Search Documents

By J. Bouchard, M. Levesque, D. Georges-Filteau, P. Radziszewski, G. LeBlanc

"Grinding mills are infamous for their extremely low energy efficiency. This paper reports the results of an investigation that characterized energy outputs in industrial grinding mill circuits. It identifies and discusses the potential for recovering energy from grinding circuits. Agnico-Eagle Goldex Division, Mine Canadian Malartic, and New Gold New Afton Mine participated in the study by providing operating data for three semi-autogenous grinding mills and four ball mills. Results showed that on average, 79% of the supplied electrical energy was converted to heat absorbed by the slurry, 8% was lost through the drive system, and approximately 2% was transmitted to the ambient air. Only 9% of the input energy was actually used for grinding. The remaining 91%—wasted as heat—could potentially be recovered using suitable technologies or integrated energy management systems. This topic remains to be further investigated. ¦ KEYWORDS Comminution processes, Energy recovery potential, Grinding mills RÉSUMÉ Les broyeurs sont tristement célèbres pour leur rendement énergétique médiocre. Cet article présente les résultats d’une étude qui caractérise les rendements énergétiques des circuits industriels de broyage et examine les possibilités de récupération d’énergie dans les circuits de broyage. La mine Goldex d’Agnico Eagle, Mine Canadian Malartic et la mine New Afton de New Gold ont participé à l’étude en fournissant des données de fonctionnement pour trois broyeurs semi-autogènes et quatre broyeurs à boulets. Les résultats montrent qu’en moyenne 79 % de l’énergie électrique fournie sont convertis en chaleur absorbée par la pulpe, 8 % sont perdus dans le système d’entraînement et environ 2 % sont dispersés dans l’air ambiant. Seuls 9 % de l’énergie primaire sont, de fait, utilisés pour le broyage ; les 91 % restants (perdus sous forme de chaleur) peuvent potentiellement être récupérés à l’aide de technologies adaptées ou intégrées dans des systèmes de gestion de l’énergie. Cette question demeure toutefois ouverte. ¦ MOTS CLÉS broyeurs, potentiel de récupération de l’énergie, procédés de comminution INTRODUCTION Grinding is largely recognized as a very inefficient process; energy efficiency estimates range from < 1 to 2% (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002, 2004) when comparing the input energy to that required for generating new mineral surfaces. Criticizing an “ill definition of the reference for the output energy,” Fuerstenau and Abouzeid (2002) proposed a “more meaningful baseline” would be “the energy for producing new surface area by the ¬mens.” Based on this reference, they concluded that “the ball mill is reasonably efficient energetically,” exhibiting an efficiency of approximately 15% for quartz."

Jan 1, 2019

By Esa Peuraniemi, Hanna-Leena Heikkilä

Boliden Harjavalta has been operating a copper flash smelter since 1949. Thus, in 2019, the smelter is celebrating its 70th anniversary of flash smelting. Slag formation is an integral part of the smelting process; currently the processing of slag is based on froth flotation at the slag concentrator. It provides high recovery of copper but restricts slag utilization; the final copper slag is deposited in a landfill. The Harjavalta smelter commissioned a new landfill area for final slag in May 2018. This paper describes the full project from permitting to commissioning of a new landfill area. The permitting process is described comprehensively, including environmental impact assessment together with the environmental and dam safety monitoring. During the environmental impact assessment, observations on rare animals protected on European level were made as well as archaeological findings. Successful completion of the permitting allowed the construction phase to start on time. After six years of intensive work, the new landfill was commissioned in May 2018. The new landfill area provides a sustainable way to store the smelter’s slag for decades to come. INTRODUCTION Slag processing Sulphide based concentrates have always formed the main raw material stream at Harjavalta’s copper smelter. During the smelting and converting steps, the iron included in the concentrate is oxidized and fluxed using a silica-based sand. Originally, the slag was processed by using an electric slag cleaning furnace after which the final slag was water granulated. Froth flotation has been utilized for slag treatment since 1966. In the beginning, the slag was cooled in open ditches. In 1984, controlled slow cooling of slag was licenced to enhance copper recovery at the flotation plant. Today, the slag from both the smelting and converting is tapped/skimmed to slag ladles and treated in the following steps: Slag ladle transportation from the smelter to the cooling area by slag hauler Slow cooling of slag in the ladle to allow mineral precipitation Unloading the slag by tilting the ladle; causing the slag to crush as it drops from the ladle Feeding the crushed slag (-500 mm) by wheel loader to a slag concentrator’s feed funnel followed by a conveyor belt transporting the slag to the concentrator plant Crushing and grinding using lump and pebble mills Froth flotation of the valuables Recycling the slag concentrate back to the smelter feed after dewatering Pumping the final copper slag to the landfill area.

Jan 1, 2019

By M. K. Kim

This study presents a framework for quality inspection of precast concrete components using the 3D laser scanning technique. As precast concrete-based rapid bridge construction is getting standardized, quality assessment of the precast concrete becomes critical for preventing any failures during the construction process. Moreover, as Building Information Modeling (BIM) gains popularity in the construction industry, autonomous and intelligent inspection systems are needed. Current method for quality control of precast concrete components, however, heavily relies on visual inspection and contacttype measurements, which are time and labor demanding. Also, storage and delivery systems of inspection information such as the procedures and results of quality inspection are lacking. To overcome these limitations of the current quality assessment technique for precast concrete, this study aims to develop a BIM-based framework for efficient quality inspection of precast concrete with the use of a 3D laser scanner. First, we formulate practical guidelines including detailed inspection procedure, selection of optimized scanner and scan location, inspection criteria, and data storage and delivery system. Second, to investigate the applicability of 3D laser scanning to precast concrete quality inspection based on the proposed framework, a case study inspecting quality of a lab-scale object assumed as precast concrete component is presented for detecting defects.

Aug 1, 2013

By G. Stokreef, B. R. Davis, M. Kadiyski, T. LeBel, Alvear Montenegro, R. Parra, V. Montenegro

A drop tower and methodology were developed to study the impact of mineralogy on the flash combustion behaviour of copper concentrates. Reaction shaft conditions of a flash furnace were simulated using a drop tower reactor and different molar ratios of oxygen gas to sulphur in the feed. Five feeds were tested in the drop tower including pure minerals chalcopyrite and pyrite as well as two mineralogically distinct copper concentrates and a blend of the two. The behaviour of each of these five feeds were evaluated through analysis of the solid combustion products for elemental sulphur, mineralogy and particle size. Desulphurization curves for each of the feeds were produced. It is thought that the desulphurization behaviour of pure minerals can be used to estimate the behaviour of a concentrate and that a blending recipe could be developed, which can optimize the chemical and mineralogical inputs to the flash furnace and guide operations on the optimum furnace conditions. Overall, the drop tower has proven to be a useful tool for studying flash combustion processes. Experimental results suggest that mineralogy has a significant impact on the conditions required for the production of matte with consistent grade. This finding is especially significant for custom smelters, which may see several different blends in a day. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process that is used to produce copper matte from copper sulphide concentrates. Dried concentrate(s), silica flux, and secondary materials are blended to a target chemical composition, typically given by the Cu/S ratio, before processing. This fine, dried feed is dispersed throughout the heated furnace reaction shaft with an O2-enriched reaction gas. The particles heat up in the shaft of the furnace, ignite and undergo reactions that pre-oxidize the iron sulphide and some of the impurities in the feed. Oxidation reactions in the shaft of the furnace desulphurize the feed and produce an SO2-containing off gas. The reacted particles fall into the furnace settler and separate into a Cu-rich matte and an iron-silicate slag, while the SO2-containing off gas is carried out of the furnace for heat and dust recovery, as well as H2SO4 production. Some concerns during operation of the furnace are dusting, over or under oxidation of the feed, and a stable flame.

Jan 1, 2019

By Franco Chiesa, David Levasseur, Bernard Duchesne

A 500kg aluminium AlSi7Mg03 casting has been poured and the metallurgical quality at different locations inside the casting has been thoroughly investigated. It included measuring the local tensile properties (YS, UTS, El) in the T6 condition, the dendrite fineness (DAS) and the level of microporosity. A correlation was found between the microporosity level, the local solidification time and solidus front velocity; this correlation allows to predict the porosity level in large aluminium castings (solidification times between 20 and 200 minutes). Quite expectedly, properties varied widely within the casting and the actual mechanical properties were much less than the "textbook values" based on measurements carried out on separately cast standard specimens. A correlation between the secondary dendrite arm spacing (DAS) and the local solidification time was in keeping with previously published data. Finally the conditions to obtain an acceptable finish on machined surface were determined.

Jan 1, 2014

By Ron Tessier, Claude Bazin, Robert Grant, Mike Cooper

"Grinding simulators are now widely available to assist in the optimization of industrial circuits. They provide circuit operating conditions or flowsheet designs that yield a given product size distribution. However, they do not provide information of the impact of a change of product size distribution on the subsequent flotation or leaching stages. This paper presents a method to predict grade and recovery indices for a flotation plant as a function of the flotation feed size distribution. The application of the method to various size distributions allows the determination of the optimal fineness of grind. A case study for a CuPb rougher circuit of a New Brunswick complex sulphide processing plant is presented to illustrate the method.IntroductionIs the grinding circuit product fineness optimum for the subsequent separation steps? This is a question that is certainly very difficult, but critical, to answer. Laboratory and pilot plant testworks can provide clues as to whether grind should be finer or coarser. For a full scale operation there is no other way than trying to change the setup of the grinding circuit and verify the effect on flotation. True effects can, however, be masked by the numerous and unexpected disturbances inherent to grinding and flotation circuit operations. A good preliminary investigation requires a noise free environment to elaborate possible solutions for the question.Plant simulators provide this noise free environment. However, despite grinding and flotation simulators having evolved significantly for the last 20 years, very little is available on the integration of both simulators to analyze the effect of fineness of grind on metallurgical performances. For instance, a grinding circuit simulator may help to find the tuning of a grinding circuit that will yield the desired fineness of grind, but does not inform on the effect the new product size distribution will have on the separation stages. Linking grinding and flotation would require a flotation plant simulator with the rate and infinite recovery parameters for each mineral in each size interval considered. This approach is seldom used because of the tedious work required to estimate the model parameters. Recently Leroux(1992) proposed a method to predict mineral liberation from grinding ore of known mineralogical texture. Although the method is still at its infancy it may provide, when combined with a reagent conditioning model (e.g Niemi et al., 1982; Bazin et al., 1988), a way to simulate flotation without the need of entering the numerous parameters of a flotation model."

Jan 1, 1994

By D. T. Aikens, R. Gaudreault

"This paper summarizes structural repairs carried out on a marine wharf consisting of six 13.7 m by 13.7 m reinforced concrete cribs linked together by five 14.6 m long beam spans. As a result of problems during original construction and twenty years exposure to severe weather conditions, the deck support system between the cribs required major restoration work. In particular, some of the beam seats under the crane rail supports had marginal bearing area to support the structural loads. Faced with closure order for the wharf which is required to bring in raw materials to the plant and a long outage to make repairs as stipulated by Ports Canada (owners of the structure) alternate means of making the required repair were examined.The method chosen allowed the work to be done much more quickly, at lower cost, without taking the wharf completely out of service. The badly deteriorated seats were rebuilt using epoxy grout, tapered sole plates and a positioning jig."

Jan 1, 1988

By Ron Bradburn, Derek Perkins

"The Brenda mine is located in south central British Columbia, 22 km north west of Peachland, in the heart of the Okanagan Valley. Situated at an elevation of 1500 metres, the mine area straddles the divide between the headwaters of Trepanier Creek and Peachland Creek. These flow into Okanagan Lake, the chief valley water resource located 1100 metres below. The creeks are of great significance to the water management of the area as they constitute the water supply for the Municipality of Peachland, a thriving retirement community with a population of 5000. A location map is shown in Figure 1.The history of the Brenda Mine operation has been well documented previously. After twenty years of operation, the open pit mine shut down in June 1990 due to the depletion of its ore reserves. During the course of its life, it produced 109 million tonnes of waste rock which is thought to contain approximately 0.10% copper as chalcopyrite and 0.015% molybdenum as molybdenite stored in four rock piles around the pit. Similarly, approximately 200 million tonnes of tailings were produced grading 0.015% copper and 0.005% molybdenum. During operation, tailings were hydrocycloned to produce a coarse sand for dam building with the fine slime stored behind the dam. It is estimated that 40% of the tailings were used for the dam construction. The layout of the mine site is shown in Figure 2.The mine was operated under a zero discharge permit. This was achieved by diverting practically all surface water flowing towards the mine area around the site. Water affected by mine operations, was discharged to the tailings impoundment, and recycled to the mill for reuse. The recycle rate was 90% and seepage from the tailings embankment and saddle dam was pumped back to the tailings pond. Because acid drainage was not a problem with the low grade Brenda rock, runoff from the rockpiles was initially released to the local environment. However, due to the alkaline nature of the waste rock, dissolution of low concentrations of molybdenum in the site runoff waters became evident by the late 1970's. The molybdenum content of Peachland Lake, the water reservoir for the municipality of Peachland, approached the Canadian Drinking Water Standard of 0.25 ppm. By 1979, a series of diversion and collection ditches was completed to direct all runoff water from the rockpiles to the tailings impoundment area. This had a significant detrimental effect on the site water balance causing it to go into a considerable surplus condition. During normal operation, this oversupply was contained by the rate of tailings dam building. An economic shutdown of the mine during 1984 forced a limited discharge from the site to protect the integrity of the tailings dam."

Jan 1, 1995

By J. Roth

"While not taking issue with the general thesis expressed in Dr. Ridge&apos;s analysis of the role of genetic concepts versus observational data in ore exploration (Ridge, 1983), the criticism could be offered that the author tends to slight the importance of conceptual (i.e. theoretical) models in mineral exploration.As a general rule, observational data in science lacks significance and utility without a theoretical construct to organize those observations. Theory in turn dictates what observations are made-and which ones are judged important. Thus, for example, prior to the elaboration-and acceptance- of the current model for volcanogenic base metal deposits, the structural aspect s of these deposits were most closely observed and studied by explorationists. The nature of the enclosing rocks and any attendant alteration was given minimal attention, and certainly didn&apos;t figure prominently as an exploration guide.Similarly, the importance of alteration features to exploration for porphyry copper-molybdenum deposits was only perceived when a theoretical model was developed to account for these aspects. Indeed, many of these porphyry copper deposits were regarded as epigenetic vein deposits by geologists of an earlier era observing and examining on a different physical scale-and with a different theoretical bias.In constructing and evaluating such conceptual models, explorationists primarily rely on observation data and proximate associations; speculative thoughts as to ultimate provenance or crustal evolution clearly play a subordinate role, as Dr. Ridge argues. This, however, should not obscure the fact that concepts and theories do indeed exert a major influence in mineral exploration."

Jan 1, 1983

By Laxman M. Amaratunga, David N. Yaschyshyn

"In the mining industry several types of fills are used for backfill operations. They are broadly categorized into three basic types: rock fill, hydraulic/slurry fill, and paste fill. Recently, paste fill has become the popular alternative for backfilling because of its many environmental and operational advantages including its ability to use total tailings, both fine and coarse fractions.Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings, which are otherwise excluded from backfilling, for utilization in backfill as a readily available supplementary fill material. Previous experimental work investigated the use of agglomerated fine gold mill tailings in low density slurry fills (60 -70% pulp density), consisting of varying agglomerate and tailings compositions.This paper presents the ongoing research into utilizing these agglomerates in a high density paste fill (70 -85% pulp density). Various binder dosages, curing period and combinations of pellet to tailings ratios were studied. Slump of the raw fill and compressive strength of the cured fill were examined. Results from the above study indicate that agglomerated tailings paste fill (ATPF) has superior strength characteristics when compared to total tailings paste fills.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. These tailings consist of a coarse fraction and a fine fraction and can be either reactive (acid generating) or non-reactive. Most mining operations utilize the coarse fraction for backfilling while the fines have been traditionally disposed of in surface tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10 - 30% w/w of >45 µ,m) in the fill. This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused portion of fine tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMD) seepage from these ponds has proven to be a costly environmental problem and long term liabilty.One practical method to reduce the environmental impacts associated with the tailings pond and to modify the physical and chemical properties of the fine mill tailings so that they can be utilized and disposed of in an environmentally safe manner through surface or underground applications is through agglomeration using the Cold-Bond Tailings Agglomeration technology (CBTA). Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings for use as coarse aggregates for underground backfill, gravel or surface covering material. CBT A reduces the necessity of impounding tailings on surface while providing a suitable coarse aggregate resource material for practical use. Although the CBT A technology has been mainly limited to pelletization agglomeration alone, other forms of agglomeration like pressure agglomeration which include the techniques of briquetting and extrusion have also proven successful (Amaratunga, 1995)."

Jan 1, 1996

By F. King, R. Sutherby, J. Been

With thousands of kilometers of buried oil and gas pipelines throughout the country, carrying flammable, high-energy hydrocarbons, the integrity and safety of this transportation and distribution network are paramount. The pipeline industry has the primary responsibility for pipeline safety and has in many ways taken the lead in dealing with safety issues. Over recent years, regulatory demands have increased, requiring operators to comprehensively evaluate their pipelines through indirect and direct inspections and to manage risk through integrity programs. Mechanistic and correlative models have been developed that assist in the prediction of pipeline integrity and the determination of reassessment intervals. These lifetime prediction models are based on decades of laboratory research as well as pipeline operating data, material data, and field monitoring data pertaining to soil conditions and CP. An overview is presented of an integrated approach towards the development of such models for the evaluation of external cracking and corrosion of transmission lines.

Jan 1, 2005

By Jan E. Nesset, L. Paul Staples

"High Gradient Magnetic Separation (HGMS) technology, although developed over 2 decades ago, has not been widely applied to the separation of sulphide minerals. Under conditions of strong magnetic field gradients, weakly magnetic minerals such as chalcopyrite (CuFeS2) and marmatite (Zn(Fe)S, sphalerite with iron in solid solution) behave paramagnetically and can be effectively separated from diamagnetic minerals such as galena (PbS). The application of this technology to the separation of Cu-Pb and Zn-Pb bearing streams in the treatment of fine grained complex sulphides may in some cases be more effective than separation by flotation. A 2 TPH Sala HGMS pilot plant was operated at Brunswick for a nine month period, ending in March 1995. The testing demonstrated the mechanical reliability of the technology, the consistency of operating results and the scale up from laboratory testing. HGMS is seen as a complimentary technology to flotation, best suited to performing those separations of galena (and other diamagnetics) which flotation does not do as well.IntroductionBackgroundSince the turn of the century, the magnetic character or magnetic susceptibilities of minerals have been determined with increasing precision and accuracy. Figure 1 illustrates specific magnetic susceptibilities of some common minerals. As long as susceptibility ranges do not overlap, separation is possible.In 1937, the principle of using a magnetizable matrix material in a magnetic field to increase both magnetic flux density gradients and number of capture sites for susceptible minerals was first applied (Frantz). It was not until the 1970's, however, that the genuine development of wet high gradient magnetic separation began with the introduction of very fine matrix materials to the magnetized volume of large solenoid magnets. Today, dozens of HGMS units purify, filter and separate minerals, primarily for the removal of iron stained minerals from clays used in the paper coating and china clay industries and for the recovery of fine titanium and iron oxides in the iron ore industry. Only the Garpenburg mill in Sweden is currently applying a continuous HGMS machine to separate complex sulphide minerals; upgrading a lead concentrate since 1988."

Jan 1, 1996

By Gordon Thompson

"Development of the unique Mine Games exhibition at Science World British Columbia is the largest ever collaboration of many interests to present the story of mining and the issues of mineral development delivered to the public by a science education centre.IntroductionMineral education programs have long been a major focus of the British Columbia mining community. Mine Games and its tremendous potential to enhance industries image and the public&apos;s awareness of mining is unequalled in the field of Issue Based Education Exhibits.The main goal of the exhibition is to look at the future of resource industries in a rapidly changing world of economic activities, new technologies, and growing public concern for the environment. Three challenges were the aim of the exhibition: to increase participation, to serve as a tool to increase interest in science and technology, and to draw an increasing number of school students to the interests of geology and the earth sciences. Mine Games is to serve as a meeting place for discussion of issues and where reliable information can be shared and new ideas explored.The exhibition is designed to develop new approaches to hands on learning that encourages visitors to explore and generate discussion and thinking with respect to resource development activities.The role of author, beginning in 1993, was, with senior industry leaders, to coordinate the raising of $1.3 million to complete the funding of the $1.6 million project total. The second and most interesting challenge was to work with the many minds that were collaborating to create the exhibition and to assure that the facts and science were correct. This involved the coordination of ""expert groups"" that verified the science and technology and the issues that the creative design team at Science World planned to use in development of each exhibit module."

Jan 1, 1995

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-ehalcopyrite core interlayered pyrite-sphalerite-galena (pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyritequartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone I) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (II and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone I, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F, fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By So-Yeong Lee, Moosang Lee, Seung Hwan Ahn, Ho-Sang Sohn, Jongshin Chang

It is necessary to understand the characteristics, phase changes and chemical reactions of flue dusts introduced from a furnace to an off-gas line in order to achieve the stable operation and the improvement. This study is to develop the dust reaction model for chemical reactions of dusts in an uptake shaft of smelting furnace and a waste heat boiler. Phase equilibria and reaction paths in this system were determined by thermodynamic calculation with experimental and industrial data. The oxidation reaction rate of dusts was determined by the gas film mass transfer controlling. And the sulfation reaction rate was evaluated by the unreacted shrinking core model. Kinetic parameters were estimated by reference data including industrial ones. The present study with the developed model shows various effects of temperatures, dust particle sizes, and O2 gas partial pressures on dust reactions. INTRODUCTION The flue dusts from a copper smelting furnace move along a furnace off-gas stream into an uptake shaft and a waste heat boiler (WHB) and electrostatic precipitator(s). It is necessary to control the dust quality in order to stabilize the operation because the sticking behaviors differ depending on the phase of dusts. Phase changes of dusts are caused by chemical reactions at given conditions such as temperature and partial pressure of gases. Therefore, it is required to understand the phase changes and chemical reactions of dusts in order to perform the improvement and stable operation. The present study carried out the investigation to understand their fundamental knowledge. Especially, this study was focused on the kinetics of chemical reactions of flue dusts, developed the model. In particular, the scope of development and utilization of the model was defined as the uptake shaft of the Mitsubishi S furnace and the S-WHB radiation section in the Onsan smelter. Information needed for the modeling work referred to data from these processes.

Jan 1, 2019

By Esau Arinaitwe

The most extensively used methods and approaches for characterizing and selecting frothers for plant application are based on measurements in clean water in the absence of solids and without consideration of physicochemical factors that are known to influence the properties and behavior of practical flotation froths, and hence metallurgical performance. These factors include aquatic chemistry, collectors, modifiers, particle shape and size, and pH. Understanding interactions between these factors and the role and relevance that they play in characterizing frothers and froth zone properties will greatly aid in the frother selection and evaluation process. Such an understanding will also greatly enhance the ability to create frother solutions that are sufficiently robust to plant variability (such as mineralogical, comminution, operational, physical and chemical). This paper reports results of a “systems approach” study designed to probe ways in which physicochemical factors a) influence frothing and bubble size in 2- and 3-phase systems, and b) confound correlation of fundamental measurements with flotation outcome. The concepts and insights gleaned from fundamental frother studies, together with empirical laboratory flotation tests and a thorough understanding of plant needs and challenges were used to develop and implement customized frother formulation at a Cu-Mo flotation plant. Plant metallurgical data and qualitative assessment of froth zone properties showed that a frother formulation developed using the approach described here provided marked improvements in froth characteristics (mineralization, mobility, stability, persistence). These improvements resulted in better circuit control and significant performance advantages, such as improved coarse particle recovery, without detrimental downstream effects. INTRODUCTION Successful recovery of value minerals of sufficient grade via the flotation process requires selective manipulation of the value minerals to render them hydrophobic using collectors and modifiers. The hydrophobized minerals then attach to air bubbles and the mineral-bubble aggregates are selectively transported through the froth zone into the launder. Frothers play a critical role in froth formation and more importantly in achieving and maintaining desirable froth characteristics (for example, stability, mobility, persistence) that are essential in facilitating the selective transport and recovery of value minerals. Fundamentally, frothers contribute to the transient stability of thin liquid films and so aid in reducing bubble coalescence rates in the pulp and froth zones, thus maintaining the small bubbles required for efficient bubble-particle attachment. Invariably, the action of frothers at the liquid/gas interface in the pulp and froth zones impacts bubble stability, water and solids transport to the froth, which in turn impacts froth mobility, froth carrying capacity, and the concentrate grade. Consequently, selection and evaluation of frothers for flotation plants requires careful consideration of the frother type, though the choice is limited to only two main classes of compounds in terms of fundamental chemistry (short chain alcohols and polyglycols). Even with the selection of what is thought to be the best frother for a given application, practical knowledge of the froth zone and experience in controlling its properties is essential for maximizing metallurgical performance.

Jan 1, 2019

By S. Bantubani, I. Mc Dougall, S. Arjun, H. Joubert, R. Hansraj

The requirements determining the design of the Söderberg electrode columns used in base metal applications are different to those of other industries. There is a strong trend to position the contact shoes above the furnace roof in order to reduce the risk of water leakages directly onto the furnace bath. Tenova Pyromet has adapted its proven electrode column design for application on base metal electric furnaces based on these requirements. The design modifications implemented as well as considerations regarding the overall electrode-roof-furnace arrangement are discussed. Equally important is the management of the Söderberg electrodes to prevent over or under baking. Tenova Pyromet has developed the AutoFurn™ furnace controller to not only optimise furnace operations, but to improve electrode management. An overview of the electrode management control philosophy implemented by AutoFurn™ is provided, focusing on intelligent electrode regulation, slipping and baking. INTRODUCTION Tenova Pyromet has developed an electrode system for use in base metal furnaces, which builds on the experience that Tenova has gained during the past 30 years with electrodes in the ferroalloy and base metals industries. In base metals applications, an important safety consideration is the minimization of water within the furnace and on the furnace roof. In addition, direct contact between copper equipment such as contact shoes and pressure rings and the contents of the furnace is discouraged. In a 3 phase AC furnace, three electrode columns transfer the electrical energy to the furnace bath. Both Söderberg and prebaked carbon or UHP graphite electrodes are in use in base metal furnaces. In each column, the electrode is held in position by a hydraulic slipping and regulating device, a pressure ring and contact shoes. The electrodes can operate in a submerged-arc or brush-arc configuration, where the electrode is immersed in the slag or a short distance above the slag (Mc Dougall 2013). The electrode equipment is divided into an upper and a lower electrode assembly. The self-baking Söderberg electrode is made from lengths of steel casings that are added to the top of the electrode column and welded into place. Carbon electrode paste is added to the inside of these casings and is baked to form a solid tip in the region of the contact shoes. The working platform that surrounds the area where new electrode casings are added, is electrically isolated from the building and each electrode is isolated from the others to ensure the safety of the personnel who perform the electrode casing additions.

Jan 1, 2019

By P. Hansman

"Place Dome Canada&apos;s Detour Lake Mine is a low-grade gold producer located in northeastern Ontario. Production is targeted for 2850 tonnes of ore per day. As reserves and mining areas continued to be found below and far to the west of the shaft (Fig. 1), it became necessary to review and upgrade the materials handling facilities. This paper deals with the selection, design and construction of an underground crusher and conveyor system capable of handling up to 450 tonnes per hour from the lowest existing level in the mine.BackgroundThe Detour Lake mine site is accessed via secondary Highway 652 which runs northeast out of Cochrane, Ontario. The road consists of 200 Ian of hard top followed by 100 Ian of well maintained gravel to the mine site. A 1500 m airstrip is maintained at the mine site for emergency use. Prior to 1991, the workforce was flown to and from the mine site. Crews were now bused to the site from Timmins. Remnants of a winter road exist to the southeast which at one time ended in La Sarre, Quebec. This was the route used to haul bulk items during the construction period and early production years.A town site has not been established at the site for the current operations. Instead, a rotational scheme is being utilized whereby most personnel will work seven days on site followed by seven days off site. For some employees, however, the work week is termed as a four/three schedule where they work 42 hours between Monday at 10:00 a.m. and Thursday at 4:00 p.m. with the following three days off. All surface employees and maintenance employees underground work 12-hour shifts. All underground employees work a lOV2-hour shift. Supervisors work a similar schedule as their crews, however, other staff may overlap their rotation during the week.A five-compartment shaft was sunk in 1984 from surface to the 610 m elevation. Shaft stations were established at the 120 m, 260 m, 360 m, 460 m, and 560 m levels. The cage compartment consists of a single deck, 4O-man cage in balance with a counterweight. The cage hoist is an Ingersoll-Rand 10H and is regulated to travel at 4.1 m/s. Two 9 t skips operate in balance at a travel speed of 7.1 mls. The skip hoist is a 3.05 m drum Nordberg. Both hoists are automated to function without a hoistman during normal skipping and cage service runs."

Jan 1, 1995

By H. T. John

"The objective of this paper is to demonstrate how the optimum cut -off grade can be calculated for typical large tonnage openpit mines. In the examples, it is assumed that the concentrator tonnage is fixed and that there are no market restrictions. The mining rate is assumed to be variable. This is usually the situation at an operating property.ModellingA model of the ore body is required to examine alternate cutoff grade strategies. The model must be accurate in its relationship between grade and tonnage. Table I shows a typical relationship between ore tons and grade for various cut-off grades. The average strip ratio is also shown. For higher cutoff grades, the ore tonnage is decreased and the ore grade is increased. Strip ratio increases with the cut-off grade.Using the relationship between ton s and grade, and assuming a homogenous, long life orebody, a simple calculation of the optimum cut-o ff grade can be made. The objective is to maximize the present value of cash flows. For the long life homogenous orebody example this objective is satisfied by maximizing present cash flows.Cash flow is calculated by subtracting operating cost from revenue . Operating cost will increase with the cut -off grade as the strip ratio increases."

Jan 1, 1985

By Richard R. Klimpel, Simon Isherwood

"The industrial processing of ores containing gold and/or platinum minerals is generally mining site specific, e.g. McQuiston and Shoemaker (1985). The variety of various mineral processing techniques employed is extensive and includes size classification, gravity concentration, amalgamation, roasting, cyanidation, chemical leaching, ion ex-change/solvent extraction and froth flotation. Because of the relatively small quantities of Au and Pt that exist in the earth’ s crust, the economical recovery of Pt and Au often requires that the Au and Pt be associated with other industrially important minerals. This association of Au and Pt with other minerals can occur in very complicated mineralogical forms. It is probably safe to say that Au and Pt mineral concentration from natural ores represents some of the most complex metallurgical challenges facing the mining industry.Froth flotation is a technique that is receiving increasing industrial attention for the treatment of finely disseminated and/or associated Au and Pt minerals. The high throughput at relatively low capital cost, the potentially high selectivity, and the existence of a well-established technology for treating more abundant associated minerals such as base metal sulfides makes froth flotation an attractive processing alternative. Broadly speaking, the industrial oriented froth flotation experience with Au and Pt minerals exists in two major categories: 1) the flotation of Au and Pt associated with pyrite (or pyrrhotite) and 2) the flotation of Au and Pt associated with primarily Cu, Zn, or Cu/Pb/Zn containing sulfide ores.In the case of the precious metal association with pyrite (or pyrrhotite), much of the published froth flotation experience comes from South Africa. Typically, such processes are done using an acid side flotation with a collector such as mercaptobenzothiazole. The approach obviously is to float pyrite and hence recover associated gold. Generally the higher the total sulfur recovery the higher the gold recovery. Similar experiences of Pt associated with pyrite are a lot less common mineralogically and hence less well documented industrially. For example, in Canada, Pt is often associated with pyrrhotite but is not really processed as a straight pyrrhotite recovery.For the situation of Au and/or Pt associated with other base metal sulfide minerals, the industrial experience base is quite varied and is well documented from both North and South American operations. The nature of most of these flotation processes is to design, operate, and optimize the installed concentrator to get the Cu, Pb, Zn, Ni, etc. that is the bulk of the valuable sulfide ore and then take whatever precious metal recovery comes. Typically, such flotations are on the basic side using standard thiol collectors such as xanthates, dithiophosphates, thionocarbamates, etc. It is very common with such ores to use mixtures of collectors in order to get ""everything"". Often in such plants, there is an inherent balancing act occuring so as to operate in such a manner to reject pyrite (and pyrrhotite) in order to maintain high base metal mineral concentrate grades and yet recover sufficient precious metals such as Au and Pt minerals which often are associated with the iron sulfides being rejected. Obviously in such an environment, the smelter operation often ends up telling the concentrator what the precious metal recovery actually was in a given production period."

Jan 1, 1994