Search Documents

By E. R. Mitchell

When we grow up in an urban environment and choose to become a part of a way of life, it is sometimes difficult to appreciate the cost of this decision in terms of pollution. Explained in this article is our dependence on technology and the amount of pollution that technology produces. Inventories of air pollution on both a personal and a national basis are given so that the reader may judge the magnitude of the problem. In doing so, it is hoped that the reader will understand the need for a responsible attitude toward pollution by everyone and how he can make a personal contribution.

Jan 1, 1971

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By Luino Jr. Dell'osso, Richard L. Every

The enormity of the methane-in-coal problem is discussed, with a brief summary of the state-of-the-art. Laboratory techniques and data on the desorption of methane from Pittsburgh seam coal are presented and discussed and include the effect of time, temperature and vacuum. Under laboratory conditions, it was possible to displace 90 per cent of the residual methane by flooding the coal samples with carbon dioxide. Carbon dioxide was found to be three times more effective than air and almost five times more effective than helium.

Jan 1, 1972

By K. Soldenhoff, D. Wilkins, E. Ho

In the processing of rare earth ores, a pure, mixed rare earth chloride solution is usually produced and used as the feed to solvent extraction circuits to separate the individual rare earths. Cerium(III) may be separated from the other rare earths by oxidising it to cerium(IV), which precipitates as cerium(IV) hydroxide in chloride liquors. This oxidation step may be inserted either before rare earth separation by solvent extraction or between solvent extraction circuits. Although oxidation of cerium by sodium hypochlorite has been known for many years, detailed conditions for oxidation are not readily available. The effect of hypochlorite addition, temperature, pH and cerium concentration on oxidation of cerium(III) from synthetic solutions was investigated

Jan 1, 2014

By M. Vaillé, B. Bossé, N. Durupt, A. Michaut

Imouraren is a sedimentary uranium deposit (> 150,000 tU @ 800 ppm), located approximately 100 km North-Northwest of Agadez (Niger); its depth reaches 110 to 170 meters. For low-grades ores, heap leaching is commonly considered as the appropriate technology for metal recovery. More precisely, the ore is crushed (≤ 300 mm) and agglomerated before being stacked. In this case, sulfuric acid can be added during agglomeration and/or irrigation (for three months to a year) to improve uranium recovery. It is known that mineralogical, chemical and physical properties of the uranium ore impact recovery, yet many challenges remain to increase recovery using this process. For example, ore heterogeneity and spatial variability (e.g., variation in uranium, carbonate and/or clay contents) can affect heap leaching performances (i.e., metal recovery, acid consumption or neutralization, percolation rate). However, laboratory column tests using composite ore sample that do not consider ore heterogeneity are widely used to anticipate recovery. Consequently, a new approach that consists in using Imouraren drill core ore samples was recently investigated. This latter also enabled a better assessment of the main parameters that influence uranium recovery and proposed a new predictive model to optimize mining operations.

Jan 1, 2020

By G. Zárate, G. Tapia

Anglo American Chile has been doing copper concentrate leaching studies at the laboratory and small pilot plant scale since 1992. Among the processes evaluated are bacterial leaching and pressure leaching using Mantos Blancos, Salobo Project and Quellaveco Project concentrates. Late in the nineties, it was decided to focus the research on pressure leaching, either medium or total pressure oxidation. Preliminary scouting tests were run with Mantos Blancos concentrate samples during 2000, which were repeated during 2003 together with samples of Los Bronces and El Soldado concentrates, in order to define the most suitable concentrate for running a pilot plant campaign at AARL, which was carried out in two campaigns, a first one from November 2003 through January 2004 and a second one during April 2004. Mantos Blancos was the selected concentrate and the laboratory and pilot plant results are discussed in this paper together with some preliminary economic estimates.

Jan 1, 2004

By R. Stauber, B. Friedrich, S. Hilgendorf, G. Homm, C. Gellermann

Due to recent regulations limiting tolerated lead concentrations in copper alloys, new recycling strategies have to be considered. This study investigates the suitability of technical approaches in order to recycle leaded copper alloys exemplified by CuZn39Pb2 and produce an alloy in compliance with future lead regulations in the European Union. Three pyrometallurgical methods are considered to achieve this goal, namely vacuum distillation, intermetallic precipitation and fractional crystallisation. The impact of essential process parameters i.e. pressure, temperature, time, atmosphere and quantity of additives are identified using thermochemical and kinetic modelling. An experimental implementation reveals a general suitability of all three refining processes. However, the individual efficiency of the different methods strongly differs. Thus, a detailed assessment is carried out in order to provide an evaluation on the efficiencies of these methods from a technological, economical and environmental point of view. Taking a possible industrial realisation into account, the authors recommend the approach of vacuum distillation, although the energy demanded is comparatively high due to the enthalpy of evaporation for zinc, or rather, lead. However, required lead concentrations can be reached quickly without introducing an external element to the material. The prediction of selectivity and evaporation speed, which are immanent variables for a successful implementation, can be validated experimentally. INTRODUCTION In 2016 approximately 1 million tonnes of leaded copper alloy semi-finished goods with an average lead content of 2.1 Ma% have been produced in the European Union (EU). The global production in the same period exceeded 5.5 million tonnes, while the lead concentration has stayed constant at around 2.4 Ma% for the last 50 years. Up to 80 % of the current production volume is covered with end-of-life scraps, which are used for direct re-melting, depending on the alloy composition. Lead has been a popular alloying element in copper alloys in general, and in particular in brass due to its positive impact on various mechanical, physical and chemical properties, especially machinability. Health and environmental concerns were drivers for many governments to implement limitations on lead. In order to further utilise the resource potential of leaded copper scrap, it is inevitable to develop methods to efficiently eliminate lead from circulation as far as possible. (Glöser, Soulier, & Tercero Espinoza, 2013; Soulier, Glöser-Chahoud, Goldmann & Tercero Espinoza, 2018)

Jan 1, 2019

By J. C. Mitcheson

Mr. President, Mr. Mayor, Ladies & Gentlemen: IT GIVES ME great pleasure to have the opportunity, today, to speak on behalf of all the constituent. bodies of the Common-wealth Council of Mining and Metallurgical Institutions. For the past month we delegates have been right royally entertained across the length and breadth of Canada by Provincial Governments, City Councils, and other equally generous public organizations and private corporations. On this occasion, however, the President of The Canadian Institute of Mining and Metallurgy, our good friend Dr. H. J. Fraser, has been our host at the enjoyable reception preceding this Institute Luncheon, which luncheon was sponsored by our official host, The Canadian Institute of Mining and Metallurgy, one of our .constituent bodies.

Jan 1, 1957

By Thomas Genty, Pascal Marcotte, Matthew Gillman, John Baechler

Elevated concentrations of ammonia nitrogen is a common characteristic of mine impacted water and generally results from the dissolution of undetonated explosives (i.e., Ammonium Nitrate and Fuel Oil and emulsion explosives) by contact water. Several active water treatment technologies are commercially available to remove ammonia nitrogen, but reduction of active treatment demand by promoting natural attenuation is considered best industry practice. In this paper, the results of laboratory-scale and full-scale trials of a semi-passive approach (i.e., enhanced algae growth) to remove ammonia nitrogen at the Meliadine mine are presented. Phosphorus was found to be the limiting factor to algae growth at the mine site. The addition of various concentrations of phosphorus was first tested at a laboratory scale. The samples were exposed to in-situ conditions, and ammonia nitrogen removal rates ranging from 40% to 93% were achieved over a period of 24 days. This paper also presents the methodology and results of an in-pond treatment during which a 50% ammonia nitrogen removal rate was observed after 68 days. The studied mine site uses breakpoint chlorination as its primary treatment approach for ammonia nitrogen removal. The results presented in this paper show the potential of using enhanced algae growth as a pre-treatment method, subsequently reducing the quantity of chemicals required for operating the breakpoint chlorination plant. This potential requires further investigation and additional trials are currently under evaluation.

Jan 1, 2023

By Jürgen Kretschmann

The Islamic Republic of Iran is a very important producer of raw materials in the world. The country holds 68 types of minerals, including salt, sand and gravel, chrome, lead, zinc, copper, coal, gold, and iron-ore. With more than 37 billion tons of measured and indicated reserves and 55 billion tons of total mineral resources, Iran is ranked among the 15 major mineral-rich countries. Sangan iron-ore mines (SIOM) is one of the biggest iron ore mining complexes in Iran, located in a remote, but strategically important area near the Afghanistan border. The Iranian government has planned several mining projects in this region for a stepwise development over the next 5 years to satisfy the growing demand of the Iranian steel industry. In cooperation with private companies, these projects shall be realized as sustainable as possible. This paper introduces SIOM and describes socially responsible activities undertaken during the initial development of this mining complex. The effects of these activities will be demonstrated. Unique attributes of the Sangan area have a significant impact on the acceptance of SIOM by regional stakeholders. The government has made several social investments that benefit workers´ families and the community. They are attempts to build social capital for the mining operations and demonstrate a commitment for socially responsible mining to the communities and the local population. They aim to create a balance between the local and regional expectations and requirements and the necessity to secure the corporate profitability at a reasonable and sustainable level. Investment in socially responsible activities is not a choice but a necessity to improve the relations between mining companies and stakeholders in the communities. It is recommended that social investments should be carefully planned and implemented from the early stages of mining activities, and should proceed throughout the life cycle of the mines.

Aug 1, 2013

By Karl J. C. Harries

"The Table of Contents that follows is only an example and is the Table of Contents from an actual negotiated agreement. It is merely intended to show how an agreement might be set out and the nature of possible provisions. As a negotiated agreement the format was dictated by the negotiations. It is not offered as a precedent of what should be contained in a joint venture agreement (“JVA”), the “proper” sequence of Articles, or a complete listing of the contents of joint venture agreements generally. The set-up used for an agreement should be decided by the parties and be one they consider flows in a logical and workable sequence. This example sets out the “deal” first, followed by the provisions relating to how work is to be carried out and then by administrative provisions necessary to make the agreement work. If you are more comfortable with, say, having the Committee provisions at the beginning, by all means have it drafted that way -- you are going to have to live with the agreement and work under it.Notes:1. The Table of Contents provisions appear in bold print. The italicized sections are annotations, which have been provided in some cases where the heading may not clearly describe the contents. They are not intended to be comprehensive, but refer to some specific matters that are considered to be of interest or to need some clarification.2. The subject matter of many of the articles and paragraphs is discussed or commented upon in the text of the book. Some of section cross-references have been provided. Such references are only to sections where the topic is a principal subject and no attempt has been made to provide a comprehensive indexing.3. Although this particular agreement is a three-party agreement, *B* and *C*, the Owners, are required to act as a unit (see para. 1.09. – § 8.44.), making the agreement effectively a two-party agreement. The parties insisted upon having a decision-making Committee and structuring the agreement accordingly. As is explained in § 8.11., such an arrangement is not recommended and can result in problems.5. See also §§ 8.24., 8.41. and 14.13. for discussions on tables of contents, summaries, and headings."

Jan 1, 2003

CSIRO Minerals, in association with the AJ Parker CRC for Hydrometallurgy, has an active program of hydrometallurgical research in which physical and computational modelling are used to better understand and improve a range of different unit operations. The modelling is based on flow simulation (Computational Fluid Dynamics or CFD), but incorporates other physical and chemical phenomena of importance, such as droplet break-up and coalescence, species transport and reaction. This paper reviews some of the major projects that have been undertaken at CSIRO Minerals and will illustrate the critical importance of hydrodynamics to the performance of unit operations and the improvements that can be made to performance using such modelling techniques. Unit operations that are discussed include solvent-extraction, gravity thickeners, flotation cells, bio-heap leaching and stirred tanks.

Jan 1, 2005

By Champoux. G., E. Ghali, W. Zhang, G. Monteith, A. -M. Lafront, G. Houlachi

The efficiency of the electrowinning process of zinc depends on the performance of oxygen evolution reaction, anode quality and corrosion resistance of lead anodes. Original surfaces of rolled commercial lead-silver anodes were examined using conventional polarisation methods in acid zinc sulfate electrolyte with manganese sulphate at 38 °C. The self-discharge method (potential decay) following 5 h polarisation at 50 mA cm-2 was considered to evaluate electrochemical activity, oxygen overpotential and anode stability. The influence of silver content is compared to that of the microstructure, the fabrication process and the composition of the corrosion products. Polished anode samples have also been examined for microstructural and corrosion performance studies. The experiments show that the duration of the plateau at 1600 mV versus SHE, the potential level (active corrosion state/stationary state) and the rate AEco/At during the decay could be a good indicator to compare the corrosion rates of the anodes in industrial zinc electrolytes.

Jan 1, 2008

By W. Hunka

PACIFIC PETROLEUMS, Ltd. first discovered commercial quantities of gas in the Peace River area in 1952. Development of gas wells in this area is quite ex-pensive due to low penetration rates. To improve the economics, the potential of the wells in many cases had to be increased. At that time, well stimulation was still in its infancy in Canada and in this area, in particular, no treatment of any consequence had been attempted. Therefore, trial-and-error was the only means available to determine the stimulating technique that would give optimum results. Various fluid treatments were available and these were used wherever the application was warrant-ed. This paper covers acid fracture and explosive treatments as carried out on various gas-bearing horizons.

Jan 1, 1958

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

By Hector Monette

"AFTER SPENDING a lifetime in the mining industry it is normal that one should be concerned with the future of his profession, especially if he is directly responsible for the education and formation of future mining engineers. It is not necessary to insist on the importance of mining for Canada and for the entire world to prove the necessity of the Mining Engineer. A statement was made by Zay Jeffries, former vicepresident of General Electric Co., and here I quote: ""Even though minerals without man are of no moment, man would not be man as we know him without minerals ... ""minerals are as essential to the life of social man as food is to man himself"". This certainly expresses magnificently the purpose of the mining profession. These are the reasons why I have accepted to present my views on the future of the Mining Engineer. If I express some concern it is not because I feel that there is any danger for the profession to disappear; men will always respond to a challenge and this can be found in the extraction of minerals as well as in any other field of human endeavour. However, the first big question concerns the competitive position of Canada in the world of mining. To be made available to Canadians and to the rest of the world, all this tremendous potential mineral wealth that our country has been so generously endowed with by nature must be gained from the earth's crust at a competitive cost. Otherwise it will never become ore and will have no value. Let us not forget that although minerals are discovered, mines are not found but are made. So let us be more efficient mine makers. To accomplish this end, it is the duty of the different responsible organizations at all levels - be they governmental, para-governmental, public or private institutions - to do their utmost to assure the profitable development of our mineral wealth. The University has an all-important role to play in preparing all the specialists required by this intricate machine that mining is. All the different disciplines of engineering, health, social and -managerial sciences are needed for the good functioning of the mining industry. Although they are all essential, some will play a more important role as a member of the structure. In this discussion it is the role of the most important member, the mining engineer, who is actually responsible for the extraction of the minerals from the earth's crust that must be established. From this we will then be able to analyse his responsibilities and try to suggest the mining engineering program most suitable to prepare this engineer for his future role."

Jan 1, 1972

By Daniel Murray

"ACCIDENT PREVENTION in and around coal mines presents many problems of a type which are not encountered in any other industry. This is particularly true of the coal mines in Nova Scotia, where the underground workings are very extensive and the area of exposure to workmen is very great.Roof conditions at the coal faces and in the waste change very rapidly, almost from hour to hour, and it is at these places that the greatest dangers exist and where most mine accidents occur. It is only natural, therefore, that our attention, as far as accident prevention is concerned, should be concentrated •at the coal faces and in the waste, especially in mines where the longwall system is used in the operation •of the seam.It has been said that no hard and fast rules can be set down for timbering at the coal faces and in the waste in the coal mines in this area. We do not subscribe to this theory, however, for the following reasons:On the longwall faces in No. 18 Colliery of the Dominion Coal Company, Limited, where the 'Dosco Miner' has been in operation and where there is a very rigid system of timbering and roof supports, which is strictly followed, only one compensable accident has occurred on those faces from May 2ndJ 1950, to the time of writing this paper, February 3rd, 1953.The 'Dosco Miner' has worked on four different longwall faces in this mine and has mined and loaded some hundreds of thousands of tons of coal."

Jan 1, 1953

By R. C. Gilmore, J. F. Brune

"Pulverized limestone rock dust used in United States underground coal mines to prevent and suppress coal dust explosions must easily disperse by forces of a methane or coal dust explosion. Moisture in the mine environment causes caking of the dust. Colorado School of Mines researchers performed dispersibility tests in a full-size explosion test drift. Tests included conventional, hydrophobized, and rock dust approved for German mines. Conventional and German standard rock dust products partially agglomerate, which may not be effective in suppressing a coal dust explosion, while hydrophobic rock dust retains better dispersibility.INTRODUCTIONA coal dust explosion devastated the Upper Big Branch mine in 2010 resulting in the death of 29 miners, the worst mining accident in the United States since 1972. The explosion propagated through approximately 65 km of active mine workings, but was extinguished in areas that had been properly rock dusted (Page, 2011). Researchers have long studied and established the ability of inert limestone rock dust to suppress coal dust explosions, see Richmond et al. (1975), Cybulski (1975), and Sapko et al. (2000).To be effective, rock dust must contribute to a total inert content of > 80% by weight and 100% of rock dust particles must pass through an 850 µm sieve, while 70% of the rock dust must be finer than 74 µm. This is established in US regulations 30 CFR §75.2. Dry rock dust is a nuisance that prevents mining work downwind from rock dusting activities. To overcome this problem, dust manufacturers have proposed applying the rock dust as a wet slurry or foam. After drying, manufacturers expected the slurry or foam-applied dust to have the same explosion suppression capabilities as dry-applied rock dust.Researchers at the Colorado School of Mines (CSM) designed and built a full-scale, underground Explosion Test Facility (ETF) at the CSM Edgar Experimental Mine in Idaho Springs, Colorado about 20 miles west of the CSM Golden, Colorado campus. To disperse the different rock dust products, researchers produced an air pressure pulse using a mesh array of PETN detonation cord. This method is simpler, more reproducible and safer than other methods considered, including methane-air explosions and a compressed air cannon. The detonation cord blasts produce a wind velocity of 30 to 50 m/s, the minimum velocity at which coal dust explosions can propagate, based on research by Nagy (1981) and Cybulski (1975)."

Jan 1, 2019

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005