Search Documents

THE MORWELL BROWN COAL DEPOSITSTHIS deposits of brown coal in the neighbourhood of Morwell, are of tertiary age, and are represented on several horizons, but, owing to lack of evidence, the exact age cannot be fixed definitely. It is chiefly by reference to the basalt flows of the Older Volcanic series that the brown coal beds have been classified as of Pre-Volcanic and of Post-Volcanic age. The Pre-Volcanic brown coals are less widely distributed, and the seams generally are thin, though near Thorpdale a thickness of 40 tt. has been recorded, and from 10 ft. to 12 ft. in the vicinity of Narracan. Both of these localities lie to the south-west of Yallourn, and it has not been proven as yet whether these older coals and accompanying basaltic flows pass under the Morwell beds.The brown coal deposits have accumulated in an area where extensive faulting in early tertiary times has taken place with oscillations of elevation and depression of the land surface. In the vicinity of Yallourn, Paheozoic strata (probably Silurian) are exposed on either bank of the Latrobe River about a mile above the powerhouse weir, where the river flows through steep banks rising a couple of hundred feet on either side. The Silurian strata are highly inclined, and consist mostly of slates and Illudstones. Resting unconformably on the upturned edges of the Silurian is a conglomerate bed of Mesozoic age, above which occur beds clipping to the south-east of felspathic sandstones, with alternating mudstones at times carbonaceous, and containing thin seams of black coal.The brown coal seams and associated lignitic Clays, sands, gravels, etc, rest on the Mesozoic strata (as proved in the vicinity of the power-house and by boring north of the Latrobe River, near the old open cut), but do not appear on the surface of the Mesozoic, where these beds attain an altitude of more than 50 ft. above the present level of the Latrobe River.Half a mile upstream from the power-house a layer of basalt of the Older Volcanic series, almost resting upon the Silurian strata, is...

Jan 1, 1924

The first 12 m diameter rakeless thickener in the Australian gold mining industry was installed to treat plant tailings at the St Ives gold plant in April 2000. The plant processes approximately 3.2 M tonnes of ore producing about 430 000 oz of gold per annum using conventional crushing, grinding, gravity and carbon in pulp processing methods.The main benefit sought from the thickener was to improve water recovery in the plant and provide water for a 55 000 oz per annum heap leach operation. The thickener design indicated that more than 128 m3/h of overflow water could be returned directly into the plantÆs water circuit, relieving the demand on the borefields. The resultant surplus in the water circuit would then be available for the heap leach project. Based on laboratory and pilot plant scale tests conducted by EIMCO the thickener was designed to handle up to 700 m3/h of tailings slurry (450 tph of solids) with a 40 per cent oxide component in the ore blend. The normal plant throughput is 565 m3/h of slurry (400 tph of solids). Gold mineralisation in most areas at St Ives comprises quartz-sulphide vein and breccia lodes with common albite-biotite-chlorite alteration assemblages. There are well developed supergene gold horizons in the clay-oxide profile above most of the deposits (Osborne, 2002). This results in a wide variety of ore types being treated. At times 40 - 50 per cent of the ore may be oxide in nature. After some commissioning difficulties associated with instrumentation, the thickener has performed satisfactorily although it has not reached its design capacity. The maximum density achieved under normal operating conditions with 20 per cent oxide ore is about two per cent below the design. The thickenerÆs performance deteriorates further with increasing amounts of oxide ore in the blend. The thickener has provided sufficient water for the successful operation of the heap leach and has also provided some down stream benefits for the gold plant by way of pH and cyanide conditioned thickener overflow water.

Jan 1, 2002

Tin mining has taken place in the New England region of New South Wales since 1872. Until fairly recent times there was little pro- vision made for environmental protection. Mining methods,which included ground sluicing and open cutting,had considerable environmental impact. Much of the topsoil was lost and there is little vegetation on the infertile and at times toxic, subsoil. Thus much of the lands disturbed by mining have not been stabilised and are eroding, causing extensive pollution of adjacent watercourses. There are more than 1500ha of abandoned tin mine sites in the New England, representing one of the worst rehabilitation problems in New South Wales and reflecting poorly on the mining industry as a whole. Recent tin mining operations incorporate progressive rehabilitation in their mining cycle. Topsoil is stockpiled and later respread. This topsoil contains a seed source, facilitating revegetation and thus stabilisation. The tin mining industry, under considerable cost pressures at present, is seeking a cost- effective revegetation technique. Most of the mines in the New England are situated in a forest environment. Trials have been conducted in the past using exotic pasture species with limited success due to the characteristics of the subsoil. Other revege- tation trials have used pine or eucalypt tree species. The cost of these techniques is a major disadvantage. Certain acacias species were observed colonising disturbed tin mining areas on very infertile subsoils. Acacias have a number of characteristics indicating a possible applic- ations in mine rehabilitation programmes.

Jan 1, 1987

By J Galvin

This paper addresses the actions of the Australian mining industry, its regulators and educational providers towards ensuring that a pool of competent mine managers is maintained in Australia and that mine management remains a desirable career path for future mining professionals. The Australian and global mining industries are experiencing an acute skills shortage. Mine managers, traditionally drawn from the ranks of mining engineers, are at the sharp end of this shortage. Exacerbating the shortage is a perception that a professional mine manager is not an attractive career option. This perception is influenced by the following forces which combine to make the role of a modern mine manager very demanding:legislative requirements for owners and managers to ensure (guarantee) the safety and health of employees; an increasing trend towards prosecution over exposure to risks to health and safety a need to be more aware and responsive to community and environment; financial, technical and æpeopleÆ pressures traditionally associated with the job of managing a mine; and mine management roles being filled by younger and less experienced professionals. Universities and other educational providers have the challenge of both ensuring that undergraduates are exposed to these issues during their study and continuing to promote mine management as a desirable career option. Anecdotal and statistical evidence indicates that young graduates are choosing and remaining in technical roles rather than taking on the challenge of mine management. Furthermore, it is suspected that the issues referred to above are contributing to the low retention rate of young professionals at mine sites. The challenges are not insurmountable, however. This paper reviews the initiatives of industry, the regulators and educational institutions in addressing these challenges. It includes a focus on:prosecution policies and their impacts, tertiary education program content and delivery modes, CPD initiatives of the Mine Managers Association of Australia, and alternative pathways for obtaining mine management qualifications.

Jan 1, 2006

Based upon specialised experience of rope mechanics spanning over 20 years, this paper reviews the processes of degradation and fatigue that are relevant to hoisting ropes in mines. The review is brought up to date with an account of the most recent work in this field, which identifies a torsional fatigue process and quantifies the impact of degradation upon the residual service life. A proper understanding of these processes is important in determining how different parameters of hoist design and operation interact to determine rope life. This knowledge is also important in informing decisions relating to rope discard based upon observed condition, as well is identifying the critical features that must be quantified reliably during inspection.

Jan 1, 2005

Pilot plant work has played a major role in the process development and design phase of the Iscor Heavy Minerals project. The pilot plant campaigns have been aimed at three process areas, namely primary beneficiation (wet gravity circuits), heavy mineral separation and ilmenite smelting. A process development structure was put in place, and the various pilot plants designed and built. A number of pilot campaigns were conducted during the project phase since 1995, and most of the key objectives were achieved. Various other valuable ælessonsÆ were learnt, and were incorporated in the full-scale plant designs, or used to change operating philosophies, equipment choices et cetera. The cost and durations of the pilot runs were significant, and an analysis indicated that the major risk and technology area of smelting has contributed more than 70 per cent of the total cost.

Jan 1, 2001

By D C. S M, J Skudder, R F. Sandenbergh

Metallic sulfide minerals present in most gold ores, Morila gold ore included, often decompose under typical gold leaching conditions. The reactions and their products consume oxygen and sodium cyanide, consequently competing for oxygen and cyanide used in gold dissolution. The resultant effect is to reduce both the kinetics of gold dissolution and overall extraction efficiencies. The present paper discusses results obtained from plant data analysis and laboratory work investigating the problem of higher than expected consumption of sodium cyanide at Morila Mine Gold Plant. Cyanide consumption at the Morila Mine Gold Plant had been consistently running at 46 per cent higher than the expected value without any corresponding increase in gold recovery. In fact, plant data analysis showed an inverse relationship between cyanide consumption and grind, as well as cyanide consumption and gold recovery. Experimental and plant data analysis indicated that better control of the [CN-]/[O2] ratio is necessary for the efficient use of reagents and achievement of higher gold recoveries. Careful control of this ratio at a minimum of eight enabled the reduction of sodium cyanide consumption by 200 g/t, that is, from 650 g/t to 450 g/t. Coupling these experimental conditions with the addition of lead nitrate at 100 g/t improved the overall gold recovery to 93 per cent compared to the average plant recovery of 90.2 per cent over a six-month period. This improvement was also reflected in the leaching kinetics where 70 per cent gold extraction was achieved after four hours, as compared to 59 per cent in the absence of lead nitrate addition. Also of great importance is the fact that the combination of hydrogen peroxide and oxygen gave inferior performance relative to either of the two reagents used separately. This scenario presents an opportunity for excluding hydrogen peroxide, an expensive reagent, and focusing on improving the oxygen addition system to boost dissolved oxygen concentration in the plant.

Jan 1, 2007

By Y Peng, D J. Bradshaw, X Chen

At NewcrestÆs Telfer gold mine, a strategy of regrinding pyrite rougher flotation concentrates has been proposed to increase gold recovery and reduce cyanide consumption in the CIL circuit. The regrinding will be followed by an additional copper/gold flotation stage, where copper minerals need to be separated from pyrite. However, although the minerals are well liberated, the separation of chalcopyrite from pyrite in the cleaner stage is not always straightforward. The surfaces of the fine particles, produced during regrinding, are more easily oxidised and contaminated than coarse particles, directly influencing the particle floatability. The depression of pyrite is difficult in the cleaner stage as well due to copper activation, a process which is also highly dependent on the grinding environment. In this study, different grinding media, including mild steel and stainless steel, was used in the regrinding to produce different regrinding chemistry, such as, pH, Eh, and iron hydroxide contamination. The effects of regrinding conditions on chalcopyrite flotation and its separation from pyrite were studied. It was found that the stainless steel grinding media, which produced an oxidising environment, was more beneficial for the separation of chalcopyrite from pyrite after regrinding. The mild steel grinding media had a detrimental effect on both chalcopyrite and pyrite flotation. This study addresses the importance of choosing suitable regrinding conditions in the pyrite and copper flotation circuit.CITATION:Chen, X, Peng, Y and Bradshaw, D J, 2012. Effect of regrinding conditions on the flotation of chalcopyrite and its separation from pyrite in the cleaner stage, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Ketelaar P. B, Nichols S, Power W. L, Utley D. C

The impact computers are having in geoscience is distinctly mixed. In the petroleum industry where much of the data are based on geophysics, computers have become an integral part of exploration and reservoir evaluation and simulation. In the minerals industry, the trend to computerisation is more advanced in some disciplines than others. Geophysical and remote sensing data are routinely processed and imaged using state of the art computer techniques. Mine surveying, planning, design and resource and ore reserve estimation are now all predominantly reliant on computers. However senior management of many companies, particularly in the mineral exploration industry, are still reticent to fully embrace the technology. 3D computer modelling of geology and orebody delineation is still largely in its infancy. Two current and significant drawbacks to the routine use of computer modelling of geology in both mining and exploration are the tedious and time consuming modelling process and the lack of seamless interaction between 3D computer-aided drafting (CAD) software and geographical information systems (GIS) which are largely 2D in their data treatment. There is an urgent need for a 3D spatial information system (eg 3D GIS) with intelligent and rapid modelling functionality. One of the keys to the successful building of 3D geological computer models begins with data base structure and design to ensure that there is no loss of data fidelity through data capture, storage, manipulation and modelling. Once a model is constructed, the latest generations of visualisation software provide sophisticated environments over a range of hardware platforms for visualisation in both mono and stereo viewing. This is demonstrated by the geological models which are presented in the digital interactive version of this talk whose URL on the World Wide Web is: http://www.ned.dem.csiro.au/FRACTAL/pubs/talk97AUSIMM/

Jan 1, 1997

By J-P Franzidis

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMCÆs (now BHP BillitonÆs) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007

By R Balusu, P Humphries

In combination with detailed field studies and goaf gas characterisation, computational fluid dynamics (CFD) models have been used to develop optimum and effective strategies for inertisation during longwall sealing operations to achieve goaf inertisation within a few hours of panel seal-off operation. This study has combined detailed analysis of the performance of various inertisation field trials together with CFD modelling results of different inertisation operations in order to develop the optimum inertisation strategies. A number of parametric studies were conducted on the base case CFD models that had been calibrated and validated based on the information obtained from previous inertisation studies and goaf gas monitoring. These studies included changes in inert gas injection locations, inert gas flow rates, seam gradients, and different inertisation strategies to investigate their effect on goaf inertisation. Studies indicate that the strategy of inert gas injection through the MG seal was not as effective as the alternative strategy of inert gas injection at 200 m behind the face. Innovative inertisation strategies have been developed and subsequently implemented at an underground coal mine in Australia. Further investigations have been carried out in the development and demonstration of proactive inertisation strategies with the objective to suppress the occurrence of spontaneous heatings in active longwall faces, in particular under unexpected scenarios such as during slow retreat/face stoppage due to difficult geological conditions. Initial trials at two Australian longwall panels have demonstrated the great potential of this practice to contain the onset of heatings in the goaf.

Jan 1, 2005

By S P. Suthers, J M. F Clout, J J. Campbe

An advanced technique for modelling hydrocyclone separation performance has been developed. This technique is based on the combined modelling of hydrocycloning parameters and ævirtualÆ iron ore feed. The virtual feed modelling was performed using a novel (in-house) software package called æRecognitionÆ, which uses data from optical image analysis to classify the particles in certain size fractions according to total iron content and calculates data for every grade class. These data include the average mineral composition and density of every liberation class in every size fraction. This information about every size fraction, representing the ævirtual feedÆ, was input to the mineral processing modelling package USIM PAC. The hydrocycloning process was then modelled for this virtual feed using the Plitt hydrocyclone model. Empirical calibration coefficients for the hydrocyclone model were calculated using an optimisation procedure in Excel. Pilot-scale hydrocyclone beneficiation experiments were performed on an iron ore blend, using different hydrocyclone pressures and per cent solids in the feed pulp. These experiments were modelled and the modelling results were compared with the experimental results. The new modelling approach enables prediction of the recovery of each mineral in the products, calculation of the total iron grade and recovery, and optimisation of iron ore beneficiation using hydrocyclones.

Jan 1, 2005

By Kolarczyk M

When controlling the ventilation process in a deep mine some knowledge of the sensitivity of the air volume output to changes in the resistances of network side branches is of great advantage.Sensitivity is taken to mean the limit of the differential quotient AV /ART where AV. is the change in air output in the i--h side branch caused by a change of resistance LI R in the r-th side branch. A method Is presen- ted for determining any arbitrary co- lumn of the sensitivity matrix. A network interpretation of this met- hod was developed in which an ancilla- ry network additional the basic network is constructed and solved, giving an analysis of the sensitivity signs de- pending on the structure of the network.

Jan 1, 1988

By K Baskaran, T McKenzie

Sustainability is becoming increasingly important in the mining and mineral processing industries and must incorporate the associated waste products. Acid mine drainage (AMD) is one such by-product and is one of the most serious environmental problems facing the minerals industry today. The oxidation of sulphidic mine wastes often continues for a substantial period of time after mine closure, resulting in difficult and costly remediation and rehabilitation works. Mining companies are often reluctant to spend increasing amounts of money on waste treatment when the mine life is limited or even finished. Hence a simple, low maintenance and low-cost method of treating AMD is required. Whilst this paper does not address the issue of AMD, it does propose methods for removal of individual species from AMD with potential benefits, including raising AMD pH. A novel concept of using biosolids as a biological adsorbent, or æbiosorbentÆ, of metals from AMD is being investigated at a laboratory/pilot scale level. Biosolids are a by-product resulting from the biological treatment of wastewater, and have been previously shown to adsorb metals from aqueous solutions. This could lead to an environmentally sustainable or ægreenÆ method for treating both AMD discharges and disposing/reusing the biosolids. The result of a laboratory-scale study of the biosorption of Zn(II) is presented in this paper. Physical parameters including reaction kinetics, mixing speed and solution pH were investigated. Solution pH also rose an average of 2 pH units over the 24 hour equilibrium time û a valuable side effect when treating acid mine drainage. The outcome of the study highlights the usefulness of biosolids as a biosorbent for the removal/recovery of metal ions from acid mine drainage. A simple, low-cost treatment technology requiring low maintenance would be beneficial to the mining industry to address some issues relating to AMD and would help integrate environmental and economic considerations into sustainable environmental management.

Jan 1, 2002

By D S. Scovira

The effect of blast vibration on highwall stability is a common concern for many open pit mines. Vibration in such a case is a typical near-field blast vibration situation. Vibration modelling in the near-field of a blast requires consideration of both the amplitude and frequency attenuation of waveforms with distance. Most existing blast vibration models are designed for far-field vibration and do not simulate the frequency attenuation and its effect on waveform shape. With the advent of electronic detonators it is desirable to quantify the effects of blast delay on the amplitude as well as the frequency of blast vibrations. A suitable modelling tool is proposed here. At present, a blast vibration model with double attenuations(amplitude and frequency) has been developed at Orica. The present model simulates the amplitude and frequency attenuations separately using different transfer functions. The amplitude attenuation is modelled according to the non-linear relation between the peak particle velocity (PPV) and the charge weight scaled distance established from the signature hole vibration. The frequency attenuation is modelled with the signal broadening based on KjartanssonÆs transfer function û a linear model for attenuation of waves. The model is capable of taking multiple sets of signature waveforms as input to improve the modelling accuracy of the wave propagation in the geology at a site. The screening effect of the earlier firing holes in the path of a later firing hole is taken into account on not only the amplitude, but also frequency attenuation. The present blast vibration model is suitable for modelling both near-field and far-field blast vibrations. It yields reasonable agreement with measured field data for the near-field vibration examples discussed.

Jan 1, 2007

By K Osman, P Bennett

The mining of an underground orebody requires development both in waste and ore before stoping commences. Regardless of what metal is being extracted, the waste development is minimised to reduce the cost per unit of metal mined. At the Western Metals Zinc Kapok mine site, reducing the cost per tonne of lead and zinc mined is paramount. Decline waste development costs can be minimised by methods such as increased gradient or reduced drive size. Ore development will also involve some mining of waste. The degree to which waste mining can be minimised will depend on the thickness and dip of the orebody. The drive geometry will also determine the percentage of waste within the face. It is by mining methods such as resue mining that selective mining may be used to maximise the amount of metal mined and reduce waste dilution. Resue mining can be used around a set of selection criteria established by the mine site. These selection criteria will determine how resue mining can be applied to the mine site. Selection criteria include firing times, number of headings available, acceptance criteria for percentage lost metal, dilution and most importantly operator acceptance. The single pass or two pass resue mining method should be chosen depending on the site acceptance criteria and selection criteria. The Western Metals Zinc Kapok mine site has established a set of parameters which accept the two pass resue mining method for the mining of the ore drives. The blasting results from a single pass resue method were reviewed during more recent trials in a single heading. Through a comparison of results, the parameters allowed the decision to determine the applicability of resue mining and its current form to Kapok. This paper outlines the parameters set by the Kapok mine site, reviews these in relation to the two forms of resue mining and examines the criteria which make this mining method applicable for Western Metals Zinc.

Jan 1, 2002

A modular computer-based monitoring system for mines is dis-cussed. The system consists of the following modules : production moni-toring system HADES, methane monitoring system CMC, seismoacoustic and seismometric systems SAK and SYLOK, communication systems. The system enables one to compose flexible,` economic structures according to the specification of a mine. Application of microcomputer-based monitoring and control systems in coal preparation plants also is discussed.

Jan 1, 1985

The Burragorang Valley lies approx. 95 km by road south west of Sydney and some 35 km west of Camden. It is over 80 km in length and varies in width from 3 km to over 16 km. Geologically, the history of the Burragorang Valley is of interest. It was referred to by early geographers and N.R.M.A. booklets as the largest sunken valley in Australia. This description is incorrect as it is a water worn valley formed by the dissection of an uplift in the south western portion of the large Sydney Sedimentary Basin. Ages2 ago there extended right across the Blue Mountains, a continuous tableland into which the Nattai, Wollondilly and Cox's Rivers have carved out the formation of the Burragorang. This dissection together with other valleys such as the Megalong, Jamieson and Grose, formed part of the eastward drainage pattern of the uplifting tableland into the Pacific ocean. The lapse of time since the streams in the Burragorang began their work of erosion can

Jan 1, 1976

This paper reviews some of the factors thought to control the formation of supergene gold in the Pacific and its Rim. Discussion of these should lead to reassessment of the economic potential of many areas. In several parts of the world many gold-bearing veins display rich gold values only in the oxidized zone, whereas beneath the present (or ancient) watertable the unaltered vein commonly holds only sub-economic refractory low grade sulphides or arsenides. In the Eastern Highlands of Australia some of the most spectacular concentrations of - gold have been found at shallow depths. For example, Harper (1918) describes the Canton mine in New South Wales which was stoped over a length of 180 metres from the 45 metre level to the surface. The reef yielded gold at 300 g/t in the upper levels, but became gradually poorer at depth. Present geologists of N.S.W. Geol. Survey, G.R. Mcllveen and B.P.J. Stevens, believe that many similar Australian enrichments were formed between the surface and its ancient water table level during the extended period of weathering in the Eocene or pre-Eocene. They concede, however, that further supergene movement of gold may have occurred since the early Tertiary. Large quantities of Mesozoic supergene gold of extreme fineness (Au 99.7%, Cu +òFe 0.3%; Leibius 1885) was found at Mt. Morgan near the Tropic of Capricorn in Queensland. Lower Jurassic sediments cover part of the gossan in a small depression caused by oxidation and collapse of the Main Pipe, thus showing that the supergene gold is pre-Lower Jurassic (Cornelius, 1968). Because the Lower Jurassic landscape around Mt. Morgan was mature with a surface slope of less than 10 (Playford and Cornelius, 1967), erosion would have been very slow. Moreover, once all sulphides had been removed from the ore body the Lower Jurassic environment would have reverted from highly acid to alkaline as it is at present. Accordingly, gold, goethite and 1. Dept. of Geology & Mineralogy, University of Queensland, St. Lucia, Australia,

Jan 1, 1987

By D Jordan, R Wilmoth, J LeFever

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the US Environmental Protection AgencyÆs, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open Pit Highwalls Demonstration Project. This project is funded by the US Environmental Protection Agency (EPA) and jointly administered by the EPA and the US Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome US, located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 m and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied in situ treatment technologies included: a modified, furfuryl alcohol resin sealant, utilising wood and agricultural by-products to coat the rock surface; EcobondTM ARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface; and two AMD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: ASTM D 5744-96, accelerated weathering of solid materials using a modified humidity cells; mine wall residual wall rinse sampling; microscopy; and core drilling followed by water injection testing. The following paper describes the technologies used for passivation of acid generation from the highwall, the field demonstration, and the testing results from the background and each technology plot.

Jan 1, 2003