Search Documents

By Ekin Güngor, Berkant Ozdemir, Erkan Bayrak, Serdar Ergün, Sedat Esen

"This paper presents the final wall blasting practices at Eldorado Kisladag Gold Mine in Turkey. Benchmark and improved wall control designs were explained in detail. Kisladag Mine has been implementing a high quality slope stability program on-site. The quality of pit walls is generally considered excellent, with very few wall failures being evident and with presplit hole barrels prominent in most areas of the pit. However, a minor scale slope failure occurred recently at the north-east section the pit. A project was initiated to diagnose the cause of the crest loss and evaluate ways to limit its effect on final walls. Final wall blasting practices and geotechnical designs were evaluated. The work presented in this paper showed that changes to the blasting and geotechnical parameters are required atthe north-east section of the pit. Geotechnical design changes were 10 m bench heights with 70 ° slope face angle at that specific area. Having implemented several geotechnical and blast design changes (elimination of the subdrill for the catch bench, appropriate primer location, more favorable blast tie-up and delays), the crest loss was minimized significantly (<1.5 m) (<5 ft)."

Jan 1, 2017

By Michael S. Wieland

Toxic fumes cause fatal and nonfatal incidents in underground mining, where the working environment tends to trap the fumes, hindering the restoration of nonharmful conditions. Workers can underestimate the residual fume toxicity and return to the work site too quickly. The toxic fumes from charge explosions depend upon a number things: formulation ingredients, mixture uniformity, water resistance, hole contaminates, rock hardness, and dust interactions. Hole-to-hole shock waves and rift compressions can partially desensitize charges, ruin the reaction kinetics, and worsen the fume toxicity. Traditionally the fume hazards for candidate explosives are resolved for a restricted set or tally of theoretical or measured fume components, transformed to standard reference conditions. The relative fume toxicity RFT is the resultant influence reckoned from a formulated sum of concentrations within the tally that are unweighted or weighted with chosen multiplying constants. The RFT result is compared to a rule criterion that represents the worst case tolerable fume toxicity stipulated by regulations or otherwise. The ranking and comparison of different hazard potentials that would otherwise remain unwieldy is rendered tractable by the common format of the RFT notation.

Jan 1, 1998

By Mick Fritz, Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and field controls placed at the shot location. The procedure by which the data is collected and analyzed is paramount to accomplishing the anticipated blast results. lf the geometry of the blast is not measured correctly, then the results will not meet expectations. Measuring the geometry and compensating for bole hole deviations is crucial not only to the lnitlal blast but also for any consecutive blasts. Excessive bore hole deviation can cancel any new technology in use. However the instruments and skills required solving this Issue are readily available.

Jan 1, 1998

By Pr-Anders Persson

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the c.ootext of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of sn explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1995

By Italo Onederra, Jason Furtney, Ewan Sellers

The detonation reactions occurring during rock blasting result in high pressure gas phase products from the condensed explosives typically used in mining applications. After detonation and the initial fracturing, the work done by the expansion of this gas contributes to burden movement and further rock fracturing. Before all of the energy in the reaction product can do useful work on the rock, some of this energy is lost to crushing and possibly to gas venting to the atmosphere. Borehole gas pressure decreases by three principle mechanisms: (i) expansion of the borehole cavity, (ii) flow into the fracture network, and (iii) flow through the stemming. To simplify the problem and to get a better understanding of the interaction of these mechanisms, a simple model for each of these mechanisms is developed. A comparison is made of the time-scales and the influence on burden movement for each. A comparison of gas flow behavior is made between typical ANFO and emulsion products.

Jan 1, 2012

By Jaki Wilson, Les Armstrong, Neville T. Moxon

Low shock energy ANFO (ANFO) mixtures have been developed for use in fragmenting weak overburden materials and reducing damage.outside the blast zone in dry conditions. These mixtures can be readily produced on a minesite using conventional equipment and are formed by mixing low density additives such as polystyrene, bagasse and sawdust with ANFO.

Jan 1, 1990

By Earl C. Hutchison, Wade C. Hutchison

T 0 effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre- and postblast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

AQUILA Mining Systems Ltd., designs, develops and delivers systems for measurement, analysis, simulation, control and automation to the mining, construction and petroleum industries. The objective of current efforts by AQUILA is the continued development and refinement of computerbased systems and techniques to automatically process monitored performance data from surface blasthole drills and mining shovels, and the management and coordination of these pieces of equipment by GPS (Global Positioning Systems).

Jan 1, 1994

By S A. Steyn, P Terrett

Air decking has become a widely practised method internationally for modifying fragmentation results and providing cost savings from reduced explosive consumption. Duvha has been applying air deck technology to overburden and midburden blasting for a few years. A thorough evaluation of air decking at Duvha has been made by instrumenting a number of blasts and analysing costs from direct savings in reduced explosives costs to savings in improved dragline productivity.

Jan 1, 1995

By Robert Lee, Pertti Paavola

Automated vibration monitoring and web-based data distribution has proven itself on the largest single construction project ever undertaken in Finland. The excavation for the Kamppi Center Project in the center of Helsinki was completed in November of 2003 and involved the removal of over 200,000 m3 (260,000 yd3) of rock and over 1,700 individual blasts. A system was installed, incorporating 37 discrete monitoring points located throughout an underlying metro station, and other surrounding underground and surface facilities. After every blast, vibration data was automatically transferred from the monitoring network to a server database. Stakeholders were able to access and review vibration reports on a password-protected website within 90 seconds of each blast. This allowed engineers to verify that recorded levels were in compliance with established limits, before proceeding with subsequent blasts. The data was also imported into a semi-automated Scaled Distance tool for analysis using linear regression techniques. This was used to determine, and adjust for trends in blast-induced vibration.Copyright

Jan 1, 2004

By Johnny Lyons-Baral, John Kemeny, Don Kraemer

Ground vibrations from blasting can result in the degradation and failure of rock and soil exposures, as well as damaging neighboring houses and buildings. At the same time, vibration provides an opportunity to regularly monitor the rock and soil exposures. If a geophone or accelerometer is attached to a rock block or wedge on a mine slope, for example, then blast vibrations will regularly “sound” the rock block and the resulting vibrations can be used to assess the stability of the rock mass in the neighborhood of the accelerometer, as well as monitoring the properties of the blast. This paper describes the development of a wireless sensor network based on inexpensive MEMS accelerometers for blast monitoring and rock and soil structural health monitoring. The wireless sensors are placed at various locations in and around an open pit mine or quarry, and transmit data to a central source after ground vibration events occur. As described in the paper, a variety of wireless and non-wireless accelerometers were tested in actual field conditions. This includes the monitoring of over 30 blasts at an open pit mine in Arizona with as many as nine simultaneous accelerometers. Matlab was used to process all the data and develop innovative methods to view and interpret the data. This includes the use of the wavelet transform to determine resonance frequencies, and the use of both ground resonance frequencies and scaled-distance peak particle velocity (ppv) relationships to assess slope stability. As part of this research, a three-dimensional point cloud environment for viewing and analyzing the vibration data from the sensors has also been developed.

Jan 1, 2014

By Charles Zdazinsky

Over-break is undesirable in underground civil construction because it excessively damages rock along the perimeter of the tunnel, which directly influences the cycle times of advancement. A quicker cycle time for each process is required to optimize the operation and therefore minimizing over-break is essential for operational success.

Jan 1, 2015

By Gabsoo Kim, Rulin Yang, Dave Kay

Blast vibration data, such as PPV are usually scattered. In many cases, plots of PPV versus the charge weight scaled distance are so scattered that useful trends from different blast designs cannot be identified. The scattering of the data may be attributed to the inaccuracy of the PPV measurement, the definition of the scaled distance from a multiple-hole production blast, and the measurement of distances and charge weights. The error from vibration measurements is one of the major contributors to the scattering of the plots. If accurate monitoring is conducted, improved design options may be identified. This paper documents two case examples that compare different vibration sensor couplings. The first case shows mounting accelerometers at spots that protrude from the ground, compared with the sensors that were mounted on a flat ground surface. The second case compares data from loose-sand buried geophone with that from sensors coupled to the ground using concrete blocks.

Jan 1, 2014

By Roberto Folcht

The obligations of the European Directive 96/82/EC on the control of major accident hazards, the so-called Seveso II Directive, became mandatory within the E u ropean Member States February 3, 1999. Explosive products have been included within the Seveso II Directive, in the categories of substances capable of generating a major accident. In addition to taking “all measures necessary to prevent major accidents,” explosive manufacturers are also obliged “to limit their consequences for man and the environment.” However, for explosives in particular, no pro c e d u res, nor specific re f e rence values for damage calculation, are given either in the Directive or in the corresponding Italian Legislation, “Ministry of the Environment decree of 20 Oct. 1998.” This article presents a simplified but scientifically rigorous approach for the first approximation calculation of the effects on the surrounding area following an accidental explosion. As an example of the method of calculation, the damage areas in a hypothetical explosives manufacturing facility, as shown in F i g u re 1, will be anal y z e d . The method proposed in this article can also be used for the analysis of explosions of gas in tanks or pipelines,

Jan 1, 2004

By George Harrison

A great many labor leaders and others advocate shot-firers as the acme of relief for all the dangers connected with solid shooting, and where large quantities of powder are used in one blast in coal mines. Legislative bodies in several mining States have enacted laws providing for shot-firers in mines under such circumstances, the blasting to be done at night after the miners have left the mine. With all due respect to the opinions and honesty of purpose of these advocates of shot-firers, it is evident that a great many of them are not considering this important question in the broad sense it deserves and should be considered.

Jan 1, 2008

By Roger S. Jackson

"This study interprets vibrations produced by single underground shots, recorded on surface by 135 digital seismographs laid out in four linear arrays. Several vibration anomalies were observed and are investigated. A novel method of displaying the blast-induced vibration iso-contour data relative to the three-dimensional representations of the geological rock units and structures leads to the following interpretations:• The identified faults commonly dampen or amplify vibrations, on the evidence of the peak particle velocity,• Strong anisotropy of geologic formations produces different vibration attenuation in the various directions of interest,• Low-vibration “depressions” can be related to the presence of faults, and• Higher vibration levels than expected based on ‘scaled-distance’ principles are observed close to intersecting faults.The interpretations from this study document a better understanding of the geotechnical influences on blast induced stress wave propagation in a geologically complex area. The practical benefit of this understanding is better control of surface vibrations, experienced from underground mining activities."

Jan 1, 2010

By Narendra Gupta, Gaurav Srivastava, Abhinav Sharma

From the days when plain detonators and safety fuse were used for initiation of commercial explosives, the commercial blasting and mining industries have made rapid strides. With the advent of electronic detonators in the late ‘90s, the face of commercial blasting was changed forever. The Mining Industry in India initially took a while to embrace Electronic Blasting Systems (EBS), however, more recently the industry has taken to EBS in a big way.

Jan 1, 2015

By William D. Hissem

For those blasthole applications which require the use of holes ranging from 1” to 5.5” in diameter, the use of top hammer drills has been the equipment of choice for several generations of drillers. Pneumatic compressed air and hydraulic compressed oil systems represent the primary technologies which are available to the drilling practitioner. While both employ the same operating principals, the characteristics of performance, cost, and reliability can be markedly different between technologies and manufacturers.

Jan 1, 1998

By Bruce Vandenberg

Two tests were set up as part of the course given by Blasting Analysis International. Both tests were performed using the prototype Velocity of Detonation Recorder (VODR). The prototype has several limitations, which have been rectified for the production units.

Jan 1, 1990

By Sushil Bhandari, Amit Bhandari

Blast optimization in open-pit operations is a task that often remains at a theoretical stage. Indeed, when it comes to operational blast design and onsite implementation, time restrictions and field conditions make it difficult to execute a planned pattern accurately and optimization according to local conditions is even more difficult. For example, adjusting a drill pattern to a complex face geometry is not something that can be easily undertaken on site. Blasters and engineers will do their best trying to distribute boreholes over the bench and even then, it can take them hours to achieve an acceptable layout. Similar situations occur with delay sequences, when trying to adjust them to address selectivity or vibration issues. For these reasons, operational blast design will often remain at a very basic level and the required adjustments are laid aside due to the difficulty of implementing them on site.

Jan 1, 2019