Search Documents

Advances were made during 19b5 in many phases of a broad program designed to increase efficiency in the mining, preparation, and utilization of coal. Also recorded were achievements in activities devoted to mine health and safety, coal resources, and mine explosives. Featured in this report is a review of progress in environmental studies relating to coal mining and utilization. Environmental projects comprise a comprehensive program to facilitate mine reclamation and reduce air and water pollution associated with extraction and use of coal. Publications cited throughout this report present results of the coal program in greater detail. Organizations, institutions, and companies contributing to the program are listed in appendix A. Centers and laboratories conducting the coal research and related investigations appear in appendix B.

Jan 1, 1966

Advances were made during 19b5 in many phases of a broad program designed to increase efficiency in the mining, preparation, and utilization of coal. Also recorded were achievements in activities devoted to mine health and safety, coal resources, and mine explosives. Featured in this report is a review of progress in environmental studies relating to coal mining and utilization. Environmental projects comprise a comprehensive program to facilitate mine reclamation and reduce air and water pollution associated with extraction and use of coal. Publications cited throughout this report present results of the coal program in greater detail. Organizations, institutions, and companies contributing to the program are listed in appendix A. Centers and laboratories conducting the coal research and related investigations appear in appendix B.

Jan 1, 1966

By Joel N. Van Sant

THIS REPORT describes the occurrence, mining, and use of refractory clay in Colorado within Region III of the Federal Bureau of Mines, which includes the States of North arid South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona. Field work by the Bureau of Mines, United States Department of the Interior, included examination of active and abandoned refractory-clay mines as well as a reconnaissance survey and sampling of numerous clay-bearing formations exposed in Colorado. Information from the survey and the sampling will help guide private industry in its search for virgin sources of refractory clay. Library research of published and unpublished reports from various Federal, State, and private sources was conducted during the early phase of the investigation. Most of the refractory clay mined in the Denver-Golden district of Colorado is not used for refractory purposes but is blended with other clays in the manufacture of structural clay products. The predominantly flint-clay de-posits in the Pueblo and Fremont County districts are mined and utilized chiefly in fabricating refractory products.

Jan 1, 1959

By H. W. Busch

In the course of examinations by representatives of the Bureau of Mines of several compressed-air systems in which explosions had occurred, samples were obtained of the carbon deposits that are formed normally in various parts of the systems by decomposition of the compressor lubricating oil. Experimentation with these carbon deposits has demonstrated that they contain a "carbon-oxygen complex" similar to that formed on coal and on other carbonaceous materials and generally recognized as being the cause of spontaneous heating of coal. The exothermic properties exhibited by such a complex are considered significant in relation to the possible initiation of combustion reactions that may lead to explosions or formation of carbon monoxide in compressed-air systems. This report discusses the occurrence of explosions and formation of carbon monoxide in the use of compressed air and presents results of experimentation conducted with carbon deposits from air compressors.

Jan 1, 1949

By Reinhardt Thiessen

Views and conceptions of the origin, composition, and general nature of coal differ so widely that to determine the real extent of actual knowledge is no easy matter. The chemist finds difficulty in attacking the chemical problems and the engineer lacks a broad chemical basis for the study of his problems. Thus the economical and efficient utilization of coal in the industries suffers from a lack of knowledge of the composition of coal itself. Most scientists interested in this matter, as has been brought out in discussions during the recent investigation of coal problems, appear to have only a vague idea of the components of coal and their origin. Some are even in doubt as to whether substances derived from the wood and resins of plants form a part of coal; and few seem to have more than the dimmest idea of what are the components of coal, the condition in which these now exist, and the transformations that they haye undergone. Although during the paiilt century or more many co.rrect observations have been made and recorded, these were falsely or inadequately interpreted, so that many of the interpretations rendered are contradictory. As a result there has been great confusion. Many of the observations made in the past, although accurate and correct, could not be explained, because the principles involved in a correct solution of the problem were not then known. For example, Parkinson, Hutton, Petzhold, Guembel, and others made valuable discoveries regarding the processes by which plant substances are transformed into coal, but as the principles involved are those of colloidal chemistry, a science not known to the scientific world of that time, the observed facts could not be interpreted and the solution of the whole problem was blocked. The explanation of the true meaning of the alternating bright and dull bands so familiar in all ordinary bituminous coals afforCls another example. This banding has been observed and recorded from the earliest times, and has led to the forming of many false theories. Some gAologists, for example, have endeavored to explain the bands as due to alternating climatic conditions during the coal-forming period. Had the geologists known the true nature of coal they could not have made this mistake nor many others made in the past. To fill in a few of these gaps and to clarify some of the existing confusion is the aim of this paper. The immediate cause that led the author to investigate further the composition of coal and the origin and structure of its constituents was that when an attempt was made to discover the meaning of the coking and noncoking properties of coal a more exact knowledge of the nature of coal was required than was then available.

Jan 1, 1920

By Lloyd A. Morley

This seven-chapter document is the first volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. After a short introductory chapter, Chapter 2 discusses the history of electrical use in mining and introduces "typical" mine- power-system arrangements. Chapter 3, 4, and 5 supply basic information on electrical theory, circuit analysis, and motors. Next, the Grounding and Distribution Chapters detail unique aspects of mine power systems. Elements of surface and underground use are included in all these chapters. An index concludes Volume I and is cross-referenced to both report volumes.

Jan 1, 1982

By Richard J. Mainiero

The Bureau of Mines conducted research to evaluate the optimum design for a rock-breaking explosive charge that could be fired unconfined in a gassy or dusty coal mine without the danger of igniting the flammable atmosphere. Charges of various shapes, with and without cavities, were tested in a gallery using 3-by 3-by l-ft concrete blocks as simulated boulders. For these tests the optimum charge, in terms of cost, weight, and convenience in handling, consisted of a flat l-1/2-lb charge of permissible explosive seven-eighths of an inch thick and 7 in in diameter encased in a l/2-in thick layer of fine salt (NaCI). This work demonstrated that it should be possible to produce an inexpensive explosive rock-breaker charge that would be safe to use in underground coal mines.

Jan 1, 1982

By Oliver C. Ralston

The minerals that enter welding-rod coatings and fluxes are the main subject of this report. Few mineral producers know just what minerals and what grades and quantities of minerals are required by the welding trade, and it is for their information that this report has been prepared. The various methods of welding are discussed extensively enough to inform this type of audience. Specialists in welding probably will find little on welding that is of value to them, but they may learn something more about the minerals or mineral products that they use. The authors did not find it easy to prepare this publication, and any needed corrections will be welcomed. Regarding welding, research, Jenks4/ 1 points out that while the process of welding in simple in operation, the phenomena attending its use are extremely complicated, and the efficient and safe use of welding requires an understanding thereof. Although the fluxes and the coatings used have solved many problems, many other problems require the joint effort of the whole industry; therefore, it is hoped that this report will be found of practical value.

Jan 1, 1940

By Douglas F. Scott

Zinc, silver, copper, and tungsten are the principal minerals in Dardanelles RARE II area (No. 4982). Zinc with associated silver and copper occurs in a persistent shear zone in metasedimentary rocks and in a massive sulfide vein; tungsten occurs as disseminated scheelite in a tactite zone along a metasedimentary-intrusive rock contact. Since 1883, approximately 100 lode mining claims have been recorded, mainly it the eastern portion of area No. 4982 (fig. 1). Extensive workings on the Alhambra Prospect indicate past production; however, no records were found for the prospect. At the Alpine Mine, 500 tons of tungsten ore had been mined before 1943 (Hopson, 1943, p. 1) and possibly 1,000 tons of tungsten ore mined by 1947 (Benson, 194/, pp. 2).

Jan 1, 1982

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

By R. A. V. Raff

Although falls of roof, face and rib (or side) of coal mines were the third ranking cause of disabling accidents in 1966, the accidents from these falls resulted in the most serious injuries and accounted for approximately 50 percent of the total fatalities (I). Further breakdown of these statistics shows that 88 percent of the fatal accidents occurred within 100 feet of the working face and that 96 percent of the deaths were in bituminous mines, with only four percent taking place in anthracite workings. These figures demonstrated the need for improved reinforcement procedures in operational coal mines, and they provided ample justification for research in the area of accident prevention. The purpose of this project was to investigate the use of polymers and of related techniques to achieve rock bonding and reinforcement of coal mine structures, in order to obtain better or permanent ground support (e.g., drifts, entrees, coal and ore passes, galleries, tunnels and shafts) by the fill ing of fissures in the rock, thereby preventing or delaying the onset of serious rock degradation processes.

Jan 1, 1973

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By T. H. Jeffers

The U.S. Bureau of Mines has developed porous beads containing immobilized biological materials for removing metal contaminants from waste waters. The beads, designated as BID-FIX beads, are prepared by blending biomass, such as sphagnum peat moss or algae, into a polymer solution and spraying the mixture into water. Laboratory studies were conducted to determine bead sorption and elution characteristics. Batch and continuous tests demonstrated that BIO-FIX beads sorbed arsenic, cadmium, lead, and other toxic metals from acid mine drainage waters collected from several sites. Selectivity for heavy and toxic metal ions over calcium and magnesium was demonstrated. The beads exhibited excellent metal sorption and handling characteristics in stirred tanks, column contactors, and a low-maintenance passive system. The sorption process was reversible, and metal ions were eluted from the beads using dilute mineral acids. Cyclic tests indicated that the beads continued to extract metal ions after repeated loading-elution cycles.

Jan 1, 1991

By Philip E. Niebuhr

A procedure, which can be performed in the field by nonanalytical personnel, is given for sensitive spot tests for detecting tellurium or selenium. The expressed need of a field test for detecting small amounts of tellurium, which may be accompanied by relatively large amounts of selenium, has led to the development of this method. Tellurium search has been impeded by the lack of a satisfactory test from the standpoint of sensitivity and specificity. A quantitative laboratory method exists, but it is expensive and relatively laborious. Several other qualitative tests are known, but they require unstable solutions, which must be freshly prepared for use, and a greater variety of laboratory equipment. The particular advantages of the test described are its simplicity and the stability of the reagents required, there-fore is is well adapted for field use. Also, this test was found to be of practical use in the analytical laboratory when screening samples, thereby reducing analytical costs. The roughly quantitative interpretation of the results can save time by indicating the approximate size of the sample taken for a quantitative determination.

Jan 1, 1962

A symposium was held on January 30 and 31, 1973, at Pittsburgh, Pa., to review the state-of-the-art in designing and utilizing diesel-powered equipment in underground mining. The Health and Safety Activity of the Bureau of Mines sponsored the symposium with major assistance from the following four participating organizations: The American Mining Congress J. Allen Overton, President The United Mine Workers of America Arnold R. Miller, President The National Independent Coal Operator's Association Cloyd D. McDowell, President The Bituminous Coal Operators' Association, Inc. Guy Farmer, President Seventeen papers were presented during four half-day sessions devoted to the general subjects of the diesel engine, the place of the diesel in underground mining, health protection using diesels underground, and maintaining safety of diesels underground. Eleven of the speakers were from industrial organizations here and abroad; one represented the Provincial Government of Nova Scotia; two were with the Department of Health, Education, and Welfare; and three reported on Bureau of Mines work related to diesels.

Jan 1, 1975

By Thomas M. Sweeney

This open-file map is a quick reference containing location, ownership, and general lithology information on 124 active or significant Nevada gold mines. The map includes all counties, significant towns, and major highways in Nevada to aid in mine location. Several geologic trends with which the mines are associated are also depicted. General ore genesis for each deposit, including sedimentary, volcanic, plutonic, and placer-hosted deposits, are also identified. Gold mines are also listed alphabetically, by mine name, on the map. Each entry includes the appropriate county, percent of company ownership, operating company, and the property status as of May 1992. For additional information, contact Thomas M. Sweeney, U.S. Bureau of Mines, Western Field Operations Center, 360 East Third Avenue, Spokane, WA 99202; telephone (509) 353-2700.

Jan 1, 1993

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are investigating technology and methods to monitor the blind areas around large haulage equipment used in surface mines. On average, six fatalities a year can be attributed to equipment colliding with other vehicles or pedestrian workers, or backing over the edge of a dump point. Several off-the-shelf technologies exist for monitoring areas that an equipment operator cannot see from the cab, including radar, video cameras, and radio signal detection systems. NIOSH researchers have tested many of these systems on large dump trucks both at their test facility and at surface mines. This article discusses the technologies available for this application and their effectiveness in detecting objects near an off-highway dump truck. Also, guidance is presented for mine safety personnel who are planning to evaluate collision warning systems or cameras on their haulage equipment. Available Technology Over the past few years, the number and types of systems available for monitoring the blind areas around heavy equipment have increased. Systems marketed for the automotive and recreational vehicle industries have been around for a while. Small video cameras can be found

By Allen McComas, Frank Chase, Phyllip Worley

Longwall mining has gained the reputation as being the safest extraction method in underground coal mines. However, one of the most difficult tasks associated with longwall mining is moving the face once a panel is completed. Based on Mine Safety and Health Administration (MSHA) fatality reports since 1996, longwall face recovery operations have claimed the lives of 5 U.S. miners and have resulted in numerous injuries. Recovery operations can be hazardous because they involve moving large pieces of equipment in very confined spaces. They are also conducted in highly stressed ground conditions due to front abutment loads generated by panel extraction. Shield removal is the most hazardous operation during face recovery because miners are constantly exposed to the unpredictable gob edge. To protect the miners, one or more walking shields, cribbing and/or other supplemental roof and standing supports are typically employed as breaker line supports as each shield is removed. At the Harris No. 1 Mine in southern WV, mobile roof supports (MRS’s) have been used in lieu of traditional walking shields on 17 face moves since 1997. MRS’s are shield-like support units mounted on crawler tracks and are commonly used during room-and-pillar retreat mining operations. For longwall recovery, the two biggest advantages that MRS’s have over traditional walking shields are that they are remotely controlled and are highly maneuverable. MRS’s have contributed to safer shield recovery and shorter move times at the Harris No. 1 Mine. This paper will address both the safety and the operational issues associated with MRS usage during shield recovery. It will also discuss new developments, including the use of the inherently safer battery powered MRS’s, which have been recently certified by the Mine Safety and Health Administration.

8053. Andreev, B. A. Zakashanakii, M. S., Samsonov, N. N., and Fotiadi, E. E. A Textbook of Gravitational -Surveying, (in Russian). Gosgeolizdat, Moscow-Leningrad, 1941, 432 pp. This textbook was written at the suggestion of-the faculty of geophysical exploration of the Leningrad Mining Institute. It contains two parts: (1) Theory and technique, and (2) Applications to geology and exploration. The features bringing; the text up-to-date include: (a) Description of the principal modern gravimeters; particular attention to the method of simultaneous oscillation of 4 pendulums; (b) discussion of the aperiodic oscillation of torsion balances; outline of the construction of variometers Z -20 and Z-40; (c) material for aid in interpretation, such as reference-charts, formulas with their derivation, atlas of theoretical curves, and examples of interpretative calculations; (d) considerations in the planning of surveys and the densities of various rocks; and (e) detailed analysis of significant examples. The text is provided with a bibliography, V. S.

Jan 1, 1946