Search Documents

By Olav Mejia

The rising energy costs and environmental considerations in mining necessitate the development of energy-efficient copper and gold processing plants. This paper presents an analysis of technical strategies aimed at reducing energy consumption in these plants. Key approaches include the integration of advanced ore sorting technologies, High Pressure Grinding Rolls (HPGR), Coarse Particle Flotation (CPF), and high-intensity flotation. Ore sorting enables early-stage waste removal, reducing the downstream processing load and associated energy use. HPGR technology, recognized for its energy efficiency, contributes to significant energy savings in comminution circuits by reducing reliance on traditional grinding methods. CPF technology further optimizes flotation performance by enabling the recovery of larger particles, thereby decreasing the need for fine grinding and reducing overall power demand. High-intensity flotation units enhance separation efficiency and mineral recovery in a compact footprint, offering further reductions in energy consumption. Together, these technologies provide energy saving opportunities to achieve a more sustainable and economically viable processing operation. This paper evaluates the effectiveness of each method, highlighting their potential impacts on energy consumption, operational efficiency, and cost-effectiveness in copper and gold processing

May 4, 2025

By W. Dingley, G. R. Hoey

"AbstractWear of six types of grinding balls was compared with and without corrosion inhibition in grinding Ni-Cu sulphide and hematite ores in laboratory ball mills. Forged steel balls (Rc 60 to 65) and three types of white cast iron balls (Rc 50 to 65) were susceptible to corrosive wear and two types of stainless steel balls [AISI Type 440C (Rc 65) and AISI Type 302 is; 35)] were relatively immune. The relative wear rates of the five types of hard balls (Rc 50 to 65) were dependent on the corrosivity of the ore. Ranking of the hard balls with respect to wear resistance was consistent for the sulphide and hematite ores in the presence of corrosion inhibition, whereas their ranking was different for the two ores in the absence of inhibition.The electrochemical potential of the grinding balls was measured during grinding and was found to be a useful measurement for assessing the susceptibility of an alloy to corrosive wear. Reduction of ball wear for forged steel and white cast irons with corrosion inhibition was concomitant with a shift of ball potential to less active values. Ball potentials in the presence of inhibition were indicative of non-corroding metal surfaces.IntroductionA PREVIOUS STUDY by the authors (1) showed that corrosion inhibitors - sodium nitrite, sodium chromate and sodium metasilicate - reduced wear of forged steel grinding balls by up to 49% in grinding Ni-Cu sulphide ore. Although the mechanism of wear reduction was not elucidated, it was concluded that corrosion must play a significant role in the wear of grinding media. Remark and Wick (2) of Battelle Pacific Northwest Laboratories have also evaluated corrosion inhibitors for the reduction of metal wear using abrasive and n on- abrasive te sting procedures. Their research was sponsored by 16 companies throughout the world. Preliminary results indicated that anodic inhibitors prevent from one-fourth to one-half of the loss due to corrosion."

Jan 1, 1977

By J P. Bolduc, P. E. Pelletier

Preceded by brief general considerations such as the development of the mining industry in. the Province of Quebec, the choice of plant location, the types of problems studied etc., the paper gives a complete description of this new research and treatment center for metallic, non-metallic and asbestos ores. Facilities for carrying out operations in the three sections of the plant -the sampling section, the ore treatment section and the asbestos section -are fully discussed as well as laboratory facilities for (a) the preliminary testing of ores prior to pilot plant treatment and (b) the grading and testing of asbestos fibre. AT THE beginning of the century, the annual value of the mineral production of the Province of Quebec stood at the $2,500,000 level. Twenty-five years later, it was just under $24,000,000. In 1950, half a century later, it was slightly in excess of $200,000,000. But in 1959, in the span of only nine years, it

Jan 1, 1962

By Barry D. Simmons

Abstract -A well-defined approach is essential to ensure the long-term success of a regional exploration program. Teck's approach in eastern Canada is designed to fulfill corporate objectives while recognizing certain unique parameters for exploration in the area. The elements of this approach include clearly defined objectives, technical considerations and personnel policies, all of which are equally important. The goal is a significant discovery before the mid-1990s and the company is confident that this target will be achieved.

Jan 1, 1992

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Tsuyoshi Hirajima, A. M. Elmahdy, Keiko Sasaki

"Seawater has been reported to depress molybdenite in a copper-molybdenum (Cu-Mo) flotation process at high pH due to the precipitation of Mg(OH)2. Meanwhile, to improve mineral recoveries, collectors are usually added into the flotation cells, thus adding the complexity to the mechanism of bubble-particle interactions involved in Cu-Mo flotation. Therefore, understanding the interaction mechanism in seawater flotation and in the presence of collectors is important to explain the minerals depression. The present work investigated the effect of kerosene on the bubble collision and attachment to pure chalcopyrite and molybdenite surfaces in MgCl2 solution as one of the seawater major components at pH 6 and 11. Mineral surfaces were characterized using atomic force microscopy (AFM). In addition, minerals floatability in the same system were tested in a column flotation. The study of bubble-particle interactions shows that following several collisions, bubble could displace the intervening liquid layer on the mineral surfaces, forming a three-phase contact (TPC). A TPC formed more rapidly in the presence of emulsified kerosene in a 0.01 M MgCl2 solution at pH 6 for both minerals. The reason is kerosene increased the surfaces hydrophobicity and destabilized the intervening liquid layer on the surfaces. Moreover, the average time required to form a TPC was shorter on molybdenite surface. This can be attributed to the effect of adsorbed kerosene on molybdenite surface and molybdenite surface roughness.INTRODUCTIONIn froth flotation, bubbles are used to separate hydrophobic mineral particles from hydrophilic particles. In this process, bubble-particle interactions (i.e., collisions, attachment, and detachment) are crucial with regard to mineral recoveries. The effectiveness of froth flotation depends on the formation of stable aggregates between the hydrophobic particles and the bubbles, allowing the bubble to carry the particles to the froth layer. To form such aggregates, the bubbles and particles must collide, and the intervening liquid layer must be drained below the liquid layer critical thickness, forming a stable threephase contact (TPC) (Ralston & Dukhin, 1999). Particles detachment may take place if the particles still have sufficient kinetic energy and the TPC is not formed. Previous studies of bubble-particle interaction in electrolyte solutions have been conducted using atomic force microscopy (AFM) (Assemi, Nguyen, & Miller, 2008), and by approaching the bubble using mica plate (Pushkarova & Horn, 2008), however, these studies did not focus on the bubble-particle collisions. Bubble collisions and attachment to hydrophobic (Teflon) and hydrophilic (glass) surfaces in a a-terpineol solution have been investigated by Krasowka et al. (2003)."

Jan 1, 2016

By R. F. Baxter, C. M. Read, R. I. McCulloch

"Globalization of the aluminium industry continues to increase the pace of change and the intensity of competition, while simultaneously, society demands better products, cleaner technologies and sustainable industries. Bechtel, a global engineering, construction and project management company, is not immune to either the opportunities or the challenges created by globalization. However, and not withstanding the challenges, for aluminium industry ""players"" with a true global perspective, globalization presents very real opportunities that may be leveraged to deliver value creating goods and services. The following paper will focus on the exploitation of one of the opportunities created by globalization in the Knowledge Management domain - the application of high level tools and methodologies to improve global delivery of greenfield and brownfield aluminium smelter construction projects. Specific examples will be presented of value driven solutions that were delivered at the early stages of project engineering."

Jan 1, 2006

By J. Beddoes

Many high strength aerospace alloys undergo solution heat treatment (SHT) and aging to develop precipitate strengthening. Most simply, SHT involves an isothermal hold in a single phase region followed by relatively rapid cooling to develop a super-saturated solid solution from which precipitates form during aging. However, subsequent properties are sensitively dependent on the details of the SHT, which frequently also serves a homogenization function. Altering the details of the thermal cycle during SHT significantly improves the properties attained during aging, as presented by examples of SHT design for titanium aluminide intermetallics, polycrystalline and single crystal superalloys, and 7075 aluminum.

Jan 1, 2010

By R. Roufail

"Energy consumption in stirred mills has been studied, in the last couple of decades, on a macro scale. Effective operation and meeting particle size required for downstream operations used to be the main objectives behind energy utilization of stirred mills. In this paper, three energy terms are defined to assist in understanding the breakage mechanism for various types of minerals versus mill operation. The types of minerals studied had diverse physical and mechanical properties that are summarized as specific gravity, hardness and crystal structure. The minerals utilized in this study were quartz and galena. The effect of quartz and galena mix has been addressed as well as Lead-Zinc ore sample from SAG mill discharge. The energy input to the mill is function of the agitator speed, therefore three agitator speeds were evaluated, 1000, 1500 and 2000 RPM, respectively. The energy terms studied are specific energy (kWhr/ton). Effective energy is the ratio between net energy and total energy consumed by the mill. Last type of energy is the specific breakage energy, which is the net energy consumed by the mill per one-micron breakage. Results showed that specific energy and specific breakage rate are functions of mineral type, while effective energy is only function of mill input power (agitator speed).INTRODUCTIONGrinding is the largest energy consuming component of a mineral processing operation and typically consumes about 50% of the total energy used at a mining operation (Botin, 2009). Over the last two decades, stirred mills have been extensively utilized in mineral processing operations due to increased mineralogical complexity of ore bodies. Stirred mills grind particles to less than 10 µm by applying a high power intensity. The technology has been the focus of several research studies to investigate mill energy and grinding mechanisms. Becker, et. al. (2001) studied the relationship between different types of energy including input energy, specific energy, volume/mass specific energies, to stress intensity and final product particle size. Other studies such as by Kwade (1999), Kwade and Schwedes (2002), Blecher et al (1996), Partyka and Yan (2007), Stender et al (2004), focused on mill design and/or stress intensity distribution. Peukert (2004) studied the effect of mechanical properties of the grinding media and ground material on the comminution process."

Jan 1, 2016

By Max W. Ball

YOU have been kind enough to ask me to speak to you on "The War and Anglo-American Relations." A speaker always takes the liberty of putting his own interpretation on the scope of his subject. I am going to exercise that privilege, and try to look back over a generation of Anglo-American relationships and forward beyond the present war. I should like particularly to consider responsibilities as well as relationships. A more accurate caption for what I am going to say would be "Anglo-American Responsibilities.?? THE WAR WILL BE WON I am assuming that sooner or later we shall win this war. History and economics point to the same conclusion, that Germany has attempted the impossible and that the seeds of defeat are already sown. As to one ecof1:omic factor, I am already on public record as believing that Germany's oil supply is inadequate for the war she has launched. That opinion is unchanged. Aside from such tangible factors, moreover, I am convinced that the spirit of freedom is unquenchable, and that no combination of powers will be able to rout it from the British Commonwealth of Nations and the United States. Stronger even than this conviction is my faith in a God who will not suffer the defeat of man's aspiration to be master of his own soul. I am sure that all of you share that faith, and that we need not argue it. We can start with the assumption that the war will end in victory. The subject we are to consider, then, is the relationship of the English-thinking peoples during the conflict, and their joint responsibilities in the difficult days that will follow it. A CANADIAN-AMERICAN No talk on such a subject is worth listening to unless the audience knows the background and fundamental beliefs of the speaker. No human statement stands alone; behind and beside and within it are the ideals and the bias of the man who makes it. Because I am a stranger to most of you, I am constrained to talk about myself before I talk about more important matters. The review may be profitable, not because of the subject, but because it may illustrate the evolution of an attitude toward England.

Jan 1, 1941

By E. H. Rose

THE most useful guide to the role of lime in flotation is the view that the chemistry of any flotation operation is primarily a pattern in relative solubilities. We have the coming together of a number of minerals, reagents, fortuitous salts, water, and oxygen, many of which have not been previously in contact with each other, and every one of which is free, at least to some extent, to abandon old alliances and to form new ones. Of one thing the operator may be sure, and that is that, when equilibrium has been reached, those new chemical combinations will have formed which are the least soluble combinations possible to the environment. The laws of solution govern the operation, which means that relative concentrations are always a factor, and temperature frequently is. What the operator is really doing when he chooses his reagents .in the first place (empirically or otherwise) and works out their? optimum amounts, is to provide an environment in which (1) the least soluble possible compound of the mineral he desires to float is one which is also non-wettable, while at the same time (2) the least soluble compounds possible to the minerals he desires to depress are wettable. Since all metathesis is reversible, perfection is impossible to achieve, and the operator is constantly striving to establish that combination of concentrations which will drive each and every particular reaction as far as possible in the direction he desires it to go, in accordance with the law of molar concentration.

Jan 1, 1939

By J. Ander

About fifteen years age some mines in western Canada commenced using Diesel engines, partly for development work but also for operations on quite a large scale. In the Eastern mining field, the Diesel engine made its appearance some eight years ago and has since, at quite a number of mining plants, proved to be a reliable and economical prime mover. As a result, it is today used more extensively than could have been foreseen only a few years ago, and it is reasonably safe to predict that the next few years will see the Diesel engine utilized to a still greater extent in the Canadian mining industry. It is not much more than thirty years since the first Diesel engine was put in operation. During the early years of this century, the Diesel engine took, so to say, its first faltering steps in public service. Since then it has reached a high state of perfection, and its importance has grown in a most remarkable way, until today it is used in practically every field where power is required. It is slowly but surely superceding steam for a great many purposes, as, for instance, for ship propulsion. While in 1921 only about 8 per cent of all tonnage launched was motor-driven, the proportion had grown to 38 per cent in 1927, and for 1929 it was slightly over 45 per cent. Some of the finest passenger liners afloat are Diesel-driven. In the early days, Diesel engines were built only in comparatively small units. Today engines with a capacity per unit of up to 10,000 horsepower, or even more, are being built for marine and stationary purposes.

Jan 1, 1930

By N. R. Thornton

This paper discusses the rapid growth in the application of instrumentation for metallurgical process control. It covers such methods as ultrasonics, pulp density measurements, on-stream X-ray analysis and reagent control, as well as the expanding use of computer control and data acquisition.

Jan 1, 1971

By R. Heikkilä

Today road construction sites utilize more and more information modeling in design phases as well as model based 3-D machine control systems in site operations. For main contractor, the management and control of all the site operations is a demanding task including also many challenges created by continuously developing new technology. In the paper, the main requirements for successful dynamic site management are introduced. The dynamic management means real-time possibilities for information acquiring, transfer and further utilization of the information in the management. An integration model to expand the current way of management and the utilization of present 3-D machine control systems is introduced. Different practical test results using two new different dynamic management systems are presented and evaluated. The first experiments and the results have been provided using the prototype system developed in a research project called DigiINFRA by the University of Oulu and Technical Research Center of Finland. Also, there have been tested a new commercial management system developed recently in Finland. In the conclusion, an expectation for the next generation for more dynamic road construction management methods is concluded.

Aug 1, 2013

Building off the enthusiasm generated by Credit Suisse First Boston on the potential benefits of an industry-wide effort to market gold jewellery, a group of gold producers, led by Randall Oliphant, CEO of Barrick Gold, decides to investigate the long -term impact of launching a significant marketing initiative to stimulate demand for gold jewellery. The group establishes an international Steering Committee representing producers of differing sizes, members and non-members of the World Gold Council. This Committee comprises representatives from AngloGold, Barrick, Gympie Gold, Kinross, Randgold, and Sons of Gwalia and is supported by the Australian Gold Council, the Gold and Silver Institute, and CSFB. The Steering Committee hires McKinsey to assist it by conducting an independent review of whether investment in a large-scale marketing initiative for gold jewellery would be effective in increasing demand for gold, and ultimately of significant economic benefit of the gold industry. Based on McKinsey?s review* and its own discussions with key stakeholders across the industry, the Steering Committee strongly believes the case for marketing is compelling and sufficiently proven to persuade the industry to undertake a major initiative over the next few years. The Steering Committee, supported by McKinsey, conducts briefings with a range of gold producers to share its findings and to understand producers? perspectives on an industry-funded marketing campaign. The Steering Committee is asking for your support to bring this industry-funded marketing campaign to life.

May 1, 2002

By K. S. Raja, B. Pesic, S. Kshetri

"We investigated the electrochemical corrosion behavior of commercial permanent magnetic material (NdFeB alloy) in 0.1 M NaH2PO4 solution (pH:4.75) containing 0 – 1000 ppm of chloride at room temperature (298 K). The material was evaluated in magnetized and demagnetized condition with different surface preparations such as: Ni-Cu-Ni coated, uncoated (bare), and anodized (in fluoride containing ethylene glycol at 60 V for 15 minutes to form a thick nanoporous oxide surface). The nickel coated magnetic sample showed reasonable pitting corrosion resistance up to 100 ppm chloride addition. The uncoated samples showed passivity in chloride free phosphate solution. Chloride additions caused pitting and the pitting protection potential was equal to the corrosion potential with 100 ppm chloride addition. Demagnetization did not alter the electrochemical polarization. However, the passive film formed on the magnetic sample showed higher charge carrier density than the film formed on the demagnetized sample. INTRODUCTIONSintered NdFeB permanent magnets exhibit excellent magnetic properties such as large energy product [(BH)max > 450 kJ/m3], high saturation magnetization (1.6 Tesla), and high coercivity (1.2 – 2.08 x 106 A/m) (Sugimoto, 2011). However, the NdFeB magnets are prone to corrosion attack because of the presence of Nd-rich intermetallic phases, such as Nd4Fe (Jurczyk & Jakubowicz, 2000). Nd-rich and B-rich intermetallic phases are distributed in a matrix of Nd2Fe14B tetragonal ferromagnetic compound in a permanent magnet. Generally, several types of Nd-rich phases are present in the magnet with Fe:Nd ratios ranging from 1:1.2 to 1:7. The volume fractions of Nd-rich and B-rich (Nd1+xFe4B4 type) phases are about 10% and 7% respectively (Li, Ma, Li, & Wang, 2011) . Among these intermetallic phases, Nd-rich phase has the most active electrochemical potential. Therefore, dissolution of this phase occurs in preference to other phases by galvanic corrosion when exposed to moisture. Since Nd-rich phases are present at the grain boundaries of the Nd2Fe14B matrix, corrosion leads to disintegration of the magnet."

Jan 1, 2012

By S. K. Sharma, Sanket Bacchuwar, Prabal Kumar Agrwal, G. V. Rao

"Iron ore processing industries play a vital role in the Indian economy. At present Iron ore of around +64% Fe is used for production of Iron through blast furnace. To produce +64% Fe from low/medium grade ores, crushing & beneficiation is compulsory. But during these processes, large amount of slime is generated. It is estimated that 18% -25% of tailing is generated during the processing of iron ore. The iron ore slime is discarded because of its particle size and chemical composition not being suitable as feed to the blast furnace. Although the fines/slimes can be agglomerated to larger particle, the alumina to silica ratio which is normally more than one pose serious problem during sintering process and subsequent smelting in blast furnace. The alumina content in the slime needs to be reduced for it to be used as the feed for blast furnace. The sample assayed 61.40% Fe, 7.68% SiO2, and 1.52% Al2O3, LOI 2.63% and all other elements were found in critical limit. A series of 27 tests were conducted by using a spiral for optimisation of process parameters to produce a pellet grade concentrate from the stacked slimes obtained from Kirandul. This paper deals with the optimisation studies of various parameters of a spiral concentrator and helps to utilize the fines from tailing ponds.INTRODUCTIONReserves of high-grade iron ores are diminishing all over the world at an alarming rate. As a result, alternative ways of augmenting and conserving precious and non - renewable natural resources are being seriously considered. One such attractive option is the recovery of metal values from slimes / tailings. Iron ore tailings containing around 48 - 60% Fe are generated from the iron ore washing plants and are disposed into tailing ponds without any further utility. These tailings in the form of slimes are not suitable in iron and steel making due to the presence of higher amount of gangue constituents. Several beneficiation techniques have been tried from time to time to reduce the gangue so that the beneficiated products could be effectively used."

Jan 1, 2016

By H. Paudyal, K. Ohto, H. Kawakita, S. Alam, B. Pangeni

The orange waste after lime water modification was converted into promising adsorbents for fluoride by metal loading reaction. The effectiveness and mechanism of fluoride adsorption on metal loaded orange waste gel from synthetic and real plating solution were investigated. Amount of zirconium(IV), aluminium(III), cerium(III), lanthanum(III), titanium(IV), vanadium(IV) and tin(IV) loaded on orange waste from aquearegia dissolution were evaluated to be 1.62, 1.16, 0.93, 0.95, 1.20, 1.12, 0.97 mmol/g respectively. The maximum adsorption capacity (qmax) of zirconium(IV), cerium(III), lanthanum(III), iron(III) and aluminium(III) loaded orange waste for fluoride ions were evaluated to be 1.74, 0.91, 1.07, 0.98 and 1.01 mmol/g from aqueous solution. The mechanism of fluoride adsorption by metal loaded orange waste was inferred to be ligand exchange reaction. Application of zirconium(IV) loaded saponified orange juice residue(SOJR) for real plating solution showed effective removal of trace concentration of fluoride down to the accepted standard. The negligible interference of co existing anions like nitrate, carbonate, sulphate and chloride makes zirconium(IV) loaded SOJR a promising sorbent for waste water treatment. The adsorbed fluoride from fluoride loaded zirconium(IV)-SOJR was effectively desorbed by using alkali solution for its regeneration. This work shed light on the potential application of metal loaded SOJR to remediate fluoride contaminated water for environmental relevance.

Jan 1, 2012

"In the present study, the reduction behavior of composite pellets comprising of iron oxide, synthetic graphite and slags were investigated in a laboratory-scale horizontal tube furnace. Two different types of slags indicating silicate base and aluminate base slags were chosen to examine the effect of slag chemistry on the reduction behavior of pellets. Slag composition of binding materials has influences on the reactions occurring in composite pellets during direct reduction. In-situ high temperature visualization approach was used to observe the slag / iron / carbon interactions at 1773K (1500°C). The off-gases were measured by means of infrared analyzer to determine the reaction rates of the pellets. Different physical appearances during the in situ reaction inferred a strong correlation between the slag composition and internal reactions. In addition, compression tests were conducted to examine physical strength of the pellets. This investigation was carried out to establish feasibility of physical property control of pellets by selecting optimum slag compositions of binding materials INTRODUCTIONCurrently, most of the iron ore mines have facilities that make an ore more usable for the blast furnace operation by improving its physical properties (e.g. pelletizing and sintering). However, during the process, a large amount of fuel is supplied to indurate materials which consequently deteriorate energy efficiency and produce more CO2 emission. Along with increased interests, direct reduced iron (DRI) making process; simply without coke oven or sintering process, has opened the era of clean and environmental friendly iron making process. While some of the established DRI technologies such as Midrex and HYL were restricted to certain locations where natural gas is abundant, coal based technologies using Rotary Hearth Furnace (RHF) such as FASMET and ITmk3 have been developed with regardless of expensive fuel deposit. In addition to the direct use of pulverized non coking coal and fine iron ore, RHF process also has advantages of utilizing waste materials such as EAF dust, biomass and recycled plastics. Nevertheless, there are still many challenges in the coal utilizing technologies as the unprocessed coal and the waste materials contain huge volatiles and ashes. Although recent investigations on volatiles in a RHF process (Sohn and Fruehan, 2005, 2006) have indicated the benefits of coal in terms of iron oxide reduction and have shown feasibility of multi-layer process, carbon composite pellets still have disadvantages because of its weak mechanical bonding strength. As the mixed system with carbon and oxides generates intermediate gases (e.g. CO and CO2) between solid particles, it is difficult to keep its physical state without the help of binding materials. In this reason, industries have been tried to use various binding materials such as bentonite, kaolinite and Portland cement. However, they are still struggling to find out new materials that provide not only sufficient mechanical strength but also metallurgical properties, such as porosity, reducibility and swelling throughout the reduction reaction. Recently, Canadian researchers (Aota et al, 2006) observed enhanced mechanical strength of pellets by using high alumina cement as a binder and concluded that the method could be used to recycle EAF dust as well, but in depth mechanism of reinforced strength has not been concerned. Most of the ashes coming from binders formulate certain type of slag during the reduction process due to its incombustibility. Thus, observation and regulation of slag property is an essential for the control of carbon composite pellet. Yet, only a little thermodynamic consideration from the perspective of slag chemistry has been adapted in the iron and steel making industries as ash has been easily ignored for its tiny proportion. In this study, effect of CaO-SiO2- Al2O3 slag system on the reduction of iron oxide was investigated in terms of"

Jan 1, 2012

By Adrian Dance

Newmont Mining Corporation?s Carlin (?Carlin?) operation processes roaster feed through a double rotator, dry grinding mill following secondary crushing. Metso Process Technology & Innovation (?PTI?) was involved in a review of crushing and dry grinding circuit operations in August 2009. A number of opportunities for increased throughput were identified in the PTI study. Extended plant trials were conducted in July 2010 to provide justification for possible circuit modifications and if needed, additional equipment. The trials confirmed that a finer crusher product would reduce the build-up of material ahead of the coarse grinding chamber in the double-rotator. Also revealed were material transport and airflow restrictions in the dry grinding circuit that resulted in a high circulating load. The secondary crushing plant demonstrated it was capable of reducing the amount of +¾? material in the mill feed thus increasing dry grinding throughput. However, wet and sticky feed affected screening efficiency resulting in low utilisation of the existing crusher capacity. The open circuit configuration also made it difficult to control crushing circuit product size. For the dry grinding circuit, changes in grinding media size, transfer grate design and increased airflow were recommended to reduce circulating load issues and increase circuit capacity. This paper summarises the crushing and grinding circuit review, the extended site trials performed by PTI and the improvements in dry grinding operation that resulted from this study.

Jan 1, 2012

By J. R. Fisher

"Uranium may be leached to some extent in situ from the Blind River conglomerate uranium ores by using the products of bacterial activity from the bacterium Thio-bacillus ferrooxidans his paper describes some of the laboratory techniques used to investigate the characteristics of the bacteria, and to utilize their properties in uranium leaching. The application of some of the laboratory results underground at the Milliken mine of Rio Algom Mines Limited are de-scribed, along with the method of uranium recovery from the mine waters."

Jan 1, 1966