Search Documents

By Y. De Gao, C. Gang Zhong, X. Yang Qiu, Li Wan

The chelating reagents are used as effective collectors in wolframite flotation, and certain metal cations need to be added using chelating collectors so as to activate valuable minerals and obtain good flotation indexes. Different metal cations will result in different reactivity with collectors, in order to select the effective activator in BHA flotation of wolframite, the activation effectiveness of different metal cations on wolframite ((Fe,Mn)WO4) flotation were studied using pure minerals. The results showed that the wolframite activation by Pb2+was the best among the selected cations. The maximum flotation recovery of wolframite was found to be 95.58 % under conditions of 100mg/LBHA and 1×10-4mol/L of Pb2+at pH 9. The dosage of Pb2+needs to be controlled in an optimum range. Also, the activation mechanism of Pb2+ on BHA flotation of wolframite was investigated by measurements of contact angle, zeta potential, adsorption capacity and IR spectroscopy. It was found that Pb2+ could chemically adsorb onto the wolframite surface improving the flotability of wolframite and enhancing the adsorption of BHA on wolframite. When the dosages of BHA and Pb2+ were 100 mg/L and 1×10-4 mol/L, the adsorption quantity of BHA on wolframite sharply increased up to 0.30 mg/L at pH 9 compared with wolframite treated with only BHA.

Jan 1, 2014

By Shobha Kumari

Coal is the prime source of energy in India. It now contributes to about 55% of the total power generation and will continue to have its major share in the energy mix of the country in the foreseeable future. Thermal coals of India, known for their wide variations in nature and categorized as difficult to wash due to their typical mineral matter association with the organic matrix, need suitable beneficiation technique for quality upgrade for improving the overall economics, efficiency and pollution free power generation. A non-coking high-ash coal, collected from Vasundhara open cast mine of the Ib Valley Coalfield, Orissa, has been characterized along with its different fractions obtained in the process of beneficiation for distribution of minerals using FTIR, XRD and ash analysis. The raw coal was fractionated by size as well as by density. It has been observed that ash yields and mineralogical composition (found to be mainly kaolinite and quartz) have no appreciable change in different size fractions, indicating homogeneous distribution of minerals in the coal matrix. However, for the different density fractions the mineral composition and ash yield have significant variations. The quartz content of the beneficiated coal visualized with 34% ash yield, as mandated by the Ministry of Environment and Forest (MOEF) for the use of coal in power plants is reduced to half of that of the raw coal. As quartz is the most abrasive mineral in coal, reduction of its proportion obviously signifies considerable reduction of wear of power plant machinery when beneficiated coal is fed to utility boiler for generation of power. The composition of the major minerals quartz and kaolinite as determined, also favors formation of ash of refractory nature during combustion. Keywords: IB valley coal, beneficiation characteristics,

Sep 1, 2012

By G. C. Li

Gold extraction using iodide leaching from refractory carbonaceous gold ores was studied. Thermodynamic analysis of iodide leaching chemistry had been carried out. Eh-pH diagram of Au-I2-I--H2O leaching system showed that the coordinating active forms from iodides were I3- and I-, while the major coordinate compound formed during iodide leaching was AuI-. For leaching parameters optimization, technological parameters such as I2 concentration, I2 :I- ratio, oxidation assisting agents, liquid/solid ratio, and leaching duration were studied. The leaching results showed that the average Au leaching rate reached 91% and 92% for oxidized ore and roasted primary ore respectively. Leaching process proceeded in weekly acidic or neutral slurry at ambient temperature; the leaching duration was 4 hours. After that gold was extracted from the pregnant liquor by activated carbon adsorption ? desorption ? electrowinning process. Gold recovery was over 93% in the adsorption process, while the gold recovery in electrowinning process was about 95%, provided that the initial gold concentration is 40mg/L or larger. For iodine regeneration it is enough to add hydrogen peroxide in excess into the filtrate after gold electrowinning, all the iodides existing in the solution in any forms would be precipitated in the form of elemental iodine.

Jan 1, 2014

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By M. L. Cao

In this study, a montmorillonite organo-intercalation compound (MOIC) was synthesized by using a Na-modified bentonite (NaB) as a matrix and hexadecyltrimethylammonium (HDTMA) bromide as an intercalating reagent under microwave irradiation. The synthesized products were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), organic carbon content measurement, and adsorption density determination. The results show that, at 10% suspension concentration and 10 minutes irradiation in a 130-W microwave oven, the basal spacing d(001) of the synthesized MOIC increases to 2.209 nm from the original 1.218 nm of NaB. The MOIC has much higher adsorptive densities to nitrobenzene and aniline from aqueous solution than the NaB. The adsorption isotherm of nitrobenzene on the MOIC is linear, and the adsorption is mainly the result of nitrobenzene?s preferred partition in MOIC over aqueous solution due to MOIC?s hydrophobicity. The adsorption isotherm of aniline on MOIC follows the Freundlich equation and the increased adsorption is not only the result of aniline?s preferred partition in MOIC over aqueous solution but also that of the MOIC?s surface adsorptions.

Jan 1, 2014

By Antony Amberg, Gonzalo Saldías, Romke Kuyvenhoven, Catherine Souza, Heriban Soto, Francisco Soto

"Vizcachitas is an advanced stage copper–molybdenum porphyry deposit, fully owned by Los Andes Copper and located in Central Chile. The property contains an indicated resource of 1,038 million tonnes grading 0.37% Cu and 0.012% Mo, and an inferred resource of 318 million tonnes grading 0.345% Cu and 0.013% Mo (Coffey & Alquimia, 2014). The deposit occurs in the same geological belt as several other giant copper-molybdenum porphyry deposits including Río Blanco-Los Bronces, Los Pelambres-Pachon and El Teniente. In 2018, the original Preliminary Economic Assessment (PEA) study from 2014 was updated; this paper presents the geometallurgical testwork that was performed to support that update. The testwork focused on the metallurgical characterization of 40 DDH samples and the development of a more profound orebody knowledge by relating geological features with metallurgical performance. The scope of work included complete chemical and mineralogical QemSCAN characterization; SAG, ball mill and abrasion testing; complete rougher and cleaner kinetics including locked-cycle-test; environmental ABA and settling tests on rougher tailings. The results show that the ore can be classified as medium-hard, with a hardness that is slightly below the average for large Cu/Mo deposits in the region. A good correlation was found between lithology and breakage characteristics, implying that the specific energy consumption (kWh/t) is well correlated to rock type. The results of the flotation tests were very encouraging and did not show significant variability. An overall Cu recovery of 91% can be expected for the flotation circuit. The use of a relatively coarse primary grind size gave good final recovery and grade for both Cu and Mo, and deserves further attention in future work, as this impacts positively both energy consumption and water recovery.INTRODUCTION Los Andes Copper Ltd. is a Canadian exploration and development company focused on the acquisition, exploration and development of advanced stage copper deposits in Latin America. The company owns 100% of the Vizcachitas project in Chile, the largest copper deposit in the Americas not controlled by the majors. Vizcachitas is a copper-molybdenum porphyry deposit, located 120 km north of Santiago, in an area of very good infrastructure."

Jan 1, 2018

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By A. I. A. Salama

In this paper, the problem of sedimentation and consolidation of poly-disperse suspensions is considered. The solid particles are assumed to be of different densities. If the sediment solids stresses are dropped out of the system equations and using the Richardson and Zaki hindered settling model, it has been found that in the limit, i.e., as time approaches infinity, the fluid is completely displaced to the top of the sediment zone. Furthermore, the species segregate completely with the heavier and coarser particles at the bottom of the sediment and the lighter and finer particles at the top of the sediment. Practical observations do not support these behaviors and physical-ly such behaviors do not exist; consequently, results of this kind in the literature are unrealistic. Here, a mathematical structure of the poly-disperse sedimentation and consolidation problem has been proposed. In this case the compaction zone species solids stresses are introduced in the momentum balance equations of the system. The species solid stresses in the sediment are constrained so that the system equations are consistent, i.e., sedimentation and consolidation of two or more identical species should behave as a mono-disperse system. Such a condition has not been recognized and imposed in some of the studies in the literature, which has led to unreliable results. Two practical forms of species stresses that satisfy the system consistency condition are here proposed. It should be noted that the study of sedimentation and consolidation of poly-disperse suspensions could result in more realistic suspension interfaces compared to mono-disperse suspensions, and could lead to more reliable engineering designs of tailings ponds. Predictions of sedimentation and consolidation in models of poly-disperse suspensions are demonstrated using published data.

Jan 1, 2014

By P. Prusti

An air dense medium fluidised bed separator (ADMFBS) is the efficient process for dry beneficiation of coal. Magnetite powder is used as medium to make required pseudo-fluid density in the fluidised bed. The dynamics behavior of coal particle with reference to its position changes from ideal solution to pseudo-fluid condition in different bed densities depending on its shape, size and density. In this study, three set of projected areas of coal particles were taken. Each set contains four different shapes i.e., cubical, rectangular prism, spherical and triangular prism with different density starting from 1.3 to 1.8 gm/cc. It is observed that coal particles having density less than the bed density, floats in different positions in the dense medium fluidised bed. Higher projected area particles float in deeper height in comparison with smaller projected area. The difference in position of coal particles in the bed increases (nearly 1 to 4 cm) as the coal density approaches towards bed density irrespective of the different shapes. Different shapes of coal particles behave in different ways based on the operating parameters like bed density, coal density and projected area of coal particle. Empirical model equations are proposed to predict the position of coal particle of each shape in the air dense medium fluidised bed system. Keywords: ADMFBS, particle dynamics, projected area, shape

Sep 1, 2012

By S. M. Viduka

This paper presents a numerical investigation of solid separation in jigging device, which is a gravity separation method widely used in ore processing. Separation is recognized as being heavily dependent on fluid motion in the jig. This study explores the effects of the inlet time dependent velocity profile on jigging performance. Modelling of the liquid-solid system is performed through a combination of computational fluid dynamics (CFD) to simulate liquid flow and discrete element method (DEM) to resolve particle motion. The initial packing conditions consist of a binary-density particle system of 1130 particles each 1 cm in diameter. A variety of jigging profiles are implemented in jigging. The saw tooth pulsation profile is selected with three variations in both amplitude and frequency. The performance of each profile variant is compared in terms of solid flow patterns, separation kinetics, energy, and mean particle position. These quantitative comparisons demonstrate significant differences in the segregation rate, energy, and solid phenomena, helping find an alternative optimum operating setting for the system.

Sep 1, 2012

Considerable attention has been, and is being, given to the physics of water-films associated with bubble interactions at surfaces. In contrast, little information on the chemistry of such films has been reported. This communication reports a method using sum frequency vibrational spectroscopy (SFVS) to describe hydrogen bonding of interfacial water molecules in water films created with bubbles at hydrophilic and hydrophobic surfaces. The SFVS spectra of water films at hydrophilic silica surfaces differ significantly from the spectra of water at a hydrophobic silica surface. The SFVS spectra indicate that a very ordered water structure exists in water films at the hydrophilic silica surface during contact with a bubble and that the extent of hydrogen bonding increases with an increase in contact pressure. Such structural considerations as well as repulsive electrostatic and Van der Waals forces account for film stability for a bubble at the hydrophilic silica surface. In contrast, the SFVS spectra of water at a hydrophobic silica surface show a lack of hydrogen bonding and are characterized by a distinct absorption at about 3700 cm-1 similar to the spectrum of the air/water interface. These results suggest the presence of a water void, or water exclusion zone, at the hydrophobic surface, as supported by X-ray reflectivity measurements reported in the literature, by atomic force microscopy, and by the results from molecular dynamics simulations. Of course the water film at the hydrophobic surface is unstable with film thinning and rupture upon bubble contact. Under these circumstances it is shown that an attractive Van der Waals force between the bubble and the hydrophobic surface can be expected when the water exclusion zone is taken into consideration. As the thickness of the water exclusion zone increases to a thickness corresponding to the size of nano bubbles, the calculated attractive Van der Waals force increases. This analysis may help to explain the so-called ?short range? and ?long range? hydrophobic forces. Keywords: SFVS spectra, hydrophilic silica surface, hydrophobic silica surface

Sep 1, 2012

By H. Allenius

Today, most requests for quotations force all bidders to follow the bid document to the letter. The choice is then made based on price since it is the only difference in technically identical offers. However, clients allow and even encourage suppliers to come up with alternatives. Overall economy again, is much more than low investment costs. Operation costs may affect the economy of a project far more than a million saved in investment. There is almost always the choice: Should we go for the cheapest solution or should we go for the most economical solution? We strongly recommend the study of the long-term effects on investments as they often surpass any apparent savings in capital expenditure. With high operating costs, time is never on our side. Almost all relevant inputs and outputs in a concentrator have a value that can be expressed in a suitable currency. Unit prices may differ substantially from one operation to the other, but everything has a price tag and globalization has made it possible to move both goods and services to almost any place in the world. Even a rather simple exercise can give a good indication on which process improvements are worth pursuing when investing in new systems or equipment. The ones that do not qualify, as money earners, will naturally appear as clearly. No ?rocket science? is required, just process knowledge, practical experience, an open mind and some common sense and the reward may be the difference of having a good or an excellent project. The model we have developed can be made as detailed as required, but we do not recommend too much detail, as it sometimes tends to distract work and obscure the important issues. Two different process solutions compared in a simplified example illustrate the importance of evaluating a project based on its long-term effects rather than focusing on the investment costs only.

Jan 1, 2014

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By M. Bergerman

Sossego was the first Vale SAG mill operation to process copper-gold ore. It is located in Para state, south east of Amazon region in Brazil. The comminution circuit was designed to treat 41 000 metric tons per day comprising primary crushing, one 11.6 m SAG mill operating in closed configuration with cone crushers, followed by two 6.7 ball mills. In the first three years of continuous operation Vale investigated alternatives for obtained improved performance of the circuit by investigating operating conditions, mainly focusing on SAG mill. A number of actions were then implemented, which resulted in significant increase in overall production. Vale then decided to further assess the performance of the comminution circuit as a function of ore characteristics. A comprehensive ore characterization program was then conducted, together with the calibration of mathematical models on the basis of surveys carried out at the industrial circuit. The simulator was then used to predict the production level associated to each ore type, as well as to establish the optimized circuit configuration and tailored operating conditions. The ongoing validation program is planned to consolidate the selected strategy, as well as showing the benefits in adopting such indices in mine planning, as opposed to rather simplistic approaches. This paper describes in detail the main aspects of optimizing the industrial circuit performance, as well as the successful method for predicting the production as a function of ore characteristics.

Jan 1, 2014

A processing scheme is presented to use one single chemical that has multiple functions to re-duce the use of chemicals and achieve more efficient mineral flotation and solids dewatering. Sti mulisensitive polymers which display hydrophilic/hydrophobic transitions in response to changes in temperature or pH have been found to be useful as such multiple function reagents. They can cause the mineral particles to be either hydrophilic or hydrophobic at one stimuli condition and the opposite at the reverse stimuli condition. Therefore, both particle surface wettability and inter-particle interaction forces are reversibly controllable. When the surface is hydrophilic, particle dispersion is achieved by repulsive inter-particle forces whereas when the surface is hydrophobic, particle aggregation is induced by inter-particle hydrophobic attractive forces. In addition, the hydrophobic surface condition allows for the attachment of particles to bubbles. Flotation and solid settling tests have been conducted with a silica suspension treated with the temperature-sensitive polymer poly (N-isopropyl acrylamide) (PNIPAM). The results indicated that PNIPAM can be used to induce a transition between hydrophilic and hydrophobic surface character at temperature lower or higher than its critical solution temperature (CST around 32oC). Thus, both effective silica dispersion or hydrophobic aggregation and flotation without adding any additional collector have been demonstrated. In tailings treatment, rapid silica settling was obtained with hydrophobic aggregation at temperature above the CST and further sediment consolidation (and water release) occurred at temperature below the CST. Contact angle measurements confirmed the hydrophilic/hydrophobic transition induced by PNIPAM.

Jan 1, 2014

By H. R. Manouchehri

Large variations in flotation characteristics of minerals have been observed in winter and summer in plant practices as a result of changes in pulp temperature. Variations in temperature may affect the quality for pulp and related process water through changes in dissociation of different chemical species within the pulp, as well as changing in gas and metal hydroxide solubility, reagent adsorption and its stability on mineral surfaces, water/pulp viscosity, etc. All of these affect the flotation characteristics of specific mineral to some degree or another. It has been observed in Cu-Pb-Zn and/or Pb-Zn sulfides flotation that sphalerite (ZnS) flotation is strongly affected by changes in pulp temperature. Plant practices have shown that at the both low, e.g., T <10-12°C, and high, e.g., T > 60°C, the recovery for copper activated sphalerite is dramatically dropped. Within this paper the effect of pulp temperature on flotation characteristics of sphalerite is brought into considerations and laboratory flotation tests were conducted in conjunction with surface and solution chemistry analysis to understand the effect of temperature on sphalerite recovery. The effect of temperature seems to be complex since the temperature affects both the physical (hydrodynamics) and chemical phenomena in the flotation cell. In fact all sub-processes in flotation, i.e., collision, attachment and detachment, are affected by changing in temperature. Experimental results indicating that at alkaline pH values, e.g., 8.5 to 10.5, the recovery for copper-activated sphalerite is dramatically reduced when temperature is below 10-12°C, which is in agreement with plant practice at Boliden?s Garpenberg plant in Sweden. However, results from other studies indicated that the zinc recovery is also considerably decreased at high pulp temperatures, i.e., 62°C and above.

Sep 1, 2012

By T. Mütze

The progress in comminution is often described by the specific surface area and the energy utilization or the brakeage ratio and breakage function. The principal mechanisms of size reduction are therefore, well known. All four parameters share a common disadvantage: They are limited in describing the behavior of a feed material with fine particles and a wide particle size distribution. An alternative is to describe the progress in comminution with ? The particle size distributions Q(x) before and after the stress or ? The particle concentration ratio pcr(x), which combines these two states. In the case of a self-similar fracture behavior, (in short: self-similarity) the progress in comminution can be simplistically described by the relationship between a reference particle size and the stress intensity. Self-similarity means self-similar breakage functions of geometrically similar particles of the same strength, a certain stress situation and stresses up to the breakage point. Self-similar breakage functions show the same curve at different stress intensities when the fragment size x is normalized with a reference particle size xNorm. This behavior was demonstrated for single particle comminution repeatedly and unequivocally. In the field of particle bed comminution, these results differ in literature. Therefore, the self-similarity in particle bed comminution was systematically investigated at the Institute of Mechanical Process Engineering and Mineral Processing of the TU Bergakademie Freiberg as part of a research project. Limestone, quartz, silicon carbide and glass beads, were examined with a hydraulic press. The particle sizes covered monodisperse fractions in the range of 1-1000 µm, bimodal mixtures of these fractions and polydisperse fractions. The results obviously show that there is no self-similar fracture behavior in the case of glass beads, quartz and silicon carbide. Statements on the self-similarity of limestone are much more difficult: Only some of the investigated limestone fractions show a similar clear, non-self-similar behavior. Self-similar curves appear particularly for fine monodisperse fractions as well as bimodal mixtures, which stressed with pressures above 200 MPa. Considering the measurement accuracy of particle size analysis the coincidence of the curves can be explained by the fact that progress in comminution almost ends above 200 MPa. At this point, a hydrostatic stress state is reached in the particle bed which is known from the literature. This stress state inhibits further fractures. Overall, it has been verified for the investigated materials that there?s no self-similar fracture behavior in particle bed comminution. One reason for the diverse opinions in literature is that there are three types of particles after the comminution in the particle bed: ? Particles which are stressed below their breaking point, ? Particles which are stressed right up to the break point, and ? Particles which are stressed beyond their breaking point.

Sep 1, 2012

By Shobhana Dey

A low volatile medium coking coal from Jharia coal field, India was used for this investigation. The proximate analysis of the sample shows that it contains about 25% ash, 21.4% volatile matter and 52.4% fixed carbon. The sizewise ash analysis of -0.5 mm coal indicates that -0.5+0.15 mm fraction contains lower ash (21.9%) than -0.15 mm fraction (29.7%). The flotation characteristics of the -0.5 mm coal were determined by release analysis. The study reveals that recovery of combustible at 15% ash is about 27% and 43% at 17% ash level. The low recovery is due to the presence of high ash in finer fraction. In order to improve the recovery, the -0.5 mm feed was classified into -0.5+0.15 mm and -0.15 mm fractions, and subjected to flotation separately. The recoverable combustible obtained from the release analysis of -0.5+0.15 mm at 15% ash level is 46%. The effect of collector dosage, frother dosage and aeration rate on flotation was studied. The responses of these variables in collectorless flotation of the -0.5+0.15 mm fraction containing low ash were also studied. A lower aeration and frother dosage favored the generation of clean coal with low ash. The ash content in the tailing stream from -0.5+0.15 mm flotation circuit is close to that of the original -0.15 mm fraction. The former is ground to -0.15 mm and the two fractions are processed together. As -0.15 mm fraction contains relatively higher ash, collector aided flotation using sodium silicate was performed to recover the clean coal with 17% ash. The products of the overall flotation circuit having different ash levels were recommended for use in different applications. The reject from -0.15 mm flotation circuit contained 56.4% ash which can be used for fluidized bed combustion (FBC). This eventually leads to complete utilization of coal.

Sep 1, 2012

By P. Pourghahramani

Several structural characteristics change during intensive milling such as chemical composition, phase transformation, crystallite size, lattice strain, lattice parameter (s) and solid reactivity etc. The creation of defects enhances the stored energy (enthalpy) in the solids and consequently causes a decrease of activation barrier for the process and/or subsequent processes. In this paper, the effects of milling on the structural changes of hematite have been investigated using dry millings. The structural changes have been characterized using a combination analysis of BET surface area measurements and X-ray diffraction (XRD) analysis. Besides, the hydrogen reduction behaviors and kinetics of mechanically activated samples and initial sample were studied using simultaneous thermal analysis (STA). The methods of Williamson-Hall and Warren-Averbach were used for analyzing of XRD patterns to resolve and extract the microstructural characteristics of hematite phases. It was concluded that the breakage and aggregation of particles take place mainly in the starting and prolonged stages of dry grinding, respectively. The BET surface area enlarged steadily over the grinding processes whatever milling methods were utilized. The characterization of structural changes revealed that the hematite milled under various conditions did not undergo any significant reaction or phase transformation during milling processes. In addition, X-ray amorphous phase con-tent increased gradually with extending the grinding intensity. The maximum X-ray amorphous phase exceeds about 81% after 9 hours of milling in both tumbling mill and vibratory mill. The Williamson-Hall plots revealed the anisotropic character of line broadening for deformed hematite and changes in the trend of microstructural characteristics as a function of milling time. It was found that the surface weighted crystallite size decreases and lattice strain increases over the grinding periods. The minimum surface weighted crystallites were calculated about 17.3 nm, 12.2 nm for the products of tumbling and vibratory mills respectively. The maximum lattice strain,, in the grinding with tumbling and vibratory mills was calculated about 4.44×10-3 and 3.95×10-3respectively. 21/210nmLe=<> The non-isothermal kinetic analysis of the products revealed that Fe 2O3 reduced to Fe in a two-step process via Fe3O4. Intensive grinding resulted in improved resolution of overlapping reduction events. It was also established that the mechanical activation had a positive effect on the first step of reduction. The prereduction step in the activated samples initiated and completed at lower temperatures than that in non-activated samples. The activation energy of reduction decreased at the first step of reaction with increasing the grinding intensity. Intensive milling increased slightly the average activation energy of the second step of reduction due to the present of finely agglomerated particles and intensive sintering of the particles in higher temperature ranges.

Jan 1, 2014