Search Documents

By E. W. J. Thornton

During the past six or seven years extensive research has been performed on ore samples procured at the Bruns1,vick Tin Mines which is located in the south-west corner of New Brunswi.ck. This property was originally staked by Mount Pleasant Mines and they did considerable metallurgical and geological work on a small copper, zinc and tin deposit. In 1969, the property was obtained by the Sullivan Mining Group and after much geological and diamond drilling work, an entirely separate ore body \Vas located two miles south of the previous workings. The major economic metals in this ore zone are tungsten, bismuth and molybdenite, but many other metals exist as well. As the ore contains a host of different mineral species, it can be seen that considerable time WRS required to develop a practical flow sheet.

Jan 1, 1977

By John Frostiak

"Kahama Mining Corporation Limited, a wholly owned subsidiary of Barrick Gold Corporation, poured the first dore bar and filtered the first concentrate produced at the Bulyanhulu mine on February 28, 2001. This event marked the completion of the initial development of the Bulyanhulu Mine – Barrick’s first mine located outside of the Americas.Bulyanhulu is a 2,500 tpd underground mine located in the Lake Victoria gold belt of northern Tanzania. Gold is recovered as a gravity concentrate and smelted on site to produce dore bars or collected in copper concentrate that is shipped to offshore smelters. The facilities were constructed to meet Canadian standards. Unit operations include single stage crushing, SAG milling, gravity recovery, flotation, thickening and dewatering. Tailings are converted to paste and returned underground as paste backfill or pumped to the surface tailing site. The surface paste tailing disposal system is believed to be first of its kind in the gold industry. Paste disposal has several advantages over slurry, including lower dam construction costs, reduced water losses, and lower reclamation costs. This paper describes the facilities and discusses the challenges faced during development and construction including logistics, lack of infrastructure, recruiting and training, security, and social issues as well as initial operating results.INTRODUCTIONBarrick Gold Corporation completed the Bulyanhulu mine development in 2001. Capital cost of the project was US$280 million. The mine produced 241,575 ounces from start of milling to year end at a total cash cost of $197 per ounce. Numerous challenges were overcome in the mine’s development due to the general lack of infrastructure in Tanzania and the mine’s location some 1200 km inland by road from the port of Dar es Salaam."

Jan 1, 2003

By G. R. Addie

"In February, 1975, the President of Georgia Iron Works Company, Mr. Tom Hagler decided to build a new hydraulic laboratory to water performance test all of the companies' centrifugal slurry pumps.Equipment procurement started in March, 1975, by ordering of a mini computer data acquisition system.Work commenced on the lab in July, 1976, by erection of a Butler Building and the laying down of a 20,000 gallon concrete sump.By late October, a facility compromising two water test loops of 8"" and 18"" pipe diameter was in operation carrying out head quantity and suction performance tests on pumps up to 16"" in size.In August of the following year, an 8"" diameter pipe slurry loop was installed to enable pipe friction and deposition velocity of a slurry to be measured in an 8"" inside diameter pipe.With the encouragement of Reserve Mining in Minnesota and IMCC in Florida, this was followed in March, 1978, by the addition of over 300 feet of 18"" diameter pipe to make up an 18"" diameter pipe slurry system complete with head loss and deposition velocity observation sections.The office and shop areas of the lab were again expanded in April, 1978, to provide further expansion to the test sections and staff facilities."

Jan 1, 1980

By Wei Sun, Jaewon Choung, Zhenghe Xu, Zhangming Cui

"High intensity conditioning has been demonstrated in a number of cases to enhance fine particle flotation. The improvement could be attributed to the enhanced formation of particle aggregates. However, the understanding of aggregation mechanisms remains rather limited. Recently, an enhanced particle aggregation was observed by the formation of small air bubbles resulting from high intensity agitations (HIA). In this study, a novel visualization system is designed and constructed for characterizing the fine bubbles formed in an HIA cell. The new design allows determination of gas evolution and bubble size distribution. With this system, the effect of dissolved air on fine bubble generation by HIA is investigated. The results show that HIA creates a favorable environment for the formation of gas nuclei and small size bubbles due to hydrodynamic cavitation.INTRODUCTIONFlotation is a dominant separation technique employed by mineral industry to recover the valuable mineral particles. However, in general, particles finer than approximately 10 µm are not effectively recovered by conventional froth flotation technique due to their low inertia and high specific surface area (Fuerstenau, 1988). Therefore, the fine particle flotation has been considered as the central challenge of flotation research. Substantial advances have been made for fine particle flotation from both a theoretical and technological point of view (Fuerstenau et al., 1979; Song and Lu, 1990; Subrahmanyam and Forssberg, 1990; Sivamohan, 1990; Sedat and Barry, 1991; Matis, 1995). High intensity agitation (HIA), for example, has found some success to improve fine particle flotation kinetics in laboratory tests (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998; Rubio and De Brum, 1994).The effect of mechanical agitation on flotation kinetics has been recognized for many years. In mid-1970s, Warren (1975) reported that increasing the shear rate of the pulp could improve the efficiency of ultra fine particle flotation. He attributed this improvement in flotation to the formation of aggregates. This concept of aggregation has been extended by Rubio (1978), and Bulatovic and Salter (1989), who employed high intensity agitation (HIA) method to promote aggregation. They found that HIA with the addition of collectors, frothers and suitable modifiers significantly improved both the flotation recovery and selectivity of ultra fine sulphide minerals. The improvement was explained by warren’s shear flocculation theory. Till now, many studies (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998) have been undertaken to improve fine particle flotation by HIA. However, most of these studies were focused on the relation between energy input and flotation efficiency. Less information was available for describing how the aggregate formed during HIA process."

Jan 1, 2006

By R. Siy, O. Neiman, B. Hilscher

"A full-scale prototype of “Jameson Downcomer” technology has been installed and tested on a Tailings Oil Recovery (TOR) vessel in Syncrude’s Mildred Lake extraction plant. Jameson Downcomers are a type of mineral flotation equipment used in the coal industry that Syncrude has extended to the recovery of secondary bitumen in the oil sand extraction process. The TOR vessels are currently being operated as single-gravity separation vessels, in series with the Primary Separation Vessels (PSV’s). We have developed a model to differentiate between “floating” and “non-floating” bitumen in the PSV’s, and then applied it to verify that the current TOR performance only captures the “floating” bitumen by simple separation. The existence of “non-floating” bitumen provides an opportunity for recovery enhancement by means of the Jameson Downcomers. To achieve bitumen recovery enhancement, middlings slurry is withdrawn from the TOR vessel, and passed through a number of parallel Jameson downcomers, within which the slurry is accelerated to a high-velocity free jet, and impinged upon the slurry surface inside the downcomer, in the presence of air. The aerated slurry is returned to the middlings zone inside the TOR, resulting in an incremental recovery improvement of bitumen in the TOR. The operation of the downcomers is thought to produce suitably small air bubbles for the flotation of bitumen, either by fluid shearing during the slurry jet impingement, and/or by micro-bubble nucleation. This full-scale prototype design has met or exceeded the recovery expectations of the original Research piloting, recovering at least 40% of the non-floating bitumen. In Syncrude Extraction, this provides high business value by a separation efficiency gain achieved with modest expenditure. As well, the system has demonstrated excellent operability and maintainability.INTRODUCTION Syncrude Overview Syncrude Canada Ltd. is one of the largest producers of crude oil from oil sands. Our crude oil production facility has the capacity to produce over 15% of Canada's total oil requirements. To do this, we surface mine oil sand, extract the raw oil known as bitumen from the sand using water-based processes, and upgrade that bitumen into sweet light crude oil by fluid coking, hydro processing, hydro treating and reblending. Our final product, Syncrude Crude Oil (SCO), is sent by pipeline to three Edmonton area refineries and to pipeline terminals which ship it to other refineries in Canada and the United States. The Syncrude operation is comprised of four major technology areas: Mining, Extraction, Upgrading and Utilities. As well, Syncrude invests more than $40 million annually in science and technology, and is among the top 50 companies in Canada for Research and Development (R&D) investment. Syncrude holds 21 active Canadian and U.S. patents."

Jan 1, 2012

By I. R. Muirhead, S. Frimpong

"The mechanization of mining operations in underground coal mines has led to faster cutting rates of coalfaces with increased levels of emission of gaseous and particulate contaminants in the workings. Consequently, the fresh air streams from the main ventilation systems reaching distant workings are often insufficient, ineffective or inadequate and have to be supplemented by auxiliary ventilation systems to create and maintain the required working environments underground. The efficiencies of auxiliary ventilation systems are largely affected by drivers of the system such as the type and capacity of the fan; the type, length, diameter and condition of the ventilation ducting and the distance from the discharge end of the intake ducting to the face. Traditionally, single point measurements of methane gas concentrations using either flame safety lamps or hand-held measuring instruments have been used to assess how safe underground coal workings were. Unfortunately, such occasional measurements of methane gas concentrations do not give an accurate picture of the real gas concentration in the working as they are often taken from the easily accessible locations in working. Continuous monitoring of the methane gas concentration in development headings enables a better assessment of the environmental conditions prevailing there. All variations in the methane concentrations are more easily captured on a continuous monitoring basis than by instantaneous single point measurements. The approach adopted in this work was to continuously monitor the concentration of methane very close to the face and about 60 m outbye in development headings, observe the types of auxiliary ventilation equipment and their sizes being used in the working as well as noting the lengths from the discharge ends of the forcing and exhaust ductings to the face.In this paper, empirical methods are used to calculate the mean efficiencies of the auxiliary ventilation systems in selected development headings in coal mines in North America. This enables the assessment of the effectiveness of the auxiliary ventilation systems and the identification of the system drivers in them. The results show that the efficiencies of the forcing systems ranged from 17.02% to 96.81% while the efficiencies of the overall systems varied from 6.04% to 54.16%. The distance from the discharge end of the intake ducting to the face appeared to be the strongest driver in the performance of the auxiliary ventilation systems studied. It was also noted that when the discharge end of the intake ducting to the face does not exceed 7 m, there were faster purging rates of methane at the face and the efficiencies of the overall auxiliary ventilation system were greater than 50%. These findings are very important in underground coal mining in North America as they will assist to avert calamities, such as the Westray coal mine disaster in 1992 which resulted from the explosion of methane gas, by identifying which components of the ventilation system need special attention to create safe working conditions underground."

Jan 1, 2003

By R. Grimard, M. Gamache, L. -P. Bigras, P. Cohen

This paper describes a real-time fleet management system for an undergroun mine. Dispatching, routing and scheduling are handled simultaneously, taking into account the mine status, operational constraints and vehicle location information. Each assignment decision takes into account the traffic on the road segments of the mine network, whether road segments are bi-directional or uni-directional, and ensures that each LHD (load-haul-dump) vehicle arrives at loading and dumping points with the correct orientation. Such a system can be used either as a simulation tool for strategic planning or as a real-time managing and optimizing system for operations. In the simulation mode, the system can accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. When used for real-time dispatching, routing and scheduling of vehicles, the system can optimize production with respect to various assignment criteria such as cycle-time minimization or deviation from a target production plan.

Jan 1, 2004

By J. C. Johnson

Underhand mining with cemented mill tailings for backfill has proven to be a safe and effective alternative to conventional overhand mining for rockburst prone mines. The ability of the cemented sandfill to survive a rockburst shock wave without failing has been observed at mines in the Coeur d?Alene Mining District many times in the last twenty years. To better understand the dynamic loading of this commonly used support material the National Institute for Occupational Safety and Health (NIOSH) performed laboratory experiments using a split Hopkinson Pressure Bar (SHPB) to quantify the maximum stress and energy absorption of cemented mill tailings from the Galena mine. Cylindrically shaped cemented backfill specimens aged 28 days were placed in the split Hopkinson pressure bar testing apparatus and a dynamic load was applied. The measured peak dynamic compressive strength of the cemented sandfill was 10.6 MPa (1540 psi) and is approximately twice the static unconfined compressive strength (UCS) of 5.5 MPa (800 psi). These test data showed about 95% of the initial energy was reflected away from the backfill and only 5% of the energy was absorbed. This may help to explain why backfilled stopes could withstand seismic events up to 3.5 Richter magnitude (Ml). When a compressive rockburst wave impacts a stope a large amount of the stress and energy is reflected away. The reflected wave is a tensile wave which creates tensile cracks and spalling in the entire wall of the stope. The backfill supports the damaged wall rock and holds it in place. Some of the stress and energy of the rockburst is transmitted into the backfill and because the backfill is being dynamically loaded it has a strength that is twice its static value and absorbs a substantial amount of rockburst energy. Although mining in deep underground mines is an extremely hazardous occupation, the use of underhand mining with cemented backfill for static and dynamic ground control increases the safety of the workers.

May 1, 2007

By H. M. Thurgood, F. A. Godfrey, F. W. Gilbert

This is a detailed presentation of the ancillary facilities, including power production, water supply, shiploading facilities, fire-fighting equipment, housing and community services. Additional subjects discussed include construction problems, townsite philosophy and staff organization.

Jan 1, 1968

By Adil Aledresse, Louis Mercier, Laxman Amaratunga

"The development of high capacity adsorbents with uniform porosity denoted, MP-HMS (Mercaptopropyl – Hexagonal Mesoporous Structure) using nanotechnology, and their ability to extract gold from solution, is presented. The preparation of highly effective heavy metal ion adsorbents by the incorporation of thiol moieties into the pore channels of mesoporous silica molecular sieves has been the subject of many nanotechnology research investigations. The unique feature of these nanoporous adsorbents is their ability to adsorb gold ions from ultra-low concentration solutions like mine effluent as well as from leached solutions in gold mills. The preliminary studies from laboratory simulated gold solutions show that the adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 370 mg gold per one gram of the nanomaterials from Tetrachloroaurate solution (up to 37% of their weight). Experimental studies indicated that the maximum adsorption of gold (as high as 99.9% recovery). The current studies will be extended to investigate the interaction of ionic gold complexes with nanomaterials. Future development of this work may lead to either to replace the conventional CIP/CIL processes or use nanomaterials in tandem with the former, suggesting plausible use of mesoporous material in pulp, MIP or in leach, MIL, as a novel gold extraction process.INTRODUCTIONGold typically occurs at very low concentrations in ores less than 10 g/t or 0.001% (mass basis). At these concentrations the use of aqueous chemical (hydrometallurgical) extraction processes is the only economically viable method of extracting the gold from the ore. Typical hydrometallurgical gold recovery involves a leaching step followed by the separation of the gold bearing solution from the residues, or adsorption of the gold onto activated carbon adsorbent. After elution from the activated carbon the gold is further concentrated by precipitation or electrodeposition."

Jan 1, 2008

By C. J. Brown

Controlling the level of impurities in copper refinery electrolytes is essential to achieving acceptable cathode purity. Purge of electrolyte is not an entirely satisfactory solution since the cost of neutralization, waste disposal, and replacement acid can be appreciable. The APU® process utilizes ion exchange resin to sorb sulphuric acid while rejecting metal salt impurities. Extensively employed for recovery of waste pickling and anodizing acids since 1977, the system is now being used at several refineries for removal of contaminants such as antimony, bismuth, iron, and nickel. The purified acid, which is recovered from the resin by water elution, is recycled back to the refinery tank-house, while the metals are typically recovered from the de-acidified by-product solution by precipitation.

Jan 1, 2005

By M. Vallée

"Geological and technical problems are often considered the most important ones affecting new mining projects. Typical problems and likely causes are reviewed based on current Quality Management and Continuous Improvement (QMCI) perspectives, giving particular attention to the work of W.E. Deming. As the “system approach” is an essential part of these policies, its characteristics are described with particular attention given to cultural- behavioural, organizational and systembased constraints described by J. Gharajedaghi. Given that poor communication and interaction among geologists, mineral processors and mining engineers/operators can seriously affect the adequacy of tests, project planning and execution, and mine profitability, these interrelated processes within the mining systems are analyzed and modelled. The impacts on models and simulations of ignoring typical data, information and knowledge uncertainties are addressed. Adapting W.E. Deming’s Fourteen Points, System of Profound Knowledge and insistence on leadership, and the analysis of mining system constraints, will allow the effective QMCI approach required to reduce geological and technical risks. Whenever we achieve this goal, we will be in a better position to overcome environment-, market-, finance- and community-related problems, achieve higher company and industry profitability as well as more sustained development. RÉSUMÉLes problèmes géologiques et techniques sont souvent considérés les plus importants parmi ceux qui affectent les nouveaux projets miniers. Des problèmes typiques et leur causes sont étudiés dans la perspective de gestion de la qualité et d’amélioration continue (GQAC), en relation avec les travaux de W.E. Deming. Comme l’approche système est au centre de ces méthodes, ses caractéristiques sont décrites en donnant une attention particulière aux contraintes de types culturel-comportemental, organisationnel, et systémique décrites par J. Gharajedaghi. Compte-tenu que les lacunes dans les communications et les interactions entre géologues, minéralurgistes, et ingénieurs/opérateurs miniers peuvent affecter sérieusement la validité des essais, de la planification et de l’exécution des projets ainsi que la rentabilité des exploitations, ces processus connexes font l’objet d’analyse et de modélisation. Les impacts sur les modèles et les simulations de l’incertitude des données, informations et connaissances sont soulignés. En adaptant au système minier les Quatorze Obligations et le Système de connaissance approfondie de W.E. Deming ainsi que l’analyse des trois types de contraintes, nous pourrons développer une approche GQAC permettant de réduire les risques géologiques et techniques des projets miniers et des exploitations. Ceci nous pemettra de mieux faire face aux problèmes reliés à l’environnement, aux marchés, au financement et aux conditions sociales, d’améliorer la rentabilité des exploitations minières et de l’industrie, tout en contribuant de façon accrue au développement durable."

Jan 1, 2003

By Andrew R. Marchbank

The application of biologically assisted methods for metal extraction in the mining industry has a long history, but development of modern techniques has been relatively slow. There is, however, a resurgence of interest in the industry with the recent development of methods to successfully treat base metals concentrates. Two major pilot plant programs for treatment of chalcopyrite concentrates have been initiated in the past year and results from one are beginning to be released. This paper provides an overview of methods that have been applied in the past; from the earliest deliberate applications of the technology, through the copper and uranium heap and dump leach applications, the more highly engineered agitated tank leach gold applications and the developments currently taking place in the industry.

May 1, 2002

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

By André Laplante, Robert C. Dunne

"The role of flash flotation in precious metal recovery is reviewed. Interacting flash flotation and gravity recovery is discussed. The GRG test can be used, when linked to the behaviour of gold in grinding and classification units, to predict the recovery of GRG by flash flotation. The Cadia mill in New South Wales is used as a case study of circuit design, performance and simulation. It is shown that high throughput coarse grind applications such as Cadia require very effective fine GRG recovery systems in the primary grinding loop, which are more consistent with flash flotation than batch centrifuge concentrators (BCCs). BCCs can effectively recover a significant fraction of the GRG from flash concentrates, as predicted by laboratory testing and confirmed at a growing number of mill sites.INTRODUCTIONThe GRG test was designed to characterize Gravity Recoverable Gold (GRG) ten years ago (Woodcock and Laplante, 1993; Laplante et al, 2000), in response to the need to predict how much gold could be recovered from the main circulating load of grinding circuits using centrifuge concentration. The amount of GRG is not itself a prediction of gravity recovery: the performance of a gravity circuit nested in a circulating load also depends on the type and size of unit used, how much of the circulating load is treated, and how many times GRG is recycled and presented to the recovery circuit. The GRG test was first used in a simulator to predict gravity recovery (Laplante et al, 1995), and indeed most of the early tests targeted ores or prospective ores for which gravity recovery was an obvious match. As the test became more accepted, more and more samples returned a verdict that precluded the use of gravity recovery, or made it marginal. Typically, such ores are either copper-gold or base metal ores in which the GRG content is often fine (largely below 105 um) and ranges from 8 to 33%. Extensive simulation and plant sampling tests, either published (Laplante et al, 1997) or proprietary, show that full scale gravity recovery for these applications is generally below lo%, and can be as low as 2%. Not in all cases are such low recoveries economically unjustifiable, since there is documented evidence (Darnton et al, 1992) that a significant proportion of the gold recovered, at least in the case of base metal ores, would not have reported to the copper or zinc concentrate and received NSR credits."

Jan 1, 2002

By Gus Van Weert, Peter Kondos

"Ore sorting has been quite successful in providing a separation means in the rock size range of 1 to 6 inches; a range where mineral dressers do not have many options. The industrial minerals and recycling worlds have embraced this technology. However, ore sorting has not found wide application in the base or precious metals mining industry. One reason for this is thought to be the reliance of most sensors on rock surface characteristics, not very useful in case of sulphides, non-existing in case of gold. Microwave heating, however, is specific for sulphides and graphite (or carbonaceous matter) embedded in the rocks; washing or even drying does not appear necessary. Separation can be done afterwards by already existing ore sorting technology using infrared sensors. Test results on six Nevada gold ore samples are presented in detail. Some simple test procedures are also presented for those wishing to explore the microwave potential of sulphide sorting in their own operations.INTRODUCTIONMineral processing in the base metals industry most often involves upgrading of the ore, concentrating the valuable mineral fraction by classic methods, such as flotation. Since the liberation of minerals in the ore occurs mostly at or below the 100 micron level, the industry has been living with fault lines, so to speak, between blast hole spacing (10,000 mm), run-of-mine ore size (100 mm) and beneficiation size (0.1 – 0.01 mm). The acceptance of ore sorting will inevitably lead to the revisiting of the following questions: “Exactly how much below ore grade rock ends up in the mill because the geologists or the miners cannot define the resource boundaries more precisely? How can the economics of dilution be improved? How many ore grade rocks are lost with the overburden?”"

Jan 1, 2007

By W. Banda

"Trial application of air decks on a production shot improved fragmentation (32% reduction in x50). Empirical fragmentation models and digital image processing software were used to estimate fragment size distribution of the blasted muck pile. The x20, x50, and x80 passing fractions, and top size were 42, 265, 683, and 1,455 mm, respectively. Air-deck application reduced explosives load in blastholes, lowering total charging cost by US$20/hole (15% decrease) and the powder factor to an average of 0.86 kg/m3 (12% decrease). Blast results were 443,624 t of blasted material from the block (90% of total muck pile) was smaller than 900 mm.RÉSUMÉ L’application pilote de trous d’air dans le cadre du coup de mine effectué pour commencer la production a amélioré la fragmentation (une réduction de 32 % des x50). Des modèles empiriques de fragmentation et un logiciel de traitement numérique des images ont permis d’estimer la composition granulométrique des fragments du tas de déblais abattus. Les fractions de passé de crible de x20, x50, x80 et la dimension supérieure étaient représentées par des dimensions respectives de 42, 265, 683 et 1 455 mm. L’application de trous d’air a permis de diminuer la charge d’explosifs nécessaires dans les trous de mine, réduisant ainsi les coûts totaux de chargement de 20 $ US/trou (soit une réduction de 15 %) ainsi que le facteur de chargement (facteur poudre) à une moyenne de 0,86 kg/m3 (soit une réduction de 12 %). Les coups de mine ont résulté en 443 624 tonnes de matériaux abattus du bloc (soit 90 % du tas de remblais total) mesurant moins de 900 mm. INTRODUCTIONThe main objectives of production blasting are to achieve optimum rock fragmentation and to minimize overall production costs. Because blast fragmentation significantly affects the profitability of a mine, blasting is the first step of the size reduction in mining: An optimum size distribution is required to maximize the performance of mining and subsequent milling processes. If the fragmentation size distribution can be modelled and controlled, operations performance will improve. Blast fragmentation modelling is important in mineto- mill optimization: It allows the estimation of blast fragmentation distributions that can be modelled in downstream mining processes to determine the optimum blast design."

Jan 1, 2018

By R. Gallinger, B. Kelley

"In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale.The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP’s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed assufficient justification for the formation of INAP.INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage.This paper will explore the international efforts and activities of INAP."

Jan 1, 2005

By Gustav Nillson

There is a difference in design parameters between steel linings and rubber linings for grinding mills. The basic design parameters for rubber are described and a comparison is made between steel and rubber in different applications.

Jan 1, 1979

By F. M. Makarinsky

"SynopsisThe Kanichee open pit mine and milling complex is situated approximately four air miles north-west of Ternagami, Northern Ontario, in Strathy Township. Mining and milling production commenced in January 1974.Milling throughput currently is at a rated capacity of 500 tons per day, seven days per week. A bulk nickel-copper sulphide concentrate is produced, and is trucked daily to the smelter at Falconbridge Nickel Mines Limited, Falconbridge, Ontario, some 120 road miles from Kanichee. Concentrate grades produced are in the order of 4.0% Ni and 8.0% Cu, with corresponding recoveries of 68-70% nickel and 86-90% copper. Stage additions of 100% guar-gurn solution reagent to the flotation cells for depression of talcose minerals, proved to be the major break-through for optimizing metallurgical performance.2. HistoryThe present Kanichee Mining property is known to old-timers in the Temagami area as the former Cuniptau Mine. Several attempts were made in the mid '30's and 40's to extract the ore at a profit, but each effort resulted in failure.In 1933-36, Cuniptau Mines Development Co. Limited, later called Cuniptau Mines Limited, sank a 245-foot vertical shaft and completed 2,200 feet of lateral work on the 100-140 and the 225 foot levels. Fifteen tons of ore were sent for testwork to the Mines Branch, Ottawa, Ontario.Cuniptau Mines Limited, in 1936, milled some 3,000 tons, and the resulting concentrate was put through a pilot smelter situated on the present mine site. Metallurgically, the smelting results were not encouraging, primarily due to the high melting point of the talcose minerals in the concentrate. From the period 1937-48, minor exploration work was done by Ontario Mining Corporation, Ontario Nickel Mines Limited, and Trebor Mines Limited. During the period 1948-49, 128 diamond drill holes, totalling 40,900 feet were evaluated by Trebor Mines Limited. In 1961, the name was changed to Ajax Minerals Limited, during 1968, five diamond drill holes were sunk, totalling 1,700 feet. Since that period the property has remained idle."

Jan 1, 1975