Search Documents

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

By Launa G. Mallett, Jr. Brnich

Overview: The first step to emergency preparedness and maintaining a safe workplace is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen at one time. Risk assessment can be used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. Purpose: This training package was developed to assist instructors as they (1) determine how to use risk assessment to improve safety preparedness and (2) present risk assessment concepts and tools to trainees. The concepts and tools presented here can be applied to any mine hazard.

Jul 1, 2003

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By J. F. McIlwain

As part of its goal to minimize the requirements for critical materials, the Federal Bureau of Mines has investigated the consolidation of an iron-base superalloy (20 pct Cr, 5 pct each Ni and Mn, 1 pct each C, W, Mo, and Cb, and the balance Fe) and its modifications by powder metallurgy (P/M) techniques. Vacuum-atomized, prealloyed powder was used. Consolidation was by sintering of cold-pressed alloy powder, or by forging plus rolling or extrusion of canned powder. Several commercial lubricants were evaluated in the pressing operation. At 50-tsi compacting pressure with up to 3 wt-pct lubricant, green strengths did not exceed 1,000 psi. Powder sintered just below the solidus temperature attained a tensile strength of 69,000 psi and 4 pct elongation. Liquid-phase sintering produced higher densities, lower tensile strengths, and nil ductility. Canned powder was forged and rolled at 1,200° C, yielding a 100-hr rup¬ture strength of 9,800 psi at 815° C and a room-temperature tensile strength of >130,000 psi at 6 pct elongation. Heat treatment of modified P/M iron-base alloy containing 0.63 pct C resulted in a 100-hr rupture strength of 17,000 psi. Oxidation resistance at 805° to 815° C of the forged and rolled P/M iron-base alloy was similar to that of the cast iron-base alloy and supe¬rior to conventional stainless steels.

Jan 1, 1981

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By Henry P. Chandler

THE year 1950 was one of increased activity in almost all branches of the abrasives industry, with nearly all abrasive materials showing a marked increase in tonnage and value. New records were made In the production of tripoli, ground sand and sandstone, pumice and pumicite, and garnet. Total production of crude artificial abrasives in the United States and Canada increased 17 percent in tonnage and 30 percent in value. Imports of industrial diamonds increased 100 percent in total value and 72 percent by weight, the 1950 importation being the largest since 1944. Imports of corundum increased 76 percent in tonnage and 4 percent in value.

Jan 1, 1953

By W. Timothy Adams

The production of natural abrasives varied in quantity and value compared with 1976. Output of tripoli-type materials was approximately the same in both quantity and value. Special silica stone products decreased in quantity and increased in value. Garnet production decreased both in quantity and value. The production of emery increased and the production and value of manufactured abrasive material was approximately the same. Foreign Trade Imports of abrasive materials were 23% more in value than in 1976, and exports plus reexports increased in value 10%. Net imports, the excess of imports over exports and reexports, were $35.3 million. The volume and value of all abrasive materials exported varied.

Jan 1, 1980

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1951

By William O. Vanderburg

This report 3/gives the results of a reconnaissance of the mining districts in Lander County, Nev., made from March 29 to April 20 and from May 9 to May 21, 1938, during which virtually all of the mining districts n the county were visited. No attempt has been made to include in this report all the mines and prospects in the various mining districts, and it should be stated that whether or not a property is mentioned herein has no. bearing on its merits. The report rovers the situation of the various districts, types of ore deposits, ownership and description of mines and prospects, information on past and current activity, and other information of economic interest likely to be useful to those interested in the development of our mineral resources. The names of the various districts mentioned are those generally used when they were organized for purposes of record and regulation. When originally organized, the districts embraced large areas with no well-defined boundaries, so that the names have little geographical significance.

Jan 1, 1939

The Production Profile Program is written for use on a Digital Model PDP 11/70 computer using a Fortran IV level G language. It may be run on any system which uses G level or an upward compatible version of Fortran IV language. Please note, however, that the Model PDP 11/70 for which the program was written is programed to read DEC026 type keypunching. If the user's computer is programed for another type of keypunching it may be necessary to re-keypunch the Production Profile Program. The Production Profile Program uses a fourteen card input. The data must be keypunched according to the layout described in detail in the multiple card layout forms (following). The output from this program must be printed on wide paper, as a full 120 columns are used. The samples of output at the back of this appendix have been reduced for inclusion in this report.

Jan 1, 1977

By M. Kawahata

Methane sensors using principle of catalytic oxidation of methane are employed for determination of methane content in ambient air of coal mines. Certain foreign gases or vapors in the air poison the catalyst of the sensor effecting the sensor's response. After literature search of poison compounds of Pt and Pd oxidation catalyst, experimental studies of catalyst poison kinetics were made for three siloxane compounds, tributyl-phosphate, monobromotrifluoromethane, and hydrogen sulfide, selected as poison vapors. Concentration range of the poison vapors was varied in a range from 3000 to 0.1 ppb (v/v). Three siloxane vapors produced strong catalyst poison effect, followed by tributylphosphate, hydrogen sulfide and monobromotrifluoromethane for the high concentration level of the poison vapors. The poison effects are influenced significantly by concentration of the vapors. Threshold poison vapor concentrations where effect of the poison vapors on the sensor is minimal were determined experimentally. Experimental studies were made further for prevention method of catalyst poison by adsorption techniques. Use of activated carbon cloth inserted on the sensor's head prevented catalyst poisoning efficiently.

Jan 1, 1981

By Fred W. Snow

This paper describing the mining practices at the Magma mine, Superior, Ariz., is one of a series being prepared by the Bureau of Mines on mining prac¬tices, methods, and costs in the various mining districts in the United States. At present (1929) practically all the mineral production in the Superior district is from the Magma mine of the Magma Cooper Co. The ore is mined for its copper but contains associated silver and gold. Both direct smelting ore and ore of concentrating grade are produced. The mining methods now in use at the Magma mine were adopted or developed as knowledge was gained of the physical condition of the ore bodies and the inclosing formations; the wall rock is soft and crushed and the ore is relatively hard. In general, existing methods have been adapted to fit local conditions, but some of the mining practices used were originated at this mine. Most of the ore is mined by a combination of rill stopes and pillar stopes. The pillars are extracted by underhand mining.

Jan 1, 1929

By George S. Rice, F. B. LANEY, A. J. Lanza, Edwin Higgins

Under its organic act the Federal Bureau of Mines is directed to conduct investigations relating to the improvement of health conditions in the mineral industries. This report describes the lead and zino deposits and the mining methods employed in the sheet-ground area of the Joplin district, Missouri, and discusses the causes and the methods of abating rock dust in the mines, the chemical and physical characteristics of the dust, and the quantities present in mine air. Although the preliminary investigation included a number of the "soft-ground" mines, the writer spent the larger part of his time in the sheet-ground mines, for in them alone was siliceous dust found in appreciable quantities. Some results of the preliminary investigation have been published by the Bureau of Mines in Technical Paper 105.a The territory covered in t~lCpreliminary investigation, during the period between November 7 and December 6, 1914, embraced parts of Jasper, Lawrence, Newton, and Greene Counties, Mo., and outlying districts in Kansas and Oklahoma. The remainder of the field work, to which 84 days during the period from February 9 to July 19, 1915, were devoted, was confined to the sheet-ground mines, the most important of which are situated in the vicinity of Joplin, Webb City, Carterville, and other smaller near-by towns in Jasper County, Mo.

Jan 1, 1917

Objective: To provide a safe, practical, cost-effective method for measuring coal rib thickness during highwall mining.

Jul 1, 2008

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936 and their rapid development have brought tine problem of brine disposal to the foreground in that State. The ultimate magnitude of the is not yet known, but already it is great enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field brines in Illinois and has studied in detail three subsurfaces disposal systems.]

Jan 1, 1940

By Mark L. Chatman

This report presents an economic mineral assessment and Inventory of mines and prospects In the approximately 176,000-acre Patagonia Mountains-Canelo Hills Unit of Coronado National Forest. Deposits or areas most likely to experience future development are characterized in terms of their economics, based on data acquired by the author from a variety of sources, and supplemented by USBM field data collected by other workers in 1990 and 1991. Numerous mine maps, rock-chip sample assays, and detailed descriptions of mine and prospect sites are in this report and appendixes. Heavy but sporadic mining, mainly between the 1850's and 1950's was nearly all confined to the Patagonia Mountains. High-grade sulfide veins, replacements, and skarn deposits accounted for most of the production, which included large quantities of zinc, lead, copper, and silver, and considerable quantities of gold. Small Quantities of molybdenum, manganese, tungsten, and placer gold have been mined. Most of the traditionally mined metalliferous sites will not see future activity due to the low tonnages present and removal of most high-grade rock. Possible future development areas include copper porphyries and breccia pipes; most are too deeply buried for current development. Localities where similar deposits may be concealed are identified.

Jan 1, 1994

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983

By R. E. Mussier

This investigation was made to study new methods to prepare high-purity yttrium metal, Various methods were used to prepare pure intermediate compounds, primarily chlorides, bromides, and iodides, which were subsequently reduced to metal. The process found most suitable for the preparation of pure anhydrous yttrium chloride involved thermal dehydration of a mixture of hydrated yttrium chloride and ammonium chloride while under vacuum. Yttrium bromide and iodide were prepared most effectively by the direct halogenation of yttrim carbide. Yttrim carbide was obtained by reacting and melting yttrium oxide-carbon mixtures in a carbon-arc furnace. Yttrium halides were purified by vacuum distillation and reduced by alkali or alkaline-earth metals. Lithium and sodium proved to be the best reductants from the standpoint of yield (>95 pct) and purity (>99.8 pct) of the yttrium. The product of the reduction step was sponge metal, which was consolidated readily by conventional cold-mold, arc-melting procedure. The purest yttrium obtained in laboratory scale work was prepared by sodium reduction of yttrium chloride and contained only 125 pp oxygen; other impurities did not exceed 1,000 ppm. In larger scale tests yttrium containing only 800 to 1,000 ppm total impurities was obtained by lithium reduction of yttrium chloride. The tensile properties of high-purity yttrium were determined. Mechanical tests showed that yttrium can be forged, extruded, rolled, spot welded, and deep drawn.

Jan 1, 1963

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing lanthanum (La), praseodymium (Pr), neodymium (Nd), cobalt (Co), copper (Cu), iron (Fe), and magnesium (4g) as possible components of a permanent magnet mate¬rial utilizing a cerium-free synthetic mischmetal (M) as a substitute for scarce samarium (Sm) metal. Magnets containing M-Co-Cu-Mg and M-Co-Cu-Fe-Mg were fabricated by powder metallurgy techniques and evaluated. A synthetic mischmetal (M20) containing 20 pct La, 60 Pr, and 20 Nd yielded the best overall magnetic properties. The M20-Co-Cu-Mg alloys had energy products as high as 13.2 MGOe, remanences as high as 7.89 kG, normal coercivities as high as 6.26 kOe, and intrinsic coercivities as high as 13.4 kOe. The best value of intrinsic coercivity, 22.9 kOe, was obtained with an M-Co-Cu-Mg magnet in which the synthetic misch¬metal contained 30 pct La, 50 Pr, and 20 Nd. These values compare favorably with those of the Sm-Co magnets fabricated and measured at the Bureau's Reno Research Center, which had energy product of 15.1 MGOe, remanence of 7.8 kG, normal coercivity of 7.5 kOe, and intrinsic coercivity of 27.4 kOe. Iron substitution for part of the cobalt resulted in a decrease of magnetic properties, although several percent iron can be added before a drastic loss of magnetic properties occurs.

Jan 1, 1983

By C. Lorimer Colburn

"The diverting of men from industry to combat in the world's war focused the attention of the operators in this country upon mechanical means of doing things. The demand for man-power -was so insistent that every available agency for multiplying it had to be employed. It was during the 1period of the war and immediately thereafter that development of the use of underground loading devices made most rapi4 progress. In all parts of the United States, mining engineers and mine managers were diligent in their efforts to develop mechanical loaders. The mining engineers of the U. S. Bureau of Mines in every section of the country have secured, with the cooperation of the mine operators, data on the actual performance of the mechanical shovels in their districts, and have made them available to the author of this paper.No effort has been made to discuss exhaustively the subject of underground loading devices. It has been the object to collect together in one paper, records of the performance of all machines now in actual use. Improvements in the design of machines are constantly being made the performance records given in this paper relate to operation prior to March 1 1 1921. The records prior to 1920 cay not fully represent the work that could be accomplished with the present models of the same machine.The data secured are given exactly as reported by the mine operators. Since this data were collected there have been two underground loaders, of a different design, put into operation in the iron mines of the Lake Superior District. One is the John Mayne Sub-level loader, being tried by the Cleveland-Cliffs Iron Co., Ishpeming, Mich., and the other is the Cole-Goudie shovel, being tried by the Oliver Mining Company, at Ironwood, Mich. No information has been secured regarding the performance of either of these machines."

Oct 1, 1921