Search Documents

By Eric Brandner

Expansive soil formations can be found throughout the United States. When subjected to wetting, many of these formations have the potential to swell and exert large uplift forces which can significantly damage lightly-loaded structures. Designing an economical foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material, or drilled shafts, can be costly and problematic. Piles made from recycled polymer materials may provide a solution. Due to a lower coefficient of friction along the interface than piles made from traditional materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure which minimizes the risk of significant structural damage. This paper presents the preliminary results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six 13 in. (330 mm) diameter recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. The piles varied in length from 15 ft. to 25 ft. (4.6m to 7.6 m). Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity, while the additional four piles are being subjected to long-term monitoring of uplift movement. A cast-in-place concrete pile, with a diameter of 6 in. (152 mm) and length of 15 ft. (4.6 m), was also installed at the test site for monitoring. The preliminary results indicate that the use of solid recycled plastic piles is a viable alternative for support of lightly-loaded structures in expansive soil environments.

Jan 1, 2009

By Ambarish Ghosh, Subhaprasad Chakraborty

"Construction of basement floors has become necessary to meet the requirement of parking in office and residential complexes and in hospitals for radiotherapy treatment. Important projects coming up in Kolkata are mostly in closer proximity of residential buildings, office buildings and historical monuments. Sheet piling is mostly used as temporary shoring system during construction. Deep excavation in urban environment creates great problem related to construction induced vibration due to driving of sheet piles for basement, pile driving etc. which raises the chances of damage of adjacent buildings and nearby structures. Vibratory sheet-pile driving is the most common method of sheet pile installation. The knowledge of induced vibration due to this phenomenon is still very deficient. This paper presents the analysis of measured vibration data collected from different sites of Kolkata with varying soil profile. Typical two case studies of sheet pile and pile driving has been presented and the vibration values are analysed. The responses of the vibration are reported in terms of peak particle velocities (PPV). To evaluate the effects of vibration due to pile driving two aspects have been considered: the effect of the energy entering the ground from the pile and the effect of the soil condition.INTRODUCTIONIn urban areas infrastructure development projects are mainly located adjacent to existing structures like residential buildings, offices and historical structures. The construction work of such project influences the surrounding environment as well as human perception (Wiss 1981). During the construction of basement for residential complexes and hospitals sheet piling is mostly used as temporary shoring system or as to support the earth mass. The vibration induced due to driving of piles and sheet piles have been presented herein. Deep excavation projects close to existing structures increase the concern of environmental impact. For this reason the vibration assessment and prediction has become a subject of great interest. It is important to develop a site specific model for predicting the ground vibration resulting from pile and sheet pile driving at the construction sites. The developed model gives the efficacy to guide the engineer to select the construction methodology ensuring the safety of the surrounding structure. The model developed here is site specific and the parameters that has been used are dependent on the soil condition and the energy source."

Jan 1, 2015

By Paul Suver

The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.

By David Coleman

This paper presents a case history involving the installation of drilled in piles with rock sockets for the Bicycle and Pedestrian Path project located west of the Henry Hudson Parkway within the Riverside Park between 83rd Street and 91st Street at the Hudson River in New York, NY. The paper specifically addresses access and construction procedures for a marine installation when working in an urban and environmentally sensitive setting.

By Paul Suver

"The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.CLSCW Description:Closed end steel pipe of varying outer diameter (O.D.) is installed by various technologies at varying depths depending on subsurface geology. The wells are arranged as stand alone wells or in groups joined in parallel or in series or in a combination of both. These pipes may also serve a dual function as foundation supports, deep foundation pile, anchors or earth retention components. These wells are then internally coated to minimize corrosion. The wells are then plumbed and capped to create a vessel equipped with a supply and return water line.The stand alone well or group of wells is then used as a ground heat exchanger for a ground source heat pumps located in or around the building.The ground source heat pumps provide heating and cooling to the building either with a traditional ducted distribution system or with radiant heating and cooling. These systems can reach efficiencies three times greater than traditional gas fired heat sources and five times greater than traditional air conditioning sources."

Jan 1, 2017

By Terrence R. Udland, Russell D. Call

"Honored with a DFI 2006 Special Recognition Award, the Four Bears Bridge was constructed across Lake Sakakawea and opened to traffi c in September 2005. The very large lake size and severe winter conditions required an effi cient foundation design capable of resisting extreme ice loading and able to be effi ciently constructed in waters up to 90' deep (27.4m).DESIGNING FOR EFFICIENCYLocated in a remote area of North Dakota, the Four Bears Bridge replacement was a major undertaking for the North Dakota Department of Transportation, with dual goals of providing a new structure that would endure a severe environment, while enhancing the natural beauty of the area. Competing bids would achieve the best price for the owner, challenging the design team to creatively solve the engineering challenges unique to the site. Foundations for North Dakota’s new Four Bears Bridge had to accommodate water level fl uctuations of up to 40 feet (12m), along with extreme ice loading and be effi cient in order to be the low cost solution at the time of bidding. All three major criteria were achieved through the use of an effi cient ‘fl oating’ lost precast concrete cofferdam founded on steel pipe piles, which allowed the contractor to achieve the project schedule. The result is an award-winning bridge that is contextually sensitive to the environment. The bridge aesthetics pay tribute to the Three Affi liated Tribes, the Mandan, Arikara and Hidatsa, who reside on the Fort Berthold Indian Reservation, adjacent to the bridge site.The original Four Bears Bridge was located over the Missouri River near Elbowoods, the native grounds of the Three Affi liated Tribes. Construction of the Garrison Dam in the early 1950’s created Lake Sakakawea, a fl ood control project on the Missouri River, and resulted in the area being fl ooded. The bridge, along with many tribal members, was relocated to a site near New Town. The bridge provides the primary crossing of Lake Sakakawea and is a critically important transportation element for the residents of the Fort Berthold Indian Reservation. The relocated bridge had become functionally obsolete and not replacing it would require a detour of 170 miles (274km). The North Dakota Department of Transportation determined that it should be replaced. In order to achieve the most effective solution, the North Dakota Department of Transportation selected a design team responsible for the creation of competing steel and concrete designs that were competitively bid. The design team was led by Kadrmas Lee & Jackson, with FIGG responsible for the concrete bridge design, while Lichtenstein Consulting and Kadrmas Lee & Jackson completed the alternate steel bridge design."

Jan 1, 2007

By Matthew C. Janes, Mark C. Spence

"A former coal gasification site next to Rock Bay in Victoria, BC, Canada required a barrier to permit dewatering and excavation of the bay and surrounding property. The adjacent property owners had stringent requirements at the boundaries of their properties. Isherwood Geostructural Engineers designed a temporary steel sheet pile (SSP) water retention structure and excavation shoring system along the perimeter of the site. The project involved challenging geotechnical conditions in soft clay soils and a multi-faceted construction staging plan involving the diversion of two large storm water outfalls that drained into the bay. Despite a well-conceived design and construction plan, unexpected site conditions and delays led to significant changes in design and construction approach. Employment of the Observational Method and on-the-fly geotechnical investigation were instrumental in maintaining project momentum and schedule. The paper presents the geotechnical and geostructural design details and construction events as they transpired, highlighting the key issues, discussions and lessons learned.INTRODUCTIONFor over 100 years, the Rock Bay Site, in Victoria, British Columbia, Canada, had a legacy of contamination left behind from previous industrial activities. The site was the former location of a coal gasification plant that was in operation from 1862 to 1952. The site was also an infilling location for a nearby tannery and sawmill. The remediation of the Rock Bay Site involved the excavation and replacement of approximately 300,000 tonnes of contaminated soils on Transport Canada’s property. The project commenced in 2004 and has occurred over several phases on multiple properties. In the third and final phase of the project, a temporary steel sheet pile (SSP) excavation shoring system and ocean barrier wall – required to seal off the bay – was employed to enable disposal and replacement of approximately 90,000 tonnes of contaminated soils from the shoreline and base of the bay."

Jan 1, 2016

By Dale Berner, Michael O’Sullivan

"This article focuses on lessons learned from innovative designs including in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers (USACE) megaprojects. Olmsted Dam FoundationThe over $2 billion Olmsted Dam on the Ohio River is currently under construction 16 mi (29.6 km) upstream from the confluence with the Mississippi River. The project is under the jurisdiction of the Louisville District of the USACE. It will consist of an 800 ft (244 m) long tainter gate section, a 1,400 ft (427 m) navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two 1,200 ft (366 m) locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons. A significant consideration was its proximity to the New Madrid Fault, which could impose an 8.4 Richter scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by the designer included a response spectra analyses, lateral pushover analyses of pile foundations, hydrodynamic added masses, pile group effects, and the development of kinematic motions as a result of the soil-pilestructure interaction."

Jan 1, 2016

By Steve Davidow, Nick Salisbury

"The Sunrise Powerlink project received numerous industry awards for excellence. The DFI C. William Bermingham Innovation Award recognized the innovative use of prefabricated steel micropile caps to increase safety, accelerate project schedule and minimize the project carbon footprint. DFI’s Outstanding Project Award (OPA) and World Cup of Micropiles Challenge Award honored the project as a whole and its positive outcome and industry example. Sunrise Powerlink involved construction of San Diego Gas and Electric’s (SDG&E’s) new 117 mile (188 km) 500/230 kilovolt transmission line from Imperial County to San Diego County, Calif. The alignment traversed a wide variety of geotechnical conditions, including desert, mountain and marine environments, and many of the 421 lattice tower structures used to carry the transmission lines were located in remote, rugged or environmentally-sensitive terrain.Micropiles were introduced as a solution to foundation construction in these challenging areas, which ultimately involved the design and application of Crux Subsurface Inc.’s patented steel micropile cap at 234 tower locations. This was the inaugural application of the technology, and a significant component to ensuring a successful project outcome. Foundation ChallengesThe alignment crossed a number of protected environments, including National Forest land, critical habitat for bald eagles and Peninsular big horn sheep, and numerous private properties. As a result of the remote, rugged terrain, it was initially determined that 75 lattice tower locations would not permit road construction access and would require helicopter-only construction techniques. A strict in-service date combined with long permitting lead times eventually increased this number to 234 sites. Preconstruction access constraints prohibited site-specific geotechnical sampling, so initial foundation designs were completed using only available seismic geophysical surveying and preliminary mapping data. The combination of these challenges required a foundation alternative that could accommodate variable subsurface conditions, required a minimal environmental footprint for installation, and featured lightweight materials and equipment that could be transported by helicopter."

Jan 1, 2014

By Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"Over the last 10 years, the Minnesota Department of Transportation (Mn/DOT) has had a very active program of replacing many major bridges, large structures spanning the Mississippi River. The deep foundations for these new structures include both drilled shafts and large diameter open-ended driven steel pipe piles. Most of these projects included load tests, both axial and lateral.The geology of this area of Minnesota includes some interesting foundation challenges, including highly organic and compressible very soft silts and clays to very dense sand and gravel overlying sedimentary bedrock. In some cases scour requires embedment into rock, and the bedrock formations may range from very soft sandstone to very hard dolostone. Artesian groundwater conditions can sometimes complicate drilled shaft construction, but the rock is otherwise very favorable for drilled shafts. Experience with the open-ended driven steel pipe piles (typically 42 and 48 in, 1.07 and 1.2 m diameter) suggest that these piles most often penetrate even dense granular materials to achieve bearing on rock. Experiences with drilled shafts socketed into the soft sandstones demonstrate that these rocks provide very favorable conditions for drilled shafts, so long as suitable construction practices are followed. Here we present several recent case histories regarding the foundation design and construction of major bridge projects in the vicinity of Minneapolis, Minn., including the Wakota Bridge, the I-35W replacement, the Lafayette Bridge, the Hastings Bridge and the St. Croix Bridge. Some lessons learned from construction and load testing of both types of foundations are described along with implications for design in similar soil and rock conditions."

Jan 1, 2013

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The new San Francisco 49ers Levi’s Stadium is part of the next generation of sporting facilities. Constructed in Santa Clara, Calif., the new structure has 68,500 open-air bowl seats and includes a 7- story tower housing more than 150 suites. The overall project includes the stadium structure, elevated open pedestrian walkways, commercial community space, three new pedestrian bridges and improvements to the adjacent light rail station. Sustainable design for the project includes a green roof, photovoltaic panel and a ground source geothermal system. Stadium-wide next-generation Wi-Fi capability is another feature. The design-build project team included HNTB (project architect), Magnusson Klemencic Associates (MKA, structural designer) and a joint venture of Turner Construction and Devcon Construction (TDJV, general contractor).During preconstruction, the 49ers’ original design team and the design-build team formed later worked together to facilitate communication and provide continuity. This helped to meet the project’s aggressive schedule. Working directly for the 49ers, with the design-build team, Treadwell & Rollo (T&R) served as the geotechnical engineer of record for the project from preliminary to final design and through construction. Although not contracted directly to TDJV, the stadium ownership encouraged direct interaction between T&R and TDJV and improved responsiveness to geotechnical issues during design and construction.Subsurface ConditionsThe new stadium lies within the Santa Clara Valley, a deep alluviumfilled basin resulting from historic movement on the active and potentially active strike-slip and thrust faults that bind the valley. The valley is filled with Holocene age (approximately 11,000 years old to present) alluvium, consisting of levee and basin deposits, with bedrock more than 750 ft (229 m) beneath existing ground surface. The stadium site is between two of the highly-active faults in California, the Hayward Fault 6.8 mi (11 km) northeast, and the San Andreas Fault about 11.8 mi (19 km) southwest."

Jan 1, 2014

By David R. Shields, Michael T. Bracher

"The $330 million (U.S.) Dana-Farber Cancer Institute’s Yawkey Center for Cancer Care (Yawkey Center) sits in the heart of Boston’s Longwood Medical Area. The Yawkey Center is a cutting-edge cancer care facility that houses Dana-Farber’s adult clinical care and clinical research programs. Standing 14 stories above grade, it includes 7 stories of underground parking extending 75 ft (23 m) below ground. The structure is on a 198 by 186 ft (60 by 57 m) site sandwiched between Dana-Farber’s 13-story Richard A. and Susan F. Smith Research Laboratories Building, the Medical Area Total Energy Plant (MATEP), Jimmy Fund Way, and Brookline Avenue, a busy four lane artery through the heart of the Longwood Medical Area. Together with Simon Design Engineering, the project structural engineer, GEI Consultants designed an innovative foundation and excavation support system to isolate the building from ground vibrations generated by the adjacent MATEP power plant. In effect, the Yawkey Center is a 21-story free-standing structure that starts 7 stories below grade.The MATEP facility provides power for 9 million sq ft (840,000 sq m) of occupied space in the medical area. There are six 32-cylinder diesel engine generators in the facility that produce low-frequency ground vibrations in the 10 Hz range, similar to the natural frequency of typical building elements. The resonant response of the Yawkey Center building structure to these ground vibrations would affect the performance of sensitive medical research equipment and cause an unacceptable environment for clinical care.The soil profile at the site consists of stiff clay, fine sand, glacial till, and bedrock consisting of hard metamorphosed conglomerate. In-situ measurements of ground vibrations performed in boreholes showed that there was little attenuation of the vibrations with depth in the soil layers overlying the bedrock, but the vibration amplitude in the bedrock was markedly lower than in the overlying soil. Based on this data, an innovative foundation system was designed to support the building on bedrock located up to 110 ft (34 m) below ground surface, while isolating it from the surrounding soil. This was done by physically separating the below-grade parking garage floors from the perimeter foundation walls to create a free-standing structure supported on the bedrock"

Jan 1, 2012

By Madhira R. Madhav

In an alluvial deposit consisting of layers of sandy silt with clay and kankar nodules, driven cast in situ piles are provided. The piles end on a stiff bearing stratum To verify the available design capacities, compression, pull-out and lateral load tests are conducted in situ. The elastic continuum approach is used to estimate the equivalent modulus of deformation of the deposit. A comparison is made of the values from the three types of tests.

Jan 1, 1996

By D. A. Ponniah

The installation of a pile is considered analogous to the expansion of a cylindrical cavity of a diameter equal to that of the pile. Using Vesic's theory of the expansion of cavities the effect of soil properties on pile installation loads, radial pore and total pressures are evaluated. The theoretical results are compared with load and pressure measurements made in field trials in a stiff clayey glacial till in the U.K.

Jan 1, 1987

By H. R. Shen

Cushion materials are one of the most important links in an efficient piling system. In the past, little has been done in China on this problem, so engineers are still used to those traditional woods, papers and coir ropes. In this paper, the SOA of piling cushions, their testing method and parameters used in wave equation analysis for piling are briefly reviewed. The static and dynamic mechanical characteristics of 3 types of cushion material have been determined in laboratory and suggestions about testing method and evaluation of test results are given.

Jan 1, 2010

By T. Matsui

Many existing bridge abutments on the soft ground laterally move and their many damage examples have been reported. An essential cause for the troubles of the lateral movements may be the lack of examinations for the lateral earth pressure acting on its foundation piles. In the present paper, actual movement condition of existing bridge abutments is first summarized, and then the author establishes a practical and systematical design method for bridge abutment foundation piles, including the examination for the passive pile.

Jan 1, 2010

By D. J. Ketkar

It is a frequent experience to find that the Sub-surface Investigation (S.I.) data is either inadequate or misleading. However, such cases are rarely reported. Nonetheless, the projects suffer on-account of delays, cost-over-runs, disputes and/or compromise of the safety norms. Many times S.I. is considered unnecessary or is carried out as a ritual, mainly due to (i) non-availability of good S.I. agencies, or (ii) absence of Geotechnical consultant, or (iii) shortage of time. Importance of S.I. cannot be over emphasised. Yet the profession is in a state of confusion - mainly because of lack of competent professional agencies and of well-defined roles/responsibilities of the concerned parties. In this paper, some suggestions are made to get better returns from the S.I. activity.

Jan 1, 1996

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By S. L. Karunakaran

There are cases where it is found that a raft foundation would have adequate factor of safety against ultimate bearing capacity failure but the settlements would be excessive. Piles may be introduced in order to limit settlements to an acceptable level. The actual number of piles required to reduce the settlements to an acceptable level may be very small compared to the number of piles required to transmit the whole structure load. The paper focuses on the difficulties encountered in evaluating the load sharing between raft and piles. An elaborate analysis taking into account the interaction between raft, piles and soil is very complex and time consuming. Few approximate methods for arriving at a satisfactory solution to piled raft system are discussed in the present paper.

Jan 1, 1996

By R. K. M. Bhandari

Geotechnical investigation for a LPG plant located in Assam state - an area of high seisimicty - revealed a layer of loose to medium silty sand susceptible to liquefaction at some depth below the finished ground surface. Liquefaction analyses were carried out using simplified Seed's approach as well as considering the progressive buildup of pore pressures with cyclic earthquake loading. Seismic settlements were computed for areas where the analysis indicated partial liquefaction. Pile foundations in areas where complete liquefaction was indicated, were treated with gravel drains to prevent buildup of pore pressures. The paper presents and discusses the liquefaction analyses, effect of non-liquefiable overburden soil on the liquefaction potential of the silty sand and the remedial measures that have been taken to ensure safety of the pile foundations in transmitting vertical and lateral loads.

Jan 1, 1996