Search Documents

By Priyanka Dhar, Kurt Aasly, Hanumantha Rao Kota, Hassan Bouzahzah, Maria Thornhill

The interest in investigating the processing characteristics of mineral deposits in Norway has seen an upsurge in the last decade. One of the major areas of interest is a huge copper deposit, operated by NUSSIR ASA located in the Repparfjord Tectonic Window in the caledonides of west Finnmark. This study reports analysis of ore from the deposit for development and modifications in the flotation flowsheet for the NUSSIR ASA copper ore. The mineralogical characterization for the ore sample was achived by optical microscopy and Zeiss automated mineralogy while grinding characteristics were tested using Bond Index tests. The results confirmed the presence of Cu minerals in the form of chalcocite, chalcopyrite and bornite in the samples, which are mainly liberated in the – 105 µm size range. The majority of non-liberated copper sulphides associated with silica and the carbonates varies from 3 to 28 percent in the –250 µm samples . It is also observed that the copper minerals are uniformly distributed in all size ranges. Selective flotation of NUSSIR copper ore was performed in different size fractions with a motive to identify the correct liberation size and thus to obtain a copper concentrate meeting the quality requirements. The flotation experiments are essentially performed in two stages: the rougher and the cleaner stage. Mass balance calculations were performed showing that approximately 88 percent of copper can be obtained at the end of the process. Ultimately, overall circuit copper recoveries ranged between 83.5 to 88.1 % with a concentrate grade of 35 to 48 % Cu.

Jan 1, 2018

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

By S. P. Nagaeva, A. V. Kuptcova, O. Yu. Poperechnikova

"The present paper contains study results of gold morphology and grain size distribution in flotation concentrates produced from original ore samples from deposits of different genesis. Pre-concentration methods were used with selective dissolution of rock minerals and mineral heavy medium separation to obtain statistically valid data on gold grain size and morphology in concentration products. Special attention is given to study of flash flotation concentrates that is mainly used for coarse gold, underextracted in gravity circuit. Analysis of geometrical optics has allowed to establish that during flash flotation gold grains more than 150 µm can be extracted from 10 to 35%, and in some cases single gold grains above 300 µm. INTRODUCTION Distinctive features of gold that have a significant impact, and in some cases, decisive influence on its recovery into saleable products are mineral shape, grain size and morphology of metal particles, paragenetic associations of gold. Peculiar feature of coarse gold is its easy extraction during grinding from associated mineral components like quartz, sulphide and other and almost complete recovery into gravity concentrates (Lodeischikov V.V., 1997). Morphology of native gold is so diverse that different gold grains are better extracted using different methods of concentration. Compacted and rounded particles are easily processed using gravity concentration but low cyanidable and hard to process using flotation. On the contrary, lamellar, flake, dendrite and capillary aggregates of high specific surface are easily cyanidable and under definite conditions it has strong floatability (Lodeischikov V.V., 1997). Flotation of gold-containing sulphide minerals and free gold takes place simultaneously during flotation concentration. In case of low-sulphide ores, native gold takes the basic load, having the high density (15.6 to 18.3 g/cm3, for pure gold – 19.3 g/cm3) it has limited size and morphology for successful flotation. It is known that flake gold and fine-grained gold up to 0.1 mm are easily extracted (Lodeischikov V.V., 1997). Authors of the present paper performed a study of gold granulometry and morphology in flotation concentrates produced from gold-containing ores from two deposits of different types: gold-copper oxidized hematite ores and low-sulphide gold-quartz ores. Ores are different by both host rock composition, mineralogical and petrographic features, gold grade in mineral assemblage and morphology and size of precious metal. Common for both ore types is low-sulphide content and presence of free gold."

Jan 1, 2018

By G. Bulut, Ü. Yenial

"Heavy metals contamination in aqueous systems can be found in a variety of industries, in particularly mining, metal processing, finishing and plating. Water containing more than 0.5 ppm heavy metal considered as a toxic due to harmful effects on health. The major techniques employed for heavy metal removal from industrial wastewaters include precipitation, reduction, ion-exchange, and adsorption. Adsorption is a heavy metal removal method for aqueous systems. As a common adsorbent, activated carbon has been used in treatment but it is ineffective on some elements. Thus, there has been a research for developing highly effective and selective adsorbents. In this study the adsorption of lead and arsenic ions on to coal waste and red mud waste was studied. The experimental parameters were determined as pH, equilibrium time and the initial concentrations, activation by heat treatment and the blend of adsorbents. According to their adsorption capabilities, red mud was found to adsorb lead and arsenic ion with high efficiency but coal waste did not adsorb arsenic ion. However the binary adsorptions of these ions were enhanced the adsorption efficiencies. In addition the blend of coal waste and red mud affected the adsorption efficiency. INTRODUCTION As a result of rapidly developing industry and excessive use of water resources, the need of clean water and wastewater management appear as a problem. Wastewater recycling activities and researches come to the fore for an effective use of wastewater. Recycling of wastewater, which contains heavy metals harmful to the environment and human, is a difficult process. Heavy metals are generally divided into three categories: toxic metals, precious metals, radionuclides. Wastewaters from various industries, containing heavy metals, are the main polluters of water and soil. Although their toxic structures, heavy metals are used extensively in industry as they have technological significance. Usually mining industry, metal industry and industrial organizations produce heavy metal containing wastewaters (Volesky 1990, Ting and Lawson 1991, Bishop 2002)."

Jan 1, 2018

By Luo Chuansheng, Rao Jinshan, He Xiaojuan, Qiu Xianyang

The dissemination grain size of chalcopyrite is really fine and refractory grains of -10µm take up 25%. Dissemination relationships among chalcopyrite with pyrrhotite, pyrite, marcasite and gangue minerals are complex. Content of Fe-bearing sulphides and Fe-bearing silicates associated with chalcopyrite reaches to about 60%. It’s hard to liberate and separate chalcopyrite from pyrrhotite. The above four are the main mineral processing difficulties of a copper ore in China. Because of the similar floatability and poor separation effect between chalcopyrite and pyrrhotite, enhanced depressing and collecting method was adopted in Cu-S separation before 2009. Due to the different magnetism among chalcopyrite, pyrrhotite and Fe-bearing silicates, magnetic separation is creatively induced in Cu floatation circuit based on the in-depth study of process mineralogy. High efficiency and new Cu-S separation technology of "Rough concentrate regrinding-pyrrhotite rejecting from middling by magnetic separation" and a highly selective copper minerals collector YL-1 had been developed to solve the difficult problems of refractory Cu-S separation, which are heavy load of middling recirculation,difficulty in upgrading Cu concentrate, unstable locked cycle and low separation indexes. And grade of Cu concentrate has been increased by 3.33%, recovery of Cu and Ag has been increased by 19.32% and 10% respectively.

Jan 1, 2014

By Ataollah Nosrati

Agglomeration of fine mineral particles is an important step in heap leaching processes employed for a cost-effective hydrometallurgical extraction of value metals from low-grade ores. In this study, the effect of acidic binder composition and feed ore particle size on binder dosage requirement and isothermal, batch agglomeration behavior of siliceous goethite nickel laterite has been investigated. Agglomeration tests performed with tap water and 30, 44 and 98% w/w H2SO4 solutions as binders revealed the key role of binder formulation in controlling ore particle wettability, nucleation and granule growth behavior. Both lower binder acid content and higher dosage led to greater wetting, nucleation and granule growth rates. Variation of feed ore fine/coarse particles? mass ratio dramatically impacted on binder dosage requirement for effective particle wetting, nucleation, and growth agglomeration behavior. Increasing fine (-150 µm) fraction mass content in a -2 mm feed ore, led to higher binder dosage requirement and enhanced nucleation, however the overall agglomeration rate/granule size growth decreased. In contrast, the presence of coarse (5 ? 15 mm) particles in feed ore led to (i) lower binder dosage requirement, (ii) enhanced initial agglomerate size growth rate, and (iii) reduced coalescence. For dry agglomerates of similar sizes, competent coarser feed particles led to remarkably higher compressive strength than did finer feed particles. Microstructure analyses indicated that the granules containing coarser particles exhibited a distinctive, competent core/shell (fines) structure which led to their structural reinforcement. The appropriation of the findings for optimizing agglomeration behavior for enhanced heap leaching of complex, low grade laterite ores are discussed in this context.

Sep 1, 2012

By Y. Posedko Eugene, S. S. Gudkov, Yu. E. Emelyanov, A. V. Bogorodsky, A. V. Boldyrev, S. V. Balikov

"The article presents the results of precious metals leaching using halogen solvents and their precipitation on a sorbent in the process of pressure oxidation. A technology of pressure oxidation – carbon-in-leach treatment (POX-CIL) of refractory sulphide gold-bearing flotation concentrates with the addition of a halogen solvent and a sorbent was developed based on the laboratory studies and pilot plant tests. The technology involves the following steps: oxidation of a flotation concentrate; precious metals dissolution and recovery on a sorbent; precious metals elution; electrolysis of eluates; smelting of cathode precipitates with producing Dore beads. This approach ensures oxidation at least 98% of sulphides and gold of more than 95%. The POX-CIL process have the following patents: a patent of the Eurasian Patent Organization No.017438 “A method of processing materials containing precious metals and sulphides” and a patent of the Russian Federation No.2625146 “A method of precious metals recovery from refractory sulphide gold-bearing materials”.INTRODUCTION Gold-bearing ores are classified as readily amenable to cyanidation, or non-refractory, and not readily amenable to cyanidation, or refractory [1]. Special attention should be given to the three most common technological types of gold-bearing ore materials, according to the Irgiredmet’s classification: pyrite-arsenopyrite ores with finely disseminated gold locked in sulphides (physical depression of gold in cyanidation process); cupriferous gold-bearing ores, when cyanidation comes along with chemical depression of gold by mineral compounds (cyanisides); carbonaceous ores showing higher sorption activity to precious metals dissolved in cyanide. Direct cyanidation of refractory sulphide gold-bearing materials does not provide high recovery of precious metals. There are the following methods of refractory gold-bearing ores and concentrates preparation to subsequent gold recovery: roasting, fine grinding, bacterial and pressure oxidation (POX) [2]. Existing POX-cyanidation flowsheets involve high costs due to a large amount of process operations and using expensive and environmentally hazardous sodium cyanide."

Jan 1, 2018

By A. Koizhanova

Kumistinskoye gold- and silver bearing ores (Republic of Kazakhstan) as well as standardized test solutions containing gold, silver, copper, zinc and iron were studied. The best results in silver and gold recovery from Kumistinskoye gold- and silver bearing ores were achieved through use of complex cyanide-thiosulfate solutions as compared to individual cyanide solutions and thiosulfate solutions. It was found that such complex solutions substantially step up leaching process herewith increasing precious metals recovery rates. Thermodynamics of studied chemical processes was calculated. Reaction order, kinetic constant and activation energy of gold leaching process through use of cyanide-thiosulfate solutions were identified. We managed to prove that the sorption rates and holding capacity in process of gold anions recovery with anionite AM-2B are comparable to sorption characteristics for cyanide solutions. Keywords: gold, silver, copper, zinc, iron, cyanide-thiosulfate solutions, anionite AM-2B

Sep 1, 2012

By A. V. Zimin

It is a well-known fact that usage of reverse cationic flotation in magnetite ores processing enables to improve the quality of magnetite concentrates. We designed an iron ore concentrate technology (with 70 -71 % of iron) including reverse cationic flotation in pneumo-mechanical flotators RIF (developed by RIVS Corporation, Russia) with good biodegradable etheramines as collectors for flotation of quartz. Practical application of high biodegradable flotation reagents decreases environmental impact risk of objects and enterprises of mining industrial complex. This work presents results of development of flotation technology for production of high quality ferruginous concentrates from magnetite ores of Russia and Ukraine deposits. Keywords: magnetite ores, reverse cationic flotation, ferruginous concentrates, pneumatic-mechanical flotation machines, environmental impact

Sep 1, 2012

By K. D’Elia, L. D. Ogrel, O. A. Malyshev, T. I. Yushina, I. M. Petrov

"The purpose of this research is to develop enhancements in the mineral processing by flotation methods of nonferrous ores. Currently, 180-190 million tons of ore are processed by flotation in Russia. The annual processing volume of copper-nickel and copper-zinc ores exceeds 20 million tons. In the total volume of processed ores by flotation, non-ferrous ores account for roughly 35% and ores of precious metals for another 15%. The total demand of flotation reagents in Russia in 2016 was estimated at 170,000 tons. Sulfur-based collectors used in the flotation of non-ferrous sulfide ores (typically, xanthates) do not always offer sufficiently high recovery of valuable components.It has been found that reagents like DMIPEC and DK-80 improve the recovery of metals into concentrates. To identify the reasons of that higher recovery, quantum chemical calculations of the mechanism and interaction forces of DMIPEC with non-ferrous sulfides were undertaken by determining the stabilization energy of the resulting chemical complexes. It has been shown that, in the interaction of DMIPEC and DK-80 with the surfaces of sulfide minerals, ethylene and acetylene bonds act as the reaction centers, and the formation of molecular p-complexes is the result of metal-cation interactions with the surface and the flotation reagents.In the flotation of non-ferrous ores, DMIPEC and DK-80 act as selective supplementary collectors with foaming properties, and at a flow rate of 3-35 g/ton, they reduce the flotation time, and increase copper recovery by up to 3.5%, zinc recovery by up to 12%, gold recovery by up to 8-10%, allowing to increase the recovery of valuable components by 1.5-12.0%, basically this kind of reagents nearly double the flotation rate, improve the grade of the concentrate, improve the stability of the flotation process parameters, and reduce the environmental impact of flotation plants."

Jan 1, 2018

By V. E. Dementiev, V. I. Kulikov, G. I. Voiloshnikov, Yu. O. Fedorov

"The report presents the summary of the JSC Irgiredmet’s activities in the field of preconcentration of ores. As of 2018, the Institute has almost 40-years’ experience in this area. Over the years, Irgiredmet has done a lot of work – from development to implementation of new technologies of ore piece sorting and concentration based on X-ray radiometric separation (XRRS). INTRODUCTION Preconcentration has been a challenging issue of the mining industry over the last decades. The implementation of this technology can significantly increase mining efficiency. The main application of preconcentration is improvement of mined ores quality, however new and more complex issues have arisen with the evolution of the technology. Irgiredmet has started to develop an efficient preconcentration technology for gold-bearing and rare-metal ores 40 years ago. The X-ray radiometric method widely used at that date as a method of elements determination in geology and geophysics become the ground for this work (1). Since that time, the Irgiredmet Institute has developed and significantly improved the technology of piece ore sorting, or XRRS (2-5), that is currently also known as the X-ray fluorescence method. The progress of the XRRS development achieved by Irgiredmet in cooperation with Rados LLC, Tekhnoros LLC (Krasnoyarsk), Rados-Service LLC and CJSC Tekhnogen (Ekaterinburg) has proved efficiency and applicability of the XRRS technology for processing a wide range of minerals and solving of various technological problems (7-9) compared to other radiometric methods (6). Furthermore, obtained results are supported by numerous studies, trials and implementations. The significance of ore preconcentration for greenfield and brownfield projects determined the establishing a new subdivision of Irgiredmet, the XRRS Technology Center (XRRS TC), that has provided the Institute with a completed range of processing technologies, from preconcentration to producing final products. Over the past few years, the XRRS Technology Center has carried out studies and testing of a numerous (more than 100) projects, mines and deposits of gold-bearing ores, rare metal ores (Be, Ta, Nb, W, Mo), base metal ores (Cu, Sb, Zn, Pb), ferrous metal ores (Fe, Ti, Cr), rough diamonds and coal. The XRRS Technology Center performs various specific studies and testing not only in Russia, but as well as in Kazakhstan, Georgia and Mongolia. Mines and companies from Chile, India, China, Iran and other countries also take an active interest in the XRRS technology."

Jan 1, 2018

By Kevin Davey, Liza Forbes, Leanne Smith

Given the global scarcity and value of potable water, interest in the use of water of lower quality in mineral processing has grown significantly in recent years. Previous laboratory batch flotation tests conducted at CSIRO have shown that chalcopyrite floats strongly without collector in distilled water and that the collectorless flotability of chalcopyrite is unaffected by the use of brackish water, sea water or hypersaline water. In contrast, bornite is moderately flotable without collector in distilled water but all three lower-quality waters have a detrimental effect on the recovery of bornite. The depressant effect is so strong that the little recovery achieved in these waters was only slightly above what might have been expected from entrainment alone. This work has now been extended to another important copper sulfide mineral, chalcocite. In contrast to chalcopyrite and bornite, chalcocite does not exhibit collectorless flotability so the chalcocite tests in this study were performed in the presence of a standard collector (potassium ethyl xanthate). The results reveal that chalcocite is flotable with xanthate in distilled water but the lower-quality waters have a detrimental effect on the recovery of chalcocite. This effect is partly reversed by increase collector additions. Further tests were completed in order to investigate the effect of the different ions present in the saline waters on chalcocite flotation. Possible reasons for the observed differences are discussed in terms of the pulp chemistry of the system.

Jan 1, 2014

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed. The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters. A good correlation between flotation, adsorption and surface energy as a function of amine concentration and pH was observed. The sudden increase in wollastonite flotation and amine adsorption at and above 5x10-5 M initial amine concentration is thought to be due to two-dimensional precipitation of amine on surface in accordance with the recent 2D-3D precipitation model of amine adsorption on silicate minerals.

Jan 1, 2003

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By E. V. Zelinskaya

"Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production. Considerable attention in recent decades has been given to waste recycling. The task is to maximize the use of both newly formed and accumulated solid and liquid wastes. The mining and mining and smelting enterprises industrial waters are a very promising source of secondary hydromineralic raw materials. They have high concentrations of not only calcium, sodium, but also, for example, lithium, rubidium, heavy non-ferrous metals. In general, unfortunately, we have to state that today there is no wide practice of extracting valuable components from waste enrichment, as well as processing of man-made waters to extract metals from them. The quantity of extracted components from underground, and furthermore passing waters, is insignificant. At the same time there is a tendency to increased demand for rare metals: Sr, B, Br, I. This is explained by their wide use in many industries. For example, the consumption of lithium products is steadily increasing. The obtained results showed that in the liquid phase in connection with high salt content and a significant difference in the macro- and microcomponents contents, conditions are initially created for the microcomponents selective isolation possibility. The identified conditions realization is most possible in such technological processes as cryotechnology, sorption and ion flotation. There is an urgent need to expand research in this direction and to recognize as a publicly important task the mining and industrial waste processing full-scale introduction into the practice of operating mining and processing enterprises and iron and steel companies.INTRODUCTION Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production."

Jan 1, 2018

By Ata Akcil, Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

Phosphorus slag is one of the most large-tonnage of yellow phosphorus production waste, which for decades stored in the slag disposal, by polluting the environment and creating environmental problems in the regions. Phosphorus slags from the processing of Karatau phosphorites are a very promising source of raw materials not only for silicon compounds but also rare earth metals (REM). Among the REM, yttrium, neodymium, europium and lutetium predominate, which are relevant to high-tech industries. The report presents technological scheme of complex processing of slags of phosphoric production with obtaining of REM concentrate and precipitated silicon dioxide ("white soot"). The regime parameters of the main operations of the technology are determined: I stage- leaching of slag with nitric acid solution; extraction of the REM-containing solution with tributyl phosphate and stripping of the REM with water; settling of solution of salts of oxalic acid, calcining the precipitate to obtain a concentrate S REM oxides and II stage of leaching silicon cake to obtain "white soot". Recovery of S REM from slags of phosphoric production on various redistribution has made, %: leaching – 95.0; extraction - 90.2; extraction on the average ~ 93.2; the production of a concentrate of REM oxide is 93.9. A concentrate containing 17.3 % of REM oxides was obtained. According to X-ray analysis it contains the following phases: calcium oxide, portlandite2, gadolinium oxide and yttrium, gadolinium oxide, gadolinium oxide and cerium, neodymium oxide, neodymium oxide and cerium. Thus, the concentrate can serve as a raw material for the production of individual rare-earth metals like gadolinium, cerium, yttrium and neodymium. After performing the II stage of leaching siliceous cake with nitric acid the samples of "white soot" were obtained. Its chemical composition corresponds to the state standard and has a specific surface area equal to 180 - 200 m2/g. The technology has been tested in a large-scale laboratory scale and will solve the problem of complex processing of phosphorus raw materials and import substitution in Kazakhstan. The end-to-end recovery of S REM oxides and silicon into concentrate and product from their initial content in slags is ~ 75.0 and 98.0 %, respectively.

Jan 1, 2018

There are some problems in the beneficiation of fine-grained oxidized iron mineral such as high cost, severe sliming, poor results and low recovery due to the fine disseminated size of the mineral. Taking several representative types of finely-disseminated oxidized iron minerals as examples, the author analyzed the main difficulties in the beneficiation of such kind of ores and discussed the existing problems in grinding-classification, technological process, flotation reagents and separation equipments and the resolvents of these problems.

Jan 1, 2014

By Hristo Stanchev, Veselin Mehandzhiyski, Sashka Kozhuharova, Stefan Stamenov, Alexandar Penchev, Nikolay Nestorov, Velika Stamatova, Ekaterina Todorova

"This article presents the results of comprehensive research on the quantitative distribution of gold content in the raw ore and tailings from the flotation enrichment process at the Ellatzite Med plant. The study is a quantitative and qualitative determination of the presence of gold in the ore processed by Ellatzite Med AD, as well as its behavior and distribution in the various metallurgical products of the flotation process. The representativeness of the samples taken is ensured by the frequency of sampling: four work shifts of sampling on different days within a period of four consecutive weeks. The form of gold present is determined both in the analyzed samples and in separate fractions - granulometric, magnetic, electromagnetic, heavy and light. A summarized diagram presents the phase distribution of gold in the final products of the dressing process. The results obtained are used for further analysis and evaluation of the actual technological parameters of the gold. It was established that an increase in the initial gold content, respectively in the content of native gold in the raw ore, with the current process, leads to an increase in gold losses, mostly in the native gold phase. The conducted analysis of the results from the comprehensive tests on determining the form of gold present in the various enrichment products gave rise to further research with the use of a Knelson centrifugal concentrator."

Jan 1, 2014

By Sydney Mantsho, Toni Streczynski, Manuel Gonzalez

"In 2013, the commissioning of the MillStar Stabilisation and FloatStar Stabilisation and Optimisation controllers were completed at the Cerro Bayo Silver (Ag) mine in Patagonia, Chile. The MillStar control system has stabilised the feed to the SAG mill as well as the density at the discharge end of the SAG mill and ball mill. The FloatStar Stabilisation and Optimisation controllers have successfully stabilised and optimised the flotation circuit to ensure consistent product quality within desired specifications.The mill feed is controlled utilising the MillStar Solids Feed controller. Additionally, the solids to liquid ratio into the SAG mill was controlled utilising the Mill Inlet Ratio controller in conjunction with the Solids Feed controller. The discharge end of the milling process is a highly interactive and complex system. The use of a Robust Nonlinear Model Predicative Controller (RNMPC) was ideally suited to control this section of the process. On the Cerro Bayo milling circuit, the RNMPC was used to control the mill discharge sump level and the primary cyclone feed density to produce a more consistent feed to the flotation circuit.Three levels of the FloatStar control system were installed, for flotation stability, concentrate flow stability as well as grade optimisation. The Level Stabiliser was used to stabilise the level control on 6 flotation banks. The Flow Optimiser was commissioned on the Rougher, Scavenger and Cleaner concentrate sumps to stabilise concentrate flow from the flotation cells. The Grade Recovery Optimiser was commissioned on the Roughers section. A number of instrumentation challenges were identified which limited the overall benefit derived from the system. Once these were addressed, the performance was optimised. The overall benefit provided by the system was observed in terms of the improvements in Ag recovery."

Jan 1, 2014

By Victor Avdokhin, Ivan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation.Catching coat is formed of natural magnetic and weak-magnetic placer minerals in field of magnetic system of the sluice. Magnetic minerals, placing along magnetic lines of force, form rough coat of fluffy structure. Size of the magnetic particles is chosen taking into account expected size of gold particles, which are to be fixed on the rough coat or between the magnetic particles. Changing coarseness of particles of mineral bed allows to regulate selectivity of recovering heavy minerals.Forming artificial fleece from magnetic minerals of initial sand, increasing capacity of the bed and relative hydraulic proportionality of mineral particles of the bed provide for the most effective recovery of fine gold."

Jan 1, 2003