Search Documents

By A. Vishwakarma, V. Himanshu, K. Dey

Underground mining is the most feasible method after extinction of shallow depth ore deposits. Longhole stoping method is the most technically advanced method for the faster excavation. In this method, the holes are drilled in the form of ring pattern and explosives are used for the rock breakage. During blasting, the explosive energy sometimes also breaks the non-ore material. The non-ore material gets included in the extracted ore and enhances the ore dilution. Few uncontrollable factors which affects the ore dilution are ore body characteristics, rock quality, insitu stress condition etc. Apart from uncontrollable factors, explosive energy and blast design also plays an immense role in ore dilution. In the blasting practice, the purpose is to effectively utilise the explosive energy for rock breakage. The optimum delay is required so that the blast holes attain adequate free face before the blasting. This paper deals with the optimisation of blast design parameters to reduce ore dilution in underground hard rock mining having narrow vein. The study was carried out using numerical simulation. The explicit dynamics based modeller of Ansys was used for this purpose. The parametric variations in the models were done to optimise the parameters. The burden has been optimised first by varying the width of the narrow vein. The blasts of a ring consisting of single hole were conducted in the model by varying the width of the narrow vein. The damage contour under different parametric variations were analysed. The experimental trial has been also carried out at Zawar Group of Mine, Rajasthan, India. The optimum parameter was decided based on the result of experimental trial and numerical simulation model. The output of the model shows that optimum burden for 3.5 m narrow vein width is 1.12 m and for 1.0 m, it is 1.54 m. This shows that the optimised burden is higher in the vein having lesser width as compared to the greater width. The presence of joints/changed media/interface (between the sidewall and narrow vein) is the major reason behind this. The wave gets reflected back very fast on coming in contact with joints in a 1.0 m narrow vein as compared to a 4.0 m narrow vein. This will quickly convert the compressive wave into tensile wave giving rise to tensile slabbing. Hence proper utilisation of explosive energy will take place for the breakage of rock mass when the width of the narrow vein is smaller. The burden obtained from the experimental trial and numerical simulation models is less than 2.0 %. Hence the numerical simulation based approach can be used for the assessment of the optimum burden for ring blasting in narrow vein under different geomining conditions. This helped in reducing ore dilution and maximization of ore recovery. In the future, empirical relationships may be developed by considering different geological discontinuity, the strength of the rock mass and explosive parameters.

Jan 1, 2024

By David S. Shatzer, Michael R. Purcell

Current world events have demonstrated the use of commercial vehicles, other unconventional modes of transportation and unusual materials as explosives or incendiary weapons, affecting commerce, disrupting cities and even entire societies. Since the implementation of the Organized Crime Control act of 1970 the Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) has been investigating and studying explosives and incendiary devices and their related effects.

Jan 1, 2004

By Corry Goumans, Ron J. Elliot

This paper discusses the challenges encountered in drilling and blasting of a small diameter shaft underneath a parking garage in historic Gastown, Vancouver, BC. This project involved drilling in a restricted headroom area, blasting in a confined space environment, and excavating using a novel vacuum technique. The 1.2m x 1.2 m x 8.5m deep shaft was required for installation of a hydraulic piston for a show lift. The project called for very accurate drilling through inter-bedded sandstone and siltstone within the water table. Development of a unique blast design was required for blast vibration control on a historic structure located just 15.8 meters away. The shaft was successfully completed without damage to any of the surrounding structures.

Jan 1, 2004

By N. Rouse

Underground raises and slots are a vital part of underground blasting operations. Raises and slots are vertical shafts or openings used for ventilation, ore passes, or creating voids in stopes. In the author’s experience, raise and slot designs can vary significantly from operation to operation or even within a single operation, sometimes for reasons unknown. The results of the various designs can differ depending on drilling accuracy, geology, and the explosives used in the design. The purpose of this paper is to summarize the recommendations found in published literature on raise and slot design in one document, while incorporating some of the author’s own experience with optimizing raise and slot designs in underground operations. Some inspiration is also included from burn round designs; small versions of raises drilled horizontally in development blasting rounds. This document includes discussion points on drillhole diameter and depth, pattern design and relief requirements, explosive types and loading recommendations, and timing. Ultimately, this document can be useful to those looking to design a raise or slot blast for the first time or for those looking to improve on the results from the raise and slot blasts used at their operations.

Jan 1, 2024

By CVB Cunningham

"The Kuz-Ram model as originally proposed included an error in assuming that the mean fragmentsize predicted by Kuznetsov’s equation was actually the 50% passing size. In 2003 Spathis began discussions on this issue and recommended correcting the equation. The correction produced more fines in the predicted fragmentation, which had been a criticism of some users of the original model. Ouchterlony subsequently showed that the error had, if anything been beneficial, and that the Swebrec function adequately covered the fines. This author shows that the Spathis correction does not assist the fines correction in examples examined, but tends to underestimate coarser fractions. An intrinsic problem of communication between academics and engineers is a root of misunderstanding on both sides, and requires patience by both parties to enable value to arise."

Jan 1, 2016

By Ambrose Buchanan, Rob Farnfield, Charles Adcock

Beginning on 7th September 1940 the City of London was subjected to 57 consecutive days of bombing in what became known as the ‘London Blitz’. To commemorate the 70th anniversary of this event a television series was commissioned that required the open detonation of World War 2 equivalent bombs close to purpose built structures constructed using period design and materials. The structures were built on a remote test facility in the North of England that is able to fire large quantities of explosive in the air.

Jan 1, 2011

By M R. Hettigner, J Nawrocki, C E. Johnson, P G. Cahill

This study evaluates the effects of both short inter-hole and intra-hole delay times on rock fragmentation and throw. Full-scale test blasts were analyzed at a granite quarry in Talbotton, GA. This analysis provides a representative understanding of timing effects on fragmentation in the field, different from previous lab scale studies that negate the effect of geology. Inter-hole delay times between 0 ms and 25 ms were tested on a series of 4 bench blasts and subsequently examined using photographic fragmentation analysis methods.

Jan 1, 2017

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Serdar Celik, Yucel Karakus

This paper presents bench blasting designs based on results of vibrations analysis on test shots organized in an open pit coal mine located near to Soma district at Manisa province in Turkey. There are some structures which can be adversely affected by blasting at the coal mine. The one of the main goals of this study is to perform a preliminary assessment of possible damage effect of ground vibrations induced by blasting at these structures by risk analysis based on ground vibration measurements. During this investigation, the data pairs of scaled distance and particle velocity obtained from the 36 event records belong to 9 test shots were statistically analyzed and a PPV prediction equation specific to this site with 95% prediction line were obtained. And also, this equation was used in the derivation of the practical blasting charts specific to this site as a practical way of predicting the peak particle velocity and maximum charge per delay for future blasting. A risk analysis was performed by using this equation. In the light of this analysis, preliminary blast design model was proposed to be used in this coal mine for overburden excavation.

Jan 1, 2012

By John Atkinson, Steve Repola

This paper will describe two blasting plans that have been developed for American Aggregates' Marble Cliff Quarry located near Columbus, Ohio. Two different limestone formations are mined on different levels of the quarry. Each formation requires a different blasting plan which address vibration considerations, crusher productivity, drilling and blasting costs and adjacent neighborhood concerns. Controlled blasting is critical to continued mining operations in this Midwest urban setting.

Jan 1, 1993

By Regina Rocha, Miguel Humpire

One of the challenges within unitary mining operations is blasting, which has a significant downstream impact on the following processes, which is why mining companies ensure the results of the blasting process through joint work with explosives specialists’ companies.

Feb 6, 2023

By Lon Santis, Bill Evans, John Tatom

Debris data from the Department of Defense Explosives Safety Board’s Project ESKIMORE full-scale explosives event test program are compared to quantity-distance (Q/D) standards and quantitative risk analysis (QRA) methods. The ESKIMORE test program involved quantities of explosives ranging from 1,000 to 60,000 pounds detonated in typically sized structures made of metal and concrete. Debris from these events was extensively surveyed and catalogued. The debris patterns from these events show varying degrees of directionality normal to the walls of the structures. These density patterns are overlaid an existing explosives storage site that is comparable to the test conditions. Analysis of the debris patterns in relation to Q/D standards shows that exposures located beyond the Q/D arc but along the normal to walls of potential explosion sites (PES) may have much higher debris density than exposures at the same distance on the corners of the same PES. Analysis of the debris patterns shows that predicted patterns using the QRA tool IMESAFR v2.0 closely match actual patterns. Additionally, IMESAFR based QRA methods are able to quantify the different risk levels of being exposed along the wall’s normal as compared to being exposed on the structure’s corner. Methods and decision making criteria to mitigate risk based on the directionality of PES debris are presented. Copyright ©

Jan 1, 2015

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By Barbara Rutter, Shonn Kevin McNeil

"This study discusses how a prototype was built to measure the sonic velocity in powdered explosives.The sonic velocity of an explosive is a benchmark to determine if the explosive deflagrates or detonates;however, little work has been done to determine this value for powdered explosives. This paperdiscusses the results of the initial prototyping tests where two known mediums, air and water, were used for validation. The prototype did record the sonic velocity within the known velocity ranges of air and water; however, a few depths did not fall into this range. This prototype could be used for testinggranular materials."

Jan 1, 2017

By G. Walsh, M. T. Wild

In this paper the performance effects of linear shaped charges will be discussed. Different sized charges were tested and reviewed based on their performance used with a typical detonation method vs. detonation with a line wave generator. The goal of the project was to determine if the linear shaped charge had better performance with an ideally linear wave moving through it, verses a swept wave that is currently used. A line wave generator is a flexible sheet explosive formed into a triangular shape with holes placed in strategic places to cause a detonation wave to become linear across the width of the triangle. A standard linear shape charge with a detonator in the side of the charge was be detonated against a witness plate to get a standard depth of penetration. A second standard linear shape charge with a detonator connected to the top of a line wave generator, the line wave generator placed on top of the linear shape charge, was be detonated against a witness plate to get a comparison depth of penetration. All charges had a standoff 1.5 times the width of the cavity, allowing the data to be compared to the control charge. Computer modeling was intended to be used to predict the results from testing these designs in the field. The actual results were compared among themselves.

Jan 1, 2011

By Joseph Indeck, Seokbin Lim, Andrew Thompson

In the design of explosively driven penetration devices, understanding the impact conditions between the explosively propelled penetrator and the target is one of the most important steps in optimizing the performance of the device. These impact conditions are especially prevalent when a shaped charge jet impacts concrete, which is not an ideal target material. The specific impact conditions, including but not limited to the impact angle and jet properties, create a great deal of variability that affects the performance and penetration of the shaped charge. The large amount of impurities and voids in concrete, along with its heterogeneous nature and the general strength characteristics, make concrete a non-ideal material for shaped charge jet penetration. These material characteristics lead to a highly non-linear deformation behavior of the concrete target during a hyper-velocity impact.

Jan 1, 2011

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In-hole detonation pressure measurements are unusual in the production environment of a mining operation, partly owing to the hostile conditions to which recording equipment and pertinent probes must be subjected and, partly by the constraints of the production cycle. In recent decades, detonation pressure measurement techniques have been developed using low carbon resistors (LCR)-based gauges. They are cheap, relatively easy-to-operate, robust and with a high percentage of success in both open-pit and underground mining. Detonation pressure measurements are extremely important when carrying out numerical modelling to simulate explosive induced vibrations, since simulation results are highly dependent on the pressure-time history applied on the blasthole wall. Analytical equations have typically been used to model the pressure-time history; however, they usually do not adequately represent the behaviour of the explosive in terms of: peak pressure reached, rise time, mean frequency, decay and shape of the signal. Experimental records may be directly used instead of utilizing synthetic signals if they are available. In this work, (LCR)-based gauges are used to measure detonation pressure inside a production blasthole. The operation principle of the gauges utilized and the instrumentation layout is described in detail. A flexible resolution USB oscilloscope with high sampling rate has been used to catch the elusive pressure peak event. Measurements were carried out in production blasts fired with ANFO (0.86 g/cm3) in an underground mine––this also includes velocity of detonation (VOD) records––. A procedure based on the shock impedance matching has been developed to calculate the detonation pressure due to the characteristics of the gauges prevent its direct measurement. Detonation pressures obtained range from 1.71 to 2.97 GPa (248.01 to 430.76 ksi) which are in line with pressures calculated from the VOD records. Mean frequency and rise time analysis shows that 2 of 3 signals cannot be described using typical analytical equations.

Feb 6, 2023

By Jan Westberg, Roger Holmberg, Bernt Larsson

Over the last couple of decades there has been an increased demand from the market for precision detonators, partly because of a need for better blasting results and partly because of a need for better vibration control. Today's detonators have a pyrotechnical delay element which gives a relatively high time scatter, increasing with the length of the delay time.

Jan 1, 1988

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock. The first stage of the study was the recognition of the rock blast process in question, assessing key parameters that characterize this whole operation: geomechanical characteristics of the rock mass, implementation quality for drilling pattern and explosives charging (collar position, hole depth, explosive charge length and stemming size) and recognition of current blast designs. The central element of this study was the creation of a vibration attenuation and seed wave model which has allowed the characterization of this particular rock mass present in a region determined by the Minas-Rio team. The model is based on a near field vibration test, constituting a powerful tool in the design of blast parameters. The blast design developed from the damage model simulations basically modified the timing and sequencing. The aim of this study was to improve the fragmentation resulted by the blasting, considering the particle size requirements demanded by the primary crusher and to increase the productivity of the loading and hauling operations. The results were analyzed considering the effective productivity of the two different fleet types of shovels, where the authors have analyzed more than 46000 values of productivity from September 2017 to August 2018, taken from the Dispatch system. A significant increase in effective productivity of these load equipment was observed, 7% to the PC4000 fleet and 2% to the PC5500 fleet, values supported by statistical parameters and hypothesis tests.

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock.

Feb 1, 2020

By Andrew Moore

It has long been common practice to conduct drilling and blasting operations at surface quarries in the Midwest in close proximity to near-vertical highwalls. The main reasons for such an approach, and the limited use of adequate safety controls, can be associated with higher costs, operational constraints, lithological requirements, property boundary restrictions, inadequate quarry planning, or a lack of understanding of highwall risks. Working in proximity to highwalls, without effective controls, exposes personnel and equipment to increased risk of incidents. In recent history, there have been isolated incidents involving equipment damage, or personnel injury/fatality around the United States. However, the Midwest market has largely escaped the effects of such incidents, even though the exposure rate is high. Awareness about this matter greatly increased on January 19th, 2021, when a significant incident occurred at a quarry near Green Bay, Wisconsin. As a crew was loading a typical blast near a highwall, a ground fall occurred, and multiple rock fragments struck a laborer working on the bench below. This individual sustained significant and life-altering injuries.

Feb 6, 2023