Search Documents

By Kush Patel

This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser.

Feb 1, 2020

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

By Luiz Guilherme Isfer Maciel, Marilena Cardu, Fernando Golin, Jacopo Seccatore

"This study applies the concept of the difficulty of tunnelling by drilling an blasting (D&B) to selectedcases from the Brazilian tunnelling industry. The difficulty of tunnelling has been defined in previouswork as the difference of specific drilling (SD) from industrial average trend: easier when SD is lowerthan average, more difficult when SD is higher than average. Results show how tunnels in Brazil tend tobe unrealistically more difficult to excavate when compared to similar excavations in similar geologies elsewhere in the world. It is thoroughly discussed the reason for such anomaly (up to +90% SD compared to industrial average). One reason could be the lack of options amongst explosive products on the brazilian market. Only ANFO and explosive emulsions are available in Brazil. Lacking high VOD(Velocity of Detonation) products might result in reducing the maximum allowable burden amongstproduction holes, therefore increasing SD. Another reason could be found in the tunnel designers’tendency of choosing D&B as excavation method for weak rock masses that would benefit from mechanical excavation. The reason to this tendency can be partly found in the lack of availability of mechanical excavation machines in the brazilian market. Blasting in weak rock masses requires more careful smooth blasting, hence a closer spacing amongst contour holes to avoid costly overbreak: this increases SD. A third reason could be found in the lack of skill amongst the local workforce. When dealing with unskilled workers the blast designers naturally tend to avoid highly optimized blasts thatrequire very skilled workforce to be realized on field. The designer in this case tends to leave the blastdesign simpler but more robust, at the cost of higher specific drilling and specific charge. The conclusions suggest that this unrealistic difficulty when compared to world average could be a simptom of the so-called “Brazilian cost” within the tunnelling industry."

Jan 1, 2017

By Julijan Bratun, Joze Kortnik

Production of technical stone is an important economic branch in Slovenia. In 2009, we had 95 dolomite quarries, 27 limestone and 6 silicates quarries, according to the Ministry of Economic Affairs. Together they produced nearly 15 million tons of aggregates. The production in quarries is mostly performed with drilling and blasting method and only a minor part with other method like mechanical mining method.

Jan 1, 2011

By Sérgio Augusto Ferreira, Alan Gerson Diaz Butron, Carlos E. Arroyo, Marcus Neves, Jorhs Enrique Casimiro Huayhua, Dieggo Santos, Eventomar Junior

The presence of natural underground cavities is normally a characteristic of iron ore deposits, specifically in tropical deposits. Brazil and the United States are the only countries that have a legislation to protect these structures, but in Brazil this legislation is very specific for the existing cavities in the federal territory. These cavities are classified by their level of relevance as high, medium, and low. From this perspective, its preservation becomes mandatory, especially, for those of high relevance in order to protect the species (flora and fauna) that live in them. When these structures are within the production phases, it becomes a challenge to exploit these reserves with the use of commercial explosives, since these structures condition and may restrict the use and amount of explosive charge. This paper presents the methodology of controlled blasting associated with predictability via realistic simulation in production polygons, applied in a Brazilian iron ore mine where there is a presence of high relevance natural cavities with restrictions in relation to the limits of Peak Particle Velocity (PPV), which is product of detonation.

Feb 6, 2023

By Tyler Acorn

In December of 2009 an estimated one million ton slope failure activated a 10 million ton mass impacting use of the main ramp system in the Newmont Gold Quarry pit. The failure left behind a 400 foot (122 meters), vertical to sub vertical scarp feature and shut down production in the lower benches of the pit.

Jan 1, 2011

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By Mario Dobrilovic, Zvonimir Ester, Vinko Skrlec, Vjecislav Bohanek

The first public garage in the city of Dubrovnik has been built in highly urbanized area, on location Ilina Glavica. The excavation of the building pit has been done partly by construction machinery, i.e. by hydraulic hammer for excavations and partly by drilling and blasting. In the vicinity of the building pit there are houses, buildings and two schools. Drilling operations and blasting have been performed during the working hours while regular school classes have been held and activities in other buildings took place. The nearest structures are some 5 to 10 meters (16.4 to 32.8 ft) away from the building pit, which makes it even more difficult to perform blasting operations in the urban environment. For the purpose of determining safe and permissible oscillation velocity limits, i.e. the proportion of seismic effects of blasting, a trial blasting has been conducted. The permissible mass of explosive charge has been determined by original method respecting the requirements of existing standards (ISO 4866, DIN 4150, US BM 8507), which determine the permissible oscillation velocities in relation to their frequencies. According to measuring results of the oscillation velocity during the test blasting the design parameters of blasting field have been corrected and zones have been established within the excavation area considering the possible effect of blasting to the building pit environment. Further blasting operations have been performed in stages, in smaller blasting fields with deck charge within a blast hole while respecting the requirements of the transport possibilities for the blasted rock mass within the building pit and performance of control measurements of oscillation velocity for each blasting. Through application of all the protection measures, design solutions and systematic control of performance of activities the complete excavation by blasting has been completed without any damage on neighboring structures/buildings. This article presents these solutions and methods for reduction of seismic impact of blasting to the environment.

Jan 1, 2009

By J Lyall Workman, Peter N. Calder

"Presplitting is a technique mines and quarries may use to produce high quality final pitwalls. Damage from backbreak can be minimized, thereby insuring the final pit walls standat the designed angle. Thus costly excess waste removal is avoided. Safety in the pit isenhanced. Control blasting is an essential component of procedures to maintain the stabilityof final pit walls prone to failure."

Jan 1, 1993

By Catherine L. VanOmmeren

Emulsion quality characteristics such as shelf life, handling, and sensitivity are critical to the end-user. It is therefore important that the consumer be prepared to ask his suppher specific questions. To do so, he needs to have a basic understanding of what an emulsion is and how emulsion properties can affect safety, performance, and environmental impact. The criteria to be covered include: energy, velocity, sensitivity, minimum priming, shelf life, pumpability, effect of AN quality, over-the-road handling, and formulation. The consumer will learn how each of these properties can directly affect him. The information will enable him to set minimum standards in product selection, blending, and application.

Jan 1, 1992

By Gabriel Gonzalez, Paulo Couceiro, Luis Manriquez, Alejandro Gutierrez, Juan Navarro

A high-stakes blasting campaign was successfully executed at a major open pit copper mine in northern Chile. This operation posed a significant technical challenge due to its immediate proximity to the tailings dam - a critical infrastructure whose structural integrity depends on strict control of blast-induced seismic vibrations. The geological complexity of the area, characterized by upper andesite interbedded with caliche (carbonate), further complicated the operation. This lithological composition, known for its high tenacity and cohesion, posed additional challenges for achieving effective fragmentation, necessitating a highly customized blast design and loading strategy. The campaign included four production blasts and one secondary blast, all executed under the constraint of not exceeding the Peak Ground Acceleration (PGA) threshold of 0.64g, as defined by the Maximum Credible Earthquake (MCE) scenario. To ensure compliance, geophones were strategically installed at three monitoring points (P1, P2, and P3) on the dam to capture real-time acceleration data. The use of specialized blast patterns, precise stemming control, and electronically sequenced detonations ensured that all recorded accelerations remained well below the critical threshold. A total of 496,163 tonnes of material were safely blasted, with 8,452 meters drilled and powder factors ranging from 419 to 594 g/ton. Therefore, this case study exemplifies operational excellence in controlled blasting, demonstrating the feasibility of safe mining near geotechnically sensitive zones through predictive modeling, rigorous QA/QC, and post-blast analysis.

Jan 26, 2026

By Panagiotis (Takis) Katsabanis, Lyall Workman, Jack Eloranta

The reduction of metallic ores to concentrate consumes a great deal of electrical energy. In the past two decades, a number of case studies have demonstrated a beneficial relationship between powder factor and grindability. However, changes in mill performance cannot be attributed to changes in feed size alone. Blasting energy and the distribution of that energy appears to affect subsequent comminution beyond crushing. This experience has prompted researchers to attempt to duplicate and quantify the mechanisms involved. To date, published reports indicate a measure of success. However, the blast engineer and the mill engineer still lack the tools and basic understanding necessary for full drill to mill optimization.

Jan 1, 2015

By Richard Turnbull, James Purssey

"The Northconnex Project is a twin nine kilometre tunnel in Sydney, Australia, linking the M1 PacificMotorway at Wahroonga to the Hills M2 Motorway at West Pennant Hills. Access to the tunnels will befrom portals at either end and from three vertical shafts spaced along the length of the motorway. These shafts will provide access for equipment, plant and personnel, removal of spoil during construction,ventilation, and emergency egress points during tunnel operation. The three shafts have a 12 m x 16 m (39 ft – 53 ft) cross sectional area and depths ranging from 45 m to 91 m (148 ft – 299 ft). The vibration limit for the shaft blasting was set at 10 mm/s ppv, with residential properties as close as 31 m (102 ft) and the existing M1 motorway 80 m (262 ft) away. The traffic volume for the M1 is 80,000 vehicles per day and Northconnex will provide an additional 100,000 vehicle capacity. "

Jan 1, 2017

By Jorge Cárdenas, José Luis Hurtado

The critical distance determination test through direct recording for the mine in Phase 03 was carried out in January 2024, and in it the vibration and pressure models were obtained for the Sedimentary breccia unit. The method of obtaining the records is based on the capture of individual pressure waves generated by distant loads, sequenced in periods of 600 ms for easy identification. The test set up corresponds to a variation of that used to obtain the vibration model, and uses 08 wells for loads and 04 for instrumentation. The results apply a safety factor of 1.2 and 1.5, being 16,000 PSI and 13,250 PSI respectively. The values are valid for any distance greater than 5.5 m, this being the minimum established between wells for loads according to the configuration defined in the field, also considering that in 5.0 m of instrumentation the section of the drill hole with the sensor called S1 collapsed. The results of the analysis of the test, generated with Heavy Anfo 82 explosive, with a final density of 1.15 g/cc, are presented. The results of the modeling and generation of the graphs and tables presented show behavior in line with the concept of scaled distance. It is important to consider that in water conditions there is a high impact by the condition, which causes the records to be higher than those expected in dry conditions and present less variability. It is for the above reason that the row corresponding to distance with safety factor 1.5 is declared valid. The results are only valid for the rock analyzed, whose medium is homogeneous and constant in terms of lithological composition and that present similar resistance characteristics, fracture frequency and water table levels. As future steps, the objective is to quantify the increase in pressure generated between wells by analyzing time and sequence factors. This analysis aims to explain the occurrence of dynamic pressure events in areas where critical safety distances are observed.

Jan 21, 2025

By Braden Lusk

The problem of predicting damage in densely developed areas due to incidental or malicious explosions is one of considerable importance to local, state, and federal governmental bodies. The difficulty of making such a prediction is confounded by the urban canyon phenomenon as the shock wave intensifies or rarefies depending upon the particular arrangement of buildings. The specific method detailed herein used a Computational Fluid Dynamics solver, ANSYS AUTODYN, to operate on Geographic Information Systems data, ArcGIS, which captured the geospatial relationship between the various buildings in downtown Oklahoma City, prior to the Murrah Building bombing. The model of Oklahoma City was first developed using the building footprints and elevations provided by the ArcGIS database. Due to the sheer size of the problem, the model was then subdivided into annular zones of increasing distance from the center of the blast. Each subsection was then solved using an Euler model in a cascading fashion with the output of the preceding model forming the input of the present model. To further reduce computational time, the size of the Euler nodes was increased at each stage as the section area increased. Due to the loss of precision in capturing peak pressure values when using larger size nodes, it was necessary to perform a transformation on the results using one dimensional wedge calculations with higher precision. The Murrah Building bombing event was an excellent case study due to its available ArcGIS data and the level of documentation of damage to surrounding structures due to the blast. The results from the staged CFD calculation were then used to develop a damage potential contour map. The documented incidents of damage in the area surrounding the Murrah building were then compared to the model generated damage potential contour map. Copyright ©

Jan 1, 2010

By David Porter, Nathan Rouse

The implementation of presplit perimeter control in underground mining as a method to decrease dilution yields positive benefits throughout the current and future mining cycles. A case study to understand the benefits of reducing overbreak and underbreak in a cut and fill mining cycle was performed to quantify the reduction in backbreak. The study was performed in a control section of the mine where a presplit perimeter control design was utilized for a length of heading. This control heading was then compared to the existing standard blasting design within the same mining zone. The comparison included multiple aspects of the mining advance including overbreak, dilution of waste, dilution of Cemented Rock Fill, bolt counts, and cycle times. Once mining in the control section was completed and mining commenced in adjacent headings, blast damage due to blast design could be quantified.

Feb 6, 2023

By Roger G. Sprague

With the passing of time, changing marketplaces and years of hard service, coupled with new machines, increased productivity, rapidly improving technology, equipment which used to be the latest in modern mining have now slipped into obsolence. Mining companies need reliable, productive equipment in order to compete in today's market. In Western coal mining, as coal seams become deeper, older equipment must be replaced with that which can do the job more efficiently.

Jan 1, 1998

By Raphael Trousselle, William Reisz

The blasting industry is now well into its second decade of commercial use of electronic detonators. As an increasing number of blasters are introduced to the technology, the benefits are becoming more widely monitored and accepted in many surface blasting operations. However, their use in underground applications is not yet as widely established. This is primarily due to the distinct cost dynamics and processes associated with underground lasting.

Jan 1, 2012

By S. Geerts, J Davidson

The purpose of the experiment was to determine detonation characteristics of various improvised explosives. The test consisted of detonating a pipe filled with an explosive compound inside of a plywood arena. The pipe will be located in the center of the arena to ensure even distribution on the witness panels. Details on pipe dimensions, weights of the pipe and explosive, and the density were recorded prior to testing for use in the model calculations. The same size pipes were used throughout to minimize the variables inherent in testing. The plywood witness panels will capture the fragments so that penetration data was obtained, primarily the surface area of impact and depth of penetration. Through the use of the penetration data in conjunction with a mathematical model the original fragment velocity was determined. The mathematical model was developed to measure lethality of fragments from explosives and was modified to determine the original fragment velocity instead. From this model other variables such as the Gurney velocity were calculated. This test was done with an explosive compound that was commonly found, and numerous improvised compounds. In order to guarantee accurate data all of the explosives used for testing were cap sensitive, to eliminate the need for a booster charge which would introduce many unknown variables. The one common explosive compound that was used was C-4 which has known data in order to show accuracy of the model and calculations. The other 5 compounds chosen will not have this data as they will primarily be improvised mixtures.

Jan 1, 2011