Search Documents

By Corry Goumans

The job location is at Bear Lake Hydro Project located north of the town of Sechelt, British Columbia, Canada

Jan 1, 2013

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984

By Douglas Rudenko

When blasting complaints come, as an industry we often immediately look to the ground vibration as the source of the trouble. Often times we overlook or place less emphasis on the collected air overpressure data. Air blast like ground vibration is an undesirable side effect of blasting and can produce considerable structural response.

Jan 1, 2002

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By Changa-Ha Ryu, Hae-Moon Choi, Sang-Don Lee

The rock mass to be excavated is classified using data obtained from the initial site investigation, and the design of excavation and support is then made based on the rock class. Rock classification provides an empirical design with guidelines for tunnel support compatible with rock mass quality and the method of excavation. Although most clients provide standard patterns corresponding to each rock class, the patterns of drilling and blasting have only been used in estimating the excavation cost and not used in the construction stage. The purpose of the study presented in this paper is to establish a standard blast pattern to yield optimum blasting performance along with an attempt to reduce a difference between design and construction. A series of test blasts were carried out at two tunneling sites of Central Inland Highway crossing the country. Long hole blasting was tested in rock mass whose RMR value is over 60. The blasting results were evaluated by measuring degree of fragmentation, advance rate, muckpile distribution, overbreak, etc. Based on the results of test blast, several patterns were proposed for a twolane highway tunnel.

Jan 1, 2005

By R L. Calhoun

A paper on High Pressure Air must start with the industry accepted definition of High Pressure Air and, for the reader who is unfamiliar with High Pressure Air systems, include basic information on which type of Drilling Rigs can benefit from the use of High Pressure Air. The operation of a modern Downhole Drill must also be reviewed.

Jan 1, 1976

By W. Jiao, Y. Yongqi, R. Shan

Soft rock mines are distributed through out P.R.C. And drilling and blasting is still the main method of driving a tunnel in these mines. Traditional smooth blasting has been widely and deeply studied and put into practice in P.C.R since 1970s. But the cartridge and blast hole are both columns, the stress field in the rock around blast hole at the beginning is symmetry around hole axis, and the original cracks in the rock can be activated randomly. So serious overbreak and underbreak at the boundary of an excavation occur often, especially when the excavation is in soft rockmass, and the rates of half-hole marks are generally about 50% in medium rock, and 20-30% in soft rock in Chinese coal mines. For the sake of overcoming the situation, we have been studying directed crack blasting since ten years, and have got some obvious achievements in this respect. Slotted cartridge control blasting in soft rock is studied in this paper. Through model experiments, reasonable decouple coefficient range and slot width are gotten, and unsymmetrical dynamic strain field is analyzed. Through underground test in soft rock with a strength lower than 1OMpa in Dayan Mining Bureau, The results of which the rates of half-hole marks and the nonsmooth grades of the cut contours are 83.3% and 1OOmm respectively have been achieved.

Jan 1, 2000

By Andrew P. Ritter, Douglas A. Anderson, Stephen R. Winzer

We have adopted a unified approach to blast design. Based on earlier research, we chose minimum relief of 3.4 ms/ft between holes in a row and 8.6 ms/ft between echelons to produce good fragmentation. A model has been created which generates the expected ground vibration frequencies from a particular delay pattern. Within the relief guidelines, blast designs have been created to shift the expected frequencies of the ground vibration above the resonant range of residential structures. A programmable sequential blasting machine was used to delay circuits. An extensive three-month seismic monitoring program determined that this approach is successful. From data collected for over a year, we have determined that crusher throughput is up about 10%, frequency modification has been largely successful, peak particle velocities have generally gone down by a factor of 2, and neighbor complaints have decreased drastically.

Jan 1, 1982

By C. Kosloski, E. McCullough, A. Fox, S. Reed

This paper serves as a reference guide for creating or strengthening student chapters of the International Society of Explosives Engineers. This includes chapters that are just starting, currently undergoing transition in leadership, or that are in the process of rebuilding. ISEE student chapters have great potential to increase student involvement and national membership, and can benefit from formalized strategies to help them do so. Several key strategies are introduced and should be employed to promote organizational participation throughout the university system.

Jan 1, 2016

By Trevor Ames

Highwall instability, and sometimes referred to as ground failures, historically are a consistent contributor of mine injuries and fatalities within surface mines. To combat this several efforts, including those from NIOSH (CDC), to educate the mining community with insightful literature focused on hazard recognition and advances in ground monitoring systems have been performed. The question is can more be done or is this our last line of defense to manage potential dangers? Is there a more effective method to reduce hazards presented by ground failures including rockfalls?

Jan 1, 2015

By Dale Preece, Vanessa Berg

This paper presents a two-pronged vulnerability analysis approach for treating minimally reinforced concrete (RC) structures subjected to explosive events. This work was motivated by a heightened interest in homeland protection involving both malevolent and accidental explosions and the need for assessment of critical facilities subjected to an explosive detonation. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN, while the second part of the analysis employs Single-Degree-of-Freedom (SDOF) methods, each predicting the dynamic response of the minimally RC walls, slabs and columns to explosive loading. The concrete is treated with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model, which accounts for failure mechanisms in brittle materials. Predictions from AUTODYN are verified using the equivalent SDOF reinforced concrete code, SPAn32, developed by the US Army Corp of Engineers and agreement between the results indicates a high level of accuracy in both methods of analysis, allowing for accurate predications of airblast-structure interactions and failure mechanisms.

Jan 1, 2004

By J T. Schamaun

Recent applications of explosives and blasting agents to rubble rock have led to requirements for more elaborate design and analysis methods. In most blasting uses, it is necessary not only to fracture the rock, but also to move the broken rubble in a predictable manner. Many in situ extraction techniques require; rubblization to take place in a confined region where rock motion is a predominate factor in creating a permeable broken bed. In this paper, an engineering model is presented which describes the large rubble motion during blasting. This model is intended to provide the blast designer with a tool for evaluation and further refinement of blasting patterns and timing sequences.

Jan 1, 1983

By U Nyberg

Peak particle velocity (PPV) and distance measurements from a single-charge blast test conducted by Swedish researchers in iron ore at the Kiruna Mine in northern Sweden are presented. They are used along with theoretical PPVs calculated using an equation based on hydrodynamics to determine a damage distance range caused by a single charge. This equation, which relates PPV to explosive properties, charge geometry, and distance from a charge, was then applied to a charge of different geometry that was used in drift rounds. A comparison between calculated and measured PPVs suggests that the stoping holes likely damage the easer hole locations, and the easer holes produce damage to the perimeter hole locations. The practical effect is that typical damage limit predictions based on measurements conducted in fresh or undamaged rock are conservative. This suggests that even when perimeter control is not exercised in drifting (i.e., the perimeter holes are fully loaded), the resulting damage may be less than normally expected due to the wave damping effect of the pre-damaged rock. Due to the damping effect, poor perimeter blasting practices are somewhat self correcting. However, it must be strongly emphasized that well-engineered blast designs with perimeter control are highly beneficial in relation to both economic and safety aspects.

Jan 1, 2011

By V R. Sastry, D P. Singh, N R. Thote

Rock parameters which are uncontrollable impose restrictions on the procurement of desirable fragmentation. Blast design parameters which are controllable prove to be important tool in blasting operations. An attempt was made by the authors to investigate parameters which causes big oversize boulders in overburden blasting. A case study of coal mine is discussed in this paper.

Jan 1, 1995

By R Heater, G Glynn

Various small diameter commercial grades of slurry and emulsion explosives were tested and compared. Velocity diameter curves for confined and unconfined charges were established and the effects of temperature and hydrostatic pressure on critical diameters and minimum primer weights were determined.

Jan 1, 1984

By Leslie Taylor, Kevin Genson

This paper reports on an experimental study of the effect that bottom shaping might have on the impulse delivered to a light armored vehicle due to a buried mine detonating beneath the center of it. The study was restricted to explosives buried in saturated sand and three parameters were varied within the study: bottom angle (0 degrees to 21 degrees), depth of burial of the explosive (1.02 mm to 12.7 mm), and stand off distance (0 mm to 38.1 mm). Six hundred and thirty six milligrams of explosive was used as the explosive load. It has been shown in previously published work [1,2] that Hopkinson scaling works well for the determination of impulse loading on a semi-rigid target plates. Therefore in terms of a full scale test using 4.54 Kilograms of explosive the parameters investigated would cover a DOB of from 19.56 mm to 243.84 mm and a Stand off distance from 0 to 734.06 millimeters. These values nicely cover those of interest to the Marines with regard to the AAV (amphibious assault vehicle). Four angles were investigated at all DOB’s and Stand off distances – 0 degrees, 7 degrees, 13 degrees, and 20 degrees. The results show that reduction in impulse delivered to the target is achieved with an angled bottom on the target plate with a major reduction occurring before the 13 degree angle is reached. Hence vehicles with quite modest bottom angles could help greatly in load reduction with very little loss in utility.

Jan 1, 2008

By Edward J. Jr Walter, Edward J. Walter

The vibration problem is approximately fifty years old. The original investigation of the U.S. Bureau of Mines was begun in 1930. Significant investigation into the problem was done by Crandell, Langefors, et al, Edwards and Northwood, and again by the Bureau of Mines. This resulted in an effective Safe Limit standard expressed in particle velocity as 2.0 inches per second.

Jan 1, 1979

By Michael Louis, Charles Dowding

Concern over construction vibration-induced cracking has led to development of a new approach to vibration monitoring called autonomous crack measurement (ACM) and illustrated in Figure 1. This paper describes the concept as well as sensor performance in the first test house fitted an ACM system. Response of three cracks in this concrete masonry unit (CMU) house was measured as part of the system verification. ACM employs a single sensor that measures both weather-induced micrometer changes in crack width and those produced by habitation and ground motioninduced vibration. This comparison is displayed in real time via the Internet without human interaction. Graphic display through the Internet provides a new pathway for communication with the public. Such visual comparison of changes in crack width provides a simple alternative to the present system of comparison of measured and allowable vibration time histories. Measurements reported herein show that weatherinduced response of cracks is greater than that caused by presently allowable construction-induced vibration.

Jan 1, 2003

By Split Engineering Chile Fernando Fernandez

Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations.

Jan 1, 2015

By Michael S. Wieland

This report discusses measurement techniques utilized in and trend results obtained from research on delay blasting malfunctions in underground coal shots at the U.S. Bureau of Mines. Charge malfunctions occur during delay blasting in underground or surface mines, rendering the explosive operations more hazardous and less productive. Modern instrumentation techniques reveal several types of reduced charge performance, resulting from cross-hole interactions. Two receptor (wave-target) charge malfunctions were detected in fourteen shots that were undeniable. There were other receptor charges that exhibited under-performance by registering out-of-tolerance or noticeably reduced detonation rates. Delay blasting generates tremendous shock waves and rifting forces that fracture and heave the surrounding stratum and unfortunately damage remaining unfired charges. This report contains two graphs, representing roughly 1% of total records, that show donor (wave-source) charge shock waves and rift (reaction-to-heave) compressions. These debilitating wave impacts precipitate modes of reduced charge performance ranging from weak detonations or misfires to sympathetic detonations. As recognized from previous research, impaired charges react poorly, perform less useful work, and yield fumes with atypical higher toxicity.

Jan 1, 1995