Search Documents

By Ashish Agarwal

For a correct evaluation of the performance of any process, it is important to reconcile the data gathered in the plant from the material balance point of view for all the streams flowing in and flowing out of the process unit. There are two main approaches to reconciliation of data, which involve minimization of the sum of the squares of: (i) the closure residuals and (ii) the component adjustments; both weighed with the estimated variances of the components. Though, these approaches have served us well, it has not been possible to ascertain if the reconciled values for various components and the split factors obtained using these approaches are truly the best estimates. In this paper, this aspect has been investigated by analyzing pseudo-experimental data of known error structure on size classification of particles in a hydrocyclone. Three types of basic error structures were considered for the measured component values: absolute error, relative error and chi-square error. The error structure was modified by adding a random component of error using normally distributed random numbers corresponding to zero mean and different levels of variance. By carrying out a large number of simulation experiments, it has been shown that in the presence of random errors, irrespective of the basic error structure of data, which is usually unknown, the chi-square error minimization criterion can be used to obtain most reliable results. Keywords: data reconciliation methods, chi-square error minimization

Sep 1, 2012

By J. C. Wilmot

The chemistry of aqueous cyanide containing species in the presence of reduced sulfur sources was investigated. Reactions were studied as a function of time and tracked using novel analytical techniques developed for the analysis of the species of interest in the sample matrix. Species of interest in this work were ?free? cyanide, thiocyanate, cyanate, metallo-complexed cyanide, and various sulfur and sulfur-oxygen species. The studies were conducted under constant temperature conditions at pH values above 10.5 and in the absence of light in order to eliminate photochemically induced cyanide reaction effects. The reaction products of cyanide when in contact with pure sulfur, pyrite, pyrrhotite, sphalerite, and cinnabar are reported. These data combined with data for cop-per, arsenic and lead sulfides, which have been previously published, are used to predict the fate of cyanides in refractory gold ores containing sulfides. A mass balance on the cyanide reaction products was completed for all experiments. From these studies insight into the chemical relationships of cyanide, the specific metal sulfide, thiocyanate and cyanate have been gained. When looking at the results of the experiments, it was immediately apparent that even though the overall conversions of cyanide to thiocyanate were different, most of the samples exhibited a similar pattern of reactions. The recovery of cyanide in these experiments was better than we expected, averaging in most experiments to be over 90 percent. Based on this research, the formation of cyanate was probably the main route of loss. The pathway choice for the various minerals was also elucidated in these experiments. The competitive oxidation pathways that cyanide can take have been tracked for sufficient time to determine the ?final? fate of cyanide in a process. Initially, it was thought that the cyanate may be involved in a hydrolysis reaction to form ammo-nia and carbonate ion, but upon further inspection of the data, there was not the drop-off in total cyanide recovery that would manifest itself were this to happen. On the other hand, the hydrolysis of thiocyanate to cyanate and sulfate would require oxidizing conditions which did not exist in solution at the beginning of the experiment. If the solutions were to be sufficiently oxidizing in nature for this to happen, the initial amount of cyanide would have been converted to cyanate quickly. The data support premise that the ?hydrolysis? of thiocyanate to cyanate and sulfate occurs to some extent in the experiments conducted. Knowledge gained from the experiments with pure metal sulfides helped interpret the results of experiments with refractory ores found in the State of Nevada.

Jan 1, 2014

By Mario Gerards, Marco Steinberg, Jan Huben

"Wet high intensity magnetic separation or WHIMS is a widely used technical process for the recovery of magnetic susceptible iron ore particles, mostly for fine and ultrafine grain sizes. The JONES® WHIMS - Wet High Intensity Magnetic Separator, has been used for many years and in countries all around the world. This paper outlines the physical principles utilized for the separation inside the unit, as well as some of the recent changes and developments on the design. It will also give an outlook on the theoretical potential of different alternative yoke materials. The aim of this paper is to analyse the suitability of different yoke materials to improve the equipment. This will be done comparing the magnetic and mechanical parameters and analysing availability and price to find the best compromise regarding cost and benefit. As far as the different kinds of materials are concerned, a special material has been identified as suitable during the comparison exercise. After running the economical calculations, especially with respect to the reduction of the total power consumption of the equipment, a tremendous reduction of the total power consumption has been determined. In addition, to the theoretical exercises and due to the promising results of the same, the Pilot Unit P 40 of the JONES® WHIMS has been manufactured with the special material in order to get practical results as well. Finally, this paper outlines the theoretical and practical results focused on the power consumption. The results are showing that the total power consumption can be reduced tremendously. Hence, the way for a new generation of JONES® WHIMS - environmentally friendly - has been paved."

Jan 1, 2014

By J. Leite

In a small-scale mining in Brazil?s northeast, scheelite were exploited since 1940?s using a traditional gravity concentration flowchart (composed by jigs and shacking tables) that operates with low efficient for fine particles. Tailing of this plant was submitted to chemical, mineralogical and size characterization. Results pointed 50% smaller than 74µm with a grade of 0.11% WO3. The particle?s size is an important operational variable to heighten recuperation by shacking tables. Tests using Falcon SB40 centrifuge concentrators and shacking table were realized, optimizing their operational variables. Based on the tests results a new flowchart was proposed for concentrating and tailings recovery.

Sep 1, 2012

By Janne Kauppi, Kaj Jansson, Piia Suvio, Saara Hagnäs

"Historically the focus at the mineral processing sites has been to improve the production operations, while little focus has been set on how factors, such as the quality of water used in the process affects the metal recovery. Simultaneously increasing public pressure and water scarcity is driving the mining industry to recycle more water back to the process, which in turn leads to accumulation of impurities within the recycled water. This paper presents a concept for a systematic approach on targeting the impurities that have a negative effect on the metal recovery at the flotation circuit by using a novel solution called Process Water Recycling Plant (PWRP). These plants are designed with specific ore type in mind. PWRP produces cost-effectively process water to different target qualities, especially for flotation purposes enabling higher and more stable flotation recovery. It consists of pre-designed and standard water treatment units for a wide range of volumes. The application-specific configuration of units is governed by the water quality requirements, and can be designed according to specific customer needs. Testing has been carried out in order to investigate, which recycling water impurities affect the different ore types and how the metal recovery in flotation is affected as a consequence of the poor-quality water. The results indicate that every ore type is impacted differently and without a good understanding on how the water quality impacts the process performance, adverse effects on the flotation recovery can occur.INTRODUCTION With a focus on where water is used within the mineral processing, it has become evident that even though water is used in several different processes, majority of the water losses within the site occur at the tailings processing and the tailings storage facility. New tailings management technologies that can increase the recovery of water are actively being developed, but the key to improving the efficiency of water use and reducing the operational risks lies in closing the water loops and increasing the slurry density in the tailings processing. With this shift from conventional tailings technologies towards paste and dry stacking, water efficiency is vastly improved, but it might in turn lead to process water challenges with impurities, reagents and fines being recycled and accumulated within the production processes."

Jan 1, 2018

By de Vaux. D.

Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis. The results obtained have demonstrated that water quality does play a significant role in flotation recovery at the experimental conditions used.

Jan 1, 2003

By N. Schreithofer

Varying flow regimes, particle populations and consequently different types of bubble-particle interactions characterize the different zones of a flotation cell. The understanding of the role of the different zones of turbulent intensity on the particle-bubble interactions is of primary importance to optimization and scale-up of flotation processes and machinery. In order to study particle-bubble interaction in turbulent flow a completely new approach was taken. A laboratory scale stationary turbulence device was developed and built. The set-up allows the observation of particle-bubble interactions in various turbulence intensities, particle and bubble sizes and surfactant concentrations. The experimental set-up consists of a transparent, specially designed tank in which liquid flows between carefully designed and placed obstacles that create different turbulent flow fields. Bubble-particle aggregates are introduced into this turbulent zone. The behaviour of the aggregates, such as attachment /detachment of particles to/from air bubbles is recorded by a High Speed Imaging (HSI) system (5400 fps). The images are then analysed and the dependence of attachment/detachment process is described as a function of turbulent intensity in different conditions for different surfactant concentrations. This paper introduces this method to study particle-bubble interactions in turbulent flow and correlation to Computational Fluid Dynamics (CFD) simulation. CFD modelling is validated for two and three phase systems; liquid-gas with liquid and solid tracers respectively. The CFD simulations using the RANS k-S turbulence model showed good correlation to the experimental data and the experimental method is a promising tool for investigation of particle-bubble interaction in turbulent flow.

Jan 1, 2014

By R. J. Batterham

The science and practice of mineral processing has been driven for many years by the same set of challenges that shape the mining industry ? demand and supply, grades and their decline with time, mineralogy and the need to handle more complex ores, disposal and minimising of wastes and the availability of water, power, skilled labour and the like together with increasing expectations from the community, concerns on sustainability and safety and, as well, climate change forcing a more targeted approach on energy. In this paper, the author builds on previous reviews to the IMPC and suggests that while step changes are long overdue, the unprecedented demand mitigates against drastic changes. That said, the ?Mine of the Future? is already requiring some different approaches.

Jan 1, 2014

By Hiroshi Sasaki, Herman D. Mendoza

"The surface-chemical property of nickel slag fiber was modified in aqueous media in order to act as an active and efficient collector of colloidal amorphous silica from geothermal effluent. Colloidal amorphous silica (0.05 µm) from geothermal wastewater causes operational and ecological problems. It clogs geothermal pipes and waterways, and when disposed to the environment poses hazardous effects on both the flora and fauna ecology. Because colloidal amorphous silica is extremely fine and remains in suspension in aqueous media, conventional solid/liquid processes to remove colloidal silica from its bulk liquid are rendered ineffective.A rapid separation technique is then developed to remove effectively amorphous colloidal silica from its bulk liquid by attaching the extremely fine particles of silica onto a nickel slag fiber coated with magnesium hydroxide, Mg(OH)2. The nickel slag fiber has the following characteristics: a high surface area and predominantly possesses negative charge in aqueous media with an iso-electric point at pH ~2.5. When soaked and saturated with Mg(OH)2 solution, the surface of the nickel slag fiber becomes coated with fine and compacted Mg(OH)2 precipitates. This modifies the surface- chemical property of nickel slag fiber transforming the negatively charged surface into a positively charged surface in aqueous media with an iso-electric point of around pH 11.8, which corresponds to the iso-electric point of Mg(OH)2. When geothermal effluent containing negatively charged colloidal amorphous silica particles (i.e.p. of silica is pH 2) is passed through a column-bed packed with surface-chemically modified nickel slag fibers under natural pH conditions, the colloidal amorphous silica particles are recovered by attachment onto the surface of the surface- modified nickel slag fiber. The recovery of colloidal amorphous silica by attachment is 97-99%, resulting in the production of a relatively clean and silica free output. Aluminum hydroxide, Al(OH)3, was also used to modify the surface –chemical property of the nickel slag fiber. In the same way, it also exhibited a positive response with the collection of colloidal amorphous silica from its bulk liquid, but yielding a lower recovery of 90%. This may be attributed to the lower surface potential and iso-electric point of pH 9.3 for Al(OH)3. The separation process was evaluated and analysed using existing potential energy theories. Figure 1 shows a micrograph of the surface of an unmodified and the Al(OH)3 –modified surface of nickel slag fiber."

Jan 1, 2003

By John A. Herbst

The Mineral Processing Industry needs accurate Production Simulators for the design of future plants and expansions. To achieve this, these simulators should not only provide an accurate portrayal of the dynamics of individual pieces of equipment they should include the impact of discrete stochastic events such as scheduled and unscheduled maintenance so the relationships between availability, equipment sizes, and plant capacity are understood. To provide such a tool accurate dynamic Population Balance Models need to be combined with solid discrete event modeling. The current paper provides a description of how these two disparate modeling techniques were combined and the associated benefits from this combination. Keywords: dynamic plant simulation, population balance models, discrete event models, prefeasibility and feasibility studies, plant design and expansion

Sep 1, 2012

By J. Gong

Fine mineral particles pose two challenging problems in froth flotation, i.e., ineffective recovery of fine hydrophobic particles and mechanical entrainment of fine hydrophilic particles. The first problem has attracted much research effort while the second problem has received much less attention. We have recently proposed a method to deal with mechanical entrainment, i.e., utilizing the flocculating power of polymeric depressants to flocculate fine gangue particles and making the flocs big enough so that the mechanical entrainment of these particles can be reduced or eliminated. In this paper, we report results on the use of polyethylene oxide (PEO) in controlling quartz gangue in the flotation of sulphide ores. PEO was found to flocculate fine quartz and lower its entrainment. It was also found to modify air/water interfacial properties and acted as a frother, which could increase gangue entrainment. Nevertheless, when used at starvation dosages, PEO was found to significantly improve the grades of the floated sulphide concentrates.

Jan 1, 2014

By J. Seo, W. Kim, I. Bae

"Microcrystalline silica impurities such as quartz and opal-CT commonly associated in bentonite should be controlled and removed as far as possible when bentonite is used as biocompatible raw material because they show sufficient evidence of carcinogenicity. Since opal-CT contained in bentonite in trace amounts cannot be well separated by conventional sedimentation method, in this work, the ultrasound-assisted removal of the impurity was attempted. Irradiating ultrasound into bentonite-water suspension promoted the production of fine montmorillonite particles in the suspension and the production markedly increased when montmorillonite was activated by Na2CO3. Subsequent centrifugation of the suspension made it possible to recover pure montmorillonite particles as an overflow product. Only 16.2 mass % of total solids was recovered as an overflow from the non-activated suspension, whereas 63.5 mass % was recovered from the activated suspension at centrifuging speed of 10000 rpm. Increasing sonicating time enhanced the yield of overflow, however, excessive sonication up to 10 min hindered the purification of montmorillonite. It was observed that the peak reflection of (101) plane of opal-CT in overflow increased as sonicating time increased during prolonged sonication. INTRODUCTION Bentonite consisting predominantly of mineral montmorillonite is clay-rich soft rock generated frequently from the alteration of volcanic ash. Depending on the nature of its genesis, bentonite contains a variety of accessory minerals, which may include mainly quartz, feldspar, opal cristobalite/tridymite (opal-CT), calcite, illite and mica. The presence of these accessory minerals can impact the industrial value of the deposit, reducing its commercial value depending on its applications. Therefore, bentonite is often purified by removing these impurity minerals for special applications where specific properties and characteristics are required (Murray, 1999). Among the special applications, bentonite is often used in the cosmetic and pharmaceutical industry as both excipient and active ingredient in the forms of liquid (suspensions, emulsions), semi-solid (creams, ointments) and solid (powder, capsules and tablets). The basic requirements for bentonite to be used as raw material are pure, microbiological and mineralogical inertness. Physical properties such as swelling volume and gel formation are also important. Particularly, microcrystalline silica polymorphs such as quartz, cristobalite and opal-CT should be controlled and removed as far as possible because they show sufficient evidence of carcinogenicity in humans."

Jan 1, 2018

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By N. Pajunen

The basic objectives of current EU waste policy are to prevent waste and promote re-use, recycling and recovery to reduce negative environmental impact (2008/98/EC). In this paper, we focus on drivers and barriers for sustainable development by decreasing amount of waste and increasing material efficiency. Main target is to understand what are the most efficient drivers for environmental friendly decision making for reasonable consumption and use of raw materials. Environmental control instruments usually mean those actions the regulatory authority uses to control and limit environmentally harmful behavior of companies. A major change in the environmental control system took place in the 1980s with the focus moving from specific environmental issues to the environment as a whole. The environmental control system i.e. the legal (administrative), economic and informative instruments focuses on prevention. Before and still, the legislation is one of the main drivers in improving material efficiency. In this paper, we focus on drivers and barriers for effective industrial material use, and mainly on drivers. The objective of this study is to analyze how the drivers are working and are there any possibilities to influence on those. Our aim is also to introduce few examples of the existing supply chains and the drivers for better environmental performance and material efficiency. These examples are also compared with ideal reference scenarios. Our main research question in this article is: ?Are the financial issues the most important driver for environmental friendly strategic decisions?? In addition, retell the story from another perspective: ?The most important barrier for environmental friendly innovations seem to be the investment cost, the high risk involved in committing capital to unproven technology.? Other drivers, like the corporate social responsibility, stakeholder pressure, and general public pressure, will also affect the final decision. This article is based on research projects and literature. Keywords: drivers, decision-making, environmental management, saving primary raw material, material efficiency, sustainable production, critical raw materials

Sep 1, 2012

By Mingfei He, Yude Gao

"The leaching kinetics was studied during leaching of indium-bearing zinc oxide to recover indium. The effects of temperature, sulfuric acidity, particle size, stirring rate on dissolution rate of indium were investigated. Results showed that the leaching process was controlled by chemical reaction at the condition of low sulfuric acid concentration. While the acidity increased to 1.8 mol/L, the leaching process was transformed into an internal diffusion controlling model . The corresponding value of reaction orders under low acidity and high acidity were 1.194, 0.156, respectively. Further calculation results indicated that the leaching reaction activation energy was only 10.97kJ/mol under the condition of high acid. The leaching rate constant was inversely proportional to the square of particle size, while the effect of stirring rate on leaching process was insignificant. The leaching process can be enhanced by increasing the temperature and acid concentration, as well as the decrease of particle size. And a final kinetics eqution was proposed. KEYWORDS Indium, extration, leaching kinetics, zinc oxide INTRODUCTION Indium[1,2] plays an important role in many aspects of living and industrial production owning to its special physical and chemical properties. The reserve of indium is rare on the earth, and most of indium is distributed in some other minerals[3]. Some researchers [4,5] have proposed that indium mainly substitutes for the lattice of other minerals by isomorphous. Therefore, the extraction of indium should take into account of the production technologies of those minerals to comprehensively recover the valuable metals."

Jan 1, 2018

By Paul Gottlieb

This paper reviews the status of automated applied mineralogy today and describes the history and fundamental theoretical and practical bases underpinning the development of automated systems. Details are given of the technical challenges that were faced in creating the new technology and in applying it to a range of applications. In recent years, automated mineralogy has become established as an essential enabling technology for the reliable acquisition of statistically sound comprehensive mineralogical and metallurgical data. This has had a revolutionary effect on the industrial use of such data in the study of geology, mining and mineral processing. Previously, using manual methods, it was not feasible to attempt this work because the large data sets required could not be assembled in a realistic timescale. There was a reliance on individual expert mineralogists and this was not scalable. The speed, reliability, detail and repeatability of the modern automated measurements has now made this type of analysis routine. Automated Applied Mineralogy has come of age! More than 100 systems have been installed around the World. Automated mineralogical analysers such as QEMSCAN® were originally developed as diagnostic metallurgical tools to improve mineral processing plants using samples drawn from plant surveys, bench and pilot-scale tests. They were used mainly for the assessment and auditing of size fractions of mill products, such as concentrates and tails. Subsequently, they began to be used for concentrator design and optimisation where ore characterisation was used to help understand the relationship between the feed ore and its subsequent behaviour in the plant. They are now widely used to measure exploration cores and drill chips from drilling programs to predict eventual metallurgical performance. Ore samples can be classified into metallurgical, as well as geological types, by combining mineralogical features in the ores with metallurgical properties related to grade control, separation, comminution, flotation and leaching behaviour. Three-dimensional block models of ore deposits are now being created based on processing response in addition to geological and mining properties. The development of automated systems began in Australia, the United Kingdom and Canada in the late 1970s and early 1980s. There were many technical challenges. Mathematical theories of randomness, sampling theory, image analysis and stereology were developed to ensure sample representivity so that meaningful information could be obtained. Sample preparation, presentation and measurement methods were developed to ensure that the random sampling was preserved during the measurements. Methods of automatic measurement and mineral identification evolved from the use of electron microscopes, fitted with backscattered electron brightness and energy dispersive X-ray detectors. Operational procedures were required to ensure that these instruments could accommodate a large number of samples and operate unattended for long periods of time. The new technology was progressively applied to a range of commodities and applications and new analysis methods, such as liberation measurement, were needed for metallurgical interpretation of mineralogical data.

Jan 1, 2014

Under the AMIRA P9 project the three-product cyclone-an off-shoot of the conventional hydro-cyclone-that produces three distinct products has been developed. The three-product cyclone shows great promise as a classifier in mineral processing. Industrial and pilot plant trials performed to assess its performance in the classification of the UG2 platinum ore, indicate that the presence of an extra overflow product stream that captures the mid-sized particles, provides improved classification efficiency. To assess the split on component density, samples from the feed and product streams were screened and assays by size for chromite (? = 4.8) and silica (? = 2.65) were obtained. Results from tests performed using this type of hydrocyclone in a number of applications indicates that it can be applied successfully in circuit configurations where the conventional hydrocyc-lone is not suitable. Utilising the three-product cyclone to classify the UG2 platinum ore resulted in an intermediate overflow product stream containing the mid-sized low density silicates and relatively fine high density chromite particles while the finer overflow contained mostly fine silicates and chromite particles. The coarse chromite and silicates reported to the underflow. Due to the increased number of products, the method of using efficiency curves was extended to cater for the increased number of products in the three-product cyclone. Although significant differences in the classification performance of the three-product cyclone were noticed with variations in machine variables a consistent method of assessing the performance was applied. The efficiency curve was adopted and applied and separate efficiency curve properties were obtained for each product stream. The methodology was applied to the component data, and efficiency curve proper-ties for each key component were obtained and compared. This paper discusses the application of the efficiency curve to cyclones producing more than two products and extending the methodology to the different components in the feed.

Jan 1, 2014

By Yimin Zhu

This paper introduces the sixteen mappings and rules of mineral flotation and the subgroup, period etc in periodic table of chemical element to provide mineral flotation workers to refer in theory and practice research. the nine mappings and rules of mineral flotation and the subgroup, period are Saline minerals including the first main groups and collectors of aliphatic acid and aliphatic amines, Minerals including the second main group elements and collector of aliphatic acid, Hydrated ion of the second main group elements and quartz flotation, The floatability of oxidized minerals including the four main group elements, Organic acid including the fifth main group elements and wolframe, tin flotation collectors, The floatability of sulfide minerals including the fifth main group elements, Inorganic compounds including the seventh main group elements and mineral flotation regulator, Oxidized minerals including the forth Subgroup elements and organic flotation agents with phosphorus and arsenic, Oxidized minerals including the fifth subgroup elements and organic floating agents including the fifth main group elements, Minerals including the first subgroup elements and CN-, Sulfide minerals including the second subgroup elements and CN-, The effect of the highest N-valency inorganic acids or salts including p area elements of the third period in mineral flotation, Oxidized minerals including transition elements of the forth period and 3# flocculating agent, The floatability of minerals including elements of the sixth period, Element area of generating compositions and the collecting theory of mineral flotation and so and. Keywords: mineral flotation, periodic table of chemical element, subgroup, period, regulator, coordination chemistry

Sep 1, 2012

By D. Z. Wang

A red copper plate, discovered in the ruins of Dachengshan in Hebei province, was recognized as a forged one rather than a cast one, which means it was probably made from natural copper during the Longshan Culture period (2200~2208 BC) in the Chinese history. The copperware, found in the Niangniang Tai relics in Wuwei city, Gansu province, contains 99.6% copper and 0.4% Sn, Pb, Sb and Ni, which was guessed to be made during the Qijia Culture about 2000~ 1900 BC in the Chinese history in the late Neolithic before Shang dynasty. This shows that Chinese ancestors were able to distinguish, sort and use some native metals and minerals more than 4000 years ago.

Jan 1, 2014

By Erico Tabosa

The turbulence characteristics and measurement techniques for agitated tanks are well established for liquid and liquid-gas systems. However, the literature shows that the overall energy dissipation rate (related to turbulence) is affected not only by air addition, but also by the concentration of solids. Unfortunately, there are no reliable measurement techniques for characterizing turbulence in a three phase (liquid-solids-gas) environmental system, which is the case in a flotation cell. Therefore, the effect of turbulence on flotation kinetics is very much one of conjecture. The aim of this work was to develop a sensor to characterize the degree of velocity fluctuation, which is related to turbulence, in a flotation cell operating with slurry and air. This sensor comprises a piezoelectric film transducer that converts mechanical to electrical energy. Hence, when the sensor deflects backwards and forwards an AC voltage is created. Flotation studies carried out using this sensor in a 3m3 Metso RCS cell processing a copper sulphide ore showed a highly turbulent impeller zone with transition to a significantly less turbulent zone in the upper portion of the cell. The transition region moves as the cell operating variables are changed, for instance the impeller speed, impeller size, air rate and feed solids concentration. Keywords: mechanical flotation cell hydrodynamics, turbulence characterization

Sep 1, 2012