Search Documents

By Wenbin Zhang, George W. Poling

"Prior or simultaneous addition of ammonium sulphate can, not only enhance the activating effect of hydrosulphide ions on xanthate flotation of malachite but it can also eliminate possible detrimental or depressing effects of excess residual hydrosulphide . Use of relatively inexpensive ammonium sulphate appears to reduce the consumption of the much more expensive sulphidizing agent for optimal flotation recovery INTRODUCTIONOxidized copper minerals float poorly with conventional thiol-type collectors. This is believed to be due to the nonadherent character of the collector coating, which is readily re- moved by particle abrasion. Rosas and Polingr reported emulsion flotation seemed capable of resisting abrasion during the flotation of non-sulphide copper ores. It appears that the most common flotation technique for oxidized copper minerals comprises sulphidization with Na .S and subsequent treatment by sulphydryl collector. The principles of this method are available . Malghan recently reviewed the studies on the role of sodium sulphide in the flotation of oxidized copper, lead and zinc minerals.It is well known that in the sulphidized flotation of malachite, the activation process depends strongly on the concentration of the sulphidizing agent, i.e., insufficient sulphide gives poor recoveries because of inadequate sulphidization; excessive sulphide also causes poor recoveries due to the depressive effect of the residual hydro-sulphide ions in solution. A major difficulty in sulphidization, especially with a varying feed nature, is to establish and maintain the optimum sulphide concentration in solution. In plant practice, vigorous control of sodium sulphide is required and stepwise addition of the reagent is recommended to improve the efficiency of the process. Soto and Laskowskim have found that malachite, depressed by an excess of sulphide ions, can restore its floatability if air or oxygen is introduced to the pulp. They attributed this to the oxidation of the HS - ions on the surface of the mineral. Jones and Woodcockuvi showed that a sulphide ion selective electrode could be used to optimize the conditions (e.g . amount of hydrosulphide, sulphidization time, flotation time) more readily and precisely than existing methods in the flotation of oxidized copper ores."

Jan 1, 1989

By P. K. Kaiser, F. Amann

"Rock mass characterization for deep underground construction and mining offers many challenges. This paper first describes some of the key challenges when characterizing highly stressed brittle rocks and then offers some guidance on how to arrive at reliable rock mass strength parameters for deep mining applications. Focus is placed on characterization for rock mass strength determination. It is illustrated how the common use of currently available rock mass characterization systems tend to underestimate the strength of rock at depth. Modifications to currently adopted approaches, i.e., the use of Geological Strength Index GSI for rock mass strength determination, are presented.INTRODUCTIONFor green fields projects, the first challenge of rock mass characterization stems from a lack of access to examine the rock mass at scales larger than typical core sizes (i.e., ~63mm in diameter) until late in the mine design when the flexibility for making changes is constrained. Hence, rock mass characterization often has to rely on information derived from boreholes alone (e.g., core, logs, etc.). This challenge is lessened when mines are expanded from existing operations. A second challenge is related to changing rock mass behaviour with increasing depth and stress. At depth, the rock is highly stressed, thus closer to failure, and often highly confined which leads to a higher interlocking with elevated strength but more brittleness. The goals of rock mass characterization are to be tailored to the technical goals of an investigation. For example, for cave engineering, the workflow includes the assessment of five key engineering aspects (Brown, 2007): Caveability; fragmentation; cave performance; extraction level stability; and mine construction (rock support). Each engineering aspect has to address specific engineering questions and each design component is influenced by different rock mass behaviour aspects and thus is dominated by different rock mass properties, e.g., the vulnerability to stress fracturing (spalling), the bulking characteristics for flow control and support selection, and the confining stress impact on pillar or support design. An effective rock mass characterization program, including logging, mapping and laboratory testing, thus has to collect and interpret features that are relevant for the above listed purposes. Some of the predominant factors are: block volume of defected and non-defected rock; spalling strength; tensile strength of defects; rock mass modulus; and rock mass strength parameters for application to low and high confinement design aspects."

Jan 1, 2015

By S. K. Paul

"This paper briefly describes the underground crushing and conveying system at Sherritt Gordon Mines' Ruttan Mine. A series of three steel-cord belted conveyors, with a total length of 2J55 metres and a total vertical lift of 407 metres, convey the muck from the underground crushing station to the mill at the surface. The maximum size of the crushed rock is 6 in. All the conveyors are provided with numerous safety and fire suppression devices. IntroductionThe Ruttan Mine of Sherritt Gordon Mines Limited is located 20 km east of the town of Leaf Rapids, 760 km north of Winnipeg. The orebody is multilensed, with lens width varying from 6 to 45 m. Ore production started in 1973 with the opening of a 10,000-tpd open-pit mine. Initial development of the underground mine was started in 1972 with the driving of parallel conveyor and access declines at minus-2507o gradient to the I 220-m level, and then the access ramp was further extended to the 1160-m level. Exploration drifting was done on the 1280-m and 1160-m levels from the access ramp. The final development plan for the underground project was approved in January 1977, and full-scale development and constructionwere resumed.At present, Ruttan Mine is in a period of transition from open-pit to underground mining. Ore production is now coming from both operations. By mid-1980, open-pit production will cease and all production will come from the undergroundmine.The underground mining method at the Ruttan Mine is sublevel open stoping with delayed backfilling. The orebody is divided along strike into a series of 27-m-long stopes and 15-m pillars, both 60 m high."

Jan 1, 1980

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Numerous schemes have been proposed in the past to evaluate the shear strength of rock discontinuities based on in situ and laboratory testing. Due to scale effects, in situ testing is the most reliable way to assess the shear strength parameters. However, practical reasons often impede this kind of testing. This is unfortunate because advances in theoretical rock mechanics are still dependant on qualitative experimental works. This paper presents a mobile high capacity shear apparatus developed for in situ direct shear testing of discontinuities along with testing methodology. The apparatus has the advantage of being simple, although of high capacity, and can be moved to different site locations for other tests. The in situ test was performed on a natural rock outcrop of schist with subvertical schistosity. A concrete block 50 x 50 cm with a base layer of high strength mortar was cast on the rock surface. Prior to the test, the concrete block was lifted and repositioned to have an unbonded joint but with interlocking asperities. The shear load was applied perpendicularly to the schistosity direction. The test was conducted in a constant normal load (CNL) condition. Both normal and shear loads were applied manually. The instrumentation consisted of two load cells for shear and normal loading, eight displacement laser extensometers for shear, normal, and lateral displacements and fourteen acoustic emission sensors for monitoring evolution of asperities’ degradation during the test. The friction angle obtained is 72° for the peak and 58° for the residual. The high values of friction angle indicates that first-order roughness and good interlocking of the joint surfaces can result in high shear strength parameter values in a rock generally regarded to have low values.

Jan 1, 2015

By Jaime V. Ongpin

"The author will give a capsule history of Benguet Corporation and attempt to identify its operating environment and underlying ""strategy"" until 1974, when the company's management assumed office. The company's operating environment and ""interim strategy"" from 1975 to 1980 will be described. The discussion will cover an environmental forecast and define the company's"" strategy for survival"" for the balance of this century.IntroductionIn December last year, I was asked to deliver a pa per for the management lecture series a t the Asian Institute of Management in Manila. The paper was entitled "" The 1970's: A Decade of Disaster For New Mining Projects"" . In that paper, it was my task to review the results of new mining projects in the Philippines during the previous decade. The task was not a happy one, for the results themselves were not only unhappy, but disastrous on a scale unprecedented in Philippine history. Out of a total of 17 major mining project s involving an aggregate capital investment in excess o f US $2 billion during the 1970s, only three project s have been profitable, and all the rest have either gone "" belly up"" or are teetering on the very edge of financial disaster.It is in the context of this shocking record of widespread financial dislocation in the Philippine mining industry, (which in varying degrees appears to have been paralleled in virtually every other country in the world where mining is an important sector of the economy) that I address myself tonight to the theme of this symposium. My paper is entitled ""Risk Management Strategy in Mining"" and it is sub titled ""Can Benguet Corporation Survive to Celebrate its Centennial in 2003?"". I have inserted the word ""Strategy"" and added the subtitle, because I wish to make it clear first, that my presentation to you tonight will be focused exclusively on the strategic aspect s of risk management, and second that I will limit myself to Benguet's own ""in-house"" experience and perspectives on this subject. I would caution you therefore, to consider my views within this restricted framework, and in light of the particular and sometimes peculiar circumstances within which Benguet Corporation operates."

Jan 1, 1983

By Stéphane Chevrel

Non-energy raw materials are vital inputs for the EU?s economy and maintaining fair and undistorted access to these materials for EU industry and citizens is increasingly difficult. Within the EU, exploration and extraction have to face increased competition for different land uses and a highly regulated environment. While the EU is currently dependent on the importation of many metals, the overall potential for mining and quarrying in Europe is strong. In spite of this, the land area available for extraction in the EU is constantly decreasing, turning access to land into a key challenge for the extractive industry. The EOMINERS project aims at contributing to demonstrate how to improve the EU capacity in implementing new mining sites and their societal and environmental acceptability. The overall aim of EO-MINERS (Earth Observation for Monitoring and Observing Environmental and Societal Impacts of Mineral Resources Exploration and Exploitation) is to bring into play EO-based methods and tools to facilitate and improve interaction between the mineral extractive industry and the society in view of its sustainable development while improving its societal acceptability. EO offers a unique opportunity to collect necessary spatial parameters that play a key role for better assessments of mining-related environmental and societal impacts. It could enable the development of means to identify the site-specific environmental and societal footprints of mineral resource extraction and to determine their respective significance. This understanding of global and cumulative footprints along a causal chain is needed in order to target policy measures. In this way the expected reduction of environmental and societal footprints in the mining sector can be most effective for the environment and more cost-efficient for public authorities and commercial operators. The project first defined environmental, socio-economic, societal, and sustainable development indicators and criteria that can possibly be dealt with using EO techniques. After an analysis of policies related to the environmental and social footprint of mineral industries, project expertise and stakeholder interviews (national and on-site) as well as site investigations led to the establishment of a list of indicators to be monitored, either directly or indirectly, through accessible parameters. Development of EO-based monitoring tools is then carried out over three demonstration sites: the lignite open pit of Sokolov in Czech Republic, the Mpumalanga coalfield centred on the town of Emalahleni (previously Witbank) in South Africa, and the Makmal gold mine in Kyrgyzstan. From these developments, it is subsequently intended to contribute to the development of generic, standardised EO data integration schemes, in particular in view of characterising affected ecosystems, populations, and societies and prepare indisputable documents that will make the basis for a sound ?trialogue? between industry, governmental organisations, and stakeholders. This paper discusses results obtained after three years into the project, focusing on product development over the demonstration sites and their relevance to the observation and monitoring of environmental and societal footprints of the extractive industry.

Aug 1, 2013

By D. Kershaw

"A world-scale surface mining operation is associated with the Syncrude Oils ands Plant. Each day over 300 000tonnes of oils and are mined and transported to the process plant to produce 129 000 barrels of synthetic crude oil.Examples of research and maintenance engineering programs which have resulted in substantial gains in dragline and bucket wheel conveyor system productivities are discussed. Two central themes within these programs, which go beyond the usual technical support associated with a large surface mining operation, are pursued:1. the approach taken to determine the causes of component failures and provide Syncrude performance specifications to allow manufacturing industry to respond with more appropriate products; and2. systems and equipment studies which have led to higher productivity in the major mining equipment and the development of an auxiliary feed system.IntroductionA world-scale open pit mining operation is associated with the Syncrude Oils ands Plant located near Fort McMurray in northern Alberta. Over 300 000 tonnes per day of oils and are mined and transported to the process plant. Fifty million barrel s of synthetic crude oil were produced in 1987, which represents 10010 of Canada's crude oil requirement.following tree clearing and surface drainage, overburden is removed by mobile equipment ahead of oils and mining. Draglines excavate the 40 m depth of feed grad e oils and which is windrowed on the dragline bench. Bucketwheels reclaim the oils and from the windrows for transport by conveyor systems to the extraction plant surge pile.The Syncrude mine is operated in four essentially equal quadrants, each serviced by a dragline and a bucketwheel conveyor system. The mining face in each quadrant is approximately 2 km long and reclaimed oils and is transported by 1830 mm shift able conveyors over distances up to 6 km. Individual conveyors vary in length up to 2500 m.The Syncrude plant started operating in late 1978, and Figure I shows the mine production history through to the end o f 1987. Annual production volumes have increased from 50 million tonnes of oils and in 1979 to 105 million tonnes in 1987.The period from 1982has seen a change in operating philosophy, away from striving for very high production rates, to operating at sustained targetted levels within the measured capacity of the equipment. Higher over-all production volumes have resulted from being able to operate for more hours at these rates. This same period has also seen much greater emphasis placed on routine inspection of the equipment and planned preventive maintenance to avoid problems which could otherwise impact on production."

Jan 1, 1990

By Bruce K. McKnight

"The new H-W orebody was evaluated by considering its production at three technically feasible rates. Capital and operating costs were estimated f or each rate and production sequences were established using mining cutoff limits generated by an ore value algorithm. The viability of the project was then examined by conducting economic and financial analyses of each of the three production cases under various world economic scenarios. These analyses employing standard profitability measures demonstrated all three cases would be economically viable; the production case which maximized the Net Present Value of the project was the one selected for development and production.IntroductionWestmin Resources Limited and its predecessor company, Western Mines Ltd., has been continuously carrying out mining operations near Myra Falls in Central Vancouver Island since December 1966. The mining operation, whose current production rate is approximately 830 tonnes / day (t/d), based on ore derived from the Myra and Lynx Mines, produces copper, lead and zinc concentrates which contain significant quantities of gold and silver in addition to the base metals.In the late 1970s, with Lynx and Myra ore reserves slipping to unacceptably low levels, a major increase in mine-site exploration was initiated, with outside geological staff brought in to complement the efforts of the mine's geological staff. By the end of 1979, this program had resulted in the discovery of a significant new orebody on a deeper horizon some 300 metres below the one which hosts the Lynx and Myra deposits. Throughout the period 1980-1982, major drilling was carried out to evaluate the new H-W deposit and by the end of 1982, drill-indicated mineral inventory for the deposit compared with Myra, Lynx and Price ore reserves was as shown in Table I. During this same three-year period, a major development and evaluation program was underway comprising environmental monitoring and control programs, shaft sinking test mining, bulk sampling and mill testing, rock mechanics studies and preparation of the Stage I and II reports for the multidisciplinary Environmental Land Use Committee (ELUC).As a result of the preliminary engineering work and exploration drilling, it became rapidly apparent that the H-W deposit could support a considerably higher production rate than the current one. Accordingly, engineering studies including scheduling of development and production as well as capital and operating cost estimates, were focused on three possible production rates: 1350, 1800 and 2700 t/d. Our task was to select the optimum one of these three rates."

Jan 1, 1987

By P. W. Percival, J. J. Janssens

"Whitehorse Copper is a 2600-ton-per-day underground copper mine located within the city limits of Whitehorse, Yukon . In early 1978, due to increasingly difficult ground conditions. it was decided to investigate the conversion from longhole open stoping to vertical crater retreat mining. On-site crater testing by C-I-L demonstrated the feasibility of V.C.R. mining at Whitehorse Copper.After some investigation. a down-the-hole drilling rig was chosen and drilling began in November /978. Blasting began in June /979. and to September 1980 approximately one million tons of ore had been blasted. In-field changes to both drilling and blasting techniques have been implemented. Some of these changes were dictated by problems encountered; others were made to improve efficiencies.To date. V.C.R. mining has proven successful from a drilling and blasting aspect.IntroductionWhitehorse Copper Mines Ltd ., a division of Hudson Bay Mining and Smelting Co., Limited , is a 2600-Lp.d. underground copper mine. The plant site is located I mile west of the Alaska Highway, and approximately 7 miles south of Whitehorse city center. Production is from the Little Chief orebody, and total output is from vertical crater retreat stopes.The Little Chief and Middle Chief orebodies at Whitehorse Copper had original reserves in excess of 6 million tons, most of which graded 2.00/0 copper or higher . The orebodies are typical skarn deposits that have developed along the contact between an intrusive diorite and a limestone-quartzite flank pendant. The limestone has been metasomatized to form a calcium-magnesium skarn which, along the limestone / quartzite contact, has locally further developed into a mineralized magnetite-serpentine skarn. The principal copper minerals are bornite and chalcopyrite, with minor chalcocite and valleriite. Skarn gangue minerals are serpentine, diopside, garnet, epidote, calcite and wollastonite. Appreciable values in gold with some silver are present and recovered as well."

Jan 1, 1981

By G. E. Bogin, C. Strebinger, J. F. Brune

"Evidence shows that methane gas emanates from the mined-out area or gob of a longwall coal mine and can travel towards the working face, posing an explosion risk. Since the gob consists of varying levels of compacted rock, many researchers have modeled fluid flow through the gob as a Darcy-type porous media with a specified porosity and permeability. When studying methane gas explosions near the gob fringe, the Darcy flow assumption may not be applicable to describe the methane flame interaction with the gob. Computational fluid dynamic studies were performed modeling methane flame propagation across a simulated gob which was modeled as both a Darcy porous medium and as discrete rock objects with varying sphericity. Modeling the gob as a Darcy porous medium results in unrealistic methane flame propagation since the porous media assumption does not consider any differences in rock size and/or distribution. Additionally, the porous media model does not allow for ignition within and subsequent flame propagation through the porous medium, which must be modeled to understand the potential for methane gas explosions in the gob area. Modeling the gob as discrete rock objects produces more realistic methane flame dynamics and agrees with experimental observations. Modeling results show flame propagation across circles, hexagons, and squares, meant to represent rock rubble in the gob, produce different levels of turbulence which affects methane flame propagation velocity. This research demonstrates that modeling methane gas explosions in a longwall coal mine environment, specifically near the gob area, requires modeling obstacles, such as rock rubble, as discrete physical objects to capture the complex coupling of fluid dynamics, thermodynamics, and heat transfer. INTRODUCTION Although there are methods to mitigating methane accumulations in a longwall coal mine, explosive gas zones (EGZs) of methane and air may exist and pose an explosion risk to nearby miners and equipment (Brune, 2014) (Karacan, Ruiz, Cote, & Phipps, 2011). In the event of an explosion, the resulting methane flame and pressure wave can be catastrophic as evidenced by the Upper Big Branch explosion in 2010 that killed 29 miners (Page, et al., 2011). Since the mining process is transient, it is difficult to determine exactly where these EGZs exist, but investigative reports show in many cases, these EGZs can be near the working face, behind the shields, or within the gob area (Brune, 2014) (McKinney, et al., 2001). Additionally, miners have recounted seeing flames moving back and forth within the gob and under the roof supports (McKinney, et al., 2001) and in other cases, anecdotal evidence of hearing small pressure pops deep within the gob area (Brune, 2014)."

Jan 1, 2019

By A. C. Moerman, C. W. Pelley, K. R. Notley

"The software package described in this paper facilitates the handling of diamond drilling information in the creation and maintenance of a geological information database. Once entered, the drilling information is stored in a direct access file for rapid retrieval. The drill data are sorted into vertical cross sections and interpretation is performed using on-screen menus to define areas of common rock type and outline the mineralized zones. Intersections of individual zones can then be examined and outlined in the longitudinal dimension at a graphics terminal.With the aid of surface-fitting routines, the digitized information can be used to generate three-dimensional models of each zone. From these models intermediate cross sections and level plans can be obtained. Several interpretations are possible and plotter drawings can be obtained. An output file for use by ore reserve estimation software can also be created.Future work will tie this software to geostatistics and mine planning programs and will be aimed at converting mainframe software to run on microcomputers. IntroductionComputer applications in underground mine planning and geology are not new. Operations such as Sherritt Gordono and Kidd Creek have been using software developed about a decade ago for handling geological information and designing stoping blocks. However, general use of such systems has been limited mainly due to the cost of hardware which was affordable only to large corporations. Software to perform the work was usually developed on site and was largely unavailable for use by others, being site-specific, or too expensive for other organizations to purchase.The increasing power of microcomputers and mini-computers, and their relatively low cost compared to the mainframe computers which were previously used, has led to the increased use of computers at mining operations of all sizes. Sources of software for use in geological interpretation and mine planning have increased in number with the proliferation of the use of microcomputers."

Jan 1, 1988

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By O. J. Restrepo-Baena, L. Rojas-Mendoza

Gold losses must be controlled during extracting processes, especially during cyanidation. Otherwise recovery decreases and therefore the profitability of projects too. One of the phenomena that generate such losses is known as preg-robbing which occurs when some mineral constituent adsorbs aurocyanide complex from a cyanide solution. There are some laboratory methods to identify potential preg-robbing in gold ores, highlighting the PRP method, the BGMI test, and cyanidation tests by conventional agitation without activated carbon (BRP) and with activated carbon (CIL). For this study we performed an initial characterization of a sample from Antioquia - Colombia and then we carried out the methods described above in order to identify the presence of carbonaceous matter. We obtained a percentage of preg-robbing of 78.7% by applying the BGMI test; the preg-robbing potential by the PRP method was 97.9% with an extraction of 0.77% and an inferred recovery of 36.6% if preg-robbing did not occur. Finally we obtained under the BRT test a recovery of 0%, while for CIL test an extraction of 33.6% what confirmed the presence of preg-robbers agents in the gold ore. We conducted all tests in the Institute of Minerals - CIMEX at Universidad Nacional de Colombia - Medellin.

Jan 1, 2014

By V. G. Papangelakis, G. P. Demopoulos

"Recovery of gold from refractory ores and concentrates presently constitutes one of the most important, challenging, and exciting areas of R&D activity in the gold processing industry. New technologies are being tested for the treatment of refractory gold materials, some of which have been advanced to the level of commercial operation. In this paper, some recent technological developments in the hydrometallurgical processing of pyritic matrix-refractory gold ores are highlighted. Key operational steps of each of the alternate hydrometallurgical technologies are analyzed and potential advantages and drawbacks are identified. The processes which are reviewed are: hydro chemical oxidation, biochemical oxidation and pressure oxidation. INTRODUCTIONOver the years the term ""refractory"" has been applied in gold ore processing to denote situations in which straightforward cyanidation failed to yield high gold recoveries. A number of mineralogical and chemical factors may be responsible for this ""refractoriness"" problem. A systematic classification of the different options for their treatment has been discussed in a recent review paper. In this paper, the pretreatment of the submicroscopic gold encapsulated within the matrix of pyrite and arsenopyrite minerals is considered. This type of gold is the ultimate refractory material because complete breakdown by reaction of the host mineral structure is required.The method which has been traditionally applied for the treatment of pyritic-type refractory gold ores is an oxidation roast (single stage or double stage depending on the As content) of a flotation concentrate to produce a porous calcine, the latter being more amenable to cyanidation. Despite its established practice, oxidation roasting is not considered particularly attractive with today's standards for high product recovery and clean environment. Roasting is known to be very sensitive to heating parameters and feed composition and deviation from optimum conditions can result in reduction in permeability which is translated to incomplete gold liberation."

Jan 1, 1989

By M. Bozorgtabar

Metal Matrix Composites (MMC) have a ductile matrix containing ceramic particles, Due to their improved wear properties, Al?SiC composites have economical applications in many industrial uses where wear is a problem, One of the most serious difficulties in manufacturing Al-SiC composites is obtaining adequate 'wetting' of the particles by the melt. In this research work, a stir casting system was designed for the improved manufacturing Al-SiC composites, The effect of some production variables such as the addition of SiC particles to the aluminum melt on wettability, was also studied. The results showed that the manual addition of particles would not be successful in manufacturing and that a system of adding silicon carbide particles through controlled temperature, atmosphere and improved mixing was needed.

Jan 1, 2005

By M-A. Thibault, C. Gauthierand, J-P. Gagné, J-Y. Carrier, P. Rochette, G. Dufour

"Anodes consumed in the electrolytic process for the production of primary aluminium are considered consumables. They need to be replaced at regular intervals of approximately one month. The so-called anode butts which are removed from the cells contain the metal supports (rods), cast iron thimbles, crust and residual carbon material. Cleaning is required to remove the waste material before the rods are fitted with new anodes. An inspection is required to ascertain if repairs to the rods are necessary. Presently, this inspection is carried out visually. ST AS, in 2004 in collaboration with Alcoa Deschambault, initiated a project to develop an automated inspection system. The objectives were to find a technical solution to perform these functions with a very simple system. Such a system was designed around ""artificial vision"". The inspection system developed uses only one fixed camera and does not require a separate step in the process for the anode rod assembly to perform the inspection. This paper presents the initial steps of the work performed to develop the equipment and software as well as a summary of the results obtained."

Jan 1, 2006

By Walker. P. W. A.

Abstract -The Riviera tungsten occurrence in the Cape Province of South Africa was discovered in October 1979 as a result of stream-sediment panned concentrate sampling. The Cape age granite and late Precambrian Malmesbury Group carbonates and chlorite schists which it intrudes and which host the mineralization are covered by between 10 m and 30 m of Tertiary/Recent alluvium and clay. The scheelite/powellite and molybdenite mineralization occurs in a greisenized granite cupola with an overprint of porphyry-type alteration as well as in minor skarns. The ore reserve is estimated to be 46 million tonnes at an average grade of 0.2160Jo W03 and 0.020% Mo. The deposit is uneconomic at current tungsten prices.

Jan 1, 1994

By Raynald Vézina, Richard Leclerc, Jean Boissonnault, Louis P. Gignac, Gérald Veillette

Since mid-1989, Cambior has increased its producing gold mines from four to six, having acquired the Chima Mine and brought the Silidor Mine onstream. In June 1990, the company announced that the Mouska project would also be put into production. Gold production reached almost 190 000 ounces in 1989 and is expected to exceed 220 000 ounces this year. Cambior has also a non-gold operation with an interest of 50% in the Niobec Mine and has recently signed an option agreement in the development of the Lac Knife graphite deposit in northeastern Quebec. During the past year, the company has extended its exploration activities to the United States and Indonesia, and now has interests in nearly 80 properties. Last May, Cambior signed an option agreement with Golden Star for a gold deposit in Guyana, the OMAI Project, containing at least 2 000 000 ounces of gold in situ.

Jan 1, 1990

By L. Mercier, R. Narendrula, F. Desmarais, L. Amaratunga, A. Aledresse

Thiosulfate is recognized as a promising alternative lixiviant to cyanide for the extraction of gold from ore bodies. Gold thiosulfate ([Au(S2O3)2]2), however, is not well-adsorbed by activated charcoal, making industrial scale use of thiosulfate for gold leaching impractical at present. Because of their high specific surface areas (500-1000 m2g-1) and uniform open-framework nanoporosity (pore channel diameters in the range 3-10 nm), functionalized mesoporous silicas are widely recognized as highly effective materials for the selective, rapid and high capacity uptake of mercury, gold and platinum group ions. In the present work, the efficient and rapid adsorption of gold thiosulfate by thiol-functionalized mesoporous silica (hereafter designated MP-HMS) is demonstrated, whereby the thiol groups in the materials bind with the gold complexes by ligand displacement. The adsorbed gold could be leached out using cyanide, regenerating the adsorbent for further uptake cycles. Functionalized mesoporous silica is thus a promising candidate for the preconcentration of gold from thiosulfate leachate solutions.

Jan 1, 2011

By Mike McKevitt

We are trying to promote a concept and a change in management?s approach to the iterative process of grade control. This is important as grade control must routinely try and achieve the long term objectives set by the mine plan ??BackgroundBackground ??Factors contributing to variation from planFactors plan ??Basis of OptimisationBasis Optimisation ??Ore Block Optimisation processOre process ??Operating mine examplesOperating examples ??Chain of Mining. ??Intention is to highlight the need for repeatable and consistent materialand material-type classification to remain consistent with the Life of Mine Plan ??We can drill another hole or reWe re-optimise a plan, but once excavated, the final decision has been made ??The grade control decision is the last decision made in the resource exploitation sequence.

May 1, 2009