 miles or 37 percent of the United States pipeline mileage, a decline of 8,277 miles from the 1956 total. Some of this loss is attributed to the converting of crude lines to refined products. Refined product lines in January 1959, totaled 44,483 or 23 percent of the United States mileage, an increase of 8,063 miles during the three-year period.

Jan 1, 1959

By C. Özgen Karacan

This study presents the results of core-log analyses from the exploration boreholes, the analyses of face advance rates, and the results of downhole monitoring studies performed in gob gas ventholes for calculation of changes in hydraulic properties in the longwall overburden at a mine site in southwestern (SW) Pennsylvania section of Northern Appalachian Basin. In the ?rst part of the study, coal measure rocks in overburden strata were analyzed and the locations where possible fractures and bedding plane separations would occur were evaluated. In the second part, the hydraulic conductivities were computed by two different slug test analyses methods using the water level changes measured in gob gas ventholes as longwall face approached. Hydraulic conductivities were analyzed with respect to the changes in overburden depth, the locations of the borehole, and mine face advance rates. These data were used to interpret the potential productivities of the gob gas ventholes as a result of fracturing and changes in hydraulic conductivities. The general results showed that the probability of fracturing and bedding plane separations in the overburden increase between strong and weak rock interfaces. Also, the probability of bedding plane separations increases as the interface is close to the extracted coal seam. Evaluation of slug tests showed that the hydraulic conductivity developments in the boreholes and their potential production performances are affected by the underground strata and the roof materials. In situations where the roof material is stiff and thick, the development of high permeability fractures around the borehole will be less. Results also indicated that borehole location with respect to face position affects the fracturing time and permeability evolution as well. Greater overburden depths generally cause earlier fracturing as longwall face approaches, but eventually result in lower hydraulic conductivities and potentially less effective boreholes. Increasing mining rates also resulted in generally lower hydraulic conductivities in the overburden. The results of this study were intended to improve the interpretation of gob gas venthole performance and to provide better siting of these boreholes.

Jan 1, 2009

By G. E. Walden

The Bureau of Mines is currently engaged in a continuing investigation of the thermodynamic properties of certain inorganic compounds. As a part of this investigation, the heat contents of bismuth and cerous chlorides were measured throughout the temperature ranges of 370° to 630° K. and 370° to 1,200° K., respectively. Equations representing heat contents as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate heat contents at selected temperature intervals ranging from the ice point to 650° K. for bismuth chloride and to 1,200° K. for cerous chloride; also, the heats of fusion of both compounds were calculated at their respective melting points. EXPERIMENTAL Materials The cerous chloride used in this investigation was supplied by the National Carbon Company of Cleveland, Ohio. A chemical analysis indicated Ce 56.57 percent and Cl 43.39 percent. No attempt was made to purify the compound or identify impurities since the analysis showed only about 0.04 percent total impurities. Reagent grade bismuth chloride was used without additional purification.

Jan 1, 1961

By Victor E. Kral

The Modarelli iron deposit , formerly known as the Requa iron deposit , is 44 miles by road south of Palisade , Nev . , on the Southern Pacific and Western Pacific Railroads . Construction of 10 miles of new road, which is necessary in case the property is exploited , will reduce this distance to about 28 miles . The deposit was discovered in 1905 , and patent was obtained in 1907 . The present owners obtained title to the property in recent years by paying the delinquent taxes . There has been no production . The ore deposit is a replacement of a Tertiary volcanic believed to be a rhyolite . Except for evidence of slight shearing , the deposit has no apparent structure . Hematite is the principal ore mineral ; it is fine-grained and is associated with very fine-grained apatite and unidentified minerals assumed to be alteration products of residual rhyolite minerals .

Feb 1, 1947

By W. E. Young, D. T. Delicate

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Nov 1, 1963

By M. S. Seehra, R. S. Pandurangi

"INTRODUCTION Silica and kaolin (a layer aluminosilicate) are among the major constituents of most coal mine dusts.' Whereas kaolin is cytotoxic in vitro but nonfibrogenic in vivo in humans and experimental animals,2-4 the cytotoxic and fibrogenic potential of silica is rather well established.5 Wallace and co-workers 6-8 have studied the cytotoxic potentials of both native and surface-modified silica and kaolin and inferred that retoxification is slow in the case of occluded silica vis-à-vis native silica. Recent epide¬miological studies indicate that silica concentration alone in a mine dust, as determined by transmission IR spec¬troscopy (TIRS), does not correlate well with the pro¬gression of coal workers' pneumoconiosis. 9 This obser¬vation has led to the suggestions that silica particles occluded by clays such as kaolin may not be fibrogenic. This proposal requires accurate estimations of kaolin, silica, and occluded silica. The current method of silica analysis in a mine dust sample employs TIRS of the 797- cm -1 band of silica, although its accuracy, as well as that of x-ray diffraction studies, is no better than 25 % , even in a laboratory-generated dust.° In this paper we have employed the techniques of diffuse reflectance spectros¬copy (DRS) and photoacoustic spectroscopy (PAS), in conjunction with an FT-IR spectrometer, for the quan¬titative determination of silica in laboratory-generated silica-kaolin mixtures.One of the main advantages of DRS and PAS is that, in these techniques, problems arising from sample prep¬aration of the KBr-based disks used in TIRS are avoided. There are, however, several other considerations (e.g., particle size effects and saturation phenomenon) which complicate the use of DRS and PAS for quantitative work. 10-25 In this paper, we have carried out a systematic comparison of the quantitative abilities of the two tech¬niques, as applied to the silica-kaolin mixtures, with par¬ticular attention to the saturation behavior of several bands with different absorption coefficients. In particular, we show that a weaker band for silica at 1875 cm-1 is suitable for quantitative purposes, and that quantitative accuracy is higher in DRS than in PAS. Details of this work are given below."

Mar 1, 1992

By A. E. Nagel, J. E. Carpetta, M. G. Zabetakis, T. D. Moore

The method of moving averages was found useful in assessing the nature of methane emission in coal mines. Emission rates were influenced markedly by the presence of abandoned oil and gas wells in the vicinity of the mine. Such wells appeared to increase the flow rate of methane into the mine by a factor of 2 to 30 in an active mine in the Pittsburgh coal seam.

Jan 1, 1972

In this U.S. Bureau of Mines report, in situ vat leach mineral recovery system concepts are described and cost compared with conventional mining and pad and autoclave leach processing systems. In the proposed systems, leachable ores are enclosed in place in reagent-impermeable in situ vat constructions. The ores are then rubbled and flood leached or flood oxidized and leached. The in situ vats are called stope leach or stope autoclave vessels. The report also proposes ore body-adjacent in situ vat constructions containing rechargeable processing stopes. A series of ore body-specific, innovative, and conventional mineral recovery systems case study designs are described and prefeasibility level costed. Based on a comparison of these prefeasibility level cost estimates, the proposed systems are determined to be economically competitive with conventional min¬eral recovery systems. The in situ vat leach mineral recovery systems concepts for leachable and refractory ores are developed around the drill-split narrow-vein and longwall mining methods described in part 1 of this Information Circular series.

Jan 1, 1995

By Patricia R. Devine

This report expands an earlier study by Jack Faucett Associates (OFR #40-88) of the same title. Both reports are based upon an interindustry analysis from 1963 through 1982, during which time U.S. metals consumption and production did not keep pace with economic growth. The report discusses three sources of change: technological change, economic growth, and composition of final demand, as well as the relative importance of the individual components of final demand for metals. The results show investment and personal consumption to be the most metal-intensive components of final demand, and technological change to be the major cause of decline in consumption growth during the study period. Technology change is defined as alterations in production processes resulting in more or less consumption of metal per unit of output, often because of material substitutions and design changes. A trade analysis shows the significance of import growth, particularly indirect imports (metal contained in imported goods) as a factor contributing to the reduced growth rate of domestic metal production. The effect of import growth is partially offset by indirect export growth, suggesting that continued increase of all U.S. exports can have a strong effect in reducing the negative trade balance in metals.

Jan 1, 1988

By D. J. Parker

State governments are increasing their efforts each year toward promoting the safety of miners .. Accidents underground are being avoided and mines made safer by means of revising and adding to their mining laws , by enforcing them through mine inspection departments , and by hearty co - operation with other agencies working miners ' safety . The U. S. Bureau of Mines is glad to testify to the co -operation that it receives from State mining departments in its safety work ; reports of the field mining engineers of the Bureau bear witness almost daily to the efforts of the States toward safety in mining . * This Through the courtesy of Mr. William Ogilvie , District State Wine Inspector of District No. 2 , with headquarters at "cAlester , Oklahoma, the Bureau has been furnished with a copy of a letter sent to various mining companies of Mr. Ogilvie's district in Oklahoma, relative to safety in Oklahoma mines . letter shows both the vigorous efforts which the State of Oklahoma is making toward increased safety in mines , and the recognized value of the types of electric cap lamps approved by the U. S. Bureau of Mines as " permissible " for use in gaseous mines ; it is accordingly reproduced in part : "hen during my first inspections of several coal mines in the district I found gas , or fire- darp being given off more or less constantly from the freshly cut coal at numerous points throughout the mines , I became uneasy relative to safety conditions , and am still considering your safety from many angles , but I am more concerned about the gas given off and the coal dust produced daily, than any other factor at the present time .

Jun 1, 1922

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

By David E. Nicholson

This report investigates the mechanical behavior of fine soils in a lunar environment in engineering gravity-flow bins. The ultrahigh vacuum, absence of moisture, and a lunar gravity one-sixth that of earth gravity represents a unique environment, both advantageous and detrimental to these systems. On earth, moisture and gases contained in powder masses can be responsible for complex descriptions of gravity flow. Their absence appear to simplify the lunar soil behavior. However, simulation of the lunar gravity and vacuum complicates the development of experimental data for designing bins. The properties of a dry soil powder, its behavior under one-dimensional compression, and its torsional and direct shearing strength under earth atmosphere are described in part 1 of this paper. These properties provide the parameters for a finite-element analysis to optimize the design of bins, to be described by Dr. William Pariseau in part 2. Shear tests assess the failure criteria for the material. Compression tests provide modulus and (Ko) stress-ratio values from the loading portion of the compression cycle, duplicating the condition of a bin at rest with the discharge closed. During the unloading portion of the compression cycle (soil overconsolidated), the residual Ko values rise. It is postulated that this phenomenon creates a high-lateral stress in bins when they approach incipient flow. Assessment of the Ko value, overconsolidation ratio, and the void ratio state is proposed as a criterion to determine the flowability of powder.

Jan 1, 1971

By W. F. Marshall

This Bureau of Mines report discusses tests conducted with four different catalytic reactor designs to determine the influences of exhaust treatment systems on emissions from diesel engines. Although there was significant differences in oxidation efficiencies at light to intermediate engine loads, all four catalysts were very effective in reducing emissions at heavy loads. Compositional determinations included carbon monoxide, carbon dioxide, unburned hydrocarbons, oxides of nitrogen, aldehydes, sulfur dioxide, sulfates, and particulate loading. Particulate size, exhaust odor intensity, and the character of the unburned hydrocarbon component were also determined.

Jan 1, 1978

By M. J. Ackerman

This study was undertaken to make a comparison between the cost of mining coal under roof bolt and under conventional timber methods of roof support. Studies were made at 14 mines in Pennsylvania, eastern Ohio, and northern and southern West Virginia. At each mine data were obtained for sections of the mine where the physical conditions, mining equipment, and mining systems were similar. Coal, recognized as one of the basic industrial fuels, is very competitive with other fuels, and management, in order to protect and enlarge its market, must be continually alert to find more efficient methods of production. Continuous production of coal is desired by all operators but never obtained. In mechanized mining the performance and production vary with operating time, which can be interrupted by many variable factors, such as condition of the roof, method of roof support, condition of equipment, water, ventilation, power, transportation, efficiency of operating crew, and supervision.

Jan 1, 1961

By Frank A. Peters

An evaluation is made of a lime-soda sinter process for extracting alumina from clay. In this process, alumina is extracted by sintering clay with soda ash and limestone and then leaching the sinter with a dilute sodium carbonate solution. The sodium aluminate solution formed during leaching is separated from the residue and treated with lime in autoclaves to remove dissolved silica before alumina trihydrate is precipitated with carbon dioxide. The tri-hydrate is then calcined to a-alumina. Two options, dry grinding and wet grinding, are used in the sintering step. The fixed capital costs for plants producing 1,000 tons of alumina per day are $72 million for the dry grinding option and $66 million for the wet grinding option on a Marshall and Stevens chemical equipment index basis of 240.0. Specific geographic locations of plant and raw material sources are not assigned, but, since this process requires large quantities of both lime-stone and clay, the plant site is considered as variable with relation to the clay mine and limestone quarry. A nomograph is given to find operating costs at various delivered costs of clay and limestone. If the plant is located nearer the limestone quarry so that the delivered cost of clay is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $76.47 and $71.61 per ton of alumina for the dry grinding and wet grinding options, respectively. On the other hand, if the plant is located nearer the clay mine so that the delivered cost of clay is $1 per ton and the delivered cost of limestone is $2 per ton, the operating costs are $80.15 for dry grinding and $75.34 for wet grinding.

Jan 1, 1967

By King K. Mak

The objectives of this study are to: (1) Assess current signing regulations and practices; (2) Develop effective signing guidelines; and (3) Evaluate the applicability and appropriateness of the proposed signing guidelines through field demonstration at representative mines. A literature search was conducted to determine the state of the art for signing applicable to surface mine haulage roads as well as survey of existing MHSA regulations and review of MSHA accident records. Nine representative mines were visited to gather information on current signing practices. Preliminary signing guidelines were then developed based on the abovementioned data. Field demonstration of the preliminary signing guidelines was conducted in which signing programs were implemented in two selected mines. Signing requirements were first assessed at each of the two participating mines. Subsequently, the necessary signs were designed, purchased, and installed at the two mines. Evaluation of the signing program as to its adequacy, appropriateness, and effectiveness was solicited from both mine management and operations personnel. Experiences gained from field evaluation were then incorporated into the final signing guidelines as presented in this final report.

Jan 1, 1981

By R. T. Johansen

The adverse effects on waterflooding and well-completion methods of clay minerals indigenous to petroleum-production formations recently have received considerable attention. Knowledge of the types and amounts of clay minerals present would allow estimates of the response of such formations to injected or infiltrated water; however, the random distribution of clays in sedimentary formations makes direct evaluation of ?water sensitivity? desirable. A method for the direct evaluation of water sensitivity has been developed, based on measurement of water-vapor adsorption. Correlation of such data with the results of nitrogen-adsorption measurements provides valuable information on the content and properties of clay minerals in sedimentary rocks. The method is relatively simple and has the advantage that it may be used with small, irregularly shaped chips or shale-streaked samples, as well as with typical core samples. Methods previously employed required separating the clay from the rest of the reservoir-sample material and then performing a clay analysis either by X-ray diffraction, differential thermal analysis, liquid permeability, or a combination of these methods (2,3) .3/ This water-vapor-adsorption method requires measuring only a few points on the isotherm to tell whether or not the sample is water sensitive. The goal of these measurements is not to determine the type or amount of clay present, but what will be its sensitivity to flood water. This method gives a direct means of solving this problem.

Jan 1, 1958

By M. J. Ferrante

Enthalpy and entropy increments above 298.15° K were determined for cop-per sulfate between 298° and 1,000° K and for copper oxysulfate between 2980 and 1,146° K by the method of copper-block drop calorimetry. Enthalpies, entropies, and heat capacities are tabulated for both compounds. In addition, free-energy functions are tabulated for the sulfate. Equations representing the enthalpies are given for each compound.

Jan 1, 1972

By J. D. Ramsdell

The study described in this report was undertaken to obtain information on the character and effect of antimony additions to titanium. The availability of high-purity, low-hardness titanium metal, resulting from fused-salt electrorefining techniques, permitted a reassessment and evaluation of the physical behavior of titanium-antimony alloys. Alloys, based on several grades of titanium containing up to 10 percent antimony, were arc-melted and processed to sheet by hot and cold rolling. Properties and characteristics were evaluated by hardness tests, hot and cold rollability, annealing treatments, metallographic examination, and tensile tests.

Jan 1, 1960

By P. A. Surgeon, R. R. Sayers

It is not the purpose of this report to try to describe all the work done during the past year for the improvement of health or the prevention of illness among miners , but to call attention to a few of the more outstanding investigations in which progress has been made . Among these , the investigations on the physiological effects of carbon monoxide , dust and ventilation , and temperature and humidity will be discussed . Carbon Monoxide . During the years 1920 and 1921 , much more work has been done on the various A survey phases of carbon monoxide than has been carried on for a number of years . of carbon monoxide poisoning in the American steel works , metal mines , and coal He conmines was made by Dr. Henry S. Forbes , of the Harvard Medical School . ** cludes from his survey that late after- symptoms following acute severe gassing rarely occur , and that almost always there is evidence of pre - existing pathological conditions when such effects do appear . He further states that he found no evidence of cumulative harmful effects resulting from frequent exposure . Dr. Forbes , Dr. Forbes , assisted by Louise Hompe , made a laboratory investigation in which anesthetized animals were exposed to carbon monoxide , illuminating gas , and benzol *** . The investigators conclude that , under the conditions of their experiments , there is no change in the coagulation time of the blood . It has been stated by many investigators that the blood of those affected by carbon monoxide does not clot as quickly as normal blood . While the investigation referred to above may not cover all the conditions , it is a valuable contribution to the subject as it indicates that the small hemorrhages found in the membranes covering the central nervous system , abdominal organs , etc. , at autopsy of those dying of carbon monoxide poisoning is probably not due to direct toxic action of the gas upon the blood .

Feb 1, 1922