Search Documents

By Carl-Oscar Nilsson, Åke B. Nilsson

"The embankment dam at Storfinnforsen is 23 m high and was completed in 1954. The dam has an impervious zone with timber sheet piles and a support fill of glacial till. The pore water pressure in the downstream shoulder has during recent years increased due to deterioration in the sealing function of the timber sheet piling. There is a concern that the high pore water pressure in the glacial till will cause internal erosion initiating at a thin coarse transition layer between the glacial till and the rock fill along the downstream toe. As a remedial action in order to improvement of the leakage resistance a supporting berm of coarse rockfill against the downstream slope of the dam was constructed in year 2013. In addition a new impervious seal in the centre of the dam e.g. a diaphragm wall was considered. However, after further studies and a trial stretch of 40 drains each 20 m long and diameter 0.3 m an alternative with vertical drilled drains in the downstream support was selected. A contract has now started up to drill in a similar way to treat the full length of the dam with drains. The work is in the planning to be completed in 2016.Dam ConstructionStorfinnforsen Embankment Dam was put into operation in 1954. The dam is 330 m long and maximum height is approximately 23 m. The dam is constructed with a central core zone and supporting zones of earth and rockfill on the upstream and downstream sides giving an almost symmetrical cross-section about the dam axis, see Fig. 1. The upstream slope is 2H:1V down to el. 270 and 2.5H:1V below. On the downstream side the slope is 1.75H:1V down to +269 and 2H:1V below. The core zone consists of a timber sheet pile wall with a Zone 5 of glacial till, approximately 2 m wide, adjacent to the wall on the upstream side."

Jan 1, 2016

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By Gerald Verbeek, Erick Baziw

Stone columns are used in geotechnical site remediation to increase load-bearing capacity and reduce settlement of foundations. Stone columns also improve slope stability and increase the shear strength of a soil. A very challenging problem is to characterize the in-situ shear wave velocities from data acquired from Downhole Seismic Testing (DST) after the insertion of stone columns. DST is an important geotechnical testing tool for site characterization that provides low strain (<10-5) in-situ interval compression and shear wave velocity estimates, but the postanalysis of seismic data acquired from DST in the presence of stone columns is very challenging due to the resulting complicated in-situ soil conditions. To obtain the right results it is necessary to use an algorithm that incorporates source wave raypath refraction. Starting with the Normal Moveout Seismic Cone Tomographic Testing (NMO-SCTT) algorithm developed some years ago, this paper outlines the modifications and additions made to this NMO-SCTT algorithm to facilitate stone column site characterization. To dramatically reduce the optimal solution space for the estimated interval velocities the paper also described a priori conditions that are applied based on the unique nature of the stone column site conditions.

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014

By B. De Paoli

At Pietrafitta, between Assisi and Perugia, ENEL (Italian National Electricity Authority) has for some time been managing a power-station operated with lignite, mined from an open mine on the way to exhaustion. A new plant is under construction which is located in the mine that was filled with tailings, mainly clays, sandy silts, lignite and ashes produced by the power-station. The soil profile is shown in Fig. 1: the thickness of the made ground is around 27 m. The foundation of the new power-station is on 320 t piles, 1.20 m diameter, embedded in the cohesive base formation at a depth of 57.5 m. 2,350 piles will be constructed for a total length of 125 km. It is therefore one of the largest pile sites at present in operation in Italy. [ ]

Jan 1, 1994

By Amr Sallam, David Thompson, Moataz Hassan

"The Little Lake Harris (LLH) Bridge was constructed in 1951 to replace the eastwest County Road 48 Bridge connecting the towns of Howey-in-the-Hills and Astatula in Lake County, Florida, United States. The 78-span bridge carries two lanes of traffic, is 3,130 feet long, and 36.1 feet wide. The concrete deck is supported by steel I-girders carried by one row of 18-inch square precast concrete driven pile. In the late 1980's, slight settlements were observed in several bents. In 1990, Florida Department of Transportation (FDOT) initiated annual survey of deck elevations during bridge inspections to monitor settlement. Due to the slow nature and magnitude of settlement, substructure instability was not a major concern to the department. However, public concern over the settlement and rough ride of the bridge continued to rise. FDOT contracted Kisinger Campo & Associates Corp. (KCA) to provide the needed design to correct the dips in the riding surface and minimize future settlement. KCA's initial design was based on the concept of ""helper bents"" at the settled bents in order to restore the bridge to original elevation. Estimated construction cost for seven helper bents was about $3.3M. FDOT requested evaluating other alternatives to reduce the cost of the bridge restoration. KCA involved the geotechnical consultant, Terracon Consultants, Inc. (Terracon), to perform a peer review and provide an economical alternative solution. Jacking and shimming the bridge was determined to be both technically viable and economical with a total cost of less than $300K. The design was completed in March 2010 and construction was completed in February 2011. This paper provides an overview of the LLH Bridge history, summarizes the evolution of the design methodology including the findings of the geotechnical study and presents lessons learned during the design and construction of the project.INTRODUCTIONThe Safety and Preservation of the State Highway System is the top priority of the FDOT. Therefore, FDOT initiated a bridge management program that starts with conducting biennial safety inspections performed by Certified Bridge Inspectors (CBI). The inspection reports together with the CBI’s recommendations are reviewed by a registered Professional Engineer (PE) and work orders are issued with priority ranking depending on the severity of the bridge deficiencies. If the scope of work is considered beyond the in-house crews’ capability, the work is then included in a contract for and bid. LLH Bridge was a little different. It was initiated in direct response to number of complaints the FDOT District 5 Structures Maintenance Office (D5SMO) received regarding settlement of the Little Lake Harris Bridge."

Jan 1, 2015

By Mark Spence, Tom Lardner, Matthew Janes

"IntroductionThe design-build method streamlines project delivery through a single contract between the Contract manager and the design-build team. The design-build method places emphasis on collaborative project management between design and construction disciplines to minimize project schedule, reduce costs, encourage balance risk amongst the design-build team. Since 1985, the percentage of nonresidential design and construction projects has increased from 5% to 45%.1A project carried out in Edmonton, Alberta, Canada will be used as an example to illustrate the challenges of the design-build project delivery method and the merits of establishing a GBR. The project involved a complex slope stabilization as part of an extensive freeway widening. At the project location the roadway was being widened within the base of a historic stream valley into a steep slope with a history of a previous slope failure. The slope was to be steepened through the installation of a series of 14 interlocking arc structures constructed half way up the slope. Access and schedule proved critical to the successful completion of the project.Geotechnique and Site HistoryThe geotechnical investigation undertaken for the site included six boreholes drilled at the crest of the slope to depths ranging from 14.5 m to 30.2 m. Laboratory testing of the soil samples included direct shear tests, Atterberg limits and grain size analysis. The geotechnical report also referenced a previous geotechnical investigation that was carried out in response to a failure of the slope in 1971."

Jan 1, 2015

By Leena Korkiala-Tanttu, Ilkka Vähäaho, Juha Forsman, Paavo Lahdenperä, Kalle Rantala, Osmo Korhonen

"District of Arabianranta (Helsinki, Finland) has been founded on an old seabed, which was filled with miscellaneous soil materials. The subsoil consists of very low shear strength clays and organic clays (gyttjas). The soil was moving towards the sea at a rate of 1050 mm/year, because of filling on top of the soft subsoil. In the middle of 1990’s it was decided to build a residential area to Arabianranta, because it is located only 5 km away from the downtown. To inhibit the movement of soil, it was planned to build this 700 m long deep mixed column-wall barrier along the shore of Arabianranta in the years 1997–2005. A lot of instrumentation and inclinometers were analyzed and it was noticed that the column-wall remains at its place and the displacement rate inside the wall has been only 0.44.6 mm/year after construction works. Nevertheless, the displacement of soil at the landward side of the column-wall is still 1.25.1 mm/year. The soil at the seaside of the barrier is also moving towards the sea 12.922.2 mm/year. Another problem might be displacements of soil near the places where the column-wall ends (tails).1. INTRODUCTIONArabianranta district (Helsinki, Finland) has been an industrial, storage and wasteland area for a long time. Developing this area into a residential area was earlier considered too expensive, so it has been constructed during last decade. The organic clay layers (gyttjas), which have weak shear strength and high water content, were covered by various layers of fillings done in different phases. Because of the fillings, the area was not only consolidating, but also moving horizontally 1050 mm/year towards the sea due to the fact that the frictional soil under clay layers slopes towards the sea. A trial deep mixed structure was constructed in 1997 to inhibit the horizontal displacements of soil. The actual construction of the columnwall was completed in 2000-2005 with overlapping deep mixed cement columns on the seaward boundary. The barrier was built so that the horizontal movements would not risk the pile foundations at Arabianranta. The length of the barrier is about 680 m and width varies between 1220 m. There is a great amount of instrumentation near the barrier (inclinometer casings and other measuring devices). All this measuring information has been collected and analysed at 2014 to find out how this deep mixed column-wall has affected the horizontal displacements."

Jan 1, 2015

By Douglas Heenan

The fracture orientations were inferred based on theory and previous experience. The fracture pattern was not monitored during the project. Grout volume was recorded at each sleeve port and real time movement monitoring of the building foundation was performed.

Feb 10, 2003

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 2.5 m to 3.0 m (8 to 12 feet) in diameter and extending over 60 m (200 feet) in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2008

By Giovanni Lombardi

In order to get a clear overview of the grouting works carried out, to avoid misinterpretations of the data and functions shown on the display of the grout monitoring device, it is recommended to keep the flow rate as constant as possible. Obviously, at the beginning of the process, the flow rate will increase from nil to the selected "basic" value. An important question frequently addressed is also how to reduce the flow rate in nearing the GIN limit so to finally reach the target intensity. Depending on the actual conditions, there are different manners to proceed. However, the following one appears to be the most convenient. It is represented on Figure 25. Being GIN the target intensity, two new limits at, let&apos;s say, 0.95 GIN and at 1.05 GIN as shown in the figure should be defined. The selected basic grout flow rate "q0", is kept as constant as possible all along the grouting process until the 0.95 GIN limit is reached. The flow is then reduced step wise to 2/3 q0, 1/3 q0 and zero at crossing each of the three limits. A similar rule can be used in respect to the maximum pressure, while for the maximum volume the process can be stopped at one time. Obviously the number of successive limits and thus the number of steps in reducing the pressure, as well as the width of the fringes defined in said way may be adapted to the local conditions.

Feb 10, 2003

By Peter A. Thompson, Richard E. Prust

"The Bangkok Mass Rapid Transit (MRT} Chaleom Ratchamongkhon Line project is the first underground subway to be completed in Thailand. It consists of 22 km (14 miles) of twin-bored tunnels and 18 cut and cover stations constructed within the deltaic deposits that underlie the city. This paper describes the ground conditions, site investigation, including the use of the self-boring pressuremeter and the associated design issues for the construction of deep foundations. The paper also describes a selection of the various deep foundation solutions that were adopted to address particular constraints of the project and the ground conditions, including slurry walls for the cut and cover stations and foundations used for the underpinning of existing structures.INTRODUCTIONThe MRT Chaloem Ratchamongkhon Line Mass Transit Underground Railway comprises approximately 22 km (14 miles) of tunnels and 18 stations. The route is shown in Figure 1.The project was divided into two design and build contracts. The northern section was awarded to the ION joint venture, composed of Italian-Thai Development PLC, Obayashi Corporation and Nishimatsu Construction Co Ltd. Arup were contracted by ION for the design of the northern section. The section comprises 11 km (7 miles) of twin-bored tunnels, nine cut and cover station tunnels constructed within perimeter slurry walls using top down construction methods, and two cut and cover tunnel structures.The majority of the route of the northern contract follows existing highway Rights of Way. This results in the tunnel alignment passing through the foundations of existing highway bridge structures for which a variety of deep foundation solutions were adopted to underpin these structures.An 8-story park and ride building in the Lat Phrao area was also constructed using deep foundations."

Jan 1, 2005

By Dileej M. Dewaikar, Poonam A. Patil

"In this paper, the ultimate lateral resistance of a long, flexible, unrestrained vertical pile in a cohesive soil is computed under static loading condition using py curves. A simple and improved method for the construction of hyperbolic p-y curves for a cohesive soil is proposed for static loading conditions. An iterative analysis is employed with secant modulus approach, using a matrix method known as moment area method developed by Sawant and Dewaikar. The loadground line displacement relationship is obtained for different load eccentricities using p-y curves developed by Matlock, Georgiadis et al. and the proposed hyperbolic p-y curves for different eccentricity ratios. These values are compared with the values computed from model test performed by Rao et al. and with the limit equilibrium solution given by Broms. The comparison shows that, the results obtained using hyperbolic p-y curves shows a better agreement with the model test data with the maximum difference within 15% using other methods; whereas Broms' limit equilibrium solution shows some agreement with the results based on Matlock's p-y curves.INTRODUCTIONPile foundations are used for jacket type offshore structures, which are subjected to large magnitudes of lateral loads due to lake or ocean waves, winds and ice forces. The failure of a pile-soil system is catastrophic and excessive deflection of the pile creates operational difficulties. In the view of this, bending moment in the pile is required to be predicted in a rationar manner. The p-y concept developed by Reese and Matlock (1956) is popularly being used to estimate the pile top deflection and bending moments.The ultimate lateral load which causes collapse of a pile-soil system is generally estimated using Broms' (1964) method, which is based on limit equilibrium considerations. The p-y curves are basically nonlinear in nature and include ultimate pressure at the depth where they are generated. Therefore, if the lateral deflection of pile top against different magnitudes of lateral load is obtained, it should be possible to obtain the ultimate lateral load from this load-deflection relationship."

Jan 1, 2005

By Ramin Motamed, Anna Panorska``, Joseph A. W. Toth

In this study, a dataset of 145 bi-directional and static load tests was used to evaluate the load-displacement response with respect to unit side resistance for drilled shafts comprising fully and partially mobilized data. A total of 612 unit side resistance curves were calculated which included 52 fully mobilized curves showing a maximum response. A new approach using the double tangent method, is proposed in calculating the maximum unit side resistance from partially mobilized load-displacement data. The double tangent method was applied to each load-displacement response to estimate the ratio of mobilized resistance between the intersecting tangents and peak measured resistance. It is observed that as the mobilization of side shear approaches a maximum, the ratio approaches unity. Using the fully mobilized curves, regression models were developed using correlations between ratios of estimated resistance at the double tangent, peak, and maximum measured responses. Regression models are evaluated for the following factors: predominant soil type and drilled shaft construction methods. Comparisons of calculated and measured maximum values of unit side resistance are compared for each model. Although these factors each influence the load-transfer behavior, a single global regression model including all the data showed promise in yielding accurate results.

By Max Gwynn, Tony Suckling

"The new Wembley Stadium is the most spectacular soccer stadium in the world, built to the highest specifications, using the latest technology and offering visitors an unrivalled match-day experience. Wembley Stadium is the home of English soccer, dating back to 1918 when the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Empire Stadium, as it was originally known, was completed in 1924 in just 300 days and cost £750,000 ($1.4m). It was finally closed in 2000.The new Wembley Stadium, which opened in 2006, features fully covered seats for 90,000 fans and a striking arch that sits above the northern half of the stadium. With a span of 315 m (1040 ft), the 133-m (440-ft) tall arch is the longest single-span roof structure in the world. It supports the entire weight of the northern roof and 60% of the weight of the southern retractable roof. This means there is no need for columns within the stadium and ensures unobstructed views.Multiplex Constructions (UK) Ltd. employed Stent Foundations Limited to construct the £10m ($19m) foundations package for the new stadium. The scope of works for the foundation package included the design and construction of all foundations, including all main works piling, temporary works piles for the arch and roof, and tower crane piles. The scope also included trial piling and pile testing, setting out and removal of spoil.Piles were constructed by using bored cast-in-place techniques with both hydraulic and traditional crane-mounted rigs. Stent also installed sheet-piled walls at three locations to the site’s northern boundary. In addition to the main contract works, Stent constructed a £2m ($3.8m) contiguous bored-pile retaining wall within the demolition and earthworks package (Figure 1). This work was carried out as a subcontractor to Griffith McGee."

Jan 1, 2008

By Oladayo O. Komolafe and Majid Ghayoomi

p-y curves have been used over the years to determine the lateral resistance of piles. This method is popular among practicing engineers due to its simplicity and its ability to determine the slope, displacement, shear force, and bending moment for various depths along the pile. The ultimate lateral load resistance is a key component of p-y curve formulation. The p-y curve formulation by Reese et al. (1974) does not consider the effects of soil’s degree of saturation on theoretical ultimate lateral resistance of the failure wedge. This limits an accurate assessment of the lateral soil resistance near the ground surface and the consequent p-y curves. This paper extends the existing approach for determining the failure wedge in unsaturated cohesionless soils with suction dependency, especially for the depths that are above the water table within the wedge. The modification to the failure wedge analysis was made by considering the variation of the degree of saturation which affects effective stress and lateral earth pressure. Through a set of parametric analyses, the impact of incorporating principles of unsaturated soil mechanics in the estimation of theoretical ultimate lateral resistance is examined, and its implications on lateral pile response are discussed.

Sep 8, 2021

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

May 11, 2007

By Paul M. C. B. M. Cools, Martin Th. van Staveren

In 2010, the 5-years joint industry programme Geo-Impuls started in the Netherlands. The ambitious goal of this programme is to reduce geotechnical failures in our civil engineering projects by half in 2015. In the Geo-Impuls programme over 40 client organizations, engineering firms, contractors, research institutes, and universities are involved. In a risk-driven way, and based on top risks and dilemmas, the participants defined three central development themes. These themes are (1) contracts, for dealing with legal issues, (2) geo-engineering, for dealing with technical issues, and (3) communication, for paying attention to differences in risk perception by the human factor. In total 12 Working Groups contribute to these themes by producing one or more specific tools. These provide practical solutions for how to deal with contractual, geotechnical, and communication issues. The tools include working processes, guidelines, best practices, as well as some instruments. The development of these tools, as well as the available results, will be presented in this paper. From the start, Geo-Impuls embraced geotechnical risk management (GeoRM) as the risk-driven way of working for geotechnical engineering and construction. Over the past years, GeoRM and its supporting tools were already successfully applied in several projects. Therefore, the paper also describes also the GeoRM implementation process, including the quality assurance and control. Finally, the effectiveness of GeoRM will be discussed, by summarizing an analysis of all published geotechnical failures and accidents in construction projects in the Netherlands, which decreased substantially over the past 4 years.

Jan 1, 2017

By Aditi Sharma, Sumanta Haldar

Scouring of soil is the major concern forthe various hydraulic structures built in the flowing rivers since scouring impacts the bearing capacity of foundations. Hence, consideration of scouring in the design of foundations for hydraulic structures is crucial. Pile groups in bridges are subjected to combined vertical and horizontal loading due to self-weight, live loads, vehicular impacts, wind load, earth pressure, and current. Hence, an assessment of the combined bearing capacity of pile groups subjected to scour is essential for the safety of the structure. This paper aims to analyze the bearing capacity of pile group supporting the bridge under combined loading i.e., Vertical (V) and Horizontal (H) loading subjected to local scour. Three-dimensional finite element model (3D-FEM) of a 3 x 3 pile group embedded in homogeneous sandy soil is established in Abaqus (2018). Mohr-Coulomb plasticity model is used for the soil domain. The pile group is modelled as linear elastic. Finally, V-H yield envelopes are obtained with and without scour. The potential impact of different parameters, such as angle of attack, flow velocity, depth of flow, and different pile length-to-diameter ratios (L/D) and spacing-to-diameter ratios (S/D) of pile group on V-H yield envelopes is studied.

Sep 1, 2022