Search Documents

By Meyer C. F

The increasing use of continuous miners in the extraction of high coal seams has amplified the need for enhanced ventilation systems in the headings. Owing to larger face dimensions and higher production rates, more ventilating air is required to effectively dilute liberated methane to acceptable concentrations. However, the increased air quantities raise and entrain greater amounts of dust, to which the operator is subjected. Various methods (eg sprayfans, on-board scrubbers and jet fans) are used in various configurations and combinations to ventilate the headings. These arrangements generally result in a complex air flow pattern, which complicates achieving an optimum balance between diluting methane and minimising dust capture. In order to cost effectively investigate and propose solutions to this problem for the South African coal mining industry, the Division of Mining Technology has embarked on an extensive work program to evaluate various ventilation methods presently in use. Four currently generic ventilation patterns in various heading scenarios have been simulated using the Computational Fluid Dynamics (CFD) computer program. Evaluating these outputs against a predetermined set of criteria allows the best system for a particular situation to be chosen. The program also facilitates fine-tuning of an adopted system without incurring the cost and inconvenience of doing such tests in situ. This process not only provides solutions at significantly reduced costs, but also yields deeper insights into the factors affecting heading ventilation than hitherto possible.

Jan 1, 1995

By G L. Simmons, K M. LeVier, R Kappes

The low potential hydrophobic state of pyrite in amyl xanthate (PAX) flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at NewmontÆs Lone Tree Plant in Nevada. Initially, the N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments, and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Experimental results show the importance of the pyrite surface state and the rather interesting features of the activation process.

Jan 1, 2005

By F Mavroudis, M Gaastra

Due to the increasing demand for resources worldwide, efficient utilisation of raw material deposits and recycling technologies become more and more important. Growing industrial nations and increased living standards require a large raw material supply. Hereby responsible handling of existent primary and secondary raw materials is indispensable. By utilising state-of-the-art technologies resources are extracted, recovered and recycled more efficiently which increases sustainability. Hereby sensor technologies combined with intelligent data processing systems in particular provide a considerable research area. Innovative sensor technologies are already implemented during recognition of material-specific characteristics, during elemental recognition as well as during machine control. They are applied to attain increased automation levels of mining machineries, higher recoveries during mining and processing as well as higher recoveries. To be able to face the increased demand for sensor technologies and the integration into raw material industries, an interdisciplinary association of three RWTH Aachen University Institutes has been founded. The association has expertise on increasing productivity and capacity utilisations by automating mining and recovering processes by sensor technologies. Due to the utilisation of sensor systems, materials and structures can now be detected and elementary analysed on a real-time scale. The developed and enhanced techniques are the key for any ambition of autonomous plants and machineries. This paper gives an overview on the regarded sensor technologies for material recognition, machine automation and mineral processing. The authors present concepts based on extensive laboratory and field studies of successful implementation and application the technologies considering special mining conditions. Overall three applications are described to demonstrate the potential of sensor technologies for autonomous and sustainable mining: real-time analysis: recognition of elementary compounds during extraction processes; multi-sensor system EiControlPlus: designed for automation of longwall shearers by complete detection of the machineÆs environment; and sensor-based sorting: applied in recycling and mineralÆs industries.

Sep 26, 2011

All companies and individuals who embark on a business venture incur costs. For the most part these costs can be conveniently categorised, firstly into capital and operating costs and then into the various elements of these major cost centres. Although the nature of expenditure naturally differs as between industries certain broad cost types are characteristic of all heavy industries. The capital costs of gaining access to an orebody, equipping a new mine, building a treatment plant and perhaps refining and smelting facilities are likened to capital expenditure by a manufacturer on new plant and equipment required for an expansion or new product innovation. Similarly the day to day costs of labour and materials employed in the running of a mining operation can be likened to similar costs in other heavy industry. There is another group of costs that are not so easily categorised. Most industries incur unavoidable costs that do not form part of the direct or capital costs of physical production. These costs include taxes and other payments to government and research expenditure. The mining industry has a particularly heavy burden of non-production costs and it is the objective here to highlight and analyse a few of them. These costs are exploration expenditure, infrastructure expenditure, royalties and income tax. This is not to suggest that these are the only major non-production costs that the mining industry needs to bear. The industry may incur significant costs for environment protection, land tenure maintenance and on liaising with Government on a wide variety of matters. It is for reasons of subject manageability that the list is confined to the four costs mentioned. For the mining industry, exploration and infrastructure expenditure, royalties and income tax have several distinguishing features. Firstly, they are generally proportionately large costs. Exploration and infrastructure expenditure for example, could well exceed mine development costs. Depending on how royalties are levied, they may be very high in relation to profits earned and many in fact exceed profits. Secondly, except for income tax, they are costs that are generally not payable by other industries. Exploration expenditure is in some respects comparable with industrial research and development. However, because mines are wasting assets exploration is necessary for survival, and it is likely to form a larger part of costs per dollar of profits or sales than R&D. It can therefore be said that exploration is of far more significance to the miner than R&D is to the typical industrial company. Furthermore, unlike exploration expenditure, R&D results are transportable and patents permitting, transferable. The infrastructure burden that miners must carry is unique to the industry. Whereas urbanised industry is not usually liable for the capital cost of power, water, transport, townships and community facilities, the miner must finance these projects himself. Neither the payment of royalties, nor of course, income tax are unique to the mining industry. Royalties are more properly described as a unique charge on some primary industries but however described, they are a charge that manufacturing and service industries do not have to pay. Whilst we all pay income tax, the mining industry's uniqueness derives from the special problem that the industry has in arriving at annual net income in view of the capital intensity of the industry, partly due to expenditure on infrastructure, the indefinite life of capital equipment and its unpredictable residual value, funds expended on exploration and long lead times associated with a mine development. The third distinguishing feature of these costs is that, with the possible exception of exploration expenditure, they are heavily influenced by the policies and actions of Government. As such the industry has a responsibility to promote the industry by emphasising its potential to improve national product including exports and by requesting that the Government provide for the industry in its long term planning and seek its co-operation to prevent the industry incurring inequitable penalties relative to other industries.Finally, exploration and infrastructure expenditure are significant because they are front-end charges on a project. When due allowance is given the time value of money and the deferment of income from a mining development to which they relate, exploration and infrastructure expenditure assume greater importance than the raw money expenditure suggests. For all these reasons, exploration and infrastructure expenditure, mining royalties and mining income tax are worthy of detailed study. This is the purpose of this paper. The objective is to examine the determinants that give rise to them and provide some thoughts on their impact on on-going and potential mining developments and, where relevant, to make some suggestions as to how they may be minimised.

Jan 1, 1977

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

The potential of the developed multi-dimensional analysis system to assist interpretation from large data sets through derived digital mapping models is presented accompanied by preliminary results. The concept learning model is original and its application general. Applications exist in general science, engineering, earth resource management and economics. The developed system incorporates advances in machine learning, neural networks, object-oriented software engineering, knowledge representation and fuzzy logic. ' The specific application presented involves automatic earth resource modelling and assessment involving geological theories of mineral potential. The developed system functions as a new and powerful mineral exploration tool, To date the model has been trialled on an earth resource database and several published data sets. A more general potential application is knowledge discovery within databases. The specific theory that is tested in the experimental results is the nature of the cause-effect relationship between the hypothesised geological causes and the measured effects within a previously published test survey. Also integrated here are a neurophysiological cerebellar model of human learning, a new concept similarity measure for pattern recognition, modelled components to explain human concept formation through knowledge discovery and a means of permanent representation.The implementation is as a new artificial neural network architecture functioning as a hybrid expert system. Understanding of programmed concept learning is extended through the model. Also established is a basis for a new approach to multivariate data analysis. Spatial analysis for decision support is integrated over many dimensions, relationships, data types and data modes. Application of the developed methodology and system adds value to data bases. Discovered knowledge is represented as new generalisations, interpolations, classification hierarchies, aggregations and associations within a dynamic, maintainable and reusable integrated knowledge framework. New digital knowledge products and intelligent access follow. Permanently stored, maintainable, easily accessible and discovered knowledge improves decisions through extended hypothesis testing, spatial data analysis and inferencing, prediction, logical deductions and explanations.

Jan 1, 1995

By J Vann, C Seymour

Geology is generally treated as a æfront endÆ step in mine development. After infill drilling, the majority of resource estimation, mine-planning, development, mineral processing strategies and operational procedures are planned and implemented with little geological input, particularly in open pit operations. However, significant benefits in overall costs, cash flow, and technical risk reduction can be realised when sound geology is utilised more rigorously throughout the mining process. This under-utilisation of geology in the mining process has arisen due to a combination of factors:A lack of interest in, or knowledge of the full mining process by geologists. Few geologists fully understand where their inputs make critical impacts on downstream users. As a result of this, geologists generally do not focus their inputs towards areas of greatest value added, ie addressing issues critical for other members of the mining team. Most importantly, few geologists effectively communicate their results to the downstream users of their geology models. The results are that the potential benefits of geology, and the appropriate status of geology in the mining industry, are not fully realised. It is fundamental to realise exactly what geologists do. Geologists constrain geological processes and geometry. All geoscientific tools at the geologistsÆ disposal are geared towards one of these goals. An emphasis on geological processes is present throughout the exploration process, whereas in the resource estimation and mine development process an emphasis on geometry is required. The mining process is a web of disciplines that are attempting to optimise development of a resource to provide value to shareholders. Yet few people within these disciplines have a full appreciation of this web, and where sound geology inputs can add value through various feedback loops. Geology inputs do not end at the resource estimation stage, nor are they relegated to grade control implementation. If geologists have an appreciation of the mining process and close liaison with the other disciplines such as geostatistics, geotechnical engineering, hydrogeology, and mining engineering, they can significantly benefit project costs, timelines, and constrain technical risk by addressing their issues at the earliest possible stage. Furthermore, the mining process is not a single pass timeline, but an iterative process where the exploration, resource definition, mine planning and mining loop is continually repeated over the life of a project. Therefore, the potential inputs of geology are critical throughout the mining process. Effective communication of the impacts of geology inputs on downstream users is often lacking on mining projects. The most effective way to communicate geological results is through where it impacts most û project risk. Focussing all geology inputs and communication in terms of potential material risk allows the geologist to be more effective in contributing value to the mining process, and allows the downstream users of geology inputs to better constrain the risks associated with their aspects of the mining project. Through a program of geologists:taking an interest in the entire mining process and identifying critical areas for geology inputs to downstream users (the geologistsÆ clients); focussing geology inputs to address the potentially material issues on mining projects; and communicating their inputs to the æclientsÆ in terms of technical risk, geology will be much better integrated into the mining process. As a result, the potential benefits of geology throughout the mining process will be realised, and the status of geologists within the mining process will be elevated to a more pivotal position.

Jan 1, 2000

By T Muri

The drying operation of materials from particulate solids, through slurries and suspensions, to continuous sheets represents an important part of several processes in the chemical and mineral industries. The increasing demand of high productivity at low cost and minimal environmental impact makes it complex to evaluate and choose the best available drying technology for each industrial application. The drying technologies are mainly characterised on the basis of how the wet product is related to the drying medium, namely: direct and indirect drying. In the direct drying method (convection drying), the product is brought into direct contact with the drying medium, which may be hot gas or air. Large quantities of gas are necessary for transfer of the required energy. A special case of the direct dryer is the fluid bed dryer, in which the product floats on a cushion of air or gas. The process air is supplied to the bed through a perforated distributor plate and flows through the bed of solids at a velocity sufficient to support the weight of particles. Very high heat and mass transfer values are obtained as a result of the intimate contact with the solids and the relative velocities between individual particles and the fluidising gas. In the indirect drying method (conduction or contact drying), the wet product is separated from the drying medium. The drying unit can consist of a rotor forming the indirect contact heating surface mounted in a stationary or rotating shell. The indirect method uses saturated or superheated steam resulting in low energy consumption and minimal environmental impact. In this paper, a review is given of the technologies available on the market based on different drying methods. The advantages and the disadvantages are summarised with respect to issues such as investment and operating cost, maintenance, product capacity, product handling and environmental impact.

Jan 1, 2006

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

By J Johansson, J Lööw

There are many reports about how the new technology will affect our work, sometimes they are utopian but often dystopian. Most of the visions describe the industrial work, while the work of the managers does not seem to be affected. In this article, the authors will discuss how the new technology within the concept of Mining 4.0 changes the conditions for leadership and the work of managers in a modern mining industry.

Sep 1, 2024

Thiess Dampier Mitsui's Moura-Mine is located in the south-eastern corner of Queensland's Bowen Basin, some 180 kms west of Gladstone. Current requirements of the open cut operation are to drill and blast 25 million cubic metres of overburden per year, consuming some 12,000 tonnes of explosive in order to meet the requirements of the mine's four operating draglines and one overburden shovel. By early 1985 it had become obvious that the existing drill and blast equipment and technology could not cope with the long-term needs of the open cut mining operation. Three 61R drills were in need of rebuilding or replacement. Bulk ANFO trucks working two shifts per day were unable to match the requirements of the four draglines dne to long travel distances, slow discharge rates and their inability to load water-resistant products into the increasing number of wet holes. This paper outlines the significant steps taken to introduce new equipment and technology and the resulting improvements in the mine's productivity and economics.

Jan 1, 1986

By P Hartlieb, M Noeger, M Varelija

Rock bolts are important in underground mining as they provide support to the rock mass around the excavation. They are the most common reinforcement method in mining and civil engineering excavations. The length of the bolts, types and spacing between them can be varied, depending on the reinforcement requirements and the use case (Kolapo, Onifade and Praise, 2022). The rock bolt provides safety and stability for the rock mass in the excavation area and they can be mechanically anchored, grouted, or friction anchored. They normally don’t have a measurement option and there is a possibility that it failed without showing visible signs on the surface, especially in grouted rebar bolts where they can still have some residual strength. Therefore, support functionality can be lost without recognising it. To overcome that, sensors can be installed on all three previously mentioned bolt systems. Intelligent bolts with implemented measuring systems have a function of showing changes and indicating if there is some damage on the bolt. So, it can be said that intelligent rock bolts are regular bolts equipped with additional instruments which are helping us detect potential instabilities inside of the rock mass or malfunction of the bolt itself. Changes in rock mass can be tracked, by measuring rock bolt reaction concerning the excavation response. Rock mass damage and instabilities are therefore measured in terms of rock mass deformation. Moreover, other additional information depending on the type of the sensor device could be collected. Based on such measurements, information about rock mass state can be derived. Different rock bolt types work at different reaction principles. Therefore, limitations on sensor application and information that can be extracted must be considered.

Sep 1, 2024

The Mount Whaleback iron ore deposit at Newman, Western Australia comprises the largest known continuous iron ore deposit in Australia, originally with a Measured Resource in excess of 1700 Mt of hematite ore. The deposit occurs within the Hamersley Province which forms part of the Pilbara Block in the NW of Western Australia (Figure 1). The Mount Whaleback iron ore deposit, together with a number of discrete iron ore bearing satellite orebodies in the Newman district, contributes to the Newman Lump and Fines products. Extensive quality control systems are utilised from mining to shipping to ensure that each product meets a narrow geochemical target grade range.

Jan 1, 1997

By Mike Sharwood

This subject is to be discussed in greater depth by Mike Sharwood. It has also been the subject of a mini-symposium by the Melbourne Branch of the AusIMM in October, 1993. The papers from this symposium were distributed to the membership late last year "to raise their consciousness and to promote greater awareness and understanding of the wide range of liabilities that may arise". An introductory paper by Nicholson outlined the many areas in which liability may arise with particular emphasis on expert reports, eg: Takeovers Schemes of arrangement Acquisitions from associates Prospectuses Related party transactions Directors' duties Continuous disclosure Other influences (environmental, occupational health and safety, trade practices)

Jan 1, 1994

By S Carr-Cornish, K Moffat

Social licence to operate is developed and kept through managing both operational impacts and the relationship between local community and company. However, CSIRO research has demonstrated that in determining how accepting community members are of a mining operation, relational factors, such as procedural fairness and trust, are much more important than operational impacts, such as impacts on employment and the environment (Moffat and Zhang, 2015). Companies seek to develop relational factors through their engagement with local community; such engagement has many aspects, including, initially identifying stakeholders and positioning the company as part of the local community (Lacey et al, in prep; Thomson and Boutlier, 2011). These relational factors involve the social identities of people living in the community. Social identities are a part of people that shape their beliefs, based on their connections with various groups in their lives (Hogg et al, 2004).An engagement process, intentionally or not, inevitably interacts with the social identities of stakeholders (Crane and Ruebottom, 2011). For example, traditionally, at the very beginning of engagement processes, community members are assigned to categories using conventional stakeholder mapping and categorisation methods, often based on assumptions about stakeholders’ interests, which equates to assumptions about stakeholders’ social identities (Colvin, Witt and Lacey, 2016; International Council on Mining and Metals, 2012). Yet, there has been limited empirical inquiry into whether such categories reflect the social identities of stakeholders and if there is a bearing on relational factors, including, the perceived fairness of consultations and trust in mining companies (Crane and Ruebottom, 2011). Also at this time, companies commonly seek to create a presence in communities, for example, joining Chambers of Commerce and participating alongside community members. Again, there has been limited empirical inquiry into whether community members and companies identifying with the same overarching group and thus sharing aspects of social identity, influences relational factors (Crane and Ruebottom, 2011). In this study, we examined the effects of changing aspects of social identity by changing how stakeholders were identified and companies were positioned, on how stakeholders’ perceived a new mining operation, specifically how they perceived the procedural fairness of the proposed consultation process and trusted the company, two factors that underlie a company’s social licence to operate.CITATION:Carr-Cornish, S and Moffat, K, 2016. Out of the box – the power of social identities in engagement processes, in Proceedings Life-of-Mine 2016 Conference, pp 180–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By S H. Begg

"*This is an abstract only*Most technical and economic analyses are performed to reduce uncertainty to help make decisions. Decision-making is about ranking alternatives - rarely are precise predictions required, if even possible. This simple observation has profound implications for modelling approaches, how they deal with uncertainty and the reliability of information provided by subject matter experts.CITATION:Begg, S H, 2013. Some reflections on uncertainty, decisions, models and people, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 3-6 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By D Stephenson, N R. Steward

“TerraFlowingTM” is a dewatering process that addresses both the value proposition of Tailings as a Resource™, and the safe storage of tailings. “TerraFlowingTM” incorporates two stages of cyclone dewatering followed by centrifugation of the final dilute tailings stream. In this process three dewatered tailings streams are produced; a primary cyclone underflow, a secondary cyclone underflow and a centrifuge pulp. These three streams can be combined, or used, in various configurations to achieve different outcomes. The ability to vary the cyclone and centrifuge operations and configuration enables this process to deal with tailings feed variations in particle size distribution and mineralogy and deliver consistency, or design variations, in particle size distribution, tailings solids concentrations and recoveries. Water recovery can be up to 85% of the total water in the tailings with a stackable final tailings product achieved if the three tailings streams are combined in the maximum solids concentration configuration. The primary cyclone can be operated to deliver a particle size distribution suitable for tailings storage facility embankment construction or alternatives such as concrete structures or shotcrete for support. The secondary cyclone underflow and centrifuge pulp is suitable for beaching deposition within the tailings storage facility.

Jul 1, 2021

Background A recent development in many industries,' including the mining industry, has been ever increasing acceptance and adoption of extended (12-hour) shifts and compressed work cycles compensated by more time off work by employees between cycles. In the Western Australian mining industry development of `long-distance-commute' (LDC) coincided with adoption of 12-hour rotating shifts. Preludes to LDC were the `construction-style' rosters with two crews plus allowance for annual and sick leave relievers working the statutory 13 consecutive shifts followed by one shift off. Crews rotated day to night shift weekly or at fortnightly intervals. Average hours of 72 to 78 per week were common. The author had personal experience working these rosters in the East Pilbara of Western Australia from 1977 to 1982. Workers tolerated these rosters until a suitable combination of frustration, boredom, despair and the `Five Grand Fever' triggered them to `pull the pin' and head for relaxation in Bangkok, Manila, Nimbin, or Margaret River according to their personal tastes.

Jan 1, 1996

By C Xu, B Li

Multi-sensor fusion visual perception technology significantly enhances visual perception capabilities in complex and harsh environments by combining visual data from different sensors. This technology is especially useful for scenarios where traditional single visible light sensors, such as standard cameras, struggle due to poor lighting, adverse visual conditions, or other visual obstructions. In environments with low light, smoke, or dust, the performance of conventional visible light sensors degrades, limiting their application. By integrating data from various sensors like radar, infrared thermal imaging, and others, multi-sensor fusion technology provides a more comprehensive and complementary visual solution. This fusion not only enhances the robustness of visual systems but also greatly expands their potential applications in fields like visual surveillance. In recent years, deep learning methods have become the mainstream technology for addressing multi-sensor fusion issues, demonstrating significant advantages in adaptive feature selection compared to traditional machine learning methods. However, deep learning-based multi-sensor fusion algorithms still face several challenges. The design of network structures is often redundant, lacking effective screening of useful components within multimodal information. Mainstream fusion algorithms focus excessively on improving display effects without adequately considering the needs of downstream applications and tasks. Existing fusion perception algorithms are generally designed for open visual scenes and lack targeted design for complex visual degradation factors present in tunnel environments of mines. Current deep learning methods for designing multi-sensor fusion networks heavily rely on manual experience to create fusion modules. This reliance increases the complexity of network design and can lead to redundancy. Redundant network modules are difficult to identify in end-to-end learning tasks at this stage, significantly slowing down network inference and potentially interfering with the output of fusion perception. Additionally, training these fusion modules typically requires large amounts of well-annotated multimodal data, further increasing implementation difficulty and cost. For instance, the fusion network design proposed by Li and Wu (2018) focuses on extracting multimodal fusion features, while Zhao et al (2020) introduced a feature decomposition mechanism in the feature fusion and extraction modules. Researchers like Zhang and Ma (2021), Xu et al (2020), and Liu et al (2017) have attempted to improve network structures through dense cascades and the introduction of residual connections. Although these methods have improved the handling of multimodal information to some extent, they still face limitations in distinguishing between useful and redundant information, with redundancy persisting in network designs. Ideally, the design of fusion networks should be more intelligent, guiding network structure design heuristically based on the importance of different modal information for the current task. This would reduce information redundancy and network weights, requiring the development of new algorithms or frameworks capable of automatically identifying and optimising fusion strategies, thereby reducing dependence on manual experience while improving fusion efficiency and network performance. Current deep learning designs for multi-sensor fusion algorithms often overlook the

Sep 1, 2024

By Frfas C, Parrilla F, Regife J. M

A project to develop the Zinclor electrowinning cell to industrial size is being conducted at Tecnicas Reunidas' Research and Development Centre with Spanish Ministry of Industry support. This project is the final development phase in zinc electrowinning from a chloride medium, the highest ZINCLOR technology development level prior to the industrial scale having already been reached. This paper covers the outcomes and conclusions corresponding to project Phases 1 and 2: Process Selection and Industrial Electrodes (1 m2) design and testing. The most important achievement reached is that there are presently available industrial cathodes and anodes for the Zinclor diaphragm cell giving an optimum response for zinc chloride electrowinning with unit power consumptions between 2.65 and 2.80 kWh/kg Zn, depending on the diaphragm type. Standard electrolysis conditions were: 65 g/L ZnC12, 3 g/L HCl, 160 g/L NaCl, 350 g/t Zn arabig gum as the addition agent, 36¦C, and 400 A/m2 current density. The selection of electrodes, diaphragms and organic additives for the industrial scale tests have been optimised. The complete electrowinning cell development, with electrodes having an active area of I m2, enables the evaluation of Zinclor Technology application for industrial processes.

Jan 1, 1993