Search Documents

By R. J. Johnston

"INTRODUCTIONPoint Mines is located about 65 miles east of Hay River on the South Shore of the Great Slave Lake. It is connected to the Northern Alberta Railway System by the Great Slave Lake Division of CN Railways at Roma Junction, Alberta.The operation started in the fall of 1965 with a capacity of 5000 t.p.d. An addition was put into operation late in 1968 to bring the capacity up to 8000 t.p.d. The present milling rate is 11,000 t.p.d.The location of Pine Point Mines is such that long end cold winters are to be expected end temperatures of lower than -200F are encountered from late October to late March, with extended periods of -300F being common in January and February.It was recognized by Cominco engineers during the initial design period that since freezing would be encountered with open pit ore somewhere in the crushing circuit, the problem was to reduce it as much as possible. Other mines, working under similar conditions, found that the fine ore bins feeding the grinding circuit were the main problem area. The decision was reached, therefore, to have heated fine ore bins and to make sure thst the ore was sufficiently warm to prevent freezing.CRUSHING PLANT FLOWSHEETThe crushing plant has a standard open flow circuit (flowsheet). Ore from the stockpile is loaded into R-50 Euclid trucks by Caterpillar 992 Front End Loader with 11 cu. yd. bucket and dumped into a 42 x 65 C.A.C. Superior Crusher driven by a 300 HP motor. The crusher is set at a nominal 5 inches. The ore falls through into a 100-ton surge bin. There are high level and low level nuclear gauges to allow the primary operator to optimize for optimum orientation."

Jan 1, 1972

By David Whittle

When does a project with questionable viability, warrant further investment? There are cases in which projects, which evaluate to a negative mean probable value, are worth investing in. There are also cases in which projects that evaluate to a positive mean probable value, should not be invested in. The author will present a model for ?project-control?which includes an adaptation of a well know grade-control concept. Comments on Resources and Reserves ?Resource and Reserve estimates are based on positive information (43-101). ?Reserve and Resource confidence qualitatively assessed. ?U.S. Geological Survey (USGS) recognizes Undiscovered Resources (U.S. Geological Survey 2003).

May 1, 2006

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

By T. J. Yeomans

"The Kidd Creek metallurgical site is situated twenty-six kilometres east of Timmins, Ontario. The site consists of a 4.5 niillion tonne per year concentrator, a 127,000 tonne per year electrolytic zinc plant and a 79,000 tonne per year copper smelter/refinery complex.The concentrator commenced operations in 1966 and was expanded to its present capacity in 1978. The zinc plant commenced operations in 1972, and the copper smelter/refinery in 1983.The concentrator tailings, and both liquid and solid waste products from the other plants are disposed of within a 1215 hectare tailings disposal area. Here, a method known as centraljzecl thickened discharge is used to form a stable cone-shaped hill. A low permanent perimeter dyke structure encloses the cone and directs cone run-off and thickener overflow to a treatment pond. After treatment with lime slurry, this neutralized effluent is recycled to the metsite and also discharged into the Porcupine River system.The tailings system has been in operation in its present form since 1972, upon completion of dykes and a 110 metre thickener unit. Underflow densities were continuously increased until thickener overloading became a serious problem. This necessitated the construction of a second 110 metre thickener, which was completed in 1983. Target densities have been achieved without difficulty since then.This paper discusses the operation of the tailings system, reviews past performance, and outlines future operations."

Jan 1, 1986

By Francis Chartrand

The Kwyjibo deposit is an iron oxide Cu-REE-F-Mo-Au mineralization of Mesoproterozoic age located in the Grenville Province approximately 120 km NE of Sept-Îles, Quebec (Figure 1). Occurring along the SE margin of the Canatiche granitic complex, the deposit is composed of several polymetallic showings that are related to different textural facies of magnetite. The mineralization process at Kwyjibo is complex, and is divided into Early Granitophile, Magnetite, Main Polymetallic and Specular Hematite stages (Cayer et al., submitted for publication). The Main Polymetallic stage, comprising chalcopyrite, pyrite, fluorite, molybdenite and REE-bearing minerals, is superimposed on pre-existing magnetiterich rocks. Discovered by SOQUEM Inc. in 1993, the Kwyjibo deposit shares many characteristics with other hydrothermal polymetallic iron oxide deposits around the world. Foose and McLelland (1995) suggested that this class of mineralization could occur in the Grenville Province. However, only a few polymetallic occurrences are known to be associated with low-Ti iron oxide deposits in the Grenville. Kwyjibo is one of the most significant examples of a polymetallic iron oxide deposit to have been found in the Grenville Province to-date.

May 1, 2003

By R. E. McElvain

"Hydraulic transportation of solids in suspension with water or other carriers, such as oil is becoming more practical as economic situations develop with respect to the railroads and other carriers. Of significant importance, is also the increased size of the major operations and the total impact of larg- er tonnages and more critical sources of supply.There are several means of imparting energy into the solids and directing the material down a pipeline, but the centrifugal pump is emerging as the most practical piece of equipment when considering relatively large flows and recent development. We can now handle relatively high densities without interruptions. This provides the mining and transportation fields a more economical means of lifting and transporting coal and other mineral products.Equipment & MethodsWarman International has developed several methods of alternate PDP against high heads. We have, at least for the present time, shelved our pump which uses clear water to slurry method and have placed our major emphasis on the full development of the centrifugal pump. I personally see several similarities on the alternate reciprocating devices as compared with the steam piston type engine versus steam turbines. The centrifugal pump comes into its most advantageous position at about 2000 GPM and can also show advantages by means of increased mobility, when driving tunnels and in other difficult operations when considering the total economic results. We now have some interesting d<:ta on one 5 mile raw silica sand line designed for pumping at 200-400 tons per h:mr. This is a separate subject on a ""simplified approach to slurry transport"" and paper has been prepared for the Hydrotransport 5 proceedings in Germany this Spring. Reference 1 may be of interest to those who want to delve into the subject further, and I also have some advance copies of this paper."

Jan 1, 1978

By J. A. McLennan, J. M. Ortiz

Nickel laterite deposits are typically formed from tropically weathered mafic-to-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs) or representative dozer regions (RDRs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate “optimum” RDR mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each RDR. The optimum mining elevation is the elevation where the lowest summed cost of “accepting dilution” and “wasting ore” occurs. The reported RDR dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation. The reported RDR lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum RDR mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Jan 1, 2006

By C. Blawert

In previous studies of various HPDC magnesium alloys we found that the corrosion properties of the skin are inferior in comparison to the bulk, However, this is surprising as one would expect better corrosion properties for the finer microstructure of the skin, In a more detailed study using 2 and 6 mm thick sections from HPDC AZ91 step plates, the corrosion results of the original skin, the slightly removed skin and the bulk were compared, Indeed, the corrosion measurements including potentiodynamic polarization, long term polarization resistance measurements and electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin. An explanation for this corrosion behavior was found, on the one hand, in the microstructure concerning especially the amount and distribution of the 13-phase and, on the other hand, in the composition, including the distribution of the most important alloying element Al and of some impurities such as Fe.

Jan 1, 2005

By V. N. Bryant

"1.0 SYNOPSISThe Colomac property, located 137 miles by air northwest of Yellowknife in Canada's NWT. will recover gold from 10,000 tons per day of open pit ore.The decision to proceed with the project was based on a mineable ore reserve of 16 million tons (including dilution) averaging 0.064 oz/ton. After an in-fill drilling program in the latter half of 1988, Colomac's mineable, proven and probable ore reserves were increased to 28 million tons averaging 0.056 oz/ton of gold.A feasibility study completed by Wright Engineers for Neptune Resources in December 1987 examined the possibility of vat leaching followed by C.l.P. and electrowinning. A second feasibility study completed by Wright in February 1988 demonstrated that a conventional agitated leach circuit using a finer grind justified the higher capital cost of this process. This study was accepted and formed the basis of the project authorization.Preliminary engineering commenced in April 1988 and detailed engineering was started in September of that year with the objective of a mine/mill start-up by early 1990.The short time period available to meet the project deadline was additionally challenging, as site access is either by plane year round, and winter road from early February to late March. Normal lead times for equipment design, specifications, quotations and bid analyses were not possible, if the winter road time-slot was to be met."

Jan 1, 1990

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003

By A. Mazhary, T. Huff

Sensor-based ore sorting technology is a growing area of interest due to lower-grade ore deposits and higher costs of processing, among other reasons. Among the sensors currently utilized in the particle sorting industry, X-Ray Fluorescence (XRF), as the only sensor with elemental analysis capabilities, has always attracted more attention. Currently, the bench-scale amenability tests for this sensor are performed using hand-held XRF analysers. However, this testing method overestimates the performance of the XRF sorter, and therefore, the results from these tests can be misleading and are often mispresented. The work presented here was conducted on a copper mine and investigates how the sensor’s sensitivity to copper deteriorates under different testing methods. This work compares and correlates the results of an Olympus hand-held XRF analyser, static, and dynamic sorter responses with the actual grades of the rocks. The results confirmed that, the sorter response was extremely prone to blind spots. Furthermore, the results demonstrated that although the static sorter’s responses were comparable in terms of rock identification to those of the hand-held XRF analyzer and assays, the accuracy of the dynamic sorter response deteriorated both as a function of grade of the rocks as well as the potential for blind spots. INTRODUCTION Sensor-based sorting technology has been gaining increasing attention even by larger mining corporations as ore grades decrease, deposits get deeper and therefore cost of mining and processing increases. There are various types of sensors that are currently being used in the particle sorting industry such as X-Ray Transmission (XRT), Color, Electromagnetic (EM), Near-Infrared (NIR) and others. However, none of the sensors are capable of identifying and quantifying particles by the elemental content, except for X-Ray Fluorescence (XRF). XRF is a non-destructive, surficial analytical technique used to measure elemental composition of materials. X-ray fluorescence happens when a secondary x-ray (fluorescence) is released after a sample is bombarded by a primary x-ray source. From a sorting perspective, the most common and expected issues that are associated with XRF sorting are lower throughputs compared to other sensors due to particle presentation limitation as well as the need to wash the material before introducing to the sorter. However, one important issue that is mostly neglected is how the amenability tests are performed and how realistic the obtained results are. Current amenability test procedure utilises a handheld XRF analyser (such as an Olympus InnovX, as used in this work) on multiple, generally 4, sides of the rock and uses the average measured grade as a criterion for separation. While this is a widely accepted technique, it fails to consider some important factors such as exposure time and the distance between the sensor and the particle. These factors can significantly affect the sorting outcome.

Jan 1, 2019

By Brian Hart, Stamen Dimov

"The Time of Flight Secondary Ion Mass Spectrometer (ToF-SIMS) is unique in that it measures the outermost atomic layers of any material. The technique is particularly suited for determining surface chemical composition of mineral particles. It is most commonly used as a diagnostic tool to measure mineral surface chemical variability in plant and bench top flotation separation processes. Recently, research towards understanding the full capability of the instrument has resulted in the development of new diagnostic applications related to various Au extraction technologies and the development of the ToF-SIMS as a predictive tool for assessing the chemical reactivity of the ore.In this paper we will present a brief review of the ToF-SIMS technique with recent advances in instrumentation and methodologies including:•,?recent developments and advances towards a semi-quantitative approach to the evaluation of mineral surface modifiers (ex. Cu),•,?flotation case studies investigating activator, depressant and collector loading variability within a flotation process,•,?the recently developed chemical reactivity test which we believe has the potential to predict the behaviour of minerals in a flotation test in response to chemical transfer during grinding,•,recent applications for determination of surface Au preg-robbed in carbonaceous materials.A portion of this material has been recently presented at the COM 2009 meeting and at SIMS XVII (see Dimov et al 2009 and Hart et al, 2009).INTRODUCTIONIn flotation seperation surface chemistry is the principal determinant for selective separation of the various mineral phases (Ralston, 1994, Smart et al, 2003). Determination of this hydrophobic/hydrophilic balance by particle therefore requires correct identification and selection of the particular mineral phase(s) followed by a statistical analysis of the surface chemical characteristics of the particles with an estimation of the spread of values (Smart et al, 2003)."

Jan 1, 2010

By B. H. Kim

It is hypothesized that the standard approach adopted to characterize the ground and to determine the rock strength properties at depth are flawed and generally tend to underestimate the rock strength and possibly the stiffness, particularly when the rock mass is characterized as massive to moderately jointed or blocky to very blocky. It is therefore necessary to conclusively established that the hypothesis, that the rock strength in highly confined rocks is greater than generally anticipated, is actually valid and generally applicable, and then to develop new procedures to establish rock parameters that can be reliably used for the design of deep excavation.

May 1, 2009

ABSTRACT This paper details the work of RISKGATE, the largest Australian Coal Association Research Program (ACARP) occupational health and safety initiative to date. The program is an interactive online risk management system developed to maximize health and safety performance in the coal mining industry by implementing continuous improvement in managing major unwanted events. The comprehensive knowledge base covers tires, collisions, fires, isolation, strata control underground, ground control open cut, explosions, explosives, manual tasks, and slips/trips/falls. All major Australian coal mining companies contributed topic experts to this broad industry initiative: nine coal mining companies, more than 80 experts, and more than 400 days of individual time for knowledge-capture workshops.

Jan 1, 2014

By Michael I. Brittan, Craig M. Sams

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations using very large SAG mills fitted with variable speed drives. Low-aspectratio single-stage SAG mills were introduced in South Africa to process the consistent gold bearing Witwatersrand quartzites. Elsewhere, circuits were patterned after the more conventional North American circuits with high-aspect-ratio SAG mills followed by ball mills. This paper provides information on two recent Gold Fields group installations covering both types of SAG mill in large, single-stage applications. While these operations process similar tonnages, the mills represent opposite ends of the aspect-ratio spectrum. The Tarkwa mine in Ghana employs a low-aspect 27’ x 42’ 14MW SAG mill. The St Ives mine in Australia operates a conventional 36’ x 18’ 13.4MW SAG mill.INTRODUCTIONGold Fields is one of the world’s largest gold producers with annual production of approximately 4.2 million ounces. The Gold Fields group has operations in South Africa, Ghana and Australia, along with numerous exploration sites and advanced projects in several other countries. This paper discusses new milling operations in Ghana and Australia.TarkwaThe Tarkwa Gold Mine is located in Ghana, West Africa, approximately 350 kilometers west of the capital city of Accra (Figures 1 and 2). The site conditions are tropical with an average annual rainfall of 1,930 mm and a maximum temperature of around 35°C."

Jan 1, 2006

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

By Andre Vien, Jean-François Dupont

"Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the installation and use of such a device on a SAG mill at the Holt-McDermott Mine. Comparison to measured static volumetric load and bearing pressure and inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed. INTRODUCTIONWhile the measurement of load is very important in all kinds of grinding applications, the biggest benefits are expected from AG and SAG milling. This is what motivated Holt-McDermott to take a closer look at this problem, with a view to optimizing SAG mill performance.In many cases, the SAG mill control problem can be stated as maximizing throughput while avoiding a volumetric overload, with the other constraints (e.g. power, grind size, upstream/downstream equipment constraints, etc.) playing a less important role. This is certainly true at Holt-McDermott where the SAG mill is the production bottleneck about 90% of the time, and anything that can be done to increase SAG mill throughput will have a significant impact on operating profit.Although the goal of maximizing throughput while avoiding volumetric overload is simple to state, it has proven to be much more difficult to achieve. The mineral processing industry has expended a great deal of time and effort to devise control strategies in the pursuit of this objective. While much progress has been made, there is still room for considerable improvement. Across the industry it is probably fair to say that overloads occur relatively infrequently, but the real losses accrue as a result of the tendency to run rather conservatively."

Jan 1, 2001

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999