Search Documents

By C. O. Staples, J. G. Morrow

The application of cationic flotation to the upgrading of magnetic concentrates was investigated in the laboratory by both batch and continuous test procedures. It was found that the collection of coarse gangue particles with amine, heretofore considered a serious obstacle to this particular application of cationic flotation, is greatly enhanced by a drastic reduction in what might otherwise be considered normal impeller speed. Gangue flotation is in-dependent of variations in the rate of aeration. The collector and Crother additions and the impeller speed which favour the formation of a matte froth yield optimum results.

Jan 1, 1966

By K. Kawagishi, K. Matsumoto, Y Koizumi, H. Harada

A new burner rig for cyclic and hot corrosion testing of Ni-base superalloys and high-temperature coatings has been developed at the National Institute for Materials Science (NIMS) in Japan. The concepts of the rig design include: use of kerosene as fuel, easy operation for materials research and multi-specimen testing capability per test run. The burner rig consists of six blocks including combustion block, corrosion-solution injection block, furnace block, specimen block, controller block and outdoor facility block. During verification testing, it was confirmed that the rig had accurate specimen temperature control within ±1? from 600 to 1100? and automated easy operation. Cyclic testing of several Ni-base superalloys was conducted. The results from 50 cycle testing indicated that a new NIMS alloy developed for 1700? class gas turbine had higher oxidation resistance than CMSX-4. This new burner rig testing capability at NIMS can be very useful for future oxidation, hot corrosion and coating durability studies.

Jan 1, 2010

By C. Mattich, Å. Holmström, L. Hedström

"The fluidized bed at Division Ministro Hales (DMH) division of Codelco in Calama, Chile is currently the largest operating roaster for partial roasting of arsenic rich copper concentrates. The roaster converts the Mina Ministro Hales (MMH) enargite rich (Cu3AsS4) copper concentrates into calcine with a low arsenic content that is suitable for mixing with other copper concentrates feeding a flash furnace. The plant sets a new standard for the processing of arsenic rich concentrates, both from the quality of the calcine as well as the environmental performances. The process technology and expertise are based on the solid practical experience of treating arsenic rich concentrates from both the Boliden smelter and Outotec.The partial roasting process is located next to the mine and concentrator and includes a sulphuric acid plant with auxiliary equipment. The produced calcine has an arsenic content significantly below target and the residual sulphur meets the requirement of the flash furnace. The plant operates with high efficiency cyclones resulting in a low amount of calcine passing to the hot electrostatic precipitator (HESP). The small flow of HESP calcine dust can be combined with the low arsenic calcine and still meet the flash furnace feed arsenic requirements.SO2 formed during roasting is converted into sulphuric acid, while volatized arsenic is recovered in the wet gas cleaning section of the acid plant along with a large proportion of antimony present in the MMH concentrate. Arsenic is stabilized as calcium arsenate and sent to disposal at a specially prepared site.The present production rate (September/October 2015) is close to or higher than the original maximum design capacity of the plant.INTRODUCTIONMineralogyThe mineralogy of an ore and concentrate is important, since there is a direct link between roasting performance and concentrate mineralogy. The MMH concentrate has a good combination of minerals that makes the roasting process efficient and flexible. The main minerals are pyrite, enargite and chalcocite (Figure 1). The inert content is about 15% and consists mainly of silicate and alumina based minerals. The lead content is very low and this is desirable, since the presence of even a small amount of lead will cause a substantial increase of sintering during roasting."

Jan 1, 2016

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By Francis Breton, Lei Pan, Kun Liu

"Effects of Fe, Cu and Mg minor alloying elements on creep properties of 8xxx aluminum conductor alloys were investigated by conducting compressive creep tests at 100 ºC under a constant load of 69 MPa. The microstructural evolution was studied using an optical microscope and electron backscatter diffraction technique. The creep properties were characterized by the primary creep strain in the first stage and the minimum creep rate in the second stage of creep deformation. Results showed that additions of all three minor alloying elements (Fe, Cu and Mg) demonstrated a beneficial effect on the creep resistance but individual alloying elements exhibited different impacts on creep properties. The additions of Fe and Mg showed a strong impact on both the primary creep strain and minimum creep rate, while the Cu addition displayed a favorable effect on the primary creep strain but no impact on the minimum creep rate. Microstructure observation revealed that with increasing Fe contents, the volume fraction of fine intermetallic dispersoids gradually increased while the subgrain size and misorientation angle became smaller, providing strong barriers to the dislocation and grain boundary movements. The addition of Cu moderately reduced the subgrain size and misorientation angle and in combination of solid solution strengthening it promoted the retardation of the creep deformation during the primary stage.INTRODUCTIONThe 8xxx aluminum conductor alloys offer significant advantages such as low density, high conductivity to weight ratio and low price over copper conductors and become an attractive candidate in electrical engineering and building wiring (McQueen, Chia, & Starke, 1986; Birol, 2009; Engler, Laptyeva, & Wang, 2013). The mass resistivity of aluminum conductors is one-half of copper conductors. Thus, only one-half the weight of aluminum is required for equivalent capacities. Therefore, this unique property coupled with a relatively low price of aluminum offers significant economic advantage to develop aluminum conductor alloys for electrical applications in the electrical wire industry."

Jan 1, 2016

By Richard Lavallée

La Mine Louvicourt est une mine hautement mécanisée exploitant un gisement polymétallique avec des chantiers transversaux minés et remblayés selon une séquence primaire-secondaire. Dans certaines parties du gisement, il n'y avait qu'un accès à la coupe inférieure, car il n'était pas rentable d'avoir aussi un accès par coupe supérieure. Le minerai situé au-dessus des chantiers avec trous ascendants était considéré comme ressource non rentable par minage mécanisé. L'option de miner ces ressources avec des sous-niveaux avec accès par monterie alimak et forage long-trous de petit diamètre fût donc étudiée et démontra une rentabilité intéressante, particulièrement en considérant les tonnes ainsi minées comme tonnage supplémentaire au tonnage planifié. Dans ces chantiers, les détonateurs électroniques ont été très utiles et de plus, les coûts d'explosifs ont étés réduits considérablement par l'utilisation d'émulsion pompée en vrac.

Oct 1, 2004

By K. G. Markkola

The Minera Candelaria concentrator was commissioned in August 1994, and in October 1997 it doubled its grinding capacity. The concentrator was designed to treat 56,000 metric tonnes of copper ore with a primary crusher, two grinding circuits, pebble crushing, and flotation. The grinding circuit includes two 11.2 m (36 ft) diameter by 4.6 m (15 ft) long semi-autogenous (SAG) mills, each fitted with a 12 MW motor. Throughout the history of Candelaria, different strategies have been developed to maximize the plant's operational time, strategies that include increasing the life of the SAG mill liners and reducing the time involved in changing these elements. This work describes the improvements made in the design of the liners, the change planning, and a new strategy to change the liners with the purpose of increasing their use and throughput.

Jan 1, 2007

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By Masatsugu Morimitsu

This paper introduces new technology of oxygen evolution anodes which can be applied to produce copper, zinc, cobalt, and other metals by electrowinning. The anode consists of nano iridium oxide particles dispersed in amorphous tantalum oxide matrix as a catalytic layer formed on a titanium substrate. The anode can reduce oxygen evolution potential by 0.25 to 0.55 V compared to commercially available lead alloy anodes and can suppress unwanted side reactions such as manganese oxyhydroxide, lead oxide, cobalt oxyhydroxide which occur during oxygen evolution in the electrowinning solutions. This technology is effective for environmentally friendly electrowinning processes with low energy consumption and less anodic deposition.

Jan 1, 2011

By J. A. Finch, A. M. Elmahdy

Blending frothers is becoming common in flotation practice apparently enhancing performance. However, there have been no studies to understand the blend mechanism. In this paper, the effect of two frother blends ofF150 (polyglycol) with MIBC or pentanol (both alcohols) on bubble size, gas holdup and froth height is reported. The blends focused on a small addition of the polyglycol to the alcohols as base frother. The tests showed that the bubble size at blend concentration below the critical coalescence concentration (CCC) of the base frother was decreased but was significantly larger above the base CCC. Froth build-up showed a strong synergistic effect.

Jan 1, 2009

By N. Saracoglu, R. H. Wallis, J. E. Betz, F. L. Jagodits, B. R. Krause

"Geophysical test surveys were conducted with various methods (EM, lP, gravity and magnetic) over the McClean uranium deposits of the Canadian Oxy- lnco Joint Venture. The result s were assessed to judge the contribution each method might make toward further discoveries of graphite-associated uranium occurrences.The best drill targets have proven to be discontinuities in graphitic conductors and locations where the tatter are intersected by fracture zones in the Athabasca. The tests demonstrated that the preferred combination of geophysical survey s is horizontal loop EM to locate graphitic conductors in the basement and VLF-EM to locate the fractures.IntroductionThe discoveries of the McClean North and South uranium deposit s (Fig. 1) are essentially geophysical successes resulting from drilling MaxMin delineations of INPUT airborne electromagnetic responses (Saracoglu et al., 1983). After the initial discovery in 1979, various geophysical methods, techniques and instruments were employed to test their effectiveness in this environment and to guide exploration for other deposit s of a similar nature in the remainder of the 260 km2 property.The McClean uranium deposits lie below 150 m to 180 m of overburden and Athabasca Group. Radioactive signatures might be expected; however, the Athabasca Group acts as a barrier to radioactive emanations. Fortunately, the uranium mineralization is associated with graphite in the crystalline basement. Prior drilling of ground electromagnetic anomalies confirmed that EM surveys could locate and out line basement graphitic conductors. However, as there were many anomalies, most of which could not reasonably be expected to be associated with uranium , there was need to identify additional parameters, related to mineralization, which could be detected geophysically and used to narrow the search."

Jan 1, 1986

By M. J. Nicol, C. van Wensveen

The kinetics of the oxidation of thiosulfate by copper(I I) in ammoniacal solutions have been studied in the presence and absence of dissolved oxygen. The formation of an intermediate mixed ammine/thiosulfate copper(II) complex ion has been confirmed and the rate of the reaction monitored by simultaneous on-line spectrophotometric, dissolved oxygen and potentiometric measurements. The rate of the anaerobic oxidation of thiosulfate by copper(II) was found to be orders of magnitude slower than that in the presence of dissolved oxygen and is inhibited in the presence of ammonia and anions such as sulfate and chloride as a result of competition with thiosulfate for the axial coordination sites on the copper(II) tetrammine complex. In the presence of dissolved oxygen, it was found that the copper(I) thiosulfate complexes are only very slowly oxidized while the copper(I) diammine complex is rapidly reoxidised to the copper(II) state. Thus, the initial rapid reaction with copper(II) leads to a pseudo steady-state condition in which the concentration of copper(I) is relatively constant and the rate of oxidation of thiosulfate can be predicted from the measured rate of oxidation of copper(I) by oxygen in ammoniacal solutions. The effects of the concentrations of ammonia and thiosulfate on the oxidation rate can be rationalized on the basis of the above coupled to the species distribution of copper(I) in the ammonia/thiosulfate system. It is shown that, with relatively simple measurements of dissolved oxygen and copper concentrations, the rate of oxidation of thiosulfate can be predicted under typical leaching conditions.

Jan 1, 2005

By D. R. Wright

"The modest thermal efficiency of the steam turbine cycle essentially determines the heat required and, therefore, the coal consumption and ash production of pulverized-coal-fired powerplants. This paper emphasizes how some properties of coal and its ash can crucially affect the operation of a steam generator and its flue gas cleaning equipment. A brief reference to some siting factors and economics reaffirms the all-pervasive influence of the properties of coal and ash and establishes the importance of a firm supply of cooling water. The economics of scale remains a compelling factor in selecting the size of units, despite disappointing performances by some of the larger units. Environmental considerations suggest that smaller units still have a role to play. IntroductionCoal fuelled one industrial and economic revolution, beginning two hundred year s ago . It was the precursor of competing fuels, notably natural gas, oil and uranium, which eclipsed it in terms of convenience and rate of growth.The turmoil that now exists because of rapidly dwindling supplies of no-longer-cheap oil and the concerns about nuclear energy-justified or unjustified-exacerbated by an operating incident at the Three Mile Island Nuclear Powerplant, prompt speculation for a resurgence of coal, especially where it cangenerate electricity to replace energy from imported oil.The world's reserves of coal are not inexhaustible, although they are ample for several decades. Of greater import is the fact that the world's coal reserve s are more widely distributed than its oil reserves, and they appear less convenient as instruments of economic and political persuasion by opportunist powers. The crux is whether or not the world will accept all that a massive, if temporary, return to coal implies.Combustion of pulverized coal in steam generators to pro duce electricity is a 50-year-old, well-understood technique; it is undergoing continuous refinement to meet evolving environmental and economic criteria and is not found wanting. It is certainly the only technique available and technologically advanced enough to replace oil immediately on a large scale. Although it may take a decade to bring a new coal-fired powerplant into service, this delay is a reflection on nontechnical and administrative processes. Capital and operating costs of coal-fired powerplants are significant and subject to inflation, but, because of the accumulated experience in this field, the ability to control costs is better than for those energy processes which are less mature or still in embryo form. More exotic, soft energy systems, touted as the panacea for world energy problems, have still to prove themselves on the scale they are needed and under the stringent climatic and operating conditions coal-fired powerplants have already mastered."

Jan 1, 1980

By B. Arsenault

Aluminum coatings can provide galvanic cathodic protection for several metals and alloys, In order to be a suitable protective solution on structural components, the mechanical integrity of the component must be preserved, In particular, fatigue properties are a challenge for thermal-spray protective coatings on mechanical structures, To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc-sprayed protective coating, different surface preparations prior to arc spraying were considered, In the present work, a feasibility study was performed using laser ablation as a surface-preparation technique before or during arc spraying of coatings, This was collaborative effort between the LERMPS laboratory in France, the National Research Council Canada and the Royal Military College of Canada, Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate-surface-preparation techniques including laser ablation (Protal® process), grit blasting and shot peening. Results indicate that a combination of key conditions, including the use of nitrogen as the arc spray gas, shot peening, and proper laser energy density for ablation, provide high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates.

Jan 1, 2005

By C. Anderson, H. Huang, P. Miranda, E. Dahlgren, I. Chandra, M. Jeffrey

The latter part of the 20th century saw great advances in the treatment of refractory gold ores coupled with increased reliance on the use of cyanide for gold processing. Now, in many parts of the world, there is social pressure to limit or eliminate the use of cyanide. As well, treatment of some refractory ores or concentrates which have excessive cyanide consumption, gold cyanide pregrobbing or significant sulfide content remain difficult. This paper will outline the history of the development of alkaline sulfide leaching as an ancillary process to nitrogen species catalyzed (NSC) pressure leaching. Electrochemical fundamentals and the applicable thermodynamics of the alkaline sulfide hydrometallurgical system will be outlined. As well, examples of refractory gold recovery with alkaline sulfide hydrometallurgy such as an arsenopyrite gold concentrate application, a chalcopyrite gold concentrate application, a pregrobbing gold ore application, and a cyanide consuming gold ore application will be delineated in this paper.

Jan 1, 2005

By J. F. Dorion

This paper presents the results of on-going investigations on the performance of support systems in Québec underground mines. The focus of these investigations is on site observations complemented by laboratory investigations. Of particular interest is deducing the corrosion rate, at selected mine sites, as determined by the installation of monitoring coupons.

May 1, 2009

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"In January 1974, the Minerals Division of Canadian Occidental Petroleum Ltd. made the strategic decision to add uranium to its active exploration commodities and through compilation studies selected northern Saskatchewan as the most attractive and cost-effective exploration area in Canada. In August 1974, 100 sq. miles were staked adjacent to Gulf Minerals' Rabbit Lake deposit and east of the Esso Minerals Midwest boulder train. Initial exploration was based on geologic models of the Rabbit Lake deposit.In the summer of 1975, surface surveys delineated radon anomalies which were drilled that winter and found to overlie anomalous concentrations of uranium in the regolith which forms the upper unit of the crystalline basement. Within the crystalline basement, one hole intersected graphite and pyrite with anomalous nickel-cobalt-arsenic. Geochemical and radiometric surveys followed in the summer of 1976. Drilling in the winter of 1977 intersected several zones of graphite and also anomalous, but uneconomic, uranium abundances. Also in 1977, Dahlkamp and Tan (1977) described the coincidence of graphite and uranium at Key Lake and ground EM surveys on CanadianOxy claims detected graphite conductors beneath 250 ft of Athabasca sandstone. Inco Limited joined the project in April 1977 as a 50% partner. The project area was then surveyed using the airborne INPUT EM method, which detected 84 miles of conductors, with associated graphitic metasediments. On the ground these were located with MaxMin surveys, and follow-up drilling located the ""Tent"" Lake uranium zone.In 1978, the Midwest and Dawn Lake discoveries were announced, 7 miles and 2 miles west of the Joint Venture (J.V.) claims; and, in part for this reason, the 1979 winter drilling was concentrated on the deeper west side of the property. Exploration hole 102-79 intersected altered and uraniferous rocks, but stepout holes were barren. Drill hole 153-79 tested an under-snow three-station radon anomaly east of hole 102-79 and intersected 33 feet of 7.51 % U3O8, confirming the disco very of the McClean North zone. The geophysical grid of the McClean North conductor system was extended and detailed a strong, continous conductor to the south, called McClean South. This was drilled in January 1980and hole 1004-80intersected 22 feet of 2.95% U3O8."

Jan 1, 1983

By Jehan Rondot

Des quartzites très pars ont été dêcouverts au cours de la cartographie de la region du lac des Martres, étape de l'étude géologique de la region de Charlevoix. On distingue quatre groupes métasédimentaires, tons con tenant des niveaux de quartzite dans an moins deux domaines géologiques différents, c'est à l'ouest, clans le domaine gneisso-charnockitique que se situent les quartzites du groupe des Martres. Quartzite et gneiss à grenat et sillimanite, en banes épais, constituent la formation de La Galette. A Pest, dans un environnement gneisso-granitique, les deux groupes métasédimentaires de Saint-Siméon, et de La Malbaie comprennent, par contraste, des bancs pen épais et de compositions variées. Les niveaux de quartzite dépassent rarement 50 m d'épaisseur. L'autre groupe metasédimentaire, celui de Saint-Tite des Caps, recoupé de nombreuses intrusions charnockitiques et granitiques, ne possède que de minces niveaux de quartzite. La pureté et la grande épaisseur des quartzites de La Galette suppose une histoire complexe qui se termine par des depots continentaux de climat aride, par opposition aux depots marins des autres groupes. D'autre part, la presence de ces quartzites an sein de roches Presque anhy¬dres et de haute temperature que sont les charnockites leur confère des caractéristiques de fusion sans decrepitation. Parmi la multitude de depots de quartzite qui existe clans le monde, peu sont de qualité supérieure. Or, de par sa composition chimique, le quartzite de La Galette se compare avantageusement à ceux des meilleurs gisements des Etats-Unis, de l'Europe de l'Ouest et de l'Afrique du Sud. D'accès facile pour l'exploitation, les gisements ne sont qu'à une trentaine de milles de Baie Saint-Paul ou de La Malbaie, sur le Saint-Laurent. L'utilisation en metallurgic prévue pour le quartzite de La Galette comprend la production de silicium, de ferro¬silicium et d'autres alliages de silicium. La composition du quartzite est en outre appropriée pour la production de carbure de silicium et de silicate de sodium. Les fines peu¬vent être utilisées pour la fabrication du verre et comme matière de charge.

Jan 1, 1977

By Shahé Shnorhokian

Numerical modeling is increasingly being used as a tool to examine complex geomechanical issues related to rockmass behaviour and stability of underground openings. The in-situ stress regime and the evolution of mining-induced stresses during the life of an operation, taking into account the planned stope sequence, are topics that can only be handled through the use of a realistic and calibrated numerical model. This paper presents a case study of a deep underground Canadian mine in northern Ontario. A FLAC3D model was constructed and calibrated based on in-situ stress measurements. In the first stage, the evolution of stress regime was studied and compared with the occurrence of rockburst events during a period of three years. The locations of clusters were examined and compared to the mining sequence during that period. In the second stage, stresses within a diminishing ore pillar were examined based on the planned stope sequence and compared to levels deemed acceptable to the mine. Based on the results, an alternative sequence was arrived at to reduce stress accumulation in the pillar, or induce it to occur at a further distance from a brittle dyke in the vicinity of the orebody.

Aug 1, 2013

By E. Wright

"INTRODUCTIONThe Ruttan Mine is located twenty-two km east of Leaf Rapids in northwestern Manitoba. The copper-zinc exhalative massive sulphide deposit is comprised of a series of individual and interconnected en echelon lenses which strike east 20 degrees north and dip south 70 degrees. The mine has been owned and operated by the Hudson Bay Mining & Smelting Company since July 1987. Sherritt Gordon Mines Limited began mining the orebody in 1973 from an open pit, but production has been entirely from underground since 1980. HistoryDuring the progression from open pit to underground mining, it was recognized that manual methods of ore reserve calculation were inadequate for responding to changing metal prices and evaluating alternative mine plans. The mine planning system that was developed is described in the paper, ""Computerization of Ore Reserves and Mine Planning Functions at Ruttan Mine"", presented by B.C.W. Haystead at the 1984CIM Annual General Meeting. At that time, programs for core logging, diamond drill hole plotting, grade interpolation, ore outline digitizing, and reporting had been developed by the Systems Department for use on Sherritt's UNIVAC 1100 mainframe computer. Telecommunications linked terminals at the Ruttan coreshack and office to the UNIVAC in Fort Saskatchewan, Alberta. The same mine planning system was also used at a second property.Operation of the mine planning system was expensive, and it was evident that increased use required a costly upgrading of the UNIVAC in order to maintain an acceptable service level to all users. The system was re-evaluated,' and it was concluded that: core logging was not easily adaptable to a new property, nor flexible enough for exploration; plotting, grade interpolation, and digitizing required considerable manual effort; and that the UNIVAC operating system was difficult to learn.It was recommended that a study should determine if: core logging could be redesigned and/or implemented on a microcomputer; interactive graphics be used to reduce the effort for functions requiring visual interpretation; and the creation of input processors would assist users in setting up parameters for guiding the programs."

Jan 1, 1989