Search Documents

By R. H. McCorkell

"Sample drops were evaporated on Lexan disks on which fission tracks were etched and counted after neutron irradiation. [U] = 0.01 ppb could be measured. This method is rapid, cheap, simple and accurate when sufficient control and checking is possible, but several types of error were encountered in its use, the natures and sources of which were investigated but not always determined. The most troublesome were ""annealing"" processes which sometimes altered the fission tracks so that they were not fully revealed, or acquired varying appearances, after etching. Several different annealing processes seemed to exist and seemed to be produced by alteration of the Lexan surface by dissolved components in the solutions and, perhaps, by radiation and local heating during neutron irradiation. The appearances of the etched tracks varied with the natures of the droplet solutions even when annealing appeared to be absent, and for this reason, standards are best prepared by additions of known amounts of U to sample solutions. Contamination of sample droplets by U-containing dust from the air is best avoided by preparing the disks away from areas where other U-analysis is being carried out.IntroductionFission tracks are regions of radiation dam age produced in solids by the fission of atoms such as 235U. They can be enlarged to sizes visible through optical microscopes by etching surfaces through which they pass with solvents in which the solids are slightly soluble. A sample to be analyzed for U may be placed against a film of a solid of negligible uranium concentration (the track detector) and irradiated with thermal neutrons in a nuclear reactor to fission 235U. The track detector is then etched and the number of tracks per unit area, ?, which is proportional to the uranium concentration of the sample, c, and the neutron do se, n, is found by counting through a microscope. Uranium in solutions ha s been measured by evaporating drops on track detectors, irradiating, etching and determining the number of tracks per drop, T(2,3,4,5). Extensive test s of this method are reported here."

Jan 1, 1983

By F. Goodarzi

"The nature and distribution of the inorganic components and the concentration of certain environmentally sensitive elements, such as, As, Sb, B, Hr, Cd, CI, F, Mo, Pb, S, and Se, or elements detrimental to the utilization by industry such as B, Na, P and S are very important in determining coal quality. The concentration of elements in coal is controlled by the following factors: (1) frequency of occurrence of partings; (2) nature and habit of occurrence of minerals in coal; (3) environment of coal deposition; (4)rank; (5) geological setting; and (6) weathering.Selective mining of coal can reduce the input of undesirable elements such as As and S by eliminating the part of the seam which is enriched in these elements. IntroductionCoal is a sedimentary rock of plant origin and consists of two components: an inorganic component (minerals) which is formed by influx of clastic sediments into the coal-forming environment and also by activities of groundwater, and an organic component (macerals) which is formed from plant debris deposited in the original coal-forming environment. However, coal is a generic term with a broad range of utilization characteristics. A coal that is attractive for use in one market - such as generation of electricity (combustion) - may not necessarily be acceptable for use in another, such as for production of coke (Davis, 1978).The elements in coal are associated with both macerals and minerals. The elements associated with coal macerals, such as C, H and N are termed elements with organic affInities. The concentration of elements with organic affmities (including B, Br, CI, F, I, S, and Mg) often decrease with increasing ash content of coal (Nicholls, 1968; and Finkehnan,1982). FIgure 1 shows such a trend for chlorine. Some of these elements may also be incorporated in coal maceral as very fine mineral grains (Finkelman, 1982). The elements with organic affmities are often volatilized during combustion and carbonization of coal and emitted in the vapour phase. Emission of some of these elements (C, 0, Br, N and S) is of major environmental concern (Lim, 1979)."

Jan 1, 1994

By N. E. Chaouai, M. Lavigne

"Indicator kriging is one of the non-parametric geostatistical techniques, ideal for estimating the reserves of irregular mineralizations (e.g. gold, uranium, platinum, diamonds, etc.). Such mineralizations are characterized by variograms which are very sensitive to extreme values (outliers) and very difficult to model.The classical approach to this problem in the industry is to trim off these high grades using arbitrary empirical upper limits established either from practice or subjectively. Contrary to this simplistic approach, indicator kriging discretizes the histogram of the grades (usually log normal) in several classes and carries out interpolation separately for each class. This paper gives an overview of the differences between ordinary and indicator kriging along with the steps required to carry out indicator kriging. The paper concludes with a case study involving a gold deposit estimation.IntroductionParametric geostatistics (ordinary kriging) has given us satisfactory results over the years in estimating the reserves of well behaved deposits with coefficients of variation close to 1 (e.g. sedimentary and porphyry type deposits). However, numerous problems have been encountered in estimating irregular mineralizations (e.g. small vein deposits of precious metals) with high coefficients of variation in the range of 2 to 5. Such deposits are characterized by a very small proportion of extreme values (outliers) which create distortions on the variograms (pure nugget effect) and render them useless(1,2).The solution often followed by the mining industry today is to trim off these values based on empirical limits. These limits are derived either by comparison with production results (or bulk samples) or by geological interpretations. Needless to say that such manipulations can lead to serious errors in estimating ore reserves (usually underestimation of total metal quantity), especially when production results or bulk samples are absent.On the other hand, the solution followed by the geostatisticians in the past was to smooth out the data using transforms (e.g. normal-score or natural logarithms). Such transforms are nonlinear and they required non-linear estimation techniques such as disjunctive kriging (DK) or multivariate gaussian kriging (MG) which require normal related hypotheses, not necessarily true in geology.Nonparametric geostatistics (indicator and probability kriging) have been -developed in order to handle these problems related to highly skewed distributions."

Jan 1, 1990

By David Deglon, Martin Harris, Mehdi Safari

"This study investigates the effect of energy/power input on the flotation of a platinum ore in a pilot-scale oscillating grid flotation cell. Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Secondary rougher feed and primary cleaner tail streams were floated in a pilot-scale oscillating grid flotation cell at power inputs from 0 to 2.5 W/kg, using 0.50 and 1.50 mm bubbles. From this study one may conclude that the effect of energy/power input on the flotation rate is strongly dependent on the particle and bubble size. Flotation rates generally increase with increasing particle size and decreasing bubble size. Increasing energy input generally leads to an increase in the flotation rate for finer particles and an optimum flotation rate for intermediate & coarse particles. Optimum conditions for intermediate/coarse platinum ore particles are using small bubbles at low energy inputs, or large bubbles at higher energy inputs. These results suggest that higher energy inputs are generally beneficial for the flotation of platinum ores as these consist predominantly of finer particles (-75 µm) and most industrial flotation applications operate with larger bubbles (1.0-2.0 mm).INTRODUCTIONThere is a considerable body of experimental and theoretical evidence to suggest that energy/power input plays an important role in flotation kinetics, particularly in the finer particle sizes where flotation efficiency is poor (Deglon, 2005). A number of excellent studies into the effect of energy on flotation kinetics have been carried out in impeller stirred cells (Ahmed and Jameson, 1985; Deglon, 2002; Pyke et al., 2003; Newell and Grano, 2006). Investigations using this type of cell have a number of limitations. The impeller influences particle suspension, bubble break-up and agitation in the cell. In addition, turbulence is highly inhomogeneous and anisotropic, with power intensities near the impeller orders of magnitude higher than those found elsewhere in the cell (Deglon, 1998; Koh and Schwarz, 2003; Schubert, 1999, 2008). These limitations have resulted in the development of novel cells for the investigation of energy input."

Jan 1, 2016

By P. Mayer

"Determining the correct mechanism of a boiler tube failure is important for the prevention of future tube failures. Proper corrective measures can be undertaken to alleviate the root cause or causes for a failure only when the correct mechanism is known. A mechanism of boiler tube failure is defined as the process which degrades the tube and produces a failure.An expert system package was developed for use by electric utility power plant personnel during investigation into the cause of a boiler tube failure. It is intended to assist their efforts to recognize and identify a basic failure mechanism that can produce the type of boiler tube failure under investigation. The program guides the user to the most likely failure mechanism by asking simple questions, answers which can be obtained by determining the failure location, type of fuel, and from visual inspection of the failed tube. Expert systems are a form of artificial intelligence which imitate the decision-making process of experts.IntroductionBoiler tube failures (BTFs) continue to be the single largest source of forced outages in fossil fired electricity generating stations. Because of this a concentrated effort is being made to minimize boiler tube failure occurrences. Eliminating boiler tube failures could be worth $5 billion a year to the electric power industry(1).The aggressive service environment of fossil-fired boilers is largely the reason for these failures because the combined effects of stress, temperature, corrosion, erosion and vibration cause deterioration of boiler tube material properties and reduction in wall thickness.Determination of the boiler tube failure mechanism is important for the prevention of future problems. The root cause for a failure can be established and proper ameliorative measures taken only when the failure mechanism is identified correctly. The correct identification of failure mechanism is a complex process which may include many individuals and institutions. Technical specialists in metallurgy, chemistry, combustion, and boiler design frequently cooperate with the station staff in a failure investigation . These individuals rely on personal experience and numerous reports , theories, studies, private communications and investigations concerning the different failure modes and mechanisms."

Jan 1, 1990

By M. R. Babcock

"The Rabbit Lake story began in the late sixties and will continue well into the twenty-first century. It is a story of success, of multiple ore body discoveries, of unique systems, and new methods made possible through innovative and state-of-the-art design. Two quite different geological systems host the five ore bodies mined, or slated to be mined. These two systems have yielded two distinct ore types, each with characteristic mineralogical properties and each requiring its own specific mill circuit.Emphasis on communications and our unique systems have led to a satisfactory and fulfilling work environment resulting in the historically low employee turnover which has contributed to the operation success.A comprehensive environmental study after twelve years of operation has given the Rabbit Lake Operation a completely clean bill of health. INTRODUCTIONRabbit Lake can be described as Saskatchewan's first highgrade uranium mining operation, which set the stage for the province's current role as the leader in uranium mining throughout the western world. The importance of the Rabbit Lake operations - past, present and future.LocationThe Rabbit Lake operation is located in northeastern Saskatchewan (Fig. 1)- 805 km north of Saskatoon, Saskatchewan, and 814 km northeast of Edmonton, Alberta. OwnershipGulf Minerals Canada Limited discovered the Rabbit Lake deposit in 1968. Mining operations began in 1975and were operated by Gulf until purchased by Eldorado Nuclear Limited in 1982. In 1988, Eldorado merged with Saskatchewan Mining Development Corporation (SMDC) to form Cameco-A Canadian Mining &. Energy Corporation. The new corporation is one of the world 's largest uranium companies.Cameco's $1.5 billion in assets include the Rabbit Lake uranium mine (Cameco 100010); the Key Lake uranium mine (Cameco 66.67%; Uranerz Exploration and Mining Limited 33.33%); the Cluff Lake uranium mine (Cameco 20%; Amok Ltd. 80%); the Fuel Services Division at Blind River and Port Hope, Ontario (Cameco 100%); and a 100%); and a 48.75% interest in the Cigar Lake uranium deposit which is now at the test mining stage (Cogema Canada Ltd . 32.625% ; Idemitsu Uranium Exploration Canada Limited 12.875%; Corono Grande 3.75%; Korea Electric Power Corporation 2%). In addition, Cameco is involved in a number of base and precious metal explor ation projects."

Jan 1, 1989

By M. Kuyumcu

With annual production of almost 3.5 million metric tonnes of K20, former East Germany (GDR) was the world?s third-largest producer of potash, ranking behind only the Soviet Union and Canada. More than 80 % of production was intended for export to earn urgently needed hard currency. For this reason, beginning in the 1970s, East Germany began to mine unprofitable hard-salt sources and carnallitite fields, which are geomechanically problematic. In the course of restructuring from a centrally planned to a market economy after German reunification, only two of the nine existing potash mines were classified as economically viable for privatization. All six potash mines in the South Harz Region were closed between 1991 and 1993. The orderly safekeeping of these potash and other decommissioned ore mines and the rededication of mining areas were assigned in 1992 to a German state-owned company GVV founded especially for this purpose. Elaboration in the present documentation covers the local necessity of the type and extent of filling and safeguarding measures. As a result of the remedial measures taken, it was possible to prevent the collapse of cavities and damage to surface facilities. This documentation describes the safeguarding successes to date, with appreciable reduction and stabilization of surface settlement and with significant lessening of seismic events. Also presented are concepts updated to the state of the art for safeguarding of numerous potash mining shafts for long-term effectiveness in separation of the workings and watercourse levels in the cap rock. In the course of 100 years of production, six mining dumps resulted with a total volume of approximately 170 million m3. They consist of up to 95 % of water-soluble salts. Every year, precipitation dissolves up to 500,000 tonnes of this salt, which enters as a highly concentrated solution into watercourses and ground water. Explanation follows of measures for minimization of environmental pollution by covering of dumps and controlled drainage of alkaline solutions from the dumps. Finally, presentation is made of the results of the successful work until now by GVV for reuse of decommissioned mining sites with settlement of new companies for creation of additional jobs and for revitalization of the monostructured South Harz Potash Mining Region.

Aug 1, 2013

"Eastern Canadian thermal coal mined at Minto, New Brunswick, and in western Cape Breton at St. Rose, Inverness County, Nova Scotia, contains 6-8 per cent sulphur. Both coals are high volatile bituminous. types. The Minto coal averages 18 per cent ash, 7 per cent sulphur and has a Btu rating of 11,900 per lb. Pyritic sulphur accounts for 75 per cent of the total sulphur and the remainder is largely organic; the amount of sulphate sulphur is negligible. This means that in a 7 per cent sulphur coal, 2 per cent is organic and 5 per cent pyritic sulphur. Pit-head St. Rose coal contains approximately 10 per cent ash, 7 per cent sulphur and 11 ,800 Btu/lb. The distribution of sulphur is different to that of Minto coal because about 12 per cent sulphate sulphur is present. Thus, a 7 per cent sulphur coal would contain 4 per cent pyritic, 2 per cent organic and 1 per cent sulphate sulphur.The iron sulphides, pyrite and, to a lesser extent, marcassite occur over a wide size range from large sulphur balls to crack fillings, lenses, and individual crystals and framboids. Coarse-grained pyrite and sulphur balls are easily separated during washing. It is the fine grain sizes, intimately mixed with the coal constituents, that are difficult to separate. Quantimet analyses of the fine grains in coal from both localities showed that about 50 per cent were smaller than 30 micron(1).No efforts have been made to wash the Inverness coal of Nova Scotia and in 1980 washing ceased in New Brunswick. Previously, the Minto coal was processed in an antiquated jig circuit which reduced ash from the strip operation run-of-mine value of more than 20 per cent to less than 18. More effective removal of ash and sulphur could clearly be obtained. Laboratory tests on both Minto and St. Rose coal have shown that ash rejection rates of 40 to 50 per cent at yields of 70-80 per cent were possible(2), Little information on sulphur removal was available."

Jan 1, 1981

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract—Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O signature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract-Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O sig- nature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

By D. W. I. Griffiths, J. C. Bélanger

"La Division Matagami de Minéraux Noranda inc. a profité de la construction de sa nouvelle mine (Isle-Dieu) pour continuer sa modernisation.L&apos;utilisation d&apos;automates programmables (PLC) s&apos;est intensifiée pour contrôler et automatiser de plus en plus d&apos;équipement dans ses minessouterraines, au concentrateur, dans les atelierset bureaux.Tous les PLC comrnuniquent entre eux et les IBM PC sont utilisespour exterioriser l&apos;information et faire Ie lien entre Ie personnel et les automates. Le système Central IBM 36 emmagasine les donnees traitees par lesPLC (a travers les PC). Ces donnees sont transmisesau programme d&apos;entretien de chaque equipement et compile les heures, cycles, tonnes, etc., fait imprimer automatiquement les feuilles d&apos;entretien préventif &apos;, etc.Les principales realisations adate et en progrès pour la mine Isle-Dieu sont:• automation complète du système de remblayage du concentrateur ala mine Isle-Dieu situee a2 km de la mine principale;• automation du fonctionnnement des ventilateurs qui comprendra la position des portes de ventilation, Ie chauffage, Ie débit, etc.;• automation des pompes, surveillance des sous stat ions électriques, concentration des gas (CO, SO2) à chaque niveau en tout temps et du propane à l&apos;entree d&apos;air frais;• tonnage et cycles par Ie treuil; et• contrôle d&apos;autres équipernents à differénts niveaux. D&apos;autres travaux furent egalement effectues par les employes, tels que:• la conversion d&apos;un Scooptram ST5A de diesel à électrique;• I&apos;installation complete de systèmes de depoussierage a I&apos;eau (scrubber) pour le concassage secondaire;• I&apos;installation d&apos;un marteau hydraulique avant les concasseurs coniques;• la rénovation des cellules de flottation ; et• l&apos;installation d&apos;un système de gardiennage par caméra. D&apos;autres projets seront effectués ou étudiés:• automation d&apos;un Scooptram"";• automation d&apos;un marteau hydraulique;• récupération de Scooptrarn; téléguidé:• gestion de l&apos;énergie, contrôle de la demande, surveillance et contrôle de l&apos;équipernent de machines fixes(compresseurs, boulloires, pompes à vide, génératrices, débits et pression d&apos;air, eau pour diagnostiquer les problémes, analyser les coûts;• concasseur portatif pour fabriquer de la pierre concassée pour utiliser dans les chemins sous-terre, et• utilisation de micro-ondes pour transmettre les images captées par camera."

Jan 1, 1990

By I. Paredes, R. Díaz, H. Henao

Smelting of copper concentrate generates a significant amount of dusts which are collected in electrostatic precipitators. This material, which is a complex oxide of Cu, Fe, S, As, Sb, Bi and others, is difficult to recirculate into the smelting process due to the reported high concentration of arsenic. However, the dust also has concentration of copper above 10wt %, aside from reported contents of silver corresponding as much as 25wt% of the total inventories of this element in the smelters. Thus, it is of economic and environmental interest the development of a process able to reduce the concentration of arsenic in the dust and produce a material suitable to be recirculated into the smelting process. The present experimental work shows the results of a process of dust sulfidization-oxidition able to remove more than 65wt% of the arsenic present. INTRODUCTION Copper sulfide deposits worldwide exhibit increasing concentrations of arsenic. One case of interest would be the copper ores from the northern zone of Chile, which report high concentrations of enargite (Cu3AsS4) (Revista química, 2015) (Latinominería, 2014). The obtained concentrate from this ore is treated in a Fluidized Bed Roaster, producing calcines with low concentration of arsenic (<0.5 wt% As). This material is suitable to be treated in a Flash Furnace. At the roasting process, the arsenic is volatilized and then precipitated as fine particles of complex oxides. Most of this particulate material is removed from the gas stream through a device called Electrostatic Precipitator (Minería chilena, 2014). The experimental results reported in the literature indicate that arsenic present in these particulate materials (or dusts) cannot be eliminated in oxidizing atmospheres (air) or with inert gases (N2) in a Fluidized Bed Roaster even at temperatures as high as 700°C. There is also information that even the recovery of valuable metals from the dust is difficult through hydrometallurgical processes (private communication). This is how in some foundries these dusts are considered environmental liabilities. Regarding the decomposition of enargite (Cu3AsS4) in neutral atmosphere, it is reported in the literature (Padilla, 2001) that the main chemical reactions are:

Jan 1, 2019

By C. B. Mapes, E. C. Dowling Jr.

"To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.INTRODUCTIONPhelps Dodge commissioned the Morenci Concentrator Filter Plant in 1942 with four 8'6"" Dorr-Oliver cloth disk filters. That year, the filter plant processed 265,537 tons of concentrate grading 20.5% Cu. The filter cake production averaged 9.3% moisture. In 1944, the Extension Filter Plant commenced operation with three additional 8'6"" Dorr-Oliver cloth disk filters. This coincided with the expansion of the concentrator. Production that year totaled 451,567 tons of concentrate grading 23.8% Cu. Moisture averaged 9.4%.Through the years additional filter units have been added in response to increased concentrate production. An Eimco drum filter was installed on the extension side and an additional Dorr-Oliver disk filter was installed on the original side in the 1950's. In 1961, two 8'6"" Peterson disk filters were installed, one on each side to replace two worn-out DorrOlivers. The installation of four 10xl2 foot Peterson drum filters was completed in 1974, coinciding with the Metcalf Concentrator startup. An Eimco belt filter was installed later.The greatest change to concentrate dewatering at Morenci occurred in 1963 with the addition of a 10x60 foot rotary gas fired dryer. The installation also included a number of conveyors to deliver filter cake from both plants to and from the dryers. Other ancillary systems included dust scrubbers and their slurry pumps. The commencement of drying was undertaken due to the rapid increase in cake moisture as a result of the LPF process and the recycling of acid plant scrubber dust slurry from the smelter. In 1972, a second dryer system was installed to increase capacity."

Jan 1, 1993

By Carlos Nieble

Ferteco Mineracao, belonging to the CVRD group, is one of the several iron ore mines in the south east of Brazil. Some of these mines have pit walls of over 350-m height and operations under difficult geo-technical conditions are steadily increasing. In order to mine the 15 million tonnes of high grade hematitic ore remaining in the Fabrica pit, Ferteco had to deal with the following restrictions: Warrant power to its concentrator and pellet plant, relocate the load-out rail road loop, stabilise a poor phillyte slope, relocate a creek on a bench, lower the water table and mine at maximum angles at a slope with phillyte and loose itabirites directly under the rail road loop. Considering these aspects, 3 stages of operations were designed, considering a safe operation, but with the lowest possible security factors at the last mining stage, before the pit would be filled in again with tailings. Stage one above the rail road loop and below the high tension power mast, where the poor phillyte slope was secured by a flexible retaining wall, using old rails and anchors up to 27 meters (80ft) with a working pressure of up till 30 tonnes and stage two with different slope angles, and deep wells, high wall blasting perpendicular to the highwall with relief holes and rerouting the creek in steel half culvert and stage three, the filling in with tailings and recuperation of the deep well pumps. Following studies and analysis were made: Geotechnical and geological studies of all rock formations including rock strength test, a hydrological study to define the lowering of the ground water level, slope stability analysis for every bench and all possible combination of benches, definition of blasting parameters close to the pit slope, a monitoring plan, including topographical movements, vibrations due to blasting, piezometers and pressure cells as well as a plan how to fill up the pit again with tailings in combination with the rising of the ground water level. A close co-operation between the geo-technical consultant, pit operations, the blasting contractor and the geological department resulted in an operation without any incidents, lowering the pit with an additional 3 benches and mining an additional 5 million tonnes of high grade ore.

May 1, 2003

By C. T. Wiliams, John B. Bush, John Lamb

"THE TOWN OF HEDLEY is in the valley of the Similkameen River, about 200 miles east of Vancouver and 25 miles north of the International Boundary between British Columbia and the State of Washington. The main ore deposits are located on Nickel Plate Mountain, northeast of the town.The outcrop of the Nickel Plate system of orebodies is at an elevation of 5,900 feet. It was discovered in 1898 by prospectors and sold in the following year to the Marcus Daly interests of Butte, Montana. Production commenced in 1904 under the name of Daly Reduction Company. In 1909 control passed into the hands of the Hedley Gold Mining Company. Operation of the mine continued until 1930, when exhaustion of known ore reserves forced it to close. Upon the recommendation of Paul Billingsley (3) the mine was optioned by the 1. W. Mercer Exploration Company in 1932. Production began once more in 1934 under the name of Kelowna Exploration Company Limited, and was practically continuous until August 1955, when the mine was again shut down. The name of the latter company was changed in 1951 to Kelowna Mines Hedley Limited.The Mascot Fraction, a small wedge-shaped claim lying astride the Nickel Plate orebodies, was mined by Hedley Mascot Gold Mines Limited between 1935 and 1949. The geological setting and structural control of ore are essentially the same as in the adjoining Nickel Plate Mine.Total production from all operations on Nickel Plate Mountain to the end of 1954 was approximately 3,800,000 tons of gold ore, with a gross value in excess of $48,000,000.General GeologyNickel Plate Mountain occupies the gentle westerly dipping limb of an asymmetrical anticline, the axis of which trends northeasterly. The rocks are composed of a thick pile of Triassic limestone, limy argillite, and quartzite, -resting on a flattish floor of granodiorite near the base of the mountain. Associated with these sediments is a host of porphyritic sills and dykes of gabbro-diorite composition. In the mine area east-west brown soda-rhyolite dykes and north-south black andesite dykes crosscut all the other formations and the ore, probably following steep later fractures."

Jan 1, 1949

By J. Chlan

"Dryer DescriptionProctor and Schwartz Continuous Conveyor DryerThe Proctor and Schwartz Continuous Conveyor Dryer has been in operation since July 1958, and comprises six unit• - an 8• wide single conveyor with roller extruder, insulated housing, type 304 stainless steel circulating and exhaust fall system, steam heating coils, temperature controls and discharge crusher rolls. Entire dryer dimensions are 52’ x 12'0""weighing 53,000 lbs,Extruder rolls - setting is 1/8"" (Drive 3 HP 1800 RPM) clearance off the extruder screen.Conveyor - consists of 151 interlocking pans, measuring 8"" x 8' (2 HP 1200 RPM) One Exhaust Fan (5HP - 900 RPM)Steam Coils -- l"" steel pipe - with steel fins -- each coil measures 16' 2’’- 64 coils in the No, 1 Compartment- 64 coils in the No, 2 CompartmentDryer OperationThe yellowcake slurry at 28% solids is pumped to an 81 x 8' Peterson Filter. The filter media presently being used is a Neotex 4372 blanket, being 100% staple fibre nylon, 12 oz per square yard with air porosity of 9 CFM's. The cake discharge at 45 - 50% moisture falls into the roller extruder. Extrusions are formed by forcing the material by rolls through a perforated plate moving back and forth and depositing the spaghetti-like extrusion on onto the dryer-conveyor.The conveyor now carries the extruded material through the heating chamber•, The feed end of the dryer will be referred to as No. 1 Compartment, with temperature control set at 280""F. The circulating fans take the hot air off the coils and circulate the heated air through the perforated openings in the dryer conveyor pane, After passing through the set of steam coils and circulating fan in No, 1 Compartment, the material then goes through No, 2 Compartment where the temperature is set at 305'F, Final material then discharges through a set of crusher rolls set at ~"". Moisture of final dried product runs at less than 2%.The dryer conveyor load is usually run to a 3"" - 4"" depth load. Conveyor speed at approximately 90 minutes for load to pass through. Load onto the conveyor is controlled by boot level and speed of the 8' x 8' filter. The dryer steam coils are water-washed twice a month."

Jan 1, 1972

By J. W. Jefferies

"Plant availability up 13%, production output up 40%, tons per employee up 15% and labor turnover down 52%. One mine manager states these were direct spin offs from the work being done to qualify for a safety award in the program known as the ""IMSRS 11 over a three-year period of time. ""Of Course"", stated this manager, ""these were in addition to an 87% reduction in our disabling injusry frequency rate.”Officially known as the International Mine Safety Rating System or the Five Star Mine Safety Rating, a new approach to mine safety is being used with enthusiasm by a significant number of mines in Canada, the U.S., Australia, Chile, Indonesia, the Philippines and South Africa. Significant results are coming into the International Loos Control Institute from over 125 mines from these countries.The program is built around a mine safety audit system that gives positive recognition to a mine at 5-step intervals along the way, (a star with each step attained). The Institute has licensed auditors in locations in Canada and the U.S. available to audit.It is believed the success of this program is the result of the premise upon which the program is based. The results being achieved are due to the concept that a modern, well-managed mine safety program maintains the basic foundation of a complete management system. When properly implemented, it reinforces those factors common to production, quality and safety. (Attitude - skill - knowledge - fitness - structure - machine - equipment - materials and processes). The IMSRS contains elements that reinforce all these factors. It uniquely treats safety as part of the ""right way"" to do the job and not just the ""safe way"" as a distinctly separate entity. Mines using this program now recognize that many of the older safety techniques were not necessarily the right way or the most efficient way to do things. It appears that this new approach to mine safety is a new avenue for the attainment of management's real goals for being in business, and at the same time achieves optimum support for the important target of safety and health for the mine worker."

Jan 1, 1983

By John Starkey

This paper examines 5 years of SAGDesign testing data with particular emphasis on the grinding test results from two recent projects, the Fortune Minerals Limited NICO project, and the Aurora Energy Resources Inc., Michelin deposits, located in the Northwest Territories and in Labrador respectively. The context is to compare these results with the SAGDesign database. The required SAG mill pinion energy for these two ores showed vast differences, even though both ores had similar average Bond Ball Mill Work Index values - about 13 kWh/t each for the two deposits respectively. Bond Rod Mill Work Index values for NICO ranged up to 19.7 kWh/t for the hardest ore, confirming the harder nature of the coarse material. SAG mill pinion energy to grind the NICO cobalt-gold-bismuth-copper ore from F80 152 mm to T80 1.7mm varied from 16 to 35 kWh/t, while for Michelin uranium ore, it varied from 2 to 9 kWh/t. NICO ore is harder than any other material encountered to date using SAGDesign testing. SAG pinion energy is more than double the ball mill pinion energy using a transfer size T80 of 1.7mm and a final grind P80 of 74 microns. For NICO, the ore is ?off the charts? for simulation design techniques because there is no comparable operating SAG mill treating ore that is this macro-competent. For Aurora, the relationship between SAG and ball mill pinion energy is reversed in that the SAG mill requires less than half of the ball mill pinion energy using a transfer size T80 of 1.7mm and a final grind P80 of 90?. Because these discoveries are so important for grinding mill design, their impact will be dealt with in future papers, at the August METSOC Conference in Sudbury, and at the September SME Workshop in Tucson. It has now been concluded that the ratio of SAG pinion energy to Bond Ball Mill Work Index, is valuable data to use in designing a SAG/ball mill grinding circuit, to help choose the power split needed.

May 1, 2009

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By M. W. Bartley

"The Steep Rock iron mine is 141 miles west of Port Arthur, Ontario, and 50 air miles north of the Vermilion iron range in Minnesota. The property lies 27'2 miles north of the village of Atikokan on the south line of the Canadian National railway.The orebodies underlying the bed of Steeprock lake, since de-watered, were known to exist 60 years ago. References to the possibility of iron ore at this location were made in early geological papers and reports. In 1937 the locations of the orebodies were determined by dip-needle surveys, and from 1938 until 1943 diamond and churn drilling were carried on to prove their extent and configuration. It was found that the ore, in addition to being associated with definite types of wall-rock, was controlled by structural features, such as faulting and brecciation. From this geological knowledge the presence of other deposits has been inferred, and these are now being explored and developed.Production at the property commenced in October 1944. During that season 17,000 gross tons of ore was shipped. In 1945, 506,000 gross tons and in 1946, 830,000 gross tons was mined and shipped. In 1946, 164,000 gross tons additional was placed on stockpile for future shipment.TYPES OF 0REBODIES AND MINERALIZATIONThe orebodies at Steep Rock iron mine are tabular. They have an average width of 250 feet, lengths up to 5,000 feet, and persist to known depths of 1,200 feet. They are replacement deposits in brecciated carbonate rock at the contact of underlying pseudo-limestones and overlying volcanics. The ore is composed of hematite and hydrous hematite in the form of goethite, turgite, and limonite. These minerals replaced the brecciated host rocks metasomatically as a result of hydrothermal action. The replacement followed a definite structural pattern along the unconformable contact between the sediments or other rock (now replaced by carbonate) and the volcanics, subsequent to disturbances in the form of minor faulting and shearing. The faulting and shearing provided the channels through which the replacing solutions percolated. It is believed that the late basic intrusions outside the ore zones were genetically responsible for the introduction of the ore-bearing solutions."

Jan 1, 1954