Search Documents

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nomnetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By Kenneth Trelewicz

This report describes the total effort that went into developing environmental test criteria for general mine instrumentation. The project was a two-phase effort. Phase I consisted of research and mine visits to develop an environmental profile for mine instrumentation. The profile was translated into general requirements and then into test requirements. A review of existing government and commercial specifications was performed to determine if they matched mine instrumentation test requirements. Finally, a set of environmental test procedures was developed for the testing of mine instrumentation. Phase II consisted of selecting and purchasing sample mine instrumentation and subjecting them to the previously developed tests. The purpose was twofold: (1) to evaluate the criteria developed for use as an instrumentation test document and (2) to determine the effects of the various criteria on a representative sample of both proven and newly developed instrumentation. The test criteria were then modified, based on the results of the testing, and are listed therein.

Jan 1, 1981

By J. A. HUFF, V. V. BAKER

This circular is intended to present in brief form the statutory provisions of Pennsylvania regarding mining operations, in force at the end of the 1931 session of the legislature. lo reference is made to general laws which affect mining only incidentally in common with other subjects, such as the workmens compensation law. The statements have been condensed as far as practicable, and provisions not deemed of general interest, such as matters dealing only with administrative details, have been omitted. This circular obviously is not written with such particularity as to be of great value to the legal profession, but it is hoped that it will be beneficial to the mining industry in giving this information in a relatively compact form. At the end of each paragraph the statute from which it is derived is cited to facilitate reference to the text of the law. It is planned to publish additional circulars from time to time dealing with the mining laws of other States. Any criticisms of the form of publica- tion followed herein, or suggestions aimed at the improvement of future circulars, will be welcomed.

Nov 1, 1932

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981

By B. J. Moore

This publication contains analyses and related source data for 310 natural gas samples from wells and pipelines in 16 States. All of the samples were obtained and analyzed during calendar year 1978 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis appara¬tus, which are described in Bureau of Mines Bulletins 4862/ and 576.3/ The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Twenty previous publications have presented the results of 11,573 gas analyses made prior to 197R. The first three, Bulletins 486,4/ 576,5/ and 617,6/ contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 17

Jan 1, 1979

By Anu Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Miner Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the NIOSH Bruceton Experimental Mine was pressurized using a 1.1 m (42 in) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By Kim B. Shedd

The U.S. Bureau of Mines Particulate Mineralogy Unit examined the habits of six zeolite minerals commonly occurring in domestic zeolite deposits. Mineral habit is of interest because current theory on the potential for sarcoma production in test animals emphasizes the size and shape of mineral particles, without regard to composition or structure. A scanning electron microscopic study revealed that, of these six minerals, only mordenite and erionite crystallized in acicular to fibrous habits, The fibrous varieties of these two minerals were characterized by size and shape on the transmission electron microscope, and their dimensions were compared with those of asbestos and amphibole cleavage fragments. When comminuted, these two minerals possess "fibrosity indices" similar to those of amphibole cleavage fragments. One sample, a rare woolly erionite, has uniform widths, large aspect ratios, and a "fibrosity index" similar to those of asbestos.

Jan 1, 1982

By E. R. Spencer, E. Reeves

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

By G. B. Clark

One portion of this project was to test a blast shield and to design some features for a novel tunneling method termed the Automated Drill and Blast System (ADBS). The ADBS tunneling concept was developed for the design of an excavation system of greater efficiency than conventional drill, blast, and muck (DBM) systems by minimizing the down time and approaching the non-cyclic efficiency of continuous tunneling by means of small charge blasting. Small charge blasting uses simultaneously detonated, small light charges (less than 200 grams per hole) in four to eight shallow (24 to 36 in. deep) holes usually in a line. Limitation of the total explosive per blast reduced air blast overpressure, fly rock velocity, vibration, and noise. Thus, shielded equipment can remain at the face and a tunnel shield permits support personnel to work outby the shield at all times. The ADBS equipment will be composed of five components: (1) a chassis, upon which is mounted automated mucking equipment, and a frame which carries (2) the hydraulic drill(s), (3) load/blast system(s), and (4) control cab(s). The blast shield may have its own mounting. Ventilation, horizontal, and vertical alignment controls are incorporated in the system. The blast sheild, which protects personnel outby the advance equipment from air blast overpressure, fly rock, and gases, was tested with full scale small charge blasting. A blast shield was designed, fabricated, and tested under conditions anticipated for a working model. The shield was designed to expand to fit the tunnel shape, to seal itself to the tunnel periphery, and to contain air blast, fly rock, and gaseous explosion products. In addition, the shield, which was lined on the inby side with rubber belting, reduced the blast noise level outby the shield to 113 dBA or less, which is very near permissible levels. The test results show conclusively that the shield concept is viable. Based partially on the shield tests, a blast resistant control cab was designed to be located on the equipment chassis inby the blast shield to protect operators during blasting, and to contain all the controls necessary for system operation and safety. The economics of tunnel driving using the ADBS were compared with those of DBM. Four rock types, which determine advance rate, and four cost categories were examined. The results of this analysis are as follows: 1. ADBS advance rate is faster because equipment remains at the face and operation procedes semi-continuously. 2. ADBS bit and explosive cost (which accounts for 4%o of the total advance cost) is higher than for DBM. 3. ADBS equipment cost, on a per foot basis, is lower than for DBM. 4. Due to a reduced labor force, ADBS labor cost is lower than for DBM. 5. Because of the overbreak reduction due to controlled blasting, ADBS tunnel support cost is lower than for DBM. 6. On a per foot basis, total ADBS advance cost is from 17% to 20% lower than for DBM, depending on tunnel diameter and rock type. The small charge method greatly reduces ground vibration, increases personnel safety by limiting excessive fracture, and decreases tunnel support requirements by reducing overbreak. The overall analysis, tests, and results to date show that the Automated Drill and Blast System may be developed into a viable tunnel excavation method. The method also may be adapted to use in the mining of ore. For some types of mining operations, the cyclic nature of conventional drill and blast methods may not be a disadvantage, either where the drilling and mucking may proceed simultaneously or where the operations are carried out in adjacent working faces. The proposed method would find application where continuous methods of excavation are desirable.

Jan 1, 1979

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By J. L. Holman

The Federal Bureau of Mines has conducted research to delineate factors affecting relative fabricability of electrowon and electrorefined copper. The Bureau's Rolla Metallurgy Research Center coordinated and participated in a statistical round-robin chemical analysis and performed impact tests on lead-doped copper specimens. In a series of round-robin analyses, cathode, bar, or rod from a domestic lot of electrorefined copper and electrowon copper from a domestic and a Peruvian source were analyzed for Pb, Fe, Bi, Se, Ag, O, S, Sb, and seven other elements. The electrowon cathode from both sources surpassed requirements for electrolytic cathode, although lead in the Peruvian lot exceeded specification for oxygen-free electronic grade. The least interlaboratory agreement was for oxygen analysis, Copper specimens, doped with up to ~300 ppm Pb and consisting of as-cast material (fine-grained or coarse-grained) and hot-rolled material, were impact-tested at temperatures to 871° C (1,600° F). Impact energy of fine-grained material dropped 26 pct with increased Pb up to 20 ppm and more gradually thereafter. Coarse-grained specimens fractured at lower energy with little dependence on lead. Hot rolling raised impact energy substantially. Grain structure is evidently as significant as lead in influencing workability. Some discussion is given of possible effects of oxygen, sulfur, and porosity.

Jan 1, 1978

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

By S. L. Crouch

An important class of mining problems involves excavations in planar seam or vein-type deposits. In many instances it can be assumed that the seam is at 'infinite' depth in a homogeneous, isotropic or transversely isotropic, linearly elastic rock mss, and that the normal to the plane of the seam is a principal stress direction. Rational planning of excavations in such deposits requires a knowledge; of the stresses and displacements induced by complicated, irregular excavation geometries in the plane of the seam. This problem previously has been solved either numerically or by means of an electrical resistance network analog. Both of these methods effectively simulate the mined portions of the seam as a dislocation in an otherwise continuous mass, and determine the complete solution in terms of the stresses and displacements at the seam. In both cases, the plane of the seam is divided into a number - say, M x N - of squares, and the solution to the problem is determined in terms of the solution to an M x N system of equations. The numerical approach requires that these equations be solved explicitly, while the analog; solves them instantaneously with current analogous to stress and voltage to displacement. A purely numerical solution of practical problems can require a substantial amount of computer time, particularly in situations that demand some sort of sequential analysis, either due to successive mining or to nonlinear behavior of the seam material. This report describes a combined analog-digital computer system for solving problems that are impractical when either device is used separately. The digital computer and the analog are interfaced so that the digital computer can receive information from the analog via a switching matrix and an analog to digital converter, and can activate points of the analog via another switching matrix and a set of digital to analog converters. The resulting hybrid system can be used to simulate arbitrary "stress-strain" characteristics for any portion of the seam by an iterative procedure similar to the initial strain method used in nonlinear finite element analysis. Thus, the hybrid system combines the speed of analog computation with the decision-making capability of the digital computer: the analog instantaneously solves the set of equations, and the digital computer decides how the initial strains must be altered for the solution to be compatible with the prescribed "stress-strain" characteristics for the seam material. The hybrid computer system has many implications for rational planning of underground excavations, since it allows practically any type of inelastic seam behavior or artificial support characteristics to be simulated. Inelastic seam behavior, for example, might be due to either rock failure or to time-dependent deformation.

Jan 1, 1974

By David D. Rabb

A report on location, sampling, assays, mineral examination, amenability leach tests, and evaluation of certain mine dumps in Mohave County, Arizona. Extractions of greater than 30 percent of the gold and silver were achieved during simulated heap leaching of selected mine dump material. Consumption of reagents was relatively low and results suggest leaching of prepared heaps is technically viable and could be economically attractive.

Jan 1, 1980

By L. C. IlsLey

Many accidents rightly classifiable as electrically caused are not so classified for the reason that in numerous accidents the part that electricity played in causing the fatality is only suspected. For instance, a workman might receive a shock that would cause him to lose his balance and fall beneath a trip of cars; if no one saw the first part of the accident, the cause undoubtedly would be charged to "haulage." This paper covers a brief study of fatal and nonfatal electrical accidents. The first usually result from direct contact with the electrical circuit or electrical apparatus; the second more often are the result of arcing or flashing due to handling defective apparatus or making repairs on "live" equipment or circuits. It is hoped that helpful suggestions may be offered for minimizing accidents of these two classes.

Jan 1, 1938

By Joseph M. Kurtak

The Bureau of Mines is currently conducting a four year mineral assessment of the 5.7 million acre Valdez Creek Mining District in Southcentral Alaska, as part of its ongoing statewide mining district evaluation program. This report is a summary of the 1987 field work, which included the examination of mines, prospects, and mineral occurrences in the study area. Placer gold has been the most important metal produced in the area, and production totaled 161,131 oz, with the majority of the production coming from the Valdez Creek Mine. Lode gold and silver production totaled 1,581 oz and 8,617 oz, respectively and came mainly from the Golden Zone Mine. Varying amounts of other metals, including copper, lead, zinc, molybdenum, antimony, chrome, nickel, cobalt, tin, tungsten and platinum exist in the study area. Occurrences of industrial limestone and coal are also located in the area.

Jan 1, 2011

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975