Search Documents

By I. Haskett

ABSTRACT The Redwater pool, in north-central Alberta, was discovered in October, 1948, and at the end of 1950 was about 85 per cent developed. Production is from a Devonian coral limestone reef and is found at an average depth of 3,150 feet. The pool has an estimated .productive area of 37,000 acres, and a maximum oil zone thickness of slightly over 200 feet. Wide variations exist in both type and values of porosity, with the average value determined for the reservoir being 6.16 per cent. The total stock tank oil in place is about 1.24 billion barrels. The crude has a saturation pressure of 485 psig, com-pared to the original value of 1,050 psig for the reservoir, and the principal recovery mechanism so far has been the natural water drive. Cumulative production to January 1st, 1951, has been about 15.5 million barrels. These withdrawals resulted in a reservoir pressure decline of slightly over 100 psi. Predictions of future behaviour indicate that the water drive will not be of sufficient magnitude to maintain the reservoir above saturation pressure past 1953, and that, with natural depletion, the pool will be produced largely by a solution gas drive. Pressure maintenance by water injection has been considered and the possibility of raising the pressure to the original value of 1,050 psig is also discussed. INTRODUCTION WITH the discovery of the Lewduc pool, early in 1947, the Devonian limestone became the major geological formation contributing to Western Canada's rapidly growing petroleum reserves. Redwater, discovered in October, 1948, is now the largest known Devonian pool in Canada, with a recoverable reserve estimated at approximately 500 million barrels. Until recent years, the knowledge of the nature and characteristics of this type of limestone reservoir has been comparatively limited.

Jan 1, 1951

By H. A. Hamza

An experimental study of the settling characteristics of a washery effluent originating as tailings from a froth flotation circuit was undertaken by using a systematic approach to select the most appropriate flocculant(s) under predetermined conditions. Selection and evaluation procedures which greatly reduce the effort required to select flocculants are described. The results show that, although different flocculants display superiority at different ranges of dosage. Separan MG 700 (Dow) is the most suitable on absolute economic grounds. Flocculant evaluation is based on a Cost Performance Index (CPI) which expresses the cost of flocculant (¢/ton) required to produce a unit settling rate (in./hr). From experiments carried out with a number of flocculant aid and flocculant combinations, it was concluded that the use of flocculant aids can be economically justified only if the settling rates required are higher than those obtainable at the optimum flocculant dosage. Otherwise, the value of the flocculant aid appears to be limited largely to the reduction of supernatant turbidity.

Jan 1, 1979

By Vicki Tschirhart, Bill Morris, McMaster University

A new method for mapping faults within basement rocks underlying the Thelon Formation and glacial overburden was developed and tested in the Aberdeen Sub-basin. This method utilizes newly acquired aeromagnetic data, the Blakely algorithm for defining magnetic source edges, a calculated dip-direction map, a digital elevation model (DEM) derived from the Canadian Digital Elevation Database, and the positions of identified, inferred and newly mapped faults that are within and adjacent to this sub-basin. Combining these data revealed three age groups of faults. One group is seen only on the DEM; these faults are young brittle structures that have no effect on the sub-Thelon basement unconformity, and are not visible on the dip direction map. A second group is evident on the dip direction map but not the DEM; these faults are old basement structures that did not propagate upward through the Thelon Formation. The third group is expressed on both the DEM and dip direction map; these faults are also old structures that propagated upward during and/or after deposition of the Thelon Formation. The latter group of faults may be of greatest interest for uranium exploration, with reactivation increasing their potential to serve as conduits to transport uranium-rich fluids and focus deposition at or near the unconformity surface. This methodology has promise for comprehensive mapping of basin faults and tracking the tectonic development of the whole Thelon Basin through time.

Jan 1, 2013

By Matej Petružálek, Václav Vavrycuk, Tomáš Svitek, Tomáš Lokajícek

The most common type of waves used for probing anisotropy of rocks in laboratory is the direct P wave. Information potential of the measured P-wave velocity, however, is limited. In rocks displaying weak triclinic anisotropy, the P-wave velocity depends just on 15 linear combinations of 21 elastic parameters, called the weak-anisotropy parameters. In strong triclinic anisotropy, the P-wave velocity depends on the whole set of 21 elastic parameters, but inversion for 6 of them is ill-conditioned and these parameters are retrieved with a low accuracy. Therefore, in order to retrieve the complete elastic tensor accurately, velocities of S waves must also be measured and inverted. For this purpose, we developed a lab facility which allows the P- and S-wave ultrasonic sounding of spherical rock samples in 132 directions distributes regularly over the sphere. The velocities are measured using a pair of P-wave sensors with the transmitter and receiver polarized along the radial direction and using two pairs of S-wave sensors with the transmitter and receiver polarized tangentially to the spherical sample in mutually perpendicular directions. We present an inversion method for elastic parameters describing general triclinic anisotropy. We demonstrate on synthetic tests that the inversion becomes more robust and stable if the S-wave velocities are included. This applies even to the case when the velocity of the S waves is measured in a limited number of directions and with a significantly lower accuracy than that of the P wave. Finally, we analyze velocities measured on a rock sample from the Outokumpu deep drill hole, Finland, including the error analysis for several levels of confining pressure.

Jan 1, 2015

By J B. McConnell

The Thompson smelter has three unique features which form the basis ~f its design: fluid bed roasters which treat nickel concentrate filter cake from the mill, as well as the flux, in order to achieve partial desulphurization; the use of electric furnaces for the smelting of the partially desulphurized, preheated roaster product; and the disposal of slag by water granulation and slag slurry pumping. The installation consists of three fluid bed roasters, each feeding an electric furnace. Nickel concentrate is received at the smelter via pipe line. It is thickened and filtered, and the filter cake, together with siliceous flux, is fed through rotary bin feeders and reciprocating double-gate seals into the fluid bed roasters. Air injected into the roasters through club-head tuyeres oxidizes part of the sulphur and associated iron in the concentrate. The heat of reaction dries and heats the charge. Roaster product is recovered from the gas stream in cyclones and from the roaster bed through automatic valves.

Jan 1, 1963

By L. Kilburn

"A survey of 281 mineral exploration agreements examines the ratios among three ways that may be used to purchase an interest in a mineral property, viz: pay cash, pay shares and make future expenditures on the property.The dollar value of the future expenditures exceeds that of cash or shares by about nine times in most of the 110 agreements that contain cash-expenditure or share-expenditure components. Results suggest that cash and shares are treated about the same in terms of value.Buyers and sellers have opposing priorities for the way that they prefer to purchase a mineral property. These opposing priorities should give rise to a perceived 50:50 balance between cash/share payment and future expenditures to satisfy the idealized situation described by most definitions of fair market value (FMV). This balance between cash/share payments and future expenditures appears to be rationalized in negotiations to a FMV when expenditures are nine times greater than cash and/or payments.On this basis, it is proposed that the FMV of a property may be determined by aggregating the dollar amount of the cash/share payments plus one-ninth the dollar value of future expenditures, as set forth in the respective purchase agreement, and proportionately applying such aggregate to full property value."

Jan 1, 2005

By D. Vanin

"Conventional single heading track drifting in the hard rock mining industry has not shown any significant improvements in advance rates, despite the advent of modern track jumbos and igh speed muck handling systems .This paper presents Kiena 's experience in using a 7 ft 2 in. diameter larva Mark 6 Tunnel-Boring Machine (TBM) for driving 6000ft of drift.IntroductionKiena Gold Mines is located about 5 miles west of the town of Val d'Or, Quebec, approximately 300 miles north of Montreal. The mine commenced production in October 1981 and has gone through various expansions of ore production with 287 916 metric tonnes in 1982 to reach 453 800 metric tonnes in 1986.Due to the majority of claims being covered by a lake, a grassroots exploration drive of remote areas of the property was required to allow diamond drilling on a yearly basis. High speed sequential excavation methods (SEM) of single heading drifting in the mining industry has not progressed much in the past 20 years despite the advent of electric-hydraulic jumbos, Haggloader and Hagglund type cars. Certain examples of record SEM drifting advances have been performed in the past but only under very specific ground and cost conditions."

Jan 1, 1987

By M. Girard, E. Bourricaudy, M. Ashbury, M. Canizares, A. Mezei

Liquid-solid separation and slurry handleability relate directly to commercial plant ramp-up success or lack thereof. The paper provides a well-proven approach for testing, scale-up and commercial application of difficult processes. Emphasis is placed on practical applications of rheological concepts developed both academically and empirically. The cause-effect relationship between the process chemistry and possible physical implications on the metallurgical plant operability is presented in a simple, direct form. Examples include recent results in areas of mineral processing and extractive metallurgy. Technical process risk factors and their mitigation are included in the discussion.

Jan 1, 2011

By Gérald Riverin, Bernard Salmon, Marlo Gagnon, Réemi Asselin, Alain Cazavant, Michel LaBrie

"The Ansil deposit is located in the Noranda mining camp in the southern part of the Abitibi greenstone belt. /twas discovered in 1981 and production began in 1989 with proven reserves of 1.58 Mt grading 7.2% copper, 0.9% zinc, 26.5 glt of silver and 1.6 glt of gold. It is centered at a depth of 1.3 kilometre and represents one of the deepest ore discoveries ever made from surface.The deposit consists of a single massive sulphide lens located at the contact between the Northwest Rhyolite and the Rusty Ridge Andesite. The lens strikes north-south and dips 50° east. The thickness of the lens may reach up to 35 m and can change very abruptly both along strike and along dip. The maximum thicknesses of the sulphide lens are reached in its upper (western) and at its lower (eastern) edges, thus giving the deposit its present shape of two sulphide domes connected by a thinner central portion. The lower dome is underlain by a thick accumulation of massive magnetite which may reach 10 to 15m in thickness. The upper and lower domes are underlain by two distinct pipe-shaped zones of stringer and disseminated sulphides which merge with a larger stringer zone at depth.The Ansi/ deposit displays strong relationships between its morphology and the distribution of metals. Hydrothermal alteration consists of chloritization and sericitization. Chlorite alteration is closely associated with stringer sulphide mineralization while sericite is developed in diffuse zones bordering the chloritic zones. Unlike other similar deposits, the Ansil deposit is characterized by very extensive alteration and sulphide mineralization in the hangingwall of the massive sulphides. Several features of the deposit are consistent with an origin from a submarine hydrothermal system which was particularly long-lived, and which thus promoted the build-up of very high fluid temperatures with extensive replacement (and enrichment) of pre-existing sulphides after their original deposition onto the seafloor."

Jan 1, 1990

By Victor Dolmage

Introduction Although gold production in British Columbia began in 1859, lode gold was not produced till 1893. Since 1900, the annual production of lode gold has fluctuated between $3,000,000 and $6,000,000. About twenty per cent of this production may be regarded as by-product gold from base metal mining. The remainder comes from a few isolated but important mines, such as the Rossland mines, Nickel Plate, Surf Inlet, Premier, Pioneer, Bralorne, Reno, and Cariboo Gold Quartz, and from several less important mines. All of the above, except Pioneer, Bralorne, Reno, and Cariboo, are approaching or have reached the point of exhaustion, but all are now receiving, under the stimulus of the. present gold-mining boom, drastic resuscitative treatment, with, in some cases, signs of resurrection. Notwithstanding this, however, the main interest at the present time is focussed on the Bridge River and Cariboo fields. Both these fields were discovered in the early 'sixties' and, apart from the Cariboo placer production, both have from time to time contributed small amounts of lode gold; but it is only during the last two years that the real possibilities of these areas were discovered. and that they began to assume the appearance of goldfields of major importance. The two fields are sorme three hundred miles distant from one another and contain deposits of distinctly different types, so that the only reason for including them in one article is the fact that they came into prominence more or less simultaneously and at a time coinciding with, but not otherwise related to, the present gold-mining boom.

Jan 1, 1934

By F. M. Doyle, G. Sidhu, A. J. Dussault, A. Raygani

There is a growing demand for rare earth metals for use in high strength permanent magnets, most notably Nd2Fe14B. Rare earth metals are extremely reactive, with reduction potentials around -2.5V SHE, and are conventionally produced by molten salt electrolysis. The current work was done to investigate an earlier report of electrodeposition of a neodymium ferroalloy from aqueous solution, to determine whether this approach could be an environmentally and economically competitive commercial approach for producing feedstock for permanent magnets. Such a process would be analogous thermodynamically to the Castner- Kellner process, in which aqueous sodium chloride brine is electrolyzed in cells with mercury cathodes. Metallic sodium forms an alloy (amalgam) at the cathode, thereby lowering the activity of the metallic sodium significantly below unity and making the reduction potential of sodium significantly less negative than the standard reduction potential. Here we report the effects of Nd/Fe ratio in the electrolyte, current density, temperature and two different complexing agents, glycine and cysteine, on the composition and morphology of the electrodeposits, along with current efficiency. The energy needed to produce neodymium as Nd:Fe alloys by aqueous electrodeposition was compared with values estimated for production by molten salt electrolysis and the thermodynamic energy requirement.

Jan 1, 2014

By F. H. Edmunds

I N presenting this paper, the writer wishes to point out some of the difficulties and problems of geological work in that part of Saskatchewan in which outcrops are few. These problems are well known to all geologists who have made investigations in this region, but may not be so well known to those outside. A table of the strata as known in certain areas of Saskatchewan and the adjacent provinces is given, with a brief discussion of some of the formations and beds about which there is little knowledge due to their being deeply buried and not exposed in the region. Comment with regard to possible oil and gas structures is made and some features of the structures in the Battleford and Simpson districts are described. The writer wishes to make acknowledgment to members of the Geological Survey of Canada to whose work in Saskatchewan and the adjacent provinces reference is made, and to others who have made, or are making, valuable contributions to the stratigraphy of Saskatchewan. Mr. G. C. Webb has kindly furnished information regarding and materials taken from a well bored recently in the Paynton district. Special thanks are due to the Simpson Oil and Gas Company for permission to use much valuable information with regard to their wells and for the generous way in which the officials and staff co-operated with the writer. The opportunities the writer has had to visit many parts of the Province have been in connection with investigations for the Provincial Department of Natural Resources and through facilities provided by the Department of Soils of the University of Saskatchewan. To these Departments the writer accords his thanks. For the purposes of this discussion, Central Saskatchewan may be considered as that portion of the Province extending from Township 16, with Regina, Moose Jaw, and Swift Current situated on or near the southern boundary, to Township 48, with Prince Albert and Lloydminster on the northern boundary. This region includes territory underlain by Cretaceous sediments and excludes the southern portion of the Province, where Tertiary beds underlie the surface and are exposed to an extent sufficient to permit a measure of systematic mapping.

Jan 1, 1937

By Roger V. Pierce

IN the last few years, much study has been devoted to increasing stoping efficiency. The reasons for this are shortage of manpower, shorter working hours, operating regulations, and shortages of essential materials. More efficiency in mining methods is needed to offset these adverse factors. In the past, attention has been centred upon haulage, hoisting equipment, mill flow-sheets, etc., but recently the spotlight has been focused on the cost of stoping and the cost of handling materials. Scrapers and scraper hoists have thus assumed greater importance. In order to make it possible for certain orebodies to be mined at a profit, it has been necessary to apply assembly-line practices to the streamlining of mining methods. All cycles of the mining operation must balance, and the sooner broken ore is removed from the working face, the sooner another round can be started. Since the introduction of scraper hoists in metal mines more than thirty years ago, much progress has been made in their design and application. Alert operators are now constantly watching for methods in which to apply scrapers. The saving of manpower in development work and the changing of mining methods that once employed manual handling of materials are increasing vital wartime tonnages. Essential ores from newly discovered orebodies are moving rapidly from stopes to reduction plants-because it is now possible to develop an orebody and place it in production with a minimum of manpower and development work. Today, speed is one of the prime essentials o mining. Everywhere, there is a concentrated effort to use experienced miners in breaking rock, in timbering, and in carrying out the various phases of mining that require many months of training. Much effort is being made to mechanize the working places because experienced men naturally prefer to work where the majority of materials are handled mechanically. In line with this policy, many new men are being taught the details of scraper work, because even green men can quickly become acquainted with scrapers and thereby release older heads to perform the more skilled phases of mining.

Jan 1, 1943

By S. Nikolic

"Calcium ferrite slags are currently used in a number of copper-converting processes. Despite the industrial importance of this system the phase equilibria have not been fully investigated. Characterization of this slag system is necessary to improve the control of process parameters, including fluxing and operating temperatures. Recently, a modified experimental method has been developed; this involves rapid quenching of slag samples equilibrated at high temperatures with the resulting phase assemblages analysed using electron probe microanalysis (EPMA). In the present study, experiments were completed under controlled temperatures and oxygen partial pressures using CO/C02 or H2/C02 gas mixtures. The investigated slags were supported during equilibration by a substrate of the primary phase. This technique removes the limitations arising from the use of crucibles and facilitates rapid quenching of the melt. Experiments were carried out at 1200°C and 1250°C (1473 Kand 1523 K) and in the composition range 0-40 wt.% Cu20, 0-25 wt. % CaO and 45-80 wt. % Fe203. Liquidus and solidus data are reported for the primary phase field of spinel between the oxygen partial pressures of 10-4.5 to 1 o- 6-5 atm. The analyzed compositions of liquids and solids are used to construct the phase diagram of ""Cu20"" -CaO-""F ez03"" system in equilibrium with metallic copper at fixed oxygen partial pressures."

Jan 1, 2007

By Guy Archambault, Réal Daigneault

"Un trait marquant du cadre tectorwstratigraphique de la Sous-province de l'Abitibi est la présence de nombreux couloirs de déformation d’extension régionale et sub-concordants au grain stratigraphique. La présence de grandes masses granitoïdes qui perturbent l'allure du grain tectonique est typique de la partie nord de la Sous-province de l'Abitibi. Des rides E-W constituées de complexes plutoniques précoces forment des reliefs structuraux agissant comme des moles résistants qui interfèrent avec la déformation régionale.Deux types de couloirs de déformation sont distingués, les couloirs de bordure et les discontinuités structurales. Les couloirs de bordure représentent des auréoles de déformation élevée qui s’accompagnent généralement d’un métamorphisme au faciès amphibolite. lls suivent /'interface entre les roches granitoïdes et les assemblages supracrustaux. Ces couloirs sont de puissance kilométrique et sont confines, surtout au sein des roches vertes, a l’interface des complexes granitoïdes d’importance. La limite entre la Sous-province de l'Opatica et les roches supra crustales de l'Abitibi est caractérisée par un important couloir de bordure issu possiblement d'un chargement tectonique irrégulier et concentre lors du raccourcissement horizontal.Les discontinuités structurales sont des failles ductiles qui se propagent surtout en direction E-W mais avec des variantes de directions SE et NE. Les discontinuités E-W se caractérisent par la présence d'une linéation d'étirement à fort angle de chute. Les discontinuités SE sont caractérisées par des linéations d'étirement horizontales et directionnelles et les mouvements observes sont system attiquement dextres. Les discontinuités NE sont des failles à comportement beaucoup plus fragile et se distinguent par des composantes de mouvement senestre. Elles sont tar dives par rapport aux discontinuités E-W et SE et ne représentent pas la symétrique du système SE.La combinaison des systèmes E-W et SE décrit un motif anastomose a l' échelle régionale. Les failles ductiles se rejoignent defaçon asymptotique, isolant des blocs peu ou pas affectes par la déformation. L'anastomose est un phénomène qui se produit a toute échelle et est reliée principalement aux Mt érogénéités et aux anisotropies 1) des forces agissantes (champs de contraintes régionale et locale) et 2) de la réponse del' empilement supra crustal (compositions différentes, fabrique initiate, propriétés mécaniques variées, niveaux d'altération).Dans le but de respecter un raccourcissement horizontal N-S, différents modelés sont proposés; ils mettent en cause soit une transpression dextre, soit des failles inverses réactivées en failles décrochèrent dextres soit des failles de chevauchement redressées."

Jan 1, 1990

By J. -P. Lempainen, K. Haavanlammi, K. Valkama

The Outotec nickel matte chloride leaching process is especially suitable for small capacity standalone nickel refineries. The matte is leached with hydrochloric acid and oxygen in multiple steps in atmospheric OKTOP® reactors. Oxygen feed prevents reductive conditions and hydrogen formation in the leaching process. A sufficiently high acid concentration keeps the iron dissolved in the solution. The iron is removed after leaching by precipitation and the pregnant leach solution continues to metals recovery. The metals recovery from the chloride solution is done by solvent extractions, where ammonia is used for pH control. Copper and nickel are stripped from the organic phases into sulphate solutions. Metals can be recovered from the purified solution by conventional electrowinning. Other alternatives are precipitation or hydrogen reduction processes. The ammonium chloride in the solvent extraction raffinate is regenerated into ammonia. The calcium chloride solution from ammonia regeneration is routed to acid regeneration where sulphuric acid is added and ultra-pure gypsum is precipitated. The hydrochloric acid solution from this step is recycled back to leaching. The process yields good overall metal recoveries and expensive

Jan 1, 2014

By M. B. Kime, E. K. Kanowa

"Heap leaching of low-grade copper-cobalt oxidized ore and solvent extraction of copper, cobalt, manganese, and zinc were investigated. Heap-leaching parameters were optimized using agitated and tray batch leaching tests, capped by tests on a pilot semicontinuous heap-leach plant. The optimum pregnant leach solution yielded 2,350 mg/L Cu, 3,800 mg/L Co, 3,600 mg/L Fe, 130 mg/L Mn, 25 mg/L Zn, and 0.58 g/L solids in suspension, with pH and acidity of 1.27 and 3.66 g/L, respectively. Copper, cobalt, and impurities (Mn and Zn) were extracted using (v/v) 30% CP-150, 20% IONQUEST® 290, and 20% D2EHPA, respectively; overall recoveries of copper, cobalt, and impurities were 98, 99, and 70%, respectively.RÉSUMÉ La lixiviation en tas des minerais oxydés de cuivre et de cobalt et l’extraction par solvant du cuivre, du cobalt, du manganèse et du zinc ont été étudiés. Les paramètres de lixiviation en tas ont été optimisés à l’aide d’essais de lixiviation en discontinu sur un plateau, complétés par des essais relatifs à une usine pilote de lixiviation en tas en semi-continu. La liqueur-mère optimale a produit 2 350 mg/L de Cu, 3 800 mg/L de Co, 3 600 mg/L de Fe, 130 mg/L de Mn, 25 mg/L de Zn et 0,58 g/L de solides en suspension, avec un pH et une acidité respectifs de 1,27 et 3,66 g/L. Le cuivre, le cobalt et les impuretés (Mn et Zn) ont été extraits avec un pourcentage volumique (v/v) de 30 % de CP-150, de 20 % d’IONQUEST ® 290 et de 20 % de D2EHPA, respectivement. Les récupérations totales de cuivre, de cobalt et d’impuretés étaient de 98 %, 99 % et 70 % respectivement.INTRODUCTIONBoss Mining S.P.R.L. is a privately owned hydrometallurgical plant located in southeastern Democratic Republic of Congo. It treats oxidized ores of copper and cobalt that are recovered by sulphuric acid heap leaching (Trujillo, Cisternas, Gálvez, & Mellado, 2014; Kime, Kanowa, Mulaba- Bafubiandi, & Diyambi, 2016) and solvent extraction processes (Crane, Urbani, Dudley, Horner, & Virnig, 2009; Fisher, 2011; Kime et al., 2016). The ore to the plant is primarily sourced from the Luita and Mukondo mines. Geological prospecting work by Gecamines and Boss Mining showed that the Mukondo mine contains a very large cobalt reserve not yet exploited, but with grades as low as 0.2%.Currently, Boss Mining is focusing on the production of copper, but is investigating methods to efficiently produce both copper and cobalt. A challenge in the production of cobalt from this ore is its presence in the third oxidation state. This requires the addition of reducing agents, which increases the overall operating cost (Kime & Makgoale, 2016). Cobalt solvent extraction is also very sensitive to impurities such as nickel, zinc, manganese, and aluminum, which are often co-extracted (Swartz, Donegan, & Amos, 2009). This sensitivity to impurities requires the optimization of operational parameters to lower impurity levels as much as possible in the electrolyte."

Jan 1, 2017

By A. D. Hunt

THIS PAPER will review Canada's fossil fuel situation as we understand it today and indicate some of the options available to meet our energy requirements during the next 15 years. It would therefore be helpful to examine Canada's total energy requirements and discuss the un certainties of the data base on which we must base future energy investment decisions. On the world scene, Canada is at the top of the energy-consuming nations, using about 49 bbls of oil equivalent per caput/ year. This appears to be slightly ahead of the U.S. and of course much higher than that of many countries. It is generally accepted that there is a more or less direct relationship between energy consumption and material standard of living. However , as we know, Canada, when compared with other industrialized countries on a GNP, an individual-income or some other standard basis, is lower in the list. This situation may be explained by our more severe climate and a relatively small population distributed over a land mass second only to that of the Soviet Union.

Jan 1, 1977

By Daniel E. Walsh, P. D. Rao

"A four-inch compound water cyclone (CWC) was tested to evaluate its gold recovery characteristics when processing -4.8 mm run-or-pit, placer material. Neutron activated placer gold particles (840 to 37 microns) were used as radiotracers (/98Au) in a closed circuit ewe test loop to determine concentrator recovery; a procedure believed unique to this study. The effect on gold recovery of gold size and shape, feed pulp density, feed pressure, vortex finder clearance (VFC), ewe cone type, top-size of the feed solids, presence or absence of heavy minerals in the feed, and the quantity of-37 micron slimes in the feed was investigated in over 300 tests.CWC concentration ratio and the top-size of the underflow solids were both affected by cone type, VFC, and feed pressure. Gold recovery was significantly affected by gold size, gold shape, and concentration ratio. These effects are complex, because significant size-concentration ratio and size-shape interactions exist. Radiotracer techniques showed gold particles had a residence time within the ewe of approximately one second. This study suggests ewe gold recovery is a concentration. This work suggests ewe gold recovery is a function of particle size and shape, and the flow rate through the cyclone. CWC cone ""bed density"" is considered important only as a thin, protective layer, which shields coarser gold particles from the entraining currents and facilitates their movement through the CWC.IntroductionCompound water cyclones (CWC), or automedium cyclones, are enhanced gravity concentrators for the beneficiation for slurries of sand, coal, and ground ore (Fig. 1). They are called compound water cyclones because of the compound slopes of their basal cones (Fig. 2) and are operated to suppress classification phenomena in favour of gravity concentration effects. The compound water cyclone is not a new wet concentrator. It was developed in the late 1950s by Dr. Jan Visman through research sponsored by Canada's Department of Energy, Mines, and Resources. Since that time, it has become a common unit in coal washeries for cleaning fine coal. CWCs and other versions of concentrating cyclones have also shown promise for heavy minerals and precious metals recovery."

Jan 1, 1988

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011