Search Documents

By Candido Bariáin

A new vapochromic material of formula [Au2Ag2(C6F5)4(bipy)2]n (bipy = 2,2´ bipyridine) has been developed and used for the detection of some volatile organic compounds as acetone either in vapour or in water solution. The material is presented in the form of powders which colour changes with acetone vapours turning from bright yellow in the absence of vapour to white in the presence of vapour. By using the sol-gel technique, the powder ? dispersed in tetraethyl orthosilicate- was easily deposited on optical fibres. In order to study experimentally the behaviour of this material for construction practical optical fibre sensors, a sol-gel material doped with the vapochromic material is deposited onto an extreme of a monomode fibre connected to a coupler. The behaviour of the material was studied for different wavelengths and concentrations of acetone vapours and acetone/water solutions. Changes up to 4dB in the reflected optical power were detected. Optical fibre sensors have many advantages over conventional ones, such as electromagnetic interference immunity, passivity behaviour, possibility of using multiplexation techniques, low weigh and little size, etc. Actually, there is an increasing interest in developing optical fibre sensor for vapour detection in the chemical industry and in fact many sensor had been developed [1]. Some are based on the deposition of a sol-gel-based material either over the core of an optical fibre [1] or onto the thinner zone of a biconically tapered optical fibre [2]. Others are based on Fabry-Perot interferometers [3]. Also there are sensors based on the reflection of the light on films, on the fluorescence of dye-doped polymer cladding in fibre, on colorimetric reagents in the core of a silica fibre or on surface plasmon [4]. The possible materials for the construction of such sensor should be colorimetric reagents able to change the colour or refractive index in the presence of same organic vapours. There are not many metallic complexes with these properties, although same interesting examples have been reported in the chemistry of palladium and platinum as [Pt(p-R-C6H4NC)4][Pd(CN)4] described by Nagel [5] and Mann [6], which reported the construction of some LEDs. We recently reported the preparation of a novel vapochromic material (Fig 1) [7] which can be used for the construction of optical fibre tapered environmental sensors [8,9] of vapour organic compounds (VOC´s). Also we reported other nickel and palladium derivatives which present this type of behaviour [10]

Oct 1, 2003

By Li Qihou, Liu Zhihong, Liu Zhiyong, Yao Wei

Black copper sludge, which mainly contains copper, arsenic and a little antimony, bismuth, selenium, tellurium, is an important recyclable secondary resource. In this paper, selective removal of arsenic from black copper sludge by alkaline oxidative pressure leaching was studied. The influences of alkali concentration, leaching time, leaching temperature, oxygen pressure, liquid-solid ratio and other variables on the leaching rate of arsenic, copper and tellurium were investigated. The results were as follows: when the leaching process was conducted at initial alkali concentration of 1mol/L, liquid-solid ratio of 10, stirring rate of 500r/min, leaching temperature of 140°C for 5 h and oxygen pressure of 2.5MPa, the leaching rates of arsenic and tellurium were 85.43% and 59.7% respectively, and copper, antimony, bismuth were not leached. Hence, arsenic has been removed effectively from black copper sludge, while the valuable metals such as copper, antimony and bismuth remained in the residue that can be further recovered easily. INTRODUCTION Black copper sludge is a byproduct in the purification process of copper electrolyte. Arsenic, antimony and bismuth are major harmful impurities in copper electrolytic refining system. The accumulation of these impurities will cause adverse effects, such as the increase of electrolyte resistance and power consumption and deterioration of cathode copper quality (Wang, Liu, & Zhang, 2001). Hence, electrolyte purification is an essential part of the electrolysis process (Liang, Chen, & Guo, 2009). Electrolyte purification methods include electrowinning (Davenport, King, Schlesinger, & Biswas, 2002), solvent extraction (Navarro, Simpson, & Alguacil, 1999), ion exchange (Arroyo et al., 2017), coprecipitation (Wang et al., 2003, 2018; Xiao et al., 2007; Xiao, Cao, Mao, Shen, & Ren, 2014), activated carbon adsorption (Navarro & Alguacil, 2002), electrodialysis (Cifuentes et al., 2015), redox process (Zhou, Peng, Zheng, Ma, & Cui, 2011; Peng, Zheng, Zhou, & Chen, 2012; Zheng, Peng, Ke, & Chen, 2013), among which the electrowinning method is simple in operation and effective in impurities removal, making it the main process for current electrolyte purification. Some copper ions can react with harmful impurities to form complex black copper sludge by controlling the operation conditions of electrowinning process. Based on the estimated data provide by Davenport et al. (2002), an annual output of 400,000 tons cathode copper could produce 432-2168 tons of black copper sludge by electrowinning method. Black copper sludge contains 30~50% copper, 15~30% arsenic and a small amount of rare elements such as selenium and tellurium. Thus, recovery of valuable metals can bring huge economic interests. Moreover, arsenic in these sludges could cause significant environmental pollution. Therefore, effective removal of arsenic from these sludges is urgent and significant.

Jan 1, 2019

By Louise Corriveau

Exploration strategies have traditionally considered felsic gneiss complexes of the Canadian Shield sterile. This paradigm is challenged with the discovery of extensive granulite-facies Cu-Au, Fe oxides-bearing hydrothermal systems in the 1.4 Ga Bondy and 1.5 Ga La Romaine volcano-plutonic complexes of the Grenville Province. Early identification of magnetite-rich units in association with meta-exhalite and pelite-like units was key to targeting the search for mineralization, protolith information and indicators of pre-metamorphic hydrothermal activity during regional surveys of these frontier terrains. Textural evidences for a volcano-plutonic setting were found. There remained, however, numerous impediments to the recognition that the ubiquitous magnetite-laden units and associated aluminous gneiss were hydrothermal in origin. Many metamorphic reactions form magnetite at the amphibolite to granulite facies transition, and hydrothermally-leached rocks resemble metapelite or migmatitic restite, while carbonate alteration zones may look like marble or calc-silicate rock. Non-typical metamorphic mineral assemblages, modes and colours arise when hydrothermally-derived rock types are metamorphosed. These effective markers served as tools for reliable field identification of hydrothermally-altered rocks. In our case-studies, we traced pre-metamorphic hydrothermally-driven Fe-oxide precipitation in association with sericitization, albitization, pyrophyllite alteration, chloritization, and B enrichment by mapping unusually high contents of (1) magnetite or hematite, (2) biotite, (3) albite, (4) sillimanite, (5) orthopyroxene or phlogopite with cordierite, and (6) tourmaline or kornerupine. The unveiled garnetite, tourmalinite, and aluminous gneiss had assemblages that vary according to metamorphic grade and composition. To assess if high mode of Fe-Mg-Al phases resulted from partial melting (restitic residue) or metamorphism of hydrothermal rocks, we compared leucosome mineral assemblages, shape and amount with that expected of in situ partial melting reactions. In both areas there is no compelling evidence for these units to be restites. In contrast, the presence of lapilli in garnet-cordierite-sillimanite gneiss, though extremely rare, constitutes conclusive evidence for extreme pre-metamorphic high-sulphidation alteration of a volcanic protolith, while Fe-oxides or sillimanite-bearing nodules and veins record a less pervasive alteration. Geochemical research on element mobility and mass balance calculations further testified of an hydrothermal origin for these gneisses. The magnetite-rich units, together with calc-silicate rocks, garnetite, hornblendite, albitite among amphibolite, provided effective guides to sites of fluid discharge and led to the discovery of Cu and Cu-Au showings. With the presence of highsulphidation alteration, these features suggest early Cu-Au VHMS-type alteration halos within a predominantly felsic composite volcano-plutonic arc setting for both case-studies. Evidences for subsequent F-driven orthomagmatic fluid activity are also present.

May 1, 2003

By E. H. Hall

"Perhaps .I should start this talk on Arsine poisoning, by giving a brief background and history of the Bralorne Mill.The present Bralorne company started milling operations in 1932, with amalgamation and flotation, and operated continuously until 19 61 . In 19 59, it was decided to change over to cyanidation, and to use double filtration rather than counter current. The cyanide portion of this new plant was completed and went on stream in August 1961 utilizing the grinding circuit of the old flotation plant. The new grinding circuit was completed and started operating December 15, 1961.The grinding circuit consists of a 7 1 x 101 Hardinge Rod Mill, and a 7 1 x 101 Hardinge Ball Mill. In series with the rod mill is a 16"" x 24"" Denver Duplex Jig, and two of these jigs are also in parallel with the ball mill. The rod mill product is classified by a Kreb cyclone, the oversize going to the ball mill. The ball mill is in closed circuit with this same cyclone. The jig products are amalgamated daily, and the amalgam barrel tails are returned to the ball mill for regrind. Arsenious oxide (As203) is one of the reagents used in amalgamation. Approximately 39 ozs. per day is used.The cyanide circuit consists of a 481 x 121 thickener, three 24' x 24' agitators, two 141 x 161 drum filters and a Merrill Crowe precipitation unit.The Krebcone overflow is thickened to 60 - 62% solids. Hydrated lime, along with a settling agent is added to the thickener. Some of the overflow water from the thickener is returned for use in the jigs. The balance of this overflow water goes to waste. To the thickened pulp entering No. 1 agitator, barren solution is added, along with sodium cyanide and hydrated lime. Cyanide strength is held at 0. 9 - 1. 0 lbs/ ton solution and lime at 0. 8 lbs/ ton solution. The lime content usually drops to 0. 5 lbs/ ton in No. 3 agitator. The two drum filters are in series and are washed with barren solution. The discharge of No. 3 agitator is fed to No. 1 filter and the discharge of No. 1 filter is repulped in barren solution and feeds No. 2 filter. No. 2 filter discharges to tails, The filtrate is clarified, deaerated and the gold precipitated. One hundred to two hundred tons of barren solution are bled to waste each day. The ore contains 1 % Arsenopyrite and 1. 5% Pyrite."

Jan 1, 1964

By P. Tarassoff

Extractive metallurgy is concerned with the winning of metals from their ores and concentrates. It is therefore not unexpected that extractive metallurgy in Canada has always been closely linked with mining. The discovery and exploitation of new orebodies has provided the impetus for the building of many of our smelters and refineries - past and present - and for the development of new metal extraction processes. The purpose of this paper is to provide a brief overview of those early metallurgical developments, and to highlight the continuing expansion and diversification of the Canadian metallurgical industry.

Jan 1, 1999

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By V. A. Leão, M. L. M. Rodrigues, L. C. Sicupira, I. C. B. Rodrigues, T. C. Veloso

Brazilian sulphide ores can contain a significant content of chloride and fluoride, which are harmful to bacteria and thus bioleaching. This work summarizes a four-year research investigation on the effect of fluoride on both bacterial growth and sulphide bioleaching, supported by studies carried out with secondary copper ores. Firstly, the influence of fluoride on the kinetics of ferrous iron bio-oxidation with Sulfobacillus thermosulfidooxidans was addressed. Values as low as 10.0 mg/L F- fully inhibited bacterial growth, although fluoride toxicity could be overcome by the presence of aluminium, which reduced the concentration of hydrofluoric acid through the formation of aluminium-fluoride complexes. This required at least a 2:1 aluminium/fluoride molar ratio, which ensured bacterial growth rate values similar to that observed in the absence of fluoride ions. Subsequently, both batch and column bioleaching with mesofiles (30 ºC), moderate thermofile (50 ºC) or hyperthermophiles (67.5 ºC) of two secondary copper ore samples were analyzed with focus on the relevant effects of fluoride-containing minerals on the bioleaching of such sulphide ores.

Jan 1, 2014

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By Z. F. Lodhi, J. H. W. De Wit, H. A. Terry

Zinc and its alloys have been extensively used as replacements for Cadmium coatings in aeronautical and automobile industries. Zn alloys with low Co or Fe have been highly investigated but coatings with higher amount of Co are very difficult to achieve due to anomalism associated with these coatings. Anomalous Zn-Co-Fe alloy is a relatively recent addition to the family of Zn alloys. It is found that the addition of Fe in the electrolyte assist in overcoming the anomalism. In this research Zn-Co-Fe alloys especially with higher amount of Co (>15%) and Fe (~1%) are investigated, after overcoming the anomalism associated with its deposition, and the corrosion resistance is compared with pure Zn and Cd. It is found that an increase in Co to higher than 25 % accounts for a shift in the OCP to a level near Cd yet keeps it electronegative to steel. The coating shows superior corrosion resistance, in terms of its sacrificial and barrier properties in 3.5% NaC1 as compared to Zn and Cd.

Jan 1, 2006

By Edward Martinez

Laboratory studies had shown that the magnetite contained in serpentine asbestos ore was not uniformly distributed. Ore particles containing chrysotiye fiber responded to a magnetic f field; particles containing little or no chrysotile were essentially non-magnetic. Larger-scale tests, run with a magnetic pulley being fed various asbestos samples ranging in size from 1/4 inch to 5 inches, confirmed that magnetic separation could be used as a concentration step in an asbestos mill. Magnetic concentration was installed at the Black Lake and National mills of Lac d'Amiante du Quebec and has allowed the extraction of lower-grade ore, increasing the life of the mines. In addition, preconcentration early in the flowsheet increased the value of the feed to the fiber recovery section. An increase in fiber production was achieved, as well as a decrease in maintenance costs due to removal of flow-grade tailings early in the flowsheet. Magnetic concentration of a coarse tailings from the mill resulted in recovery of additional fiber previously discarded to tailings.

Jan 1, 1979

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007

By R. Bonnar, R. J. McH. Clark

"The Cheminis gold mineralization zone is approximately 6.5 km west of the Kerr Addison Mine along the Larder Lake Shear Zone, in the southern part of the Abitibi Greenstone Belt. The zone is very similar in appearance to the flow ore at the Kerr Addison Mine and occurs at the same stratigraphic position. Drilling has demonstrated that the gold mineralization at Cheminis persists to a depth of over 3000 ft .The mineralization is hosted by a pyritic, tuffaceous sediment which occurs within a sequence of volcanics and sediments which have been pervasively carbonatized. The gold is largely enclosed within pyrite grains and the amount of gold in the layers of pyrite increases in the layers closest to a graphitic f ault zone.It is suggested that the gold mineralization may be primarily related to the syngenetic sulphide concentrations formed during fumarolic activity on the seafloor along the Larder Lake Shear Zone. At a later stage a hydrothermal event associated with alkalic volcanism may have resulted in regional carbonatization and further concentration of the gold in the vicinity of fault zones."

Jan 1, 1987

By Greg Johnson

Maintenance needs information about assets to optimize availability and production needs information about performance and consumption to maximize output. In considering both these needs together as, ?Asset Optimization?, the information systems that support them are critical. The theory of Asset Optimization derives from the Lean Manufacturing concepts developed by Toyota, but some changes are required to apply this to mining operations. In particular, mining operations require automated systems due to their geographic spread and they need a strong emphasis on capturing under-performance losses as well as delays and stoppages in production. Leading metal miners and coal miners alike have applied these systems to good effect in the last 10 years. The concepts developed initially in minerals processing plants are now being applied to the mines themsleves as well as the mining logistics chain. Production increases of 5?10% are achievable with the right implementation and consideration of the some key lessons learnt in the last 10 years. Putting these lessons into action is one key step in the goal of optimizing asset performance and thus utilizing the resource at lowest cost.

Aug 1, 2013

By G. Gagnon

"HistoryMining of the Schefferville iron deposits began in 1954 on completion of the 357 mile railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at schefferville to develop a process for upgrading the extensive lower grade deposits containing 51% iron with 15% silica (natural analysis). Engineering for a six million ton per year beneficiation plant using cationic silica flotation and the A-C grate kiln Began in 1970 and the first pellets were produced in mid-1973.Production requirements and operating difficulties have restricted capacity to approximately 85% of design but on going improvements are being made continuously to attain design capacity.GeologyThe sedimentary ore bodies of the labrador trough occur in a belt 5 to 10 miles wide and 60 miles long and contain 51 individual deposits varying in size from 1 and 60 million tons. The ores are classified into three main color groups."

Jan 1, 1981

By Michel Carreau

Renewable assets have large upfront capital costs but minimal operating expenses over their lifetimes. In some instances, deals can be structured so that direct capital investment is feasible, with paybacks typically within 5-7 years. In others, the burden of renewable CAPEX must be removed in order to create an attractive alternative to fossil-fuel-fired generation. Hatch has designed and oversees the construction of a renewable installation, which is financed, owned and operated by a special-purpose entity. Renewable energy is then delivered to the mining company via a customized power purchase agreement at a price that is lower than the levelized cost of fossil fuels. In this way, the mining company removes the burden of the renewable energy CAPEX from its balance sheet, thus freeing up capital, decreasing risk, and making the predictable, lower cost of renewable power more attractive than the variable cost of fossil fuels. This paper presents the above business model and success stories of hybrid power at remote sites (wind and solar coupled with diesel engine).

Aug 1, 2013

By R. Therrien, L. Gosselin, J. Raymond

ABSTRACT: The ground-source heat pump is a low-carbon technology that uses the earth’s renewable geothermal energy to heat and cool buildings, with an ef?ciency 3 to 4.5 times that of conventional systems. These high performances are achieved by exchanging heat with the earth using a ?uid that is groundwater, surface water or closed loop water. Expensive installations, such as water wells or buriedcoils, are however necessary to transport the ?uid in and out of the earth, making ground-source heat pumps more costly than conventional systems. Installation costs can be reduced in mining environments due to the abundance and the accessibility of resources to be used with heat pumps. Examples of system design calculations using data from the Mouska and Doyon mines in Abitibi show signi?cant installation cost savings using dewatering mine water or ground heat exchangers installed below oxidizing waste rocks. Ground-source heat pump technology is reviewed and scoping calculations are presented to illustrate how such systems can be installed in mining environments.

Jan 1, 2010

By Robert S. G. Chapman, Kieran M. J. Downes

The Sulphide-Preview Lakes area is located 45 km northeast of La Ronge in northern Saskatchewan. It lies within the southern portion of the Proterozoic La Ronge Volcanic-Sedimentary Belt. Two styles of gold mineralization are present in the Sulphide Lake area , stratabound gold mineralization is intimately associated with a pyrite-pyrrhotite-arsenopyrite-bearing graphitic argillite unit within a sequence of intermediate to felsic volcaniclastics. Past operators established three mineralized zones along this horizon with combined reserves for two of the zones, of about 175,000 tons at 0.22 oz/ton Au. In the Preview Lake area , gold mineralization occurs in variably sheared gabbro/quartz diorite sills within a mixed sedimentary-felsic volcaniclastic sequence. Gold occurs with arsenopyrite, pyrite and minor chalcopyrite associated with quartz veins and stringers. A sulphidebearing graphitic argillite unit occurs in close proximity to the mineralized shears. Past operators delineated seven mineralized shear zones, two of which were drilltested. Average gold grades reported are in the 0.1 to 0.2 oz/ton range with erratic values up to 5.0 oz/ton.

Jan 1, 1986

By Gheorghe Vieru

Security and safety due to environmental impact as well as the radiological consequences during the uranium mining operations, tailings management, uranium processing, disposal of waste in conventional landfill sites are matters of great importance. The Uranium National Company (CNU) from Romania is responsible for all aspects belonging to the management of the entire Romanian uranium industry- the uranium ore extraction, transport and processing of uranium ore, concentrates processing, as well as disposal of sterile ore and waste. The paper will presents specific safety problems related to the identification and evaluation of potential environmental risks, as well as possible radiological consequences associated with the disposal of sterile and the uranium processing waste resulting from processing of the uranium ore. Computer codes will be used, such as IAEA INTERTRAN II and RADTRAN 5. It is also to be noted that this paper considers the main results of the scientific research carried out by the main author as CSI (Chief Scientific Investigator) for Romanian Research Contract on NORM concluded with IAEA Vienna.

Aug 1, 2010

By Amin Jafari

Macrosegregation has always been an important issue with the solidification processes, particularly in Direct-Chill Casting of Aluminum alloys, where uneven properties, surface and bulk defects and limitations in productivity can be arisen due to macrosegregation in the cast product. Following the global attempts to practically predict the macrosegregation, in the present work, a numerical model was developed based on an industrial scale DC casting process to simulate the solidification and macrosegregation in an Al-4.5%Cu billet. Interesting aspects of this investigation are concerned with an efficient numerical scheme to keep simplicity, consistency and desired physical resolution of the solidification phenomena together. In the mathematical model, coupled conservation equations of mass, momentum, energy and species were solved numerically using finite volume method. A different numerical scheme, called SIMTLE, was introduced to link the energy and species equations with the phase diagram of the alloy. Calculations were performed on an industrial case and obtained results were compared to available experimental data to assure the performance of the model. Different macrosegregation features were predicted and discussed on the solidifying Al-alloy billet.

Oct 1, 2011