Search Documents

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling.

Feb 1, 2020

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By William R. Adamson

This paper describes some of the results of previously unpublished research studies conducted in underground operations in Chile and Australia, where cross-hole seismic measurement profiles were interpreted in terms of dynamic modulus. This work dates from a period between 1987 and 1990 and the Author suggests that 30 years on, applying modern day technology, instrumentation and modelling methods, more meaningful, practical and applicable results may be obtained.

Feb 1, 2020

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

By Roger Favreau, Patrice Favreau

Without blasting there can be no roads, no hospitals, no factories, not even foundations for homes. Yet in 1960 the only way to design a blast was by trial/error. By comparison, bridges were already designed by calculations before being actually built. This was possible because equations based on the fundamental principles of science existed with which all the stresses in the bridge could be calculated. In 1960 no equations based on the fundamental principles of science existed with which the mechanisms that take place inside the rock mass during a blast could be calculated. Since then the main author made it the objective of his research to seek such equations, and to validate that they gave accurate answers by means of experiments in the field, experiments made in co-operation with mines, quarries and the explosives industry; results have been reported in some 90 publications.These equations now deal with essentially all aspects of a bench blast: the intensity of the shock wave and the fragmentation size distribution throughout the rock mass; the movement of all the fragments into the muck pile; the fly rock and vibrations from the blast; etc.; are presented examples of such equations. They are now assembled into a computer simulator called Blaspa accessible on the Web, with which one can design a blast just as a bridge is designed. An example is presented. The reason to design a blast by simulations rather than solely by trial/error is that if it leads to damage, it is only after the actual blast that the blast design is realized to cause damage. If however the blast design had been simulated before the blast, then the risk of damage is identified before the blast and is prevented by redesigning the blast. Examples of such situations are presented. The need to a void damage is very necessary because the public is becoming opposed to blasting. When a blast does cause damage, and people learn that the blast was designed solely by trial/error even though simulation was available and would have prevented damage, they become even more strongly against blasting; they may succeed in getting a quarry closed. Their objections to unchecked blasting are not unreasonable, especially as simulating a blast with Blaspa on the Web is a very simple procedure.

Jan 1, 2013

By M Sampara, W Comeau

The introduction of large-diameter holes to underground mining has made possible the development of new mining methods such as the Vertical Crater Retreat (V.C.R.) method. It is not only the safest underground excavation system but also provides mass production at a lower cost than any conventional mining method (1, 2, 3, 4, 5).

Jan 1, 1981

By Jack Eloranta

This paper compares energy requirements for blasting, crushing and grinding. By tracking electrical consumption for various powder factors, a general trend has appeared. This study involves over 100 million tons of ore and powder factors ranging from .5 lbs/LT to .8 lbs/LT. Actual energy usage is compared to predicted energy based on the Bond equation.

Jan 1, 1997

By Rolf Koenig

After the Dynatronic firing system was demonstrated for the first time at the SEE conference in Miami in 1987, it was officially approved in Germany at the beginning of 1993. Dynatronic has now been on the market for 5 years. At present, it is used in several European countries and successful test series have been running in Australia.

Jan 1, 1998

By Johan Finsteen Gjødvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad. This has been done by use of an online survey through the most of 2018. Questions have been raised on vibration monitoring during blasting. The existence of norms, guidelines or standards and how they are used. Even though the questions have been kept at a high level they are formed to try to map the different national standards use of such things as frequency, guidance on monitoring position, distinction between different types of structures, requirement to the equipment and more. Furthermore a few initial questions have been raised on other environmental monitoring relevant for blasting. The respondents are national, cooperate or individual members of EFEE. The answers are experts in the use of explosives and vibration-monitoring in their respective countries. More than 60 have answered the questionnaire from 29 different countries. Mainly European as well as other nations including India, Israel, Nigeria, Saudi Arabia, UAE, USA, Greenland and Hong Kong. By analysing the incoming answers, the differences and similarities in vibration monitoring of the respondents has been clarified and mapped. Where possible other environmental monitoring has also been analysed. Where needed the different guidelines, standards and regulations have been visited to verify the answers and further elaborate on the comparison.

By Johan Finsteen Gjodvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad.

Feb 1, 2020

By Milos J. Bila

I would like to discuss today several safety topics that we at Nobel feel are going to be particularly critical to all of us who are involved in the manufacturing, transportation, storage and use of commercial explosives during the '90s. My purpose is to identify these topics in order to allow those in the commercial explosives community to better understand the potential difficulties we face.

Jan 1, 1992

By Jose A. Sanchidrián, Ricardo Castedo, Pablo Segarra, Juan Navarro

A study conducted at a mine site that used traditional field surveying and physical hole spot markings bench marked their combined drill and blast performance. The analysis of the operational expenditure (OPEX) improvement determined there were many measurable cost improvements. A primary factor that most operations have to deal with is over drilling of holes. This alone impacts the cost due to nonproductive labor allocations, excessive explosive costs, increased drill tool costs, increased drilling costs and has an impact on the downstream operation cost such as digging the shot material. Other related investigations also show a downstream impact of poor fragmentation on digging payload tonnes, cycle times, haulage payload tonnes, time to load a truck and the number of passes to load the tuck. The intent of this presentation is to draw attention to aspects of mining we understand but may be missing the big picture effects, such as the ability to reduce the operational expenditures consistently to impact the bottom line. The target audience is across the board from owner operators, drill and blast contractors to blasting contractors. Everyone can benefit from these improvements.

Jan 1, 2019

By Lina Lopez, Jose Sanchidrian, Manuel Lopez, Pablo Segarra

Previous work in which rock properties and blasting parameters (geometry, charging and timing) were reported together with truck filling times, is taken as a starting point for a thorough analysis of the influence of the former on the mucking velocity. The experimental set was composed by 11 blasts made in an open pit mine. Non-parametric, distribution-free statistics is applied. The mucking rates (in bank cubic meters per unit of bucket volume and per hour) appear to be clearly dependent on the explosive energy and powder factor, both magnitudes combined as energetic powder factor (energy per unit of rock volume). The mucking rate is a non-monotonic function of such factor in the range of the blasts analyzed. The determination of the function is optimum when the fraction of the explosive below grade is not considered and when the explosive energy is qualified as that delivered at a partial detonation regime. Different types of loaders seem appropriate for different energy levels. At low levels both front loaders and rope shovels obtain small productivities without a statistically significant difference in their performance. At high energy levels, front loaders qualify higher than rope shovels. Mucking velocities can be equally small at low energy powder factors and at high ones if rope shovels are involved.

Jan 1, 2008

Computational techniques in determining particle size distributions after blasting is getting wide acceptance. A well known approach to extract this kind of information from digital images is edge detection. The number of edge points on a given image increase proportional to the increase of the particles on the image. By selecting a conveniently smooth threshold, counting the signed edge pixels may be a suitable metric further used to quantify the number of particles in the image. Here we propose an image processing algorithm together with Adaptive Neuro Fuzzy Inference System (ANFIS) to efficiently count the rock particles with various sizes on a given surface. To determine a suitable approximation for a mapping between the number of edge pixels and the number of particles, ANFIS is a suitable tool. As a trainable classifier ANFIS proved itself as being better efficient approach than other well known multilayer perceptron classifiers. ANFIS is trained by using convenient training data pairs previously experienced from empirically counted sample images. When given a new image containing the particle information of selected surface, the hybrid neuro fuzzy image processing approach provides satisfying performance on counting the correct number of particles up to the given scale of sizes. In this paper an experimantal study for assessment of particle size using ANFIS is presented.

Jan 1, 2004

By Josephine Bones, Robb Larson, Daniel Miler

Avalanches are commonly mitigated through the use of explosives at ski resorts and above transportation corridors. Surprisingly, very little research has been conducted on snowpack response to explosive inputs, and efforts to model this response have been limited. The purpose of this ongoing research project is to ascertain an understanding of the dynamic snowpack response in relation to explosive size and height above the snowpack, coupled with snow conditions, to enhance avalanche control. A system of sensors and computer-controlled data acquisition components has been created to record the movement of snow resulting from the charge detonation. The system records acceleration vertically and radially within the snowpack at two distances from the point of detonation as well as blast air pressure at one location during explosive events. The data at two locations allows inferences to be made about the transmittance and attenuation of shock waves through the snowpack radially as well as vertically. The data shows that raising charges above the surface results in increased snowpack dynamic response when compared to surface detonations. Applying power function regression to accelerations for individual charge elevations, it was determined that both radial and vertical rates of attenuation were not dependant on charge elevation. Additionally, raising the charge also resulted in increased dynamic response at depth within the snowpack

Jan 1, 2012

By J S. Kuszmaul

"A computational model of rock blasting is being developed to examine the blasting problems associated with in situ oil shale processing. This model, however, will also be useful as a design tool for the traditional problems in rock blasting. The model includes fundamental treatment of both shock-wave propagation and the accumulation of brittle fracture in the rock. As a result, the model accurately predicts the degree and extent of fracturing as functions of design parameters. The model has proven useful for making parametric studies and for evaluation of alternate blast designs. This paper demonstrates the use of the numerical model to simulate the fracturing induced by the detonation of a vertical explosive column near a bench. The fracturing induced by three differentexplosives indicate that (in the chosen geometry) the most efficient breakage is done by a column of ammonium nitrate and fuel oil mixture (ANFO) used with a toe charge of aluminized ANFO. There was too much unfractured rock left when ANFO was used alone; aluminized ANFO used for the entire explosive column caused excessive fracturing. A final case involves ANFO used alone to fracture a different rock type. This case points out that in a different rock type, the ANFO will not leave excessive unfractured rock."

Jan 1, 1987

By Joseph A. Meyers

NYC has always been a high-profile target for both foreign and domestic terrorists. Explosives have always been the go-to tool for terrorists to bring about serious physical injury, death, and property damage in our society. Today with the anti-police movement gaining traction in the United States and anarchists groups using homemade explosives against law enforcement and municipalities, it is the responsibility of the explosives industry to ensure that every explosive product on a blasting site is secure. We must prevent the theft of these energetic materials used on projects and sold by vendors so they are not used by these terrorists. We have learned many lessons here in NYC which began with the theft of explosives used for blasting projects in NYC to supply the IRA (Irish Republican Army) 50 years ago. The liability is too significant to take short cuts in securing energetic materials. Over the years through cooperation with all agencies and the industry we in NYC have developed certain proven protocol and procedures we would like to share with the industry. An efficient and effective security plan for the logistic movement of explosives, as well as for the blast site is imperative to keeping the good name of the industry from negative repercussions and possible additional bureaucratic oversight of an industry that is highly regulated and still recovering from the pandemic. Communication, security assessments and transparency with all stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the overall security for the blasting project. This SOP (standard operating procedure) will allow the AHJ to become a proactive partner in the security of the blasting project. If the AHJ is not a law enforcement agency, the law enforcement agency specialty unit must be notified and included in all phases of the project. The security for a blasting project with AHJ and law enforcement input starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. This includes threat assessments on new and existing structures. SME’s (Subject Matter Experts) must be present at all stages. The blasting industry and regulators must work collaboratively to improve safety, security, and create a dialogue with law enforcement and the AHJ. Relationships are built through trust, teamwork, transparency, and communication and greatly improve the safety of our great country.

Jan 21, 2025

By Robert Hopler

CHAPTER I. DEFINITIONS AND CLASSIFICATIONS. Definition of Explosives. SECTION 1. The term “Explosive” or “Explosives” whenever used in this ordinance, shall be held to mean and include any chemical compound or mechanical mixture that contains any oxidizing and combustible units, or other ingredients, in such proportions, quantities or packing that an ignition by fire, by friction, by concussion, by percussion or by detonator of any part of the compound or mixture may cause such a sudden generation of highly heated gases that the resultant gaseous pressures are capable of producing destructive effects on contiguous objects or of destroying life or limb, and includes all the articles specifically mentioned in Section 3 herein, and all other similar articles

Jan 1, 2013

By Joshua Hoffman

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. Student chapters help with this effort but what are they doing and are there things they could learn from each other? This paper discusses the University of Kentucky Student Chapter's efforts to grow membership, retain its recruits, and integrate them into the explosives industry. Several social and professional events during which the students are able to meet and network with members of their future industry are introduced. The special relationship that has been fostered between the University of Kentucky and Missouri University of Science and Technology is discussed. Professional development initiatives which are critical for a student to become vested in the industry are shared in this paper. These opportunities which range from internships to research positions allow a person to get a better understanding of the explosives industry and find the niche that best suits them. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements there is a trend of job placement primarily in the engineering industry. By providing these students with the chance to learn more about the explosives industry and get hands on experience more of these future engineers and professionals can be retained after their graduation.

Jan 1, 2013

By David Yanez

The hydroelectric project "El Cajón" is currently under construction in the state of Nayarit, on the Santiago River, in western Mexico. This project is comprised of a Concrete Face Rockfill Dam (CFRD) with a rockfill necessity of 10,5 million cubic meters and it reaches a height of 188 m. The generation equipment includes two turbines with a total installed capacity of 750 MW.

Jan 1, 2006