Search Documents

By Tracy. L. D.

"Since the introduction of pulverized coal as a substitute fuel for natural gas in the various types of heating furnaces used, in steel mills, a number of fires and explosions have occurred, resulting in the loss of life and property.As one of the primary functions of the Bureau of Mines is to conduct investigations in the utilization of mineral substances with a view to increasing safety in the use thereof, it was deemed advisable to investigate the hazards involved in the industrial use of pulverized coal and, if possible, to devise methods of preventing future accidents arising therefrom. The knowledge of the explosive qualities of coal dust which the Bureau has gained in studies affecting dust explosions in coal mines was of material assistance in these investigations.Several plants were visited in which either fires or explosions had occurred, and data obtained as to the probable cause of the accidents.There was found to exist, among some of those employed about the furnaces, a lack of knowledge of the explosive and inflammable qualities of powdered coal.A small stream of pulverized coal leaking down from a defective joint in a coal transport line did not attract much attention, whereas, had a leak in a natural gas line occurred -wider similar circumstances, no doubt it would have had immediate attention.As a matter of fact, if by any means the duet cloud should come in contact with an open flame or hot metal, the effects would be as disastrous as if it had been gas.This is exceedingly well illustrated by an accident which came to the writer's attention. In the system used at this particular plant, the pulverized coal is transported to the furnace through compressed-air lines. The fuel is fed from a storage bin to a blowing tank in quantities as desired, after which compressed air is admitted and the powdered coal blown to the furnaces. At the time of the accident some repairs were being made to the tank, and it was supposed that the air pressure had been entirely released as the pressure gage stood at zero. There was, however, one or two pounds air pressure remaining and when one of the connections was taken off, a cloud of dust was blown across the room, 30 or 40 feet towards the drier furnace where it came in contact with some live coals. Immediately the entire room was filled with flame which rolled back and forth over a specs 50 feet or so in length."

Apr 1, 1921

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 190 psi, and with water-jet-assisted cutting pressures ranging from 1,000 to 6,000 psi. At water pressures of 3,000 psi and higher, dust concentrations were reduced by as much as 85 pct via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1986

By Irving Hartmann

When permissible explosives are used in coal mines according to the procedure recommended by the Bureau of Mines they are relatively safe, and no mine explosions are known to have resulted from this type of blasting. However, unsafe blasting practices - the use of nonpermissible explosives or the improper use of permissible explosives - have caused many serious disasters. In fact, such unsafe practices constitute the third most important cause (exceeded only by electricity and the use of open lights and smoking) of coal-mine explosions in the United States. During 1929-1947, inclusive, 81 explosions, resulting in 475 fatalities, were ascribed to unsafe blasting. The hazards of black powder, dynamite, and other nonpermissible explosives in coal mines have been recognized for many years, and attention has been called to this in numerous Bureau of Mines publications. Not only can these explosives ignite namable gas-air mixtures readily, but they can also ignite coal dust, as has been illustrated repeatedly in tests and at educational public demonstrations at Bruceton and elsewhere.

Jan 1, 1952

By Allen D. Look

In the prevention of accidents in milling operations, the proper installation and guarding of electrical and mechanical equipment, safe clearances, good housekeeping, adequate fire protection, adequate ventilation, dust and fume control, and good illumination, as well as safe practices, are essential. In the new concentrator of the Magna Copper Co., Superior, Ariz., many safeguards were incorporated and safe practices instituted to minimize accident hazards. The purpose of this paper is to describe some of these features and practices.

Jan 1, 1951

By Frederick C. Trutt

Research performed on arcing faults and their interaction; with electrical insulating materials within coal.-mine power-system enclosures is described. This work was performed at The Pennsylvania State University from 1 December, 1976 through 30. November, 1977. Results presented are interim in nature and future research is planned to integrate the simulations which have been constructed, as well as to apply developed experimental procedures to the evaluation of electrical insulating materials for use in coal-mine enclosures. The thrust of this research has been divided into several primary areas. These include the development of a theoretical procedure for computation of three-phase and line-to-line arcing fault currents as a function of time, formulation of an arc model based upon thermal-arc plasma properties so that arc voltages and energies may be computed, development of a simulation for pressure and temperature rises when an arc interacts with an electrical insulating material within an enclosure, experimental evaluation of electrical insulating materials in terms of their tendency to support an arc as well as their potential contribution to enclosure pressure rises, and integration of the above research areas to form overall procedures for theoretical and experimental evaluation.

Jan 1, 1977

By E. J. Matson

The Table Mountain copper deposit is in an isolated portion of north-eastern Churchill County, Nev. Although copper-bearing outcrops have been known to exist in the area since 1909, no copper ore has been mined. Development of the property has been hampered by poor roads and rugged topography. Until 1941, the last 4 or 5 miles to the property had to be traveled either by foot or pack animal. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a project was started at the Table Mountain deposit. The Bureau began its field work on July 29, 1947, and completed it on October 18, 1948. Thirteen holes aggregating 2,711 linear feet, were drilled; samples were analyzed - 509 from cores and 143 from sludges. This report contains a brief history of the district and a description of the geology, deposits, and drilling done by the Bureau.

Jan 1, 1949

By G. R. Hopkins

A recently completed survey , made by the Bureau of Mines to determine the trend of fuel consumption at refineries in the United States , showed the following outstanding points : A decrease in the use of oil for fuel in 1927 of over 5,000,000 barrels as compared with 1926 ; a decrease in the use of coal of over : 1,000,000 short tons ; small increases in the use of both natural gas and refinery gas ; an increase in the use of petroleum coke . The decrease in fuel - oil consumption was approximately 2,000,000 barrels each in the Atlantic Coast , Texas , and Louisiana- Arkansas districts , with an increase of 1,000,000 barrels in the Indiana - Illinois district , or a net decrease of 5,000,000 barrels . The decrease in fuel- oil consumption by refineries in the Texas and Louisiana- Arkansas areas was offset largely by increased consumption of natural gas and refinery gas , whereas the increased consumption in the Indiana- Illinois region was more than offset by the decrease in coal consumption . The use of coal for fuel declined from 6,052,000 short tons in 1926 to 5,031,000 short tons in 1927. Practically all of this decrease was recorded in the Appalachian and Indiana- Illinois districts , which at the same time showed the largest percentage increase in the use of oil for fuel . It is probable , therefore , that although coal prices also fell off , a considerable quantity of oil replaced coal in this area in 1927. In addition , the group of refineries , which are by location more or less definitely committed to the use of coal for fuel , undoubtedly succeeded in saving a material amount of coal through the use of more efficient fueling methods . A total of 130,815,000,000 cubic feet of natural gas was consumed for fuel at refineries in 1927. This represents an increase of 8 per cent over the 1926 total . Nearly all of this increase resulted from the opening of a line from the Monroe field to Baton Rouge , La . Had this line not been opened , there would have been a decrease in the use of natural gas , as a number of districts , particularly the Rocky Mountain , reported decreases in its use . The use of refinery or still gases for fuel did not change materially during 1927 , there being a total of 52,807,000,000 cubic feet burned as compared with 52,077,000,000 cubic feet in 1926. Refinery gases are largely a product of cracking and , it was probably more than a coincidence that a few districts in which cracking slowed down in 1927 also reported less refinery gas used as fuel .

Jun 1, 1924

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By J. W. Horne, W. L. Finley, A. D. Bauer, D. W. Gould

"The Bureau of Mines and the State of Colorado are cooperating in an investigation of the oil shales of Colorado. in this report the yields and the results of analyses of the oil and, gas produced from a number of oil-shale samples from the principal deposits of Colorado and other oil-shale States, are compared with samples from Scotland and Australia, where the oil-shale industry has had its greatest commercial development, and also with a sample from Brazil *here extensive oil-shale deposits are found shale samples were not selected as being representative of the different deposits, but they illustrate the wide variation in the nature of the organic matter of different oil shales.A further study is being made of the chemical composition of the shale, distribution of nitrogen and sulphur. in the products, temperatures at which organic matter decomposes, and the results will be presented in subsequent Papers, With complete data available on the chemical composition of the shales, it may be possible to explain some of the differences in the nature of the products from the various shales,Most of the work described herein was done under the supervision of M. J. Gavin. L. C. Karrick, formerly of .the Boulder laboratory, assisted in the work and gave many valuable suggestions."

May 1, 1924

By G. E. McElroy, D. Harrington

In connection with the cooperative metal-mine dust and ventilation investigations of the U. S. Bureau of Mines and the U. S. Public Health Service , some underground data have been obtained with intent to ascertain the adaptability of the katathermometer for determining the comfort of working places in mines . This preliminary study indicates that the instrument will probably be useful for making routine determinations of comfort conditions in our mines , and that it may also prove an important accessory for investigative work on problems in ventilation and kindred subjects ; in both coal and metal mines , although the instrument should probably be altered somewhat for maximum utility under the varied conditions in the mines of the United States . The katathermometer is an instrument contrived by Dr. Leonard Hill , an eminent English physiologist , and its various features have been fully described by him in his book entitled " The Science of Ventilation and Open Air Treatment . " He made exhaustive experiments and concluded that the rate of cooling of the human body was the controlling factor in determining comfort or discomfort , and then set out to make an instrument that would measure this rate of cooling . The resulting instrument the katathermometer measures its own rate of cooling when its temperature approximates that of the human body and thus serves as an index of the rate of cooling of the body itself . - The instrument consists of an alcohol thermometer having a cylindrical bulb 1 inches long and 3/4 inches in diameter, and a stem about 8 inches long graduated from 95 to 100° F. This temperature range gives a mean temperature of 97.5° F. ( 36.5° C. ) , which is approximately that of the clothed body surface . The stem terminates in a small reservoir which serves the double purpose of acting as a safety overflow in case of overheating the bulb , and of insuring a regular rate of cooling by the time the meniscus has fallen to the 1000 point .

May 1, 1922

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist, and in locating them quickly with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By James C. Cawley

This report presents results of recent Bureau of Mines research to establish the probability of spark ignition as a function of current (or voltage, for capacitor circuits) for resistive, inductive, and ca-pacitive circuits in 8.3% methane-air atmospheres. The data presented quantify the explosion hazard created when low-power electronic devices catastrophically fail in an explosive mine atmosphere. Previous litera-ture dealt with levels of probability between 10-3 and 10-4. This re-port extends the probability data to levels as low as 10-7. This study has verified that when the probability of ignition, PI, is plotted on a log-log coordinate system versus the current (or voltage), a continuous, straight-line relationship is formed. An interesting result that can be statistically hypothesized is that at some low level of igniting current the ignition process ceases altogether.

Jan 1, 1988

By Henry M. Harris, John E. Kelley, Thomas D. Roberts

A penetrometer apparatus for measuring viscosity of glass at temperatures up to 1,450 ° C was developed for use in establishing the viscosity coefficients required for high- temperature forming of ceramic materials . The major advantage of the method is that it can be used with samples of almost any shape or size without the necessity of forming or measuring shapes to close dimensional tolerances . Also , it has proved accurate in the range of 106 to 109 poises , a gap between the normal limits of other methods . The device , which operates on a single penetrometer principle , was used to determine the absolute viscosity coefficient of substances in centimeter - gram- second units of poises instead of relative penetration - rate units as with other penetrometers . Penetration of the viscous sample was sensed with a linear , variable differential transformer . The output of this transformer was recorded versus time , and the penetration rate was used in calculating the viscosity coefficient . The general equation relating penetration rate and viscosity coefficient was found to be 11 = F ( ln L/a 0.72 ) 2 π UL · where is the viscosity coefficient in poises , F is the penetrator load in dynes , L is the penetration depth in centimeters, a is the penetrator radius in centimeters and U is the penetration rate in centimeters per second . The penetrometer was tested using a standard viscosity sample of sodalime - silica glass obtained from the National Bureau of Standards ( NBS ) . Values obtained at several temperatures all agreed within 10 percent with comparable data calculated from the Fulcher equation derived by NBS for this glass . Equivalent accuracy was obtained with other glasses used to evaluate the apparatus .

Jan 1, 1964

By IRENE AITKENS

The emerald is the most costly of all gems , due to the scarcity of flawless stones . This fact gave rise to the ancient axiom , " As rare as an emerald without a flaw . The finer gems not only command the highest prices at all times , but when flawless are considered the most highly prized of all gem stones . George F. Kunz divides emeralds into two distinct classes : " Exceptional specimens , " which bring as much as $ 6,000 a carat ; and " fine- quality specimens , " which bring about $ 1,000 a carat .

Jul 1, 1931

By Ben E. Lindsly

The study of "bottom-hole samples follows in natural sequence the study of samples obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1930, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs.. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, That physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing Tells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental data were obtained in the study of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at higher pressure, and later became mixed with the original undissolved gas.

Jan 1, 1933

By J. C. Meeks, C. L. Klingman

An instrument that is sensitive , portable , safe , and low in cost was developed by the Bureau of Mines for detecting helium leaks by comparing the thermal conductivity and flow rate of the atmosphere around the suspected leak against a reference of helium- free air . A vacuum pump pulls the sample gas through a restriction and over thermistor elements , the combined electrical output of which is affected by thermal conductivity and flow rate of the sample gas . Tests showed that the battery - operated Helium Leak Detector was effective and rugged instrument that could be operated safely in explosive atmospheres . The instrument could also detect , but not identify , other gases such as methane , hydrogen , argon , carbon dioxide , and Freon 12 .

Jan 1, 1964

"Contained in this chapter is a listing of the publications and reference books which have come about as a result of respirable dust research performed by faculty, staff and graduate students in the Generic Mineral Technology Center for Respirable Dust at The Pennsylvania State University, West Virginia University, University of Minnesota, Massachusetts Institute of Technology, and Michigan Technological University. These publications have appeared in scientific journals, proceedings of the national and international symposiums, and professional meetings. Complete citations of the publications can be found in Volumes 3 through 6 and Volume 8 of this series. The agenda of the last annual GMTC seminar, held at West Virginia University on February 1 - 2, 1988, follows. The project presentations are organized under the five research areas. All projects currently active were presented to the Advisory Committee. New project submissions were not. The authors were allotted thirteen (13) minutes for their presentations; the remainder of the twenty (20) minutes allotted for each project was used for introductions, transitions, and questioning by the Advisory Committee. Each author used a standard format for presentation of his/her materials for review; handout materials were distributed to the Advisory Committee for reference. Opening remarks were made by Dr. Richard Bajura of West Virginia University and Dean Robert L. Frantz and Dr. Raja V. Ramani of The Pennsylvania State University.The Generic Mineral Technology Center for Respirable Dust is funded by the U.S. Bureau of Mines through the Mining and Mineral Resources Research Institute Program. The opinions and conclusions expressed in these papers are those of the authors alone and do not represent the opinions of the Generic Mineral Technology"

Aug 31, 1989

By F. P. Haver

The purpose of this investigation was to determine the effect of common impurities, that is, oxygen, nitrogen, carbon, and iron, on the Brinell hardness of electrolytic titanium. On a weight basis, nitrogen had the greatest hardening effect, followed by oxygen, carbon, and iron in order. The hardening effects of oxygen and carbon were almost identical up to a concentration of approximately 0.1 percent by weight. Above this concentration, the relative hardening effect of carbon decreased rapidly, possibly because of its limited solid solubility in a-titanium. Hardness vs. composition curves for both oxygen and nitrogen were essentially straight lines over the range of Brinell hardness numbers (B.h.n.) covered in the investigation. The hardness of titanium was also determined as a function of the percentage of impurity atoms. On this basis, iron in concentrations up to 0.17 atomic percent had a greater hardening effect than either oxygen or carbon. INTRODUCTION Determination of the as-cast hardness of arc-melted titanium is a method of quality control widely used in industry. Numerous studies4/ have been made of the effect of impurities on the hardness obtained by this method. However, most of them have been based on the use of either iodide titanium or commercially pure Kroll sponge (B.h.n. >90), as a starting material.

Jan 1, 1959

By K. C. Dean

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Stabilization has been attained by physical, chemical, vegetative, and combination procedures. Vegetative reclamation is preferred to physical and chemical stabilization but is diffi¬cult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Methods now have been developed for attain¬ing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $120 to $650 per acre. The cost for stabilizing tail¬ings requiring more intensive treatment techniques may range upward to $1,750 per acre. This report summarizes procedures developed by the Bureau of Mines and industry for vegetating amenable tailings, lists costs for the various processes, and suggests procedures that may be applicable for stabilizing saline and pyrite-containing tailings. Ridged planting beds, drip irrigation, and deep-furrow planting techniques are suggested for stabilizing saline wastes. A combination of mill tailings and sewage sludge can be used for pro¬ducing synthetic soils, and layers of sewage sludge buried under a layer of tailings offer promise of inhibiting acid formation from oxidation of sulfides in mineral wastes.

Jan 1, 1974

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steel in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steel as impurities. For example, silicon additions form SiO2 or combinations of SiO2 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MnO, SiO2, and Al2O3, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods. The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932