Search Documents

By J. F. Neill, O&apos

[The Cartersville mining district is in Bartow County, Ga., about 40 miles northwest of Atlanta. Barite, limonite, ocher, amber, hematite, and, manganese oxide ores have been produced from the strict since about 1840. In the search for a possible source of manganese ore, Bureau of Mines engineers made a preliminary study of the district from September 1950 to January 1951. During this study 139 deposits were examined, and many mineral exposures were sampled. Manganese mineralization occurs as fine oxide and concretionary pellets in residual clays, as fine oxides in umberous clay, in brown-iron deposits, and in a limited quantity in mud ponds and Jig-tailing piles. The future supply of ferrograde manganese ore from the district, using current mining and benefication methods, appears limited to the recovery of the hard manganese ores deposits. Rough estimates indicate a reserve of manganese-bearing clays of about 8,000,000 long tons. This type of deposit has been extensively exploited and the larger deposits mined out to depths of from 50 to 200 feet. The remainder of these deposits are low grade, are covered with deep layers of colluvium, or lie below the ground-water table. Any future production from this source will require systematic prospecting, improved concentration, and an increase in the price of concentrate.]

Jan 1, 1954

By John Ward Smith

Variations in specific gravity of oil retorted from oil shales of the Eocene Green River Formation in northwestern Colorado were evaluated statistically, demonstrating that these variations are very strongly associated with stratigraphic position and less strongly but still significantly associated with geographic location. Specific gravity of oil retorted from these oil shales apparently varies with the carboxyl group content of the oil shale's organic matter. Higher temperatures accompanying increasing depth of burial probably progressively decarboxylated oil shale's organic matter producing the decrease of oil specific gravity associated with deeper stratigraphic position. The geographically associated oil-gravity variations were probably produced by regional variation in the original thickness of late Cenozoic extrusive rocks once overlying the Green River Formation.

Jan 1, 1966

By John Nagy

The effect of low percentages of methane (0 to 5 pet.) in an air atmosphere on spark initiated explosions of coal dust was investigated. With low dust concentrations (0.1 to 0.4 oz./cu, ft.), small amounts of methane increase the explosion pressure; with larger dust concentrations (0.5 to 2.0 oz./cu. ft.), small amounts of methane decrease the explosion pressure. The rate of pressure rise of a coal dust explosion increases with increase in methane concentration; about 3 to 4 pct. further addition of methane yields a decrease in the rate of pressure rise. Convection currents created by the air or gas blast used to disperse dust produce an increase in explosion pressure and rate of pressure rise. The minimum explosive concentration of the coal dust decreases about linearly as the concentration of methane increases from 0 to 5 pct. The explosion pressure increases linearly as the initial pressure within the chamber increases. Similarities between coal dust and methane explosions are indicated, INTRODUCTION During coal mining, methane occluded in coal or adjoining strata is liberated into the mine atmosphere,4 Normally, the methane is diluted and swept away by the ventilating air. Under some conditions, through accidental disruption of the ventilation system, sudden outburst, or because insufficient fresh air is supplied to a working place, low percentages of methane may be present during mining operations. If it is permitted to accumulate, methane itself presents an explosion hazard; its limits of explosibility arc approximately 5 and 15 pct. The effect of low percentages of methane on the explosibility of coal dust was studied to provide a broader understanding of the hazards of ignition and explosion and thus to facilitate development of control

Jan 1, 1961

By D. G. Willard

The U.S. Department of Interior, Bureau of Mines has evaluated the potential resource and annual availability of cobalt from 27 deposits or districts in 11 market-economy countries. More than 95 pct of primary cobalt production from market-economy countries, mainly byproduct output from copper and nickel operations, was analyzed. Approximately 1,200,000 mt of cobalt is potentially recoverable at the demonstrated resource level. Very large additional resources exist, especially in laterite deposits, but are at the inferred level. The producing operations evaluated in this study are expected to produce about 19,000 mt of cobalt in 1989, significantly less than the available capacity of about 31,000 mt. More than 14,000 mt per year of cobalt is produced from copper-cobalt deposits in Zaire and Zambia, of which 11,000 mt can be produced at a copper price of $O.60jlb or less with a O-pct discounted cash-flow rate of return (DCFROR). Approximately 4,400 mt of cobalt is produced annually from nickel-cobalt deposits in six countries, of which about 1,800 mt (in Canada and Brazil) could be produced at a nickel price of $1.50jlb or less at a D-pct DCFROR. Approximately 200 mt per year of cobalt is produced from a cobalt mine in Morocco. Most of the evaluated nonproducing operations and prospects that could potentially produce cobalt as a principal product or byproduct would require a total cost (including a 15 pct-DCFROR) significantly exceeding January, 1989 market prices of the principal commodities. Principal-commodity dependence, transportation routes, cobalt toxicity, and other issues that could affect the availability of cobalt are addressed herein.

Jan 1, 1991

By M. Orchin

THIS PAPER is concerned with two aspects of the behavior of coal: (1) Dispersion by solvents atmospheric pressure and high temperature and (2) the destruction and regeneration of the coking properties of coal. Several pure polycyclic compounds and a coal-tar fraction were found to extract 95 percent of the organic material of a bituminous coal. About 20 percent of the extract was soluble in benzene, and this fraction contained the ?coking principle? of the coal. From an extensive chemical spectroscopic, and x-ray study of the benzene-soluble material, some conclusions could be drawn concerning the composition and structure of this fraction of coal. A possible commercial application of the extraction technique is in the preparation of low-ash carbonaceous material for the manufacture of electrode carbon.

Jan 1, 1951

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By W. W. Adams

"The third annual safety contest for plants producing sand and gravel, which was conducted in 1911 by the United States Bureau of Mines in cooperation with the National Sand and Gravel Association, registered further progress in safety as compared with the two previous annual contests. Both the accident-frequency rate and the accident-severity rate were reduced.The period covered was the calendar year 1931; sixty plants participated, and 17 States were represented by the participating companies.The contest covered accidents and man-hours worked by all men at the participating plant who were employed by the same company; and it included work up to the point of delivery of the material directly to the consumer or to an independent agency of transportation--in other words, to the point of relinquishment of control of the material by the producer.The purpose of the yearly contests for producers of sand and gravel is to aid in the promotion of safety among the employees and in the reduction of accident costs to the companies. The contests develop friendly rivalry among the various plants and among the employees of individual plant in a concerted effort to prevent accidents.Two safety trophies are awarded annually, both of which are provided by Rock Products magazine. One of the trophies is for the host safety record among plants that were in operation the contest year 100,000 or more man-hours; the other trophy is for the best among plants that were in operation lees than 100,000 man-hours. Awards and the relative standing of the various plants are based upon statistical compilation by the Bureau of Mines of accident reports and employment reports furnished by the enrolled companies. are summarized at the close of each year, and the summaries are submitted to each company concerned for certification as to the accuracy of the summary and the completeness of the company's reports from which the summary was prepared. When the summery is returned signed by an official of the company, the records are considered to be a trustworthy basis for determining the relative standing of the various plants. The position of each plant is determined by its accident-severity rate; that is, the number of days of disability resulting from accidents for each 1,000 men-hours of work done by all employees at the plant."

Aug 1, 1932

By Charles W. Huggins

Knoop hardness indentations were studied and measured with the electron microscope on TiB2, HfC, and A1B12 crystals. A detailed description of replicating the indentations using collodion and Faxfilm is made. A John Hopkins grating having 28,800 lines per inch was used to accurately determine the magnification used on the electron microscope. The primary objectives were to prepare carbon replicas of hardness indentations, to measure the indenations accurately, and to compare the results with those obtained with the light microscope. The resulting data showed excellent agreement between the measurements made on the replicas with the electron microscope and those made with the optical microscope. The replicas made from collodion showed slightly better agreement with the light optical values than did the replicas made from Faxfilm.

Jan 1, 1963

By H. N. Dunning

A comprehensive production research program, now in progress at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville, Okla., includes studies of the displacement of petroleum from sand by detergent solutions. An earlier report (12)2/ presented the results of an extensive research program to determine the value of detergents as floodwater additives. This report presents later results of the detergent-testing program (13, 17). Although water-flooding methods and controls are constantly being improved to increase the production of oil from secondary-recovery operations, considerable crude oil commonly remains.in place after a water flood has been terminated. Therefore, the possibility of improving the efficiency of a waterflood by the use of detergents is of increasing interest. The effects of many substances on the efficiency of water flooding have been investigated in laboratory studies (5, 11, 13, 17, 19, 24). Of the various sub-stances tested, only surface-active agents were consistently effective in removing oil from sand. Results of laboratory studies presented in earlier reports (9, 11, 12, 13) show that many detergent solutions effectively displace petroleum from sand surfaces under varying conditions encountered in centrifuging, manual and mechanical agitation, ultrasonic vibration, and imbibition.

Jan 1, 1957

By Mark Sheppard

[Considerable research work has been done on secondary crushing and coarse rued fine grinding, and the literature on the general subject of crushing contains many references to the work of investigators on the laws governing end the factors entering into the economical production of fine materials. However, little information on primary crushing in available. The literature deals mainly with problems and practices in ore dressing, end in this field the engineer or investigations is concerned largely with the production of fine material rind the unlocking of minerals in the ore. Under such conditions close control of screen sizes of primary-crusher products is a secondary consideration and has received very little attention. The growth and development of tae nonmetallic industries have drawn more attention to primary crushing. Many of these industries are interested is the production of a minimum amount of fines and a maximum amount of a coarse Product that meets certain definite size specifications, a condition entirely different from that in the field of ore dressing. Under such conditions tae proper type of primary-crushing equipment and a knowledge of the factors governing the operation of such equipment nest are essential to economical production of a satisfactory material.]

Jan 1, 1938

By G. W. Birge, D. E. Wolfson, J. G. Walters

Seventeen samples were carbonized by the BM -AGA pilot - plant test method and in industrial ovens . Chemical and physical properties of the samples were determined , and the physical properties of the cokes prepared by the two methods were compared . Since the capacity of the plants from which these samples were obtained is about 30 percent of the 1959 total for the United States , the data given in this report are indicative of the chemical and physical properties of blends used to produce industrial cokes and the acceptable chemical and physical properties of the resultant coke .

Jan 1, 1964

By F. D. Everett

The Federal Bureau of Mines reviewed the status of tungsten deposits of Utah in 1959. Industrial requirements of tungsten during emergencies have exceeded the domestic supply, and a knowledge of the sources of this strategic element may be helpful in the future. Tungsten occurs as the mineral scheelite in deposits that have been developed or explored on approximately 60 properties in 10 of the Great Basin ranges of Utah, none of which were being worked in 1957-59. Ores from most of the productive areas are similar in that they are contained in tactite deposits on or near the contact of calcareous and acidic intrusive rocks. The tactite ores consist predominantly of the silicate minerals garnet, epidote, and diopside and the carbonate rocks limestone or dolomite. Scheelite, where present, is disseminated irregularly in the tactite. Tungsten ores from Utah mainly have been produced from small deposits worked in World Wars I and II and the Korean campaign. The ores were either hand sorted to a grade ranging from 0.5 to 1.0 percent tungsten trioxide (W03) or were beneficiated in small mills to higher grade concentrates. The largest reserve appears to be in the area of the Notch Peak intrusive in the House Range, Millard County. A large part of the reserve in the House Range is mineralized tactite containing 0.2 to 0.3 percent W03. Research on flotation by the Bureau of Mines has indicated a method of concentrating scheelite in tactite ores that average 0.25 percent W03, with at least 85 percent recovery. The concentrate assays more than 5 percent W03 and can be processed into artificial scheelite ready for industrial use.

Jan 1, 1961

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By Robert F. Chaiken

The Bureau of Mines is using model ducts lined with coal to study the nature of coal mine fires, their rate of propagation, their influence on ventilation airflows, and their response to sealing and other fire suppression measures. For scale-modeling purposes these studies are being carried out in various size ducts; eventually they will include a full-size mine entry in the Bruceton multiple-entry Experimental Mine. To date, work has been carried out in an insulated 9.l-m-long duct with a 5-cm thickness of coal leaving a 23-by 23-cm square opening for air ventilation. Fire propagation processes in this duct were mainly transient in nature owing to the relatively small length-to-diameter ratio. This report describes the experimental equipment employed and the results obtained to date.

Jan 1, 1979

By W. H. Oppelt

The Federal Bureau of Mines investigated combustion of lignite in domes-tic heating equipment to obtain information on equipment performance and to evaluate testing procedures. Three types of domestic heating equipment were tested, ranging from a hand-tilled, magazine-type space heater to a ram-type overfeed stoker. Lignite was readily burned in each of the three units under various test conditions. Burnoff rates determined by adding weighed charges to the magazine were found to be in error because of shrinkage of the lignite when only a portion of the magazine capacity was consumed during a test. More reliable burnoff rates could be determined by carbon-nitrogen balances. A hand-fired magazine-type space heater (Booker heater) was operated without the furnace attachment at efficiencies to 75 pct. One test series was run with minimum supervision under conditions encountered in actual household operation. No mechanical trouble was encountered.

Jan 1, 1960

By V. F. Parry

The major industrial uses of char or semicoke produced by low-temperature carbonization of coal4/ are as fuel for generating electric power, for blending with metallurgical coking coal as a substitute for low-volatile coals, and for gasification to produce synthesis gas for chemical purposes. This paper discusses various methods for carbonizing coal, emphasizing processing of the noncoking coals to produce char for thermal power-plant fuel and for blending with metallurgical coking coals and tar for chemical use. Low-temperature carbonization is a relatively simple processing step involving heating coal to about 900° to 1,200° F. to decompose the coal into 4 main products: (1) Semicoke or char; (2) complex, partly oxygenated liquid hydrocarbons or tar; (3) fixed gases; and (4) water. If the coal is heated rapidly under conditions that prevent decomposition of the primary products, 68 to 87 percent of the net heat in the raw coal is left in the char and 10 to 23 percent of the potential heat appears in the primary tar. Fixed gases represent approximately 7 percent of the heat and approximately 2 percent is lost or dissipated in the reactions of decomposition. Considering the different ranks of coal in the United States, the yield of tar will vary from about 9 to 44 gallons per ton, therefore it is important that each coal be carefully considered if it is to be carbonized for industrial use.

Jan 1, 1955

By C. M. Mason

The methods currently used by the Bureau of Mines to evaluate the sensitivity, strength, incendivity, gaseous products, and physical properties of explosives and hazardous chemicals are described. Included are the tests used to evaluate explosives which arc certified as permissible for use in underground coal mines.

Jan 1, 1972

By Charles M. McCulloch

This Bureau of Mines report discusses the principles of using computers to draw maps and plot geologic data of mining areas. The types of maps that can be drawn by a computer are reviewed, using as examples two separate areas where poor roof and gas emissions caused mining problems. Such maps can be used not only to help identify problem areas, but also to predict areas where problems could occur, thus giving mine operators time to work out solutions prior to mining. The average cost of a computer-drawn map for a mine property is less than $100, including computer time and man-hours for data preparation.

Jan 1, 1976

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2 ) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs' estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By Larry A. Haas

The U.S. Bureau of Mines, in cooperation with Cleveland-Cliffs, Inc. (Hibbing, MN), investigated ways of enhancing the quality (compressive strength, after-tumble and reducibility) of domestic acid and fluxed magnetite pellets by modifying the oxygen content during the preheat and induration periods of the firing operation . Oxidation of magnetite was best accomplished when sufficient oxygen and time were available before the peak induration temperature was reached. The rate of magnetite oxidation increased directly with the gas oxygen content during the preheat period at 7000 C and above. With 30 pct ( or more) O2 and a preheat rate of 2000 C/min, most of the magnetite was oxidized during the preheat period. With laboratory tube and mini-pot furnace tests, oxygen enrichment during the preheat period improved the pellet properties more in the simulated grate-kiln tests than in the simulated straight-grate tests. The longer induration period with the grate-kiln test resulted in more sintering of the residual magnetite and its reaction with the silicon compounds. When flux was present in the pellets, calcium silicates and calcium and magnesium ferrites were formed. More calcium ferrite was formed when the magnetite was oxidized early and less iron was present in the fayalitic calcium silicate slag.

Jan 1, 1993