Search Documents

By D. M. Baird

Copper mineralization occurs at several places along the shore of Notre Dame bay, Newfoundland, and at one time formed the basis of a considerable mining industry. The sources of the mineralizing solutions and the structural settings of some of the deposits have not been clearly understood. This paper reports new investigations into the origin and structure of the deposits between Bett's cove and Stocking harbour, in a strip about ten miles long and two miles wide along the western shore of Notre Dame bay. The most complete previous descriptions of the area are those of Snelgrove (1929, 1931, 1938), Douglas, Williams and Rove (1940), and the writer (1947). The discovery of the Bett's Cove deposits took place about 1860, soon after the discovery of the well-known Tilt Cove deposits to the north. Several other small prospects were found between Bett's cove and Stocking harbour between 1880 and 1910. At Bett's cove, active mining began in 1875 and a small smelting plant was built near the mine in 1877. .Mining operations came to an abrupt halt in 1883 after a major cave-in. In 1900, and again in 1906, attempts were made to drain the old workings and reopen the mine but were abandoned long before completion. Total production amounted to about 130,000 tons of hand-picked copper ore which averaged about ten per cent copper, and 2,450 tons of pyrite (Snelgrove, 1938, pp. 52-55).

Jan 1, 1948

By Julian Baldry

"This paper begins by describing the parameters of high-speed underground tracked drifting operations and the mucking cycle, and-discusses their variations. The railbound Haggloader 8HR is then described, as well as the Hagglund shuttle trains, outlining the advantages and disadvantages of the system. A comparison with conventional mucking operations is then given.IntroductionDrift and tunnel rounds are mucked by one of two major methods, either trackless with diesel loaders and trucks or with track loaders and cars. The aim of this paper is to compare the conventional tracked mucking cycle with the Hagglunds system alternatives.For many years, the traditional method of attacking the mucking cycle has been with a rocker shovel loader, a string of cars and a locomotive. The rocker shovel loads the first car and when full it is taken to a side drift, cherry picker or some other transfer point and is exchanged for an empty one. This empty car is then pushed back into the face and the loading continues until all cars are full . Then the whole train is taken out to a dump point where the cars are emptied. Normally the train's capacity is less than the volume of the muckpile, so the cars go back to the face. This loading cycle is repeated until all muck is removed from the heading. The last train out from the heading usually takes the loader and parks it in a side drift before continuing on to the dump where the cars are emptied.This simplified version of the traditional loading cycle excludes the ancillary work elements such as track laying and so on, but does point out that the cars must be transferred when full and that the whole train normally makes at least two round trips from the dump to the face. The prime aim in drifting is to cycle a round whithin a working shift which necessitates that no one part absorbs so much time as to prevent the completion of the cycle.Mucking, drilling and loading and the ancillary work such as rock bolting, vent and service pipe hanging typically each take one-third of the available work time. Drilling or mucking can and often do, because of various factors, take nearly half of the total cycle time. Once any segment of the operation starts to take this portion of the shift, the likelihood of missed rounds becomes increasingly greater."

Jan 1, 1981

By A. Mular, T. Bond, G. D. Farnell, J. F. Kingston

"ABSTRACT:-A 60—cm semiautogenous grinding-(SAG) mill was designed -for continuous wet operation in closed circuit with a vibrating screen. The circuit is fully instrumented and automated. Part of the control system incorporates Foxboro SPEC 200 controllers around the pump box to maintain level. The rest of the control system involves an ACTION model BC2 basic direct digital controller that handles all other inputs/outputs and contact closure sensing:·The success of the control system is attributed to the uniqueness of specially designed mass flow metering systems. Various control strategies are possible. Employed to date has been control of a mill load set-point by cascading the deviation from load set-point as the set-point to the fresh feed rate ""controller"". Mill feed water is ratioed to total flow rate of solids fed to the mill. The performance of the circuit is being correlated with the performance of full scale SAG circuits in British Columbia to develop models, to assess the feasibility of scale up and to investigate the effects of design variables on responses such as circuit throughput. 1 INTRODUCTIONWhere ore types are appropriate, semiautogenous grinding and/or autogenous grinding (AG) has replaced conventional grinding. Secondary/Tertiary crushing plants are thereby eliminated so that capital expenditures are less and overall comminution costs can be lower (Barratt 1982). To establish the suitability of an ore for SAG circuits, pilot scale tests with 1.7 to 1.8 M diameter mills are often conducted. At least one test per ore type in a deposit has been necessary. Often, each test involves a large amount (up to 50 tonne) of sample, so that the testwork can be expensive and may discourage the use of SAG or AG circuits. However, MacPherson (1977) has employed a continuous 45 cm dry Aerofall mill circuit closed with screens and an air classifier to determine whether ores are suitable for SAG milling. The amount of sample per ore type is of the order of 60 kg or less. Thus an established SAG mill scale up procedure that employs small circuits is highly desirable.The purpose of this paper is to describe a small 60 cm wet continuous SAG/ AG mill pilot circuit assembled at the University of British Columbia to study the feasibility of scale up, to assess the influence of design variables, to develop mathematical models and to evaluate the effects of alternative control strategies on circuit performance"

Jan 1, 1988

By A. V. Corlett

MR. C. S. Gibson: Mr. Chairman, I listened with much interest to Mr. Corlett's paper. Those of us who are directly engaged in mine ventilation and dust control are impressed by the improved atmospheric conditions to be derived from the use of methods of mining such as those in operation at Aldermac, which Mr. Corlett has just described, and those employed at Noranda. It is a well known fact that drilling-dust is one of the most potent factors in the production of silicosis in mines handling ores containing quartz, so that from that angle the use of diamond drills, instead of percussion drills, to drill ore for blasts in stopes is an important development. A second point which I think merits mention is blasting. Blasting, we all know, creates the most dust in a mine and the fact that you can drill ore for a large blast with diamond drills and fire it, say, on Saturday night, and then have all the next day to ventilate the workings, is a great advance in dust control. 1 have wondered if Mr. Corlett, or possibly those at Noranda, can en-vision the use of the diamond drill as a means of advancing cross-cuts and drifts, preparing stopes, etc. I believe it is a matter which is receiving considerable attention at the moment in some parts of the world and J thought it would be interesting to have Mr. Corlett's reaction on that point. MR. A. V. CORLETT: I am not quite so hopeful of using diamond drills as a means of drilling holes in the ordinary drift. Maybe some of the diamond drill men can give us some further information on that point. MR. R. D. LoNGYEAR: The diamond drill manufacturers are working on that problem, but until further work is done we have nothing definite to offer. Drilling holes with a diamond drill to compete with rock drills for advancing drifts and cross-cuts is a desirable objective, because of the elimination of drilling dust and the ability to cut a smooth bore of uniform diameter. To reach this objective, higher rates of penetration are required, which can only be achieved by discovering the optimum bit rotating speed, by reducing vibration, and by further improving the bits and machines. We are optimistic, but the problem is still largely in the research stage.

Jan 1, 1940

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By J. D. Galloways

The northern part of the P. G. E. railway traverses and opens up that part of the province known as the Cariboo district, comprising the Cariboo and Quesnel Mining Divisions, which are a part of the Northeastern Mineral Survey District. Williams lake, a divisional point on the P. G. E. is near the southern boundary of the Quesnel Division and from this point the railway runs northerly to Quesnel, its present terminus. From Quesnel the railway is projected and partially constructed to Prince George on the Canadian National railway; therefore its general trend is northerly through the heart of the Cariboo district. Early History There is no need to outline at any length the early history of mining in the Cariboo. It is sufficient to say that the great gold rush to the Cariboo, in the early sixties, was practically the commencement of mining in British Columbia. These early placer mining operations centred around the old towns of Quesnel Forks, Keithley Creek, Barkerville and Van Winkle, the latter now called Stanley. Many millions of dollars of placer gold have been taken out and the end of production is not in sight yet. The maximum yearly production was reached about 1863, after which there was a gradual decline in output. During the war years production was at a very low figure but a steady, even if small, increase has occurred in the last three years and prospects are encouraging for a much greater output.

Jan 1, 1925

By K. Fumimura, T. Nishimura, M. Kohno

When applying numerical techniques to problems of deformation of rocks, the body to be analyzed is divided into small portions and is represented by a system of points linked together with the neighboring points. In the so-called distinct element modeling, the particles in the system are directly connected by springs and a contact law is used to specify forces on the particles to simulate the mechanical behavior of the body. The relation between the spring stiffness and commonly measured material properties, such as the Young’s modulus and the Poisson’s ratio, should be known a priori. For the general case of a random packing of particles, the relation is found by means of a process in which a system of particles and set of parameters are prepared to simulate a set of specimen-size test and then the input parameters are chosen to match the measured material properties. The validity of the numerical result is only demonstrated by comparison model behaviors with the measured responses. The process includes trial-and-error manner, therefore, no model is complete to reproduce the mechanical properties. In this paper, a relation between the spring stiffness and the elastic constants; the Young’s modulus and the Poisson’s ratio, is introduced to a three-dimensional distinct lattice spring method. Two simple numerical examples will be presented to demonstrate the performance of the method with the procedure for the determination of the spring stiffness.

Jan 1, 2015

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

By J. E. Tupper

"This paper will discuss strategies for the introduction of computer technology in the mine environment. More specifically, it will focus on issues such as: (a) make or buy; (b) programmer less mines; and (c) support from corporate groups.The paper relates these strategies to systems for mine operations. These will be illustrated by considering the implementation of some phases of these systems at Teck Corporation.IntroductionThis presentation addresses some of the major considerations in a strategy for mine computerization and then relates these considerations to the computerization cycle and Teck Corporation.Strategy is defined as a conceptual framework or plan to accomplish a goal. For purposes of this paper, the goals can be more simply defined for operational purposes as either increasing revenue or decreasing costs.The strategy will allow us the framework for measuring tactical decisions such as computer and software acquisitions.The Mine Life CycleTo start with, let us look at the mine life cycle from a computer systems point of view:-Exploration-Property Development-Feasibility-Construction-OperationFrom a systems point of view, the exploration cycle is oriented to geophysical and geochemical computing. Property development starts with drilling and building the geological data base. The feasibility cycle includes all stages of evaluating the decision to proceed with mine development: ore reserve calculations; mine planning; and financial projections. Construction includes project management and project accounting systems. Systems required for operation are those needed by personnel at the mine site."

Jan 1, 1982

By Murray W. Grabinsky

The in situ performance of Cemented Paste Backfill (CPB) systems can be monitored to improve understanding of the paste?s behaviour and therefore optimize the geomechanical design of the cemented paste backfill system (i.e., minimize binder content, minimize fill barricade complexity, maximize fill rate-of-rise during backfilling, and minimize cure time before resuming production blasting in proximity). However, undertaking such a monitoring program is inherently complex, because the rate-of-rise and accompanying self-weight induced stresses occur at a time rate that is similar to the rate of hydration and associated increase in the paste?s stiffness and strength. In addition, arching within the stope complicates the overall stress distribution. Therefore, to obtain a complete picture of the CPB?s response, it is necessary to measure several variables (3-D total pressures, water pressures and suctions, hydration rates, and blasting induced vibrations) at a given ?point?, and take all such measurements at many points throughout the fill mass as well as at barricade locations. The overall testing program can therefore be logistically difficult to implement and have an apparent high cost. However, if the program is successful, the benefits arising from improved mine design can significantly outweigh the seemingly high initial capital and labour costs of the monitoring program. A case study involving an instrumented paste fill in a tall and narrow Alimak stope is briefly outlined. Plans for a similar experiment in a large long-hole stope are then considered.

May 1, 2008

By Gulshan Kumar Pradhan, Yogendra Pratap Singh, Dhawanm Nikhil

"Potassium (K) is one of the essential elements for the growth of plants and thereby for humans. In fertilizers, potash demand has been steadily increasing at ~3.5% annually. Water soluble potash deposits are rare and highly localized. India is neither present on the world potash production map nor it has adequate potash rich rocks. The K-bearing minerals are recovered either by using conventional underground mining methods or though solution mining methods. India possesses a vast resource of silicate rocks such as glauconitic sandstone and Feldspar. These rocks are basically a group of alumino silicate of potassium, sodium and calcium (K2O%: 5-12, Na2O%: 3-10%, SiO2%: 52-65, Al2O3%: 15-20, Fe2O3%:, 5-7 and MgO%: 2-3.5).The K extraction from silicate rocks has received little attention probably due to the slow release, the locked structure of alumina-silicate minerals, and the unavailability of appropriate economic processes & their know-how. In fact due to this India imports all of its potash demand (about 3.5 million tons per annum) from different countries.In the present work, an attempt has been made to identify the structural and chemical alteration of desired K mineral phase in silicate rock (~K2O%: 10.5, Na2O%: 2%, SiO2%: 55, Al2O3%: 19, Fe2O3%, 5-6, MgO%: 2.5) under different conditions such as acid leaching, thermal treatment and chemical processing. Different treatments are aimed to increase K availability which is related to the modifications in mineralogical composition. The modifications in the feed sample and treated samples are studied through SEM-EDAX, XRD, EPMA and optical microscope. With the combination of treatments, it is possible to extract more than 90% K and the formation of sylvite phase (water soluble) confirms the dissolution of potash values."

Jan 1, 2016

By P. E. Georghiou, S. Shafiei Zadeh, H. Hassan Nejad

Data are presented on the extractant behaviour on toxic metal removal from spent hydroprocessing catalyst, produced at the North Atlantic Refinery plant in Newfoundland and Labrador. Aliquat 336 was selected due to its potential capabilities for the separation of cobalt, molybdenum and nickel from the leachate extractant produced by aqua regia. The solvent extraction process was statistically modeled using central composite design (CCD), and the numerical optimization was conducted to achieve the optimum point for toxic metal recovery for the extractant.

Jan 1, 2014

Red Chris Project Project Status ? Tahltan, Iskut First Nations MOU ? Bankable Feasibility Study ? BC Environmental Assessment Certificate ? CEAA (Federal Environmental) ? EPCM contracts LOI?s ? US$110 million Project Debt Financing(credit approval pending) ? 1st5 years concentrate production sold ? 99,150 m of drilling in 371 holes First Nations Participation Agreement ?Advanced stage negotiations

May 1, 2006

By M. Nagamori, A. J. Plumpton

"A low-grade concentrate from the Crevier Township, Quebec, containing 1.8% Ta205 and 13.7% Nb205 was reduced with carbon at 1600°C, and niobium and tantalum were selectively absorbed in liquid iron. To slag off the zirconia-rich gangue, some silica and lime were added as flux. Metallic iron was added in such a way that the combined contents of TaC and NbC did not exceed 20% in the ferroalloy . Up to 95% of the niobium, and up to 80% of the tantalum contained in the concentrate were recovered in the metal. The ferroalloy was ground finely and dissolved in 2 wt % sulphuric acid to leach out iron and silicon preferentially. The insoluble residue consisted principally of NbC and TaC, the calcination of which yielded an enriched concentrate comprising 80% Nb2O5 and 8% Ta2O5. The insoluble residue could also be chlorinated to obtain an impure liquid of Nb2Cl5 and TaCl5. Process variables and their effects are discussed in terms of higher metal recoveries in the smelting.IntroductionPresently, about one-third of the world production of tantalum comes from the pyrometallurgical reprocessing of tin slag, a by-product of tin smelting, containing sometimes 2 to 10% Ta205 and about the same amount of Nb205. Upon heating tin slags with carbon at about 1600°C in an electric furnace, tantalum and niobium oxides are converted to TaC and NbC, which are absorbed by the coexisting phase of molten metallic iron(1,2). The Fe-Nb-Ta-C melts cannot be decarburized by oxidation because of the preferential formation of Nb and Ta oxides over CO gas(3). So, the ferroalloys containing tantalum and niobium carbides are commercially treated by acid-leaching and I or chlorination to eliminate iron and thus permitting the eventual recovery of purified tantalum and niobium oxides(2).Absorbing Ta and Nb carbides in molten iron was first proposed and demonstrated by Zimmerley and Back(4) in 1957 in order to recover selectively tantalum and niobium from lowgrade concentrates. The process was successfully applied to the electric furnace smelting of tin slags by Hunter and Fursmant(5) over a period preceding 1965."

Jan 1, 1985

By E. Ghali, W. Zhang, C. Su, N. Sorour, G. Houlachi

"Zinc electrowinning process is sensitive to the presence of metallic impurities such as lead ions that could substantially and negatively affect the power consumption and surface morphology. Effect of various concentrations of manganese ions and traces of lead ions up to 2.5 mg L-1 added to the electrolyte during electrowinning have been investigated by electrochemical polarization techniques such as galvanostatic, cyclic voltammetry and potentiodynamic. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were applied to examine the surface morphology and crystallographic orientation, respectively. Microwave plasma-atomic emission spectrometry has been used to determine the lead content in the deposit and in the electrolyte after electrodeposition. It was found that lead ions added to the zinc electrolyte led to the increase of cathodic overpotential and current efficiencies of zinc deposit. However, addition of Mn2+ into the zinc electrolyte resulted in the decrease of cathodic potential and current efficiency of zinc deposit. It can be stated as example that galvanostatic polarisation at 40?C and 52.5 mA cm-2 in presence of lead up to 0.1-0.2 mg L-1 in the electrolyte and 8-12 g L-1 Mn could be better considered as practical working parameters for electrowinning process.INTRODUCTIONApproximately 85% of the global production of zinc metal is produced by electrolytic process (Sinclair, 2005). The main goal of the zinc plant is to obtain pure zinc deposits with high current efficiencies. Smooth and pure deposits with high current efficiency (CE) are always obtained from pure electrolytes (Alfantazi & Dreisinger, 2001). The presence of metallic impurities in the zinc sulphate electrolyte is a major problem for the zinc electrowinning industry, since decreases in current efficiency, changes in deposit morphology and cathodic polarization are observed for electrolytes containing small concentrations of impurities (Ault & Frazer, 1988; Muresan, Maurin, Oniciu & Gaga, 1996). Low level concentrations as parts per million of these impurities are reported to influence negatively the zinc electrodeposition (Beshore, Flori, Schade & O'Keefe, 1987)."

Jan 1, 2016

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By Q. Han

Irradiation of high energy ultrasonic vibration in metals and alloys generates oscillating strain and stress fields in solids, and introduces nonlinear effects such as cavitation, acoustic streaming, and radiation pressure in molten materials. These nonlinear effects can be utilized to assist conventional material processing processes. This article describes recent research at Oak Ridge National Labs (ORNL) and Purdue University on using high intensity ultrasonic vibrations for degassing molten aluminum, processing particulate reinforced metal matrix composites, refining metals and alloys during solidification process, welding, and producing bulk nanostructures in solid metals and alloys.

Jan 1, 2014

By J. B. Heslop, D. S. Bubar

"The Gondor Zn-Ag-Pb-Cu deposit is a stratabound massive sulphide lens occurring within Archean volcaniclastic rocks of the Yellowknife Supergroup. The deposit is located in the west-central portion of the Slave Structural Province, approximately 350 km north of Yellowknife.Initial diamond drilling at Gondor has outlined a steeply dipping, L-shaped, folded, massive sulphide body, which may be traced over a strike length of approximately 800 m, and to a depth of 350 m. True widths of up to 40 m have been intersected in the thickest part of the deposit. Preliminary estimates suggest that the deposit contains a minimum of 7.5 million tonnes grading 6% Zn, 50 g/tonne Ag and less than I% combined Cu and Pb. In addition, significant gold, grading up to 2.8 g/tonne, occurs in some parts of the deposit. The mineralization is open both down-dip and along strike.The Gondor deposit lies conformably within a predominantly east-west striking, north-facing sequence of felsic to intermediate volcaniclastic rocks. Coarse fragmental rocks are abundant in the hanging wall, whereas ash and lapilli-tuffs predominate in the footwall. The main structural feature in the area is a large-scale, steeply northeast-plunging, Z-shaped fold. The sulphide mineralization lies within the synformal portion of this fold, with the thickest part of the deposit coinciding with its hinge zone. Several episodes of faulting have also affected the local stratigraphy.The wallrocks of the Gondor deposit were hydrothermally altered prior to the onset of medium-grade regional metamorphism. A halo of altered rocks surrounds the massive sulphide lens, with no apparent difference in the degree of alteration between the hanging wall and footwall strata. The alteration zone is characterized by the addition of MgO and K20 and by the depletion of Na20 and CaO. These changes are reflected in the mineralogy of the altered wallrocks by local enrichment in chlorite, biotite, muscovite and cordierite.The mineralized zone is medium- to coarse-grained, well-banded and is composed largely of pyrite, quartz, and sphalerite with subordinate galena and chalcopyrite. Preliminary studies of metal distribution indicate that a lateral zonation is present, with lead enrichment in the central part of the deposit, and copper enrichment toward both ends. Stringer-type copper mineralization has not yet been discovered in the footwall of the Gondor deposit."

Jan 1, 1985