Search Documents

By Jennifer Peirce Brandt

Project documents and the United States Army Corps of Engineers? permit for construction of the Stemmers Run Relief Wastewater Force Main across the Back River in Baltimore County, Maryland specified a minimal width, steel sheet pile cofferdam and a 12 feet wide, pile supported, timber decked, causeway trestle ? both approximately 1700 feet in length. Due to the impractical width of the causeway, the contractor desired to combine the cofferdam and the causeway structures in order to minimize wetland disturbance and maximize access for construction equipment. The resulting support structure was a steel sheet pile cofferdam, approximately 17 feet wide, internally braced, and capped with transverse timber deck mats to serve as the access and work trestle for the trench excavation, pipe bent construction, and trench backfill. Construction of this cofferdam/causeway progressed from the north shoreline toward the middle of the river. Then, working back toward the north shoreline, the contractor excavated, installed the 54 inch diameter pipe and H-pile support bents, and backfilled the trench in increments of approximately 60 linear feet. Excavation spoils from one section were used to backfill the preceding section. As the pipe installation progressed toward the north shore, the steel sheet piling and timber deck were removed. As sufficient sheet piling and deck mats were removed, the contractor began the process anew from the opposite shoreline using the reclaimed materials. The project was complicated by the presence of deep, very soft, weight of hammer, silts and organic clays and an unbalanced, hydrostatic head of 20.5 feet. In addition, concurrent pile driving, excavating, and backfilling in successive cofferdam sections required the use of heavy, long reach, hydraulic backhoes, and a 200 ton capacity crawler crane which controlled the design of the timber causeway deck and its supporting sheet piles.

Jan 1, 2008

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Brett K. Mainer

In the summer and fall of 2007, Drill Tech Drilling and Shoring, Inc. designed and built three 24-foot inside diameter shafts in Northern California using soil mix panels for support. The soil mixing was performed using the Bauer Cutter Soil Mix (CSM) method, by which rectangular soil mix panels up to 71 feet deep were arranged in an overlapping manner to form a 24-foot inside diameter circle. The shafts were then excavated to depths up to 51 feet. One of the shafts was a test shaft and used only the soil mix panels for support. The other two shafts were located immediately adjacent to the Mokelumne River and were used as access pits for a microtunnel drive under the river. These two shafts had wide flange beams embedded in the panels and were supported with several levels of ring steel placed during excavation. This project was the first use of the Bauer CSM method in the United States. The CSM method has been used extensively in Europe and Asia, but never for this application and never with this high a loading criteria due to water head and microtunnel reaction forces. Soil conditions at the river crossing shafts consisted of sands, gravels, and cobbles over top of sandstone and conglomerate bedrock ranging in strength up to 5,000 psi. Groundwater was within several feet of the surface. The shafts were successfully completed between October 2007 and January 2008, and the microtunnel was successfully completed in February 2008. This paper provides discussion regarding selection of the shoring type, structural design, the soil mixing method, and the mix designs. Shaft construction, shaft performance, and the capabilities of the CSM equipment are presented.

Jan 1, 2008

By Avi Shonberg

With the advancement of offshore wind farm projects towards deeper waters and larger wind turbine generators, founda- tion solutions other than the monopile have received increasing attention over the past 5 years. Monopiles are the most commonly used foundation solution for offshore wind turbines, with 82% in European waters founded on monopile foundations (EWEA, 2019). However, 2018 saw a record number of suction bucket jacket (SBJ) structures, which consist of a three-legged jacket sup- ported by a suction bucket at each leg (Figure 1), installed for offshore wind. applications. SBJs have now been installed successfully at the Borkum Riffgrund 1, Borkum Riffgrund 2 and Aberdeen Bay offshore windfarms. Suction-installed foundations, referred to in this paper as suction buckets, suction caissons, suction piles or suction anchors, have been widely used in the offshore industry since the early 1980s for a range of offshore applications predominantly as anchors for floating offshore structures - where they are "the most widely used anchor types for deep-water mooring applications" (McCarron, 2011). Suction buckets, installed using pumps that generate suction forces by creating a pressure difference between the inside and outside of the bucket, allow for the installation to be undertaken with minimal noise and without the use of mechanical force. Therefore, a key difference between suction-installed foundations and other foundation types is that the installation design, which must consider the soil type, soil strength and installation specific risks (for example, soil stratification with significant differences in permeability) may have a direct influence on the dimensions of the foundation. While the number of SBJS installed for offshore wind applications has increased significantly in recent years, the installation process for SBJ struc- tures is yet to become standard practice and is considerably more complicated than the installation process for mon- opiles. This paper provides a brief

Jul 1, 2022

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Edward C. Clukey

"Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed.During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor’s QA/QC program should be increased to achieve a foundation system with the required level of reliability.Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially “at-risk”. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.IntroductionThe foundation support system for the process train at a major LNG facility comprises more than 6,000, 23-m long DMM elements. The general subsurface stratigraphy at the project site comprises (from the ground surface): (i) up to 8 m of fill sand initially placed underwater building to a stable construction platform; (ii) up to 12 m of soft organic clay (Unit II clay); and (iii) clayey sand and sand layers becoming progressively denser with depth (Unit III sands). Each DMM element comprised two secant 1.5-m diameter DMM columns. DMM elements were typically arranged as cells enclosing one, two, or three DMM elements."

Jan 1, 2017

By Alberto Carmona Rosell, Sri Ram Ramankutty

"The installation of Bored Piles and Diaphragm Wall under slurry using tremie raises quality concerns on the integrity of concrete. It is vital to understand the effects on concrete integrity during concrete pouring process. This paper intends to unveil to what extent the compressive strength of the concrete pour is affected in contact with drilling fluid still. Another important angle of analysis proves whether the inclusion of solids particles of un-hydrated fluid could have impact on the concrete compressive strength. The testing comparing the response of concrete compressive strength when drilling fluid is included into the concrete mix altering the water/cement ratio by 5%, 20% and 30%. Comparative results are analysed between two different hydrated slurries namely sodium activated Bentonite and 3rd generation synthetic polymer.1. INTRODUCTIONSoil stabilization is the base for a successful deep foundation execution. The G3 System Slurry developed by Ground Engineering Operations (GEO), with its third generation polymer, namely PolyMud®, is an innovative and unique alternative to the mineral based slurries for soil stabilization, enhancing the quality and integrity of the underground foundation structures. It optimises the production rate of work progress and cost as well. At the same time, PolyMud® slurry is proven to be environmentally friendly.Guaranteeing the maximum quality of the foundation elements according to the initial design is one of the most important objectives and a concern for the foundations contractors. In order to fulfil the project expectations in this aspect, any incident that could compromise the designed concrete integrity and capacity must be avoided.GEO, has carry out its own research regarding effects on the concrete compression results if drilling fluid intermixes with fresh concrete while pouring. To shed light in this regard, GEO, in collaboration with CML (Concrete Materials Laboratory) Sdn. Bhd., carried out empiric tests that analyse this particular event from different perspectives, bringing up the corresponding results that will be studied and commented in this article."

Jan 1, 2015

By Yoshinori Kurumada, Tatsuo Nagatsu, Keiji Uchida

"Cement deep mixing method has been utilized in the process of construction of an underwater tunnel in Singapore. The soil was improved by this method to prevent undesirable heaving of the soil below the excavated area. Quality control experiments approved the effectiveness of CDM method in increasing the strength of the soil and prevention of undesired heave of the ground. The process of the construction of this project and the quality control experiments results are discussed in this paper.INTRODUCTIONThe Marina Coastal Expressway is a 5.3 km long underwater highway tunnel with five lanes in each direction. It mostly comprises a twin box culvert structure (53.3 m exterior width and 10.89 m height) and was opened by the Land Transport Authority of Singapore (LTA).The contract zone C485 was the most challenging area of the construction; it involved a 700 m long underwater tunnel of which 400 m was built beneath the seabed at the mouth of the Singapore River. A double steel pipe sheet pile wall was built as a temporary cofferdam to keep water out of the excavation site, and the cut-and-cover method was used for excavation. In order to ensure a sufficient cross-sectional area for the flow of the Singapore River, the construction was divided into two phases focused on the left bank (Stage 1) and right bank (Stage 2).The Cement Deep Mixing (CDM) method was used to improve the ground, which comprised soft marine clay, to ensure safety during the excavation. The efficiency of this method in increasing the soil’s strength was approved previously. The design standard strength was quck = 800 kPa. Based on the study conducted after the construction, the average the Unconfined Compression Strength (UCS) of the soil stabilized by the CDM method was quf =3,000 kPa. This paper discusses the effect of the CDM soil improvement construction on the reduced displacement from the excavation and the quality control of the soil improvement."

Jan 1, 2015

By Alan Christopherson

Nearshore construction projects often require installation of steel piles and specific methodologies of installing piles may adversely affect nearby species of concern. Water is an uncompressible medium which allows for easy transmission of energy through the water column. Energy transmission through water depends on the following factors for pile driving: 1) direct contact of the pile and the water; 2) the depth of the water column; 3) the size of the pile; 4) type of hammer; and 5) the energy of the hammer. Seasonal restrictions are usually the best practicable alternative for reducing habitat impacts when pile driving activities may adversely affect the species of concern. When seasonal restrictions are not practical other options need to be evaluated, including mitigation and noise attenuation devices. The broad array of mitigation options will not be discussed as part of this presentation but instead will focus on noise attenuation technologies. Dewatered cofferdams can be effective noise attenuators as they eliminate direct contact of the pile with water while driving. Also, introduction of a compressible medium, like air, near the energy source can provide sound energy attenuation. An unconfined bubble curtain is relatively inexpensive but is not effective in tidal marine projects or rivers and may have unacceptable secondary effects. Secondary effects must be evaluated as these can increase exponentially for larger projects. Secondary effects to the environment include air quality degradation from air compressor use, transportation costs for fuel and equipment, and the potential for injecting oily compressed air into the water column. The confined bubble curtain works well in nearly all environments. It usually is more expensive initially, relative to an unconfined air curtain, but there is less potential for harmful secondary effects. Generally, seasonal restrictions will be adequate to protect species of concern. However, there are conditions in which mitigation or one of the sound attenuation options should be utilized. Site specific factors, including the amount of energy being imparted into the environment, sensitivity of the species of concern, current, accessibility, length of time needed to complete the project, and the cost of the sound attenuation, should be factored into the permit evaluation.

Jan 1, 2013

By Travis A. Shoemaker, Mitchell S. Youmans, Nancy T. Chin, Michael S. Senior

A geologic assessment and stability analysis of the right abutment of Boundary Hydroelectric Dam in Pend Oreille County, Washington was completed in May 2017. The stability analyses identified a potential failure plane of a rock block that supports a bridge abutment, and weight restrictions were established to reduce the bridge loads. To restore full use of the bridge, a long-term stabilization solution was designed. A two-phased construction approach was implemented to reduce risk: (1) cable lashing and wire mesh and (2) 24 permanent post-tensioned tiebacks. The tiebacks were located and sequenced based on stabilization effect and site access to incrementally ease the bridge loading restrictions throughout construction. Due to weight restrictions and site tolerances, all work was performed with rope access construction methods. The contractor’s means and methods, tight drilling tolerances, and an exploratory adit within the rock block made the construction uniquely challenging. Due to limited exploratory data and irregular rock face geometries, the design orientation, location, and tolerances of the tiebacks were established in a 3D Building Information Model (BIM). The 3D model was revised frequently during construction to 1) model the as-drilled conditions of the tiebacks; 2) compare with the remaining proposed anchors; 3) anticipate the contractor’s sequence to reduce risk during drilling; 4) accommodate the contractor’s requests for information; 5) make design changes based on field observations; and 6) incrementally assess rock block stability. The 3D model was created using BIM software and automated using custom programming to link per-plan, proposed, and as-installed tiebacks between the 3D model, field logs, and a stability analysis. This system allowed for a near real-time 3D model and stability analysis, which were easily communicated between the design team and field staff. This workflow and automated model nearly eliminated manual editing of the 3D model, accelerated contract document response time, and helped reduce risk for the owner, contractor, and engineer. Here, we present a successful case study utilizing the Observation Method and a real-time 3D model to complete a project with numerous complexities relating to design, communication, and risk.

By Ana Pereira, Naomi Norris, Donald Bruggers

The city of Christchurch, New Zealand is predominantly founded on alluvial sediments consisting of interbedded layers of loose to medium dense sand, soft to stiff silt and clay mixtures, and pockets of organics. These soil deposits have high liquefaction potential. Following the 2010/2011 Canterbury Earthquake Sequence several ground improvement trials were undertaken within Christchurch to understand the effectiveness of different types of ground improvement in these silty sand geological conditions. This paper presents a discussion of a stone column ground improvement trial undertaken at a Christchurch site with high fines content soils. Stone columns were installed using two types of installation methods and a range of Area Replacement Ratios (ARR) to assess the effectiveness of these ground improvement methods in high fines content soils as well as the influence on the type of installation method. Pre- and post-column installation CPTs, seismic Dilatometer Tests (sDMTs), cross-hole shear wave velocity tests, and plate load tests have been undertaken to assess the effectiveness of the ground improvement. Results of the testing are presented in this paper. INTRODUCTION This paper presents the results of a stone column ground improvement trial undertaken in Christchurch, New Zealand (Fig.1). In 2010 and 2011, four large earthquakes (greater than magnitude 5.9) and thousands of smaller aftershocks occurred in the greater Christchurch region. These events are referred to as the Canterbury Earthquake Sequence (CES). Liquefaction occurred across large portions of the city during the stronger earthquakes, particularly the February 2011 event. Following the CES a large amount of data was collected across the city including the location and volume of sand boils, and the location and magnitude of ground cracks. Additionally, data from thousands of ground investigations have been uploaded into a public database. As a result, there is clear evidence that silt and silty sands liquefy in addition clean sands. The CES and resulting liquefaction motivated a series of studies and trials from different organisations aiming to better understand the available technologies for liquefaction mitigation. The subject of this paper is a ground improvement trial undertaken by a local contractor specialising in deep foundations and ground improvement. They were interested in understanding the effectiveness of stone column ground improvement in high fines content (silty) soils using two different installation techniques, vibratory and non-vibratory. Different arrays and Area Replacement Ratios (ARRs) were used for each of the two methods of columns installation.

Jan 1, 2019

By Patrick J. Lydon, Gregory A. Terri

"The recently opened Mansueto Library at the University of Chicago campus was a 2012 OPA runner-up. The dramatic elliptical shaped dome of this structure tells only part of this structure’s story. The underground automated storage and book retrieval system below ground required excavations as deep as 55 ft (17 m). The system that allows the University to store many of its publications well below grade also required an approximately 50 ft (15 m) clear span for the perimeter walls between the lower level and street level slabs. The latter requirement allows the conveyors to operate freely to retrieve and transport publications up to the lobby level. The design-assist-build team worked together to develop the most cost-effective solution for below-grade work in this challenging urban and geologic environment.The perimeter of the new oval-shaped library is over 620 ft (189 m) long and sits in a central location on campus—adjacent to the Regenstein Library and two city streets and the Henry Moore sculpture, which commemorates the location of the first self-sustaining controlled nuclear reaction. The new library construction not only had to meet challenging structural and geotechnical requirements, but also had to be sensitive to its active and historic surroundings. The soils at the site consist of about 25 ft (7.6 m) of sand, followed by lean clay, generally increasing in stiffness to the top of the dolomitic limestone. Five to 10 ft (1.5 to 3 m) pockets of saturated sand also lie on the north side of the site at about 45 ft (13.7 m) below grade. The top of weathered rock varies in elevation from 59 ft (18 m) below grade in the south to 69 ft (21 m) in the north. There is 1 to 2 ft (30 to 60 cm) of weathered rock. Groundwater at the site is about 7 ft (2 m) below grade.The new structure would extend 55 ft (17 m) below grade through saturated sand strata and into weathered rock for part of the structure’s footprint, so it was critical that the new permanent retention system minimize groundwater seepage laterally through the structure’s wall as well as piping through the weathered rock below the structure. The perimeter walls had to be very stiff to minimize ground movement around the structure’s perimeter due to the significant clear span between slabs."

Jan 1, 2013

By Jeff Starchuck, Harald Kullmann

"In 2005, an inspection showed that the Deception Bay Wharf in the Canadian Arctic was at the end of its service life. Although Deception Bay is closed with landfast ice up to 5 ft thick, shipping operations continue year-round, with additional voyages in the summer open-water season to supplement mine supplies. The rehabilitation scheme that allowed minimal interruptions to shipping involved concrete caissons cast on barges and an ingenious placing system.WorleyParsons Westmar of Vancouver, B.C., performed the inspection under contract to the owner, Xstrata Nickel, Montreal, Quebec. The wharf, on the coast of the Nunavik region of Quebec, was originally constructed in 1971 for an asbestos mine, and is now used to support Xstrata’s Raglan nickel mine, importing fuel for p o w e r g e n e r a t i o n a n d general mine supplies, and exporting nickel concentrate to smelters in the south. Emergency repairs were essential to allow operations to continue at the site, while the parties considered permanent rehabilitation options and secured funding. The repairs were done in the openwater seasons, and included reinforcing the failed interlocks above water level with steel patch plates and injection grouting of the cell fill below the port crane in 2005. In 2006, workers installed a circumferential belting system below water level.Westmar held critical planning sessions with the mine operation personnel to find ways to stretch the limits of the mine supplies and nickel storage facilities. In the end, the parties agreed to shut down construction activities four times during the ice-free season to allow access to the dock site.Westmar developed a plan that allowed mine operations to continue during construction, and Xstrata approved the plan and budget in September 2006, for execution in 2007. Rapid construction was essential. To accommodate the short construction season and maintain minimum levels of service for the mine, the work was radically different from conventional Arctic deep-sea port construction. Like the original Deception Bay Wharf, construction practice was to use steel sheet pile circular cells with the consequential heavy support services for the labour force. Construction duration was typically two seasons. The plan for Deception Bay was executable in one season based on a concrete caisson structure. Only a modest amount of schedule float was needed."

Jan 1, 2009

By Rouzbeh Vakili, Adel M. Hanna

"The application of piled raft foundations has significantly increased during the last few years. In this system, the raft and the pile group collectively transfer the applied building load to the underlying soil layers. Determination of load sharing between the raft and the piles derives the complexity of piled raft designs due to its multi-parameter nature. These parameters are but not limited to: soil density, pile length, pile spacing, raft geometry, and piles installation technique. This study is to examine experimentally the effect of sand density and pile installation techniques on the load sharing mechanism. Experimentally, tests were conducted on a square rigid raft with a single pile in sand under three different soil densities; 30%, 45%, and 60%. The experimental results are used to determine the pile and the raft shares in non-displacement and displacement piled raft systems. The results of this study reveal that soil density changes the load sharing of displacement piled raft; the pile share increases in higher soil density. However, this is not the case in non-displacement piled raft and load sharing is independent of soil density in working loads.IntroductionThe piled raft foundation is a combination of shallow and deep foundation which transfers the superstructure load to the soil by a complex soilstructure interaction. The interacting mechanism among foundation elements and their surrounding soil is illustrated schematically in Figure 1 and could be classified into two categories: (1) pile-soil-pile and (2) pile-soil-raft. The pile-soil-pile interaction is the same as the free standing pile group and is a function of pile spacing and pile installation method. Pile-soil-raft interaction, which only involves in piled raft foundation design, could be affected by: the length, spacing, and roughness of the pile, the rigidity and dimension of the cap, soil condition, and the pile installation method. Pile-soil-raft interaction could have favourable and unfavourable effects on bearing capacity and settlement, respectively. The pressure between the cap and the soil favourably increases the horizontal stress on the pile shaft and consequently increase the shaft resistance. Whereas, this pressure induces negative skin friction on the piles which increases the settlement. The pile-soil-raft interaction mainly controls the load sharing mechanism of piled raft foundation when pile spacing (S) is more than 3.5dp."

Jan 1, 2017

By Fabio Santillan, Michael F. Zoccola

"Wolf Creek Dam and Lake Cum berland in Russell County Kentucky is operated by the United States Army Corps of Engineers (USAGE) Nashville District It is a combination 3,940 ft long (1,200 m) non-zoned clay embankment, a maximum of 215 ft (65.5 m) above top of rock and 1,796 ft long (547 m) concrete gravity section. Built in the 1940s, the limestone beneath the embankment is characterized by an extensive interconnected network of solution feature; varying from fist size to largecaves.In 2005, studies conducted by the Nashville Distrect concluded that a new seepage cut-off wall was needed as the existing cut-off wall, installed in the 1970s, did not go deep enough and did not extend laterally far enough to intercept all major karst features The dam was classified as a ""Dam Safety Action Classification I (DSAC 1) – Urgent and Compelling,"" the highest risk under USAGE risk category rankings. Also in 2005, under a USAGE risk screening program of its entire dam portfolio, Wolf Creek was classified as a Dam Safety Action Classification 1-Urgent and Compelling, which put it in the highest category. In 2007, an Independent External Peer Review from outside USAGE, concluded there was compelling evidence that a piping failure mode had re-initiated and was in an ""advanced continuation"" stage of development.Impounding approximately 6 million acre-ft (7.4x102m3) of water at flood storage, Lake Cumberland is the largest reservoir east of the Mississippi River and ninth largest in the United States. Catastrophic failure would result in widespread flooding, Ices of life and economic losses in billions of dollars.In 2008, the Nashville District partnered with a joint venture between finns Treviicos and Soletanche (ISM through a ""Best Value"" contract to construct a new seepage barrier wall. This acquisition method was used in lieu of a low bid contract due to complexity of the work and dam safety concerns. It took advantage of the experience and innovation of contractors by soliciting technical proposals that were evaluated independent of cost. Those proposals deemed technically qualified and responsive then underwent a trade-off analysis between ccst and technical approach and a selection was made of the one deemed to give the best combination."

Jan 1, 2013

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"The use of steel screw piles has greatly increased in recent years because of the advancement in the installation mechanism and its performance under compressive, uplift and lateral loads. In a steel pile system, the strength of pile material limits the end bearing resistance of the pile due to strong subsurface conditions. The installation mechanism of screw pile can reduce the end bearing resistance due to the torque and axial force. However, if the installation mechanism does not reduce the bearing resistance of the pile, another important factor that can reduce its performance is the strength of the helix/wing plate. In this study, the effect of wing plate deformation on the performance of single helix/wing plate pile bearing resistance investigated. A model ground was used to investigate the effect of wing plate deformation. Dry Toyoura sand was used as a ground material and was compacted to denser states of 80% and 92%. The shaft and wing plate material of the pile was the same to actual piles that are used nowadays in Japan. A series of load tests were performed with different wing plate diameters and thicknesses. It was observed that deflection in the wing plate reduces the bearing resistance of the pile. The increase in the thickness of the wing plate was seen to restore the reduced pile resistance due to deflection. It was also observed from the experimental results that the ratio of wing plate diameter to shaft diameter (Dw/Ds) greatly affects the deformation of wing plates, which ultimately affects the end bearing resistance of the pile. The results obtained in this research suggest that the outstand length (Lw) of wing plate should be less than 5.6 times the thickness of wing plate for piles having a large Dw/Ds ratio under strong ground conditions.INTRODUCTIONThe first use of screw pile was almost 180 years ago by Alexander Mitchell. He patented his invention in 1833 with the name “Screw Pile”, and used it for ship moorings. The use of screw piles has since been adopted in various areas such as lighthouses, fencing for agriculture and marine structures. The use of screw piles in civil works started in 1985, after the invention of the hydraulic torque motor, as it eases the installation process. Nowadays, screw piles are used in the foundation of transmission towers, elevators, buildings and many other civil structures.Screw pile has an edge over other steel pile systems due to its high bearing, uplift and lateral resistance. The end bearing resistance of screw pile depends on installation, strength of subsurface material and the pile material. The screw pile is installed by applying torque and axial force. The pile torsional strength should be more than the applied torque and axial force to avoid deformation before reaching the final depth."

Jan 1, 2015

By Matthew D. Marks

"The Sacramento Area Flood Control Agency initiated the Natomas Levee Improvement Program in 2006 which would bring the entire 42 mile Natomas Basin perimeter levee system into compliance with applicable Federal and State standards for levee protecting urban areas. The soil-bentonite slurry cutoff has been utilized as the primary construction method for addressing the under seepage deficiencies. To date, a combined total of over 4,500,000 square feet of slurry cutoff wall have been constructed utilizing excavation methods to a maximum depth of 75 feet and deep soil mixing methods to a depth of 90 feet. The construction of these cutoff walls has required the use of newly designed and custom built long boom and stick attachments for large hydraulic excavators and additional resource will be required to complete future phases. Key components of the NLIP program have included advancements in the development of soil-bentonite backfill mix designs, specified ranges on the soil backfill gradation to address concerns of long term consolidation of the backfill material, evaluation of the trench slurry filtrate loss with regard to cutoff wall acceptance, maintenance high slurry densities to provide greater trench stability, and continued development of backfill mixing procedures.IntroductionThe Natomas Levee Improvement Program (NLIP) was initiated by the Sacramento Flood Control Agency (SAFCA) in 2006. The long term objective of the NLIP is to provide 200-year level flood protection to the basin. To date, approximately 21 of the 42 mile Natomas Basin perimeter levee system has been completed, totaling over $100,000,000 in construction contracts, of which slurry cutoff walls make up approximately $25,000,000. Other construction elements include excavation and removal of unsuitable levee materials, raising or widening existing levees, construction of landside seepage berms, drainage canals, and miscellaneous structures.Although each construction phase of the NLIP includes various construction elements of levee restoration program, the slurry cutoff wall is the primary construction element for addressing the under seepage deficiencies. To date, approximately 4,500,000 square feet of slurry cutoff walls have been installed using excavation and deep soil mixing (DSM) methods. This includes approximately 2,000,000 square feet of slurry cutoff wall along 5 miles of the NCC South Levee and 2,500,000 square feet of slurry cutoff wall along 16 miles of the Sacramento River East Levee (SREL). The work has been completed under 8 separate contracts, through SAFCA, and performed between September 2007 and December 2012. A summary of the contract phases and associated cutoff wall square footage is provided in Table 1. Most of the work has been performed within the seasonal dry weather period in the Sacramento valley, which occurs between April and October. This has required much of the work to be performed on an aggressive construction schedule, year after year."

Jan 1, 2017

By P. D. Arumairaj, B. Vani

"Micropiles are small diameter cast insitu reinforced grouted piles and it has been effectively used in many applications of ground improvement. It increases the load carrying capacity of soil and reduces the settlement. It is also used in strengthening existing foundations. In this study, the effect of Solid and Hollow micropiles on the load carrying capacity of footing resting on sand is studied. The effects of solid Micropiles are investigated by conducting experimental model studies. The parameters involved in this study include the position of pile, pile length and pile spacing. Load test was carried out on a model footing resting on sand with solid and hollow micropiles. Load test trail is repeated for footing on Micropiles with varying lengths of 10, 20, and 30 times the diameter and spacing equal to 5, 4, 3, 2 times the diameter. The load-settlement behavior of each case is compared. Optimum length and optimum spacing of both the solid micropile and hollow micropile are determined. It is also observed that the effect of micropiles in the peripheral of footing resists lateral displacement of soil underneath the footing. The micropile beyond significant depth becomes redundant.INTRODUCTIONA micropile is a small diameter (less than 300 mm) drilled and grouted pile that is typically reinforced - FHWA-NHI 2005 (Federal Highway Administration-National Highway Institution). It is constructed by drilling a borehole, placing a steel reinforcing element into the borehole and grouting it. Hollow micropiles are typically reinforced by solid central bar that occupies about onethird of the hole volume. The grout is placed by gravity, under pressure methods or by a combination of both (post grouting). Thus, micropiles can be considered as small drilled-shafts that are specially drilled and grouted.Historically, micropiles have been introduced in Italy as a foundation system mainly for retrofitting and underpinning of structures that had sustained damage during World War II and access for conventional piling equipment was not possible (Bruce, 1988). The second generation of micropiles is a pressure grouted piles with a central mono all thread bar (with diameter up to 89 mm). They are installed by using either an open or cased hole drilling method.A new generation of micropiles, termed Grout injection bore micropiles (IBOR), was developed in the 1980s. The IBOR, currently named hollow bar micropiles, utilizes a continuous all-threaded hollow steel bar as the drilling and grouting conduit, which allows drilling and grouting simultaneously without the need of a casing during drilling. A sacrificial (lost) bit with openings that allow for pressure grouting of the hole is threaded onto the end of the hollow bar and is left in place following drilling. A drilling fluid (air, water, or grout) is introduced through the hollow bar and allows the spoils to flush from the borehole opening. Upon reaching the required depth, neat cement grout is then injected under high pressure into the drilled hole to fill the annulus between the bar and the soil from the bottom to the top. Due to the grouting method employed, the shape of the hollow bar micropile is expected to have a bulb shape with an enlarged base."

Jan 1, 2015