Search Documents

By Ming’an Wei, Chuanyao Sun, Zhenguo Song, Zengwen Dou, Yangge Zhu

"The effects of pH value and dissolved oxygen(DO) in the pulp to the Eh and flotation recovery of pyrite were investigated using potential online detection system. The effects of DO on the Eh and flotation recovery were tested which DO changed from 0.5mg/L to 19.5mg/L in six different pH buffer flotation systems (pH: 4.00, 5.62, 6.86, 9.18, 10.01 and 10.96 respectively). Results of potential detected online demonstrated that the pyrite electrode has nearly the same response to potential as with platinum electrode for the FeS2-xanthate-H2O flotation system under the study conditions. Pulp potential and recovery of pyrite were remarkably influenced by pH, both of them decreased with the increasing of pH and, especially, sharp decreased after pH above 9. As the concentration of DO was increased, the Eh was also increased in all the six different buffer solution, while the flotation recovery was decreased. And the amplitude of variation for Eh was not obvious in acidic and neutral solutions, but on the contrary, the change for flotation recovery was remarkable in neutral and alkaline conditions. This may indicate that the flotation of pyrite will be deteriorated in alkaline and high DO concentration conditions."

Jan 1, 2014

By V. A. Chanturiya

The state-of-the-art of mineral mining and metallurgy industry in Russia is characterized by high demand of nonferrous, rare, rare earth metals, and highgrade coal, on the one hand, and by involvement of natural and technogenic minerals with low content of valuable components, fine (nearly emulsion) dissemination of valuable components and close physicochemical and process properties. This calls for high-productive and ecology-friendly technologies for more efficient mineral beneficiation based on intensification of operating and new methods to extract valuable components from rebellious ore and technogenic minerals, relying on the last achievements of basic sciences, combination of dressing and chemico-metallurgical processes and using advanced pyro- and hydrometallurgical technologies. The transition to a new strategy of processing is only possible based on the new technological–mineralogical appraisal of a mineral raw material. Actually, the process mineralogy has a stock of modern high-resolution physical methods for analyzing composition, structure and properties of geomaterials, inclusive of micro- and nano-levels: - Identification of micro- and nano-size noble metals, and natural and induced formations on mineral surface; - Experimental validation of structural phase and chemical transformation of minerals under different energy input; - Justification of choice and mechanism of interaction between flotation agents and noble metals with complex material constitution; - Analysis of structural, phase and chemical transformations of sulfides and rocks under leaching. Thus, process mineralogy is an informational background for a unified theoretical approach to scientific justification of flowsheets of efficient mineral processing. The article gives a brief review of practices that have found application and proved to be of high economic efficiency. Such practices are: X-ray radiometry and photometry separation (Uchalinsky and Gaisky Mining and Processing Integrated Works of ALROSA); selective disintegration (equipment engineered by Mekhanobr-Tekhnika and IPKON RAS); process selectivity enhancement (IPKON RAS, Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Chinakal Institute of Mining, Siberian Branch RAS, etc.); bacterial gold leaching (Olimpiada MPIW, technologies developed the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Nezhdaninsky deposit projects, etc.); combination processing at a mining and metallurgy plant (Norilsk Mining and Metallurgical Company, Yaregsky deposit projects and others); processing of waste: overburden, mill tailings, slag, etc. (Kovdorsky MPIW, Svyatogor JSC, Ural Mining and Metallurgical Company, plants designed by the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Mining Institute of Kola Science Center RAS, Research Institute for Chemical Technologies); water conditioning in mineral dressing circuits (ALROSA, equipment by IPKON, etc.); utilization of process water (ALROSA, Ural Mining and Metallurgical Company, Severalmaz JSC and others). Thus, Russia this time has the academic and engineering background for development of efficient energy-saving technologies for comprehensive advanced processing in accordance with the world’s standards, or even higher in terms of a number of the technologies, which has continually been highlighted by participants of recent international congresses on mineral processing.

Jan 1, 2018

By P. Khattri

At Tata Steel, Coal is washed in gravity and froth flotation circuit at 13-15 mm size and below. Being coal is high in ash (~35%) and difficult washability characteristics (having high (~40 %) NGM at desired ash levels) needs more and timely quality data of ROM for effective optimization and process control. Conventional approach of supplying quality data takes 4-5 hours time. This means during this period, it is assumed that coal is having similar characteristics as of previous set and it is not possible to fine tune during this time which resulted in yield loss. Hence producing clean coal on agreed ash value consistently is a challenging task because of high NGM and variation in input quality. To overcome the problem of collection of representative sample and timely result a new technology was adopted Prompt Gamma Neutron Activation Analysis (PGNAA) technology which is basically an online analyser using Gamma rays as the source to measure the ash content in coal running on a conveyor which gives real time ash analysis. The details of this technological intervention are discussed in details in this paper. Keywords: near gravity material, PGNAA

Sep 1, 2012

By Jiongtian Liu, Guixia Fan, Caom Yijun

A cyclonic-static micro bubble flotation column (FCSMC) is an effective separation device for fine grain treatment. The separation of fine ilmenite by FCSMC was explored in this work. The influence of reagents dosage (regulator, collector and auxiliary collector), pulp density, circulation pressure and aeration quantity on TiO2grade and recovery wasinvestigated.The optimal conditions of a rougher are follows: pulp density 45%, pH 5.0, MOH collector dosage 2800 g/t, diesel oil dosage 700 g/t, circulationpressure 0.19 MPa, aeration quantity 0.8 m3/(m2•min). The optimal conditions of a cleaner are follows: pH 4.0, circulation pressures 0.16 MPa, and aeration quantity 0.5 m3/(m2•min).A pilot plant continuous test with a rougher-cleaner by FCSMC for 72 hours was proceeded under the optimum conditions. Compared with industrial flotation machines, the concentrate grade of FCSMC is 48.11% with an improvement of 1.08 percentagepoints, while the recovery is 82.36% with 13.64 percentagepoints increment. Moreover, the flowsheet is simplified from six parts (a rougher-two scavenger-three cleaner) in flotation machines to two parts (a rougher-cleaner) in FCSMC. Proofs were also provided by the analysis of the by-size grade and recovery of concentrate.Results show the FCSMC is an effective separation device to recover -74 µm size fraction.

Jan 1, 2014

By M. Lundström, J. Aromaa, S. Seisko

"Gold dissolution was investigated in ferric chloride media, promoted as one of the most promising alternatives for cyanide-free gold leaching. The characteristics of gold open circuit potential (OCP) and its relation to gold dissolution rate was investigated. Furthermore, the reaction mechanism of gold dissolution in ferric chloride leaching was discussed. The effect of solution variables, [Fe3+] = 0.02–1.0 M, [Cl–] = 2–5 M, T = 25–95 °C and pH = 0–1.0, on OCP and dissolution rate were studied electrochemically using rotating disk electrode (RDE) and linear polarization resistance (LPR) method with ?cyc = 1000 RPM. The investigated gold OCPs in ferric chloride solutions were found to vary between 597 and 688 mV vs. saturated calomel electrode (SCE) and gold dissolution rates between 1.2·10–5–5.0·10–4 mol s–1 m–2. Increase in temperature (25–55 °C) and ferric concentration (0.02–1.0 M) changed OCP into more positive values, while increase in chloride concentration (2–5 M) decreased it. The logarithm of gold dissolution rate was shown to increase linearly with increasing OCP at the temperature range 25–95 °C, ferric concentration range 0.02–0.5 M and chloride concentration range 2–4 M. A notable increase in the gold dissolution reaction rate was evident at T > 55 °C. INTRODUCTION Currently cyanide leaching is the predominant method used in gold production from primary raw materials (Marsden and House, 2006). However, since the Baia Mare disaster in Romania in 2000, the use of cyanide has been the subject of international concern due to the toxic nature of the chemical posing a significant health threat if exposed to the ecological entities (Hilson and Monhenius, 2006; UNEP/OCHA, 2000). Therefore, several countries e.g., Costa Rica, Czech Republic, Germany, Hungary, Turkey, many states of the USA and provinces of Argentina, have started to ban or limit cyanidation via legislation (Laitos, 2012). Thus, alternative solutions, such as thiourea, thiosulphate, oil-coal agglomerates as well as halides have been investigated in order to replace cyanide as lixiviant (Adams, 2016; Aromaa et al., 2014; Aylmore, 2005; Hilson and Monhemius, 2006; Lampinen et al., 2015). Ferric and cupric chloride leaching have been reported to have advantage over cyanidation being capable to dissolve refractory gold minerals, without pre-treatment such as pressure oxidation or roasting (Angelidis et al., 1993; Lundström et al., 2014; Marsden and House, 2006; van Meersbergen et al., 1993). According to Aylmore (2005), 4% of publications for alternative lixiviants to cyanide in gold leaching were within category oxidative chloride processes including aqua regia and acid ferric chloride leaching. Further, some patents have been granted for ferric chloride leaching of gold (Abe and Hosaka, 2010; Lundström et al., 2016)"

Jan 1, 2018

By A. D. Bas

Copper minerals present difficulties during the cyanide leaching of gold ores leading to excessively high consumption of cyanide (and oxygen) coupled with low extraction of gold. Copper cyanide species, if present at high levels, adversely affects the downstream processes such as the activated carbon adsorption and the effluent treatment. In this study, the extraction of gold from a copper-bearing gold ore by ammoniacal cyanide leaching was studied. Furthermore, ammonia leaching as a pretreatment process ahead of cyanide leaching was also examined. Only ~12% of gold was extracted by direct cyanide leaching of the ore. The addition of lead nitrate did not affect the leaching of gold. When ammoniacal cyanide leaching system was used, the extraction of gold was significantly improved to >90%. Similarly, the pretreatment of the ore by ammonia leaching was shown to lead to high gold extractions (98%), in subsequent cyanide leaching with significant reductions in the consumption of cyanide. This appeared to be linked with the ready dissolution/removal of copper during ammonia leaching.

Sep 1, 2012

By C. Raghu Kumar

Hydraulic or teetered bed separators (TBS) are finding new avenues for application in the field of mineral processing. Floatex Density Separator (FDS) is a hydraulic/teetered bed separator capable of operating at high tonnage due to its advanced instrumentation. FDS/TBS is being used in Indian mineral sand industry for classification and segregation of different minerals. The purpose of this paper is to provide details on the performance of the plant scale FDS in recovering the chromite from feed (below 1mm size). Historically this feed has been processed using hydrocyclones and spiral classifiers; however, there is a strong trend now to employ teetered bed separators, thus allowing significant changes to be made in the plant for improving process efficiency. In the present work, the performance of the plant scale FDS is described in terms of partition curve (yield, cut size, classification efficiency/Ep) for different combination of process variables and also in terms of metallurgical grade and recovery. It is found that, efficient classification can be achieved at a maximum cut size of 380 µm with and the imperfection is also reported as low as 0.16. The grade of the underflow product is enriched as maximum as 52.2% Cr2O3 from a feed assaying 40.4% Cr2O3.

Sep 1, 2012

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018

By H. J. Cao

Valuable elements could be extracted by microorganism ferment fluid from bauxite, which mainly due to bacteria acid namely organic acid. And after leaching, reclaiming the remainder organic acid in leaching solution was an important procedure for bauxite leaching process. the re-searching status about organic acid reclaiming process from bauxite ore bioleaching solution was summarized. Common processes for recycling organic acid from bauxite bioleaching solution in this period and their advantages and disadvantages, research aspects which need being confirmed for the future were Indicated

Jan 1, 2014

By L. Stamenov, H. Bouzahzah, S. Gaydardzhiev, D. Naumov

"The Chelopech epithermal arsenic bearing high-sulphidation, copper-gold deposit located in Bulgaria is often referred as the richest European gold deposit currently under exploitation. Key points from the flotation circuit of the processing plant have been sampled and selected physicochemical parameters measured. Plant survey has followed with selected samples being submitted to chemical and mineral liberation analysis (MLA). Quantitative analysis has enabled to link the flotation response of the main copper bearing minerals with the physiochemical parameters (Eh, DO, EDTA extractable Cu and Fe) being measured. Data from mineral liberation analysis have highlighted an important process-relevant information explaining the variable floatability in the various granulometric classes.The low chalcopyrite recovery could be linked to the non-sufficient amount of dissolved oxygen measured in the copper selective flotation circuit. Given the finely-disseminated copper bearing minerals, the observed copper losses inside the flotation could be also explained by the insufficient degree of liberation of the mineral grains. Suggestions for improvement in metallurgical recovery are therefore proposed.INTRODUCTIONThe Chelopech deposit is a high sulphidation (HS) volcanic-hosted epithermal gold-copper one (Bonev et al., 2002; Kouzmanov et al, 2009; Strashimirov, et al. 2002). It is considered as one of the largest and economically most important ore deposits in Bulgaria, and often is referred to Europe’s largest currently mined gold resource. It is located in the Srednogorie zone which falls within the central sector of the extensive Tethyan–Eurasian copper belt formed during Mesozoic–Cenozoic time along the southern margin of Eurasia. The Srednogorie zone has the features of a subduction-related, Late Cretaceous island arc, with development of a calk-alkaline to sub-alkaline volcano-plutonic magmatism and associated hydrothermal ore deposits (Bonev et al., 2002).Ore mineralisation occurs as veins, mineralised breccia, and massive sulphide replacements and disseminations. Three mineralisation stages have been identified at Chelopech deposit. An early pyrite–marcasite mineralisation (stage I), characterised by disseminated to massive pyrite followed and partly brecciated by enargite– luzonite and tennantite–chalcopyrite–bornite (stage II) mineralisation. The gold is met in ores belonging to the stage II. Sphalerite and galena veins characterise stage III, best developed below and adjacent to the pyrite–enargite– chalcopyrite ore bodies. Advanced argillic altered volcanoclastic rocks commonly host this mineralisation (Chambefort and R. Moritz, 2014)."

Jan 1, 2018

By M. Marinov

The Bulgarian deposits of quartz-kaolin raw materials are localized in the NE Bulgaria. For many years, the quartz-kaolin sand separation has been performing by water washing technology. After wet separation the raw material yields two products ? washed kaolin (different grades) and quartz sand (different grades). Research and development program has started to improve the quartz-kaolin sand separation. The program has undertaken an increasing of processing capacity, to decrease the losses in the tailings and to provide production of new quartz sand grades. The kaolin-silica raw materials from Vetovo open mine and the technological tailings from Vetovo processing plant were characterized. It was established that there are a lot of losses of quartz in final tailings. New approach on kaolin-silica raw material separation was tested in laboratory scale. The test work was performed on Derrick Stacksizer screening machines. The results of laboratory experiment show that there are possibilities to increase the quartz sand recovery and to start the production new grade sand. The full-scale pilot test was performed including the following units: two Derrick Stacksizer screening machines equipped with 0.430 mm and 0.150 mm opening Derrick Urethane Panel, respectively; Flat bottom DN 500 Hydrocyclone and DN 100 Hydrocyclon. The pilot test data clearly demonstrate that the Derrick Stacksizer screening machines are suitable for Bulgarian silica-kaolin raw material. Based on the test data a new quartz-kaolin separation technology was developed. The new technology was introduced in Vetovo processing plant increasing processing capacity and decreasing the losses of quartz in final tailings. Additionally the production of silica sand grade PK 0.16 is increased and starts the production a new grade PK 0.10.

Sep 1, 2012

Spent automobile catalyst is an important secondary resource of PGMs (platinum group metals) and the recovery is significant. Various methods of recovery technology have been reported and applied in practical production, including pyro- and hydrometallurgical processes. Since the grade of PGMs in the catalysts is so low, approximately 0.5 wt. %, the present recycling technologies require high energy-consumption, it is of great significance to enrich the PGMs with some energy saving physical separation methods as a pretreatment. Automobile catalyst is usually composed of cordierite phase as a substrate and alumina phase, with PGMs, which covers the cordierite phase. We adopted the quenching pretreatment, one method of thermal shock, to generate micro-cracks between the two phases and separate the alumina phase from cordierite. Quenching was carried out by heating the catalysts in an electric furnace of different temperatures followed by rapid soaking into cold water. It was found that the phase boundary between alumina and cordierite was broken in the quenching and selective separation (detachment) of alumina from the cordierite could be achieved in the following surface grinding. The effect of quenching was checked by microscopic observation, hardness measurement, and chemical analysis. This paper figures out the stress formula of the quenching process, which is largely connected with layer thickness and temperature gradient by using an FEM (Finite Element Method) simulation and clarifies the mechanism of crack generation in the quenching process. Keywords: automobile catalyst, PGM, quenching process, FEM

Sep 1, 2012

By Kazutoshi Haga, Atsushi Shibayama, Kosuke Nishioka, Yasushi Kihara, Altansukh Batnasan

The aim of this study was to investigate the feasibility studies of seawater in flotation of a 1.5 mass % of copper containing copper sulfide ore. Effects of seawater, various frothers, and different distilled water/seawater ratio on flotation of copper sulfide ore were studied. Surface properties of native copper ore and sea water soaked were examined by using FT-IR spectrometry. Chemical contents of the copper sulfide ore and after flotation were identified using XRD studies. XRD pattern showed that the main constituents of the copper sulfide ore are chalcopyrite (CuFeS2), bornite (Cu5FeS4). Flotation experiments were carried out using mechanical agitation flotation equipment with a mineral separation type flotation cell. Froth flotation experiment was conducted using calcium hydroxide was used as a pH adjuster, using methyl isobutyl carbinol (MIBC), dow froth 250 (DF 250) as frothers and potassium amyl xanthate (PAX) as collector for the copper recovery from the copper sulfide ore containing chalcopyrite and bornite. The results showed that the copper recovery by flotation was dependent on the flotation medium and frother. The main results showed that the copper recovery by flotation was dependent on the process water and frother. The copper recovery reached 97 % and 87 % in the distilled water flotation and seawater flotation with MIBC, respectively. For seawater flotation with DF 250, the Cu recovery achieved near 95 % and grade of Cu in the froth product after 5 min flotation was reached 29.8 mass %.

Jan 1, 2014

By Santiago Garcia, Dariusz Lelinski, Devan Govender, Tyson Baker, Mads Jespersen

"In recent years, the scale-up of mechanical flotation machines has been attempted with greater frequency. In contrast, the development of rotor-stator designs has been subject to greater inertia. The rotor-stator components are integral to the operation of mechanical flotation machines, responsible for the key physical processes of solids suspension, gas dispersion and energy dissipation. Design modifications are predicated upon the dual purpose of meeting customer needs while achieving metallurgical performance objectives. Accomplishing the latter is a rigorous undertaking, typically involving the sequential application of fluid dynamics principles, prototyping, smaller-scale research screening studies and larger-scale development projects. This industrial evaluation details the final stages of the forced-air rotor-stator development process using a double-refractory Carlin-type gold ore. A bypass stream of the primary rougher feed was further classified into cyclone underflow and overflow products. Four rotor-stator treatments were evaluated using parallel flotation rows coupled with a randomized statistical design. Only two treatments are compared in this initial assessment. Metallurgical responses were measured as a function of the random variation of key machine factors. Machine characterization measurements complemented the analysis of flotation performance indicators."

Jan 1, 2014

By V Radmehr

Ammonia and Amonium salts have been recognized as effective leaching agents in hydrometallurgical processes due to low toxicity and cost, easy recovery and high selective recovery of metals. New research findings of considerable advantages of leaching by these agents and elimination of problems associated with acid leaching has resulted in a new approach in the world to this method. The investigations in this field indicate more frequent use of this method for extracting copper from ore and concentrate relative to other basic metals. In this paper, we have attempted to describe the basis and different ammonia leaching methods and present the major research activities in this field for copper. We have also presented the latest findings and related novel processes. Comparative assessment of advantages and disadvantages of this method relative to acid leaching method, kinetic study of copper ammonia leaching and evaluation of Eh-pH diagrams in a system containing water and ammonia are other parts of our study. Finally, by describing the studies on copper extraction from the resulting pregnant solutions, the applicable extraction agents have been reviewed.

Sep 1, 2012

By Q. Huo

The alumina production might not continue when the sulfur content of bauxite was too high. In order to bring down the sulfur content in bauxite, we studied on the bauxite desulfurization by bacteria screened from the acid mine drainage at mines of high sulfur content. The screened bacteria were domesticated by the high sulfur content bauxite. The experiments of bauxite desulfurization were carried out under the conditions of 5% pulp density, temperature of 30?, rotate speed of 120rpm. Bacterial desulfurization for 30 days, the sulfur content of the bauxite was reduced from 5.73% to 1.55% and the desulfurization percent was 72.9%. The recovery percent of alumina was 94.3%. The study showed that it was feasible to bring down the sulfur content of bauxite by bioleaching and this technique might make full use of the low grade bauxite.

Jan 1, 2014

By B. Das

The separation of iron values from a typical Indian iron ore slimes containing 57.2% Fe, 5.81% SiO2 and 7.05% Al2O3 by wet magnetic separation and selective magnetic coating is investigated. The iron phases, which are mostly paramagnetic in nature, have been coated with magnetite or colloidal magnetite in presence of surfactant by manipulating the surface properties of the minerals. The studies have indicated that an iron concentrate containing 62.32% Fe with 66.5% iron recovery can be obtained at medium magnetic intensity of 7.8 kG which is much less compared to normal magnetic intensity of 13 kG to14 kG required for hematite-goethite separation. The performance of this technique with respect to both grade and recovery is superior to conventional magnetic separation or flotation of iron ore slimes.

Jan 1, 2014

"This research aims at improving the beneficiation of coals and minerals in fine and ultrafine size fractions. A widely used method for upgrading fine and ultrafine particles is froth flotation, which is generally classified into mechanical flotation and column flotation. The present work is focussed on column flotation. A flotation column equipped with a conventional bubble diffuser/sparger was used with oscillatory air supply generated using a fast-switching solenoid valve. The flotation tests were carried out for coal particles and mineral particles, respectively, and a comparison in flotation performance was made between oscillatory air supply and steady air supply. It was found that use of oscillatory air supply with a proper valve switching frequency and on/off time ratio to replace steady air supply could lead to increased recovery of coals or minerals by more than 14 percentage points and substantial reagent cost savings. The improved flotation performance was attributed to enhanced gas dispersion and flow conditions. This research offers a simple new approach to improving the beneficiation of fine coals and minerals with using flotation columns.INTRODUCTIONFroth flotation has been widely used for the separation and concentration of fine coals and minerals by exploiting the difference in their affinity to air bubbles in aqueous medium. Froth flotation is an effective method for beneficiation of coal and mineral particles in a certain size range. It remains difficult to upgrade ultrafine mineral particles. One of the reasons for the ineffective flotation of fine particles is the low probability of bubble-particle collision in the collection zone (i.e., the pulp zone). According to Reay and Ratcliff (1973) and Yoon and Luttrell (1989), the probability of collision is significantly affected by bubble size and particle size, and the collection zone recovery can be increased by decreasing the bubble size."

Jan 1, 2018

By T. M. Bhatti

The main purpose of present study was to characterize the dissolution of uranium from low-grade black shale with indigenous isolated strain of Acidithiobacillus ferrooxidans (BSAF-01). The nature of shale is quartzite-schistose and contains uranium content of 0.005% U3O8 (50 ppm U3O8). Uranium is present in the tetravalent oxidation state (U4+) in the shale matrix. The main minerals identified are graphite, quartz, pyrite, mica minerals (phlogopite, biotite, sericite, and chlorite), microcline, K-feldspar and kerogen (hydrocarbon-compounds). Bacterial oxidation of pyrite was an acid-generating system and produced sulfuric acid and ferric sulfate during this biological phenomenon. A series of bioleaching experiments were conducted in shake flasks for leaching of uranium from black shale. The leaching experiments were performed at 50% pulp density using indigenous Fe- and S-oxidizing bacterium (Acidithiobacillus ferrooxidans). Bioleaching data revealed that about 90% ~ 95% U3O8 was leached out from black shale ore. Uranium dissolution from shale depends on pH (pH 1.5~1.9), redox potential (=500 mev) and the concentration of Fe2+ and Fe3+ ions in the leaching environment. The oxidative leaching of U4+ involves a redox reaction with Fe3+ as an oxidant and bacterial re-oxidation of Fe2+ in acidic leaching environment. Uranium leaching efficiency was attributed to the sulfuric acid and ferric sulfate production during bacterial oxidation of pyrite.

Jan 1, 2014

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012