Search Documents

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995

By Trutwin W, Tracz J

The outbreak of open fires underground cause disturbances to the conditions of the mine ventilation process. Thermal and chemical effects due to fire create unsteady, transient states in airflow and the spread of combustion products in the mine ventilation network. Changes in airflow have an influence on the fire, constituting a sort of feed-back between the fire and the ventilation process. This paper deals with a numerical simulation method, which enables the determination of transients caused by fires. The mathematical model, of the simulation method considered, has been based upon a: simple model of combustion of fuel in the airway, unsteady exchange of heat between the fire, airflow and surrounding rocks, airflow in mine ventilation networks and the theory of heatflow in the rocks. Initial and boundary conditions allow the determination of a set of parameters describing the airflow, the propagation of combustion products, the tempera- ture of the fire and flow etc. due to the fire. The simulation method, facilitates a graphical presentation of the spread of combustion products throughout the network. The simulation method has been prepared for an IBM PC/AT Computer.

Jan 1, 1988

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By Paine G. G

The measurement of the fragmentation size distribution of a blast muckpile can be achieved directly by screening the entire muckpile. Screening of muckpiles in a production operation is generally not practical due to the logistics and time involved moving large volumes of rock through a screening plant. An indirect technique to assess blast fragmentation size distributions has been developed. This technique uses photographs of the blast muckpile taken at intervals during the excavation cycle. The images from the photographs are input to desktop computer software via a digitiser tablet. The software compilates the rock fragment sizes and calculates a size distribution. This paper discusses the technique and subsequent data analysis. Examples of the application of this technique for the assessment of comparative blast performance are given.

Jan 1, 1990

This paper details a proposal for integrating the use of the Pilbara Iron Ore Classification (PIOC) and stratigraphic data for fine tuning blast. pattern design on Mt Whaleback. The main thrust of the proposal is based on the assertion from Haqan and Harries (1979) that rock properties influence blasting results more than explosive properties. This premise is supported by a literature search, which indicated that blasthole burden, spacing, stemming and subdepth lengths are also determined by rock properties if the same explosive and blasthole diameters are used. A brief explanation of the PIOC is provided during which it is noted that the classification is based on physical hardness, mineralogical and genetic characteristics of the ore. The classification also extends to the two main waste rock types LBIF (banded iron-formation) and shale]. Ore type plans produced from face mapping indicate that many areas on Mt Whaleback can be divided into various PIOC zones and regions thus making it more useful in blast pattern design. Several recommendations for blast pattern design experimentation are made for hard, medium and soft ores as well as for the waste rocks, the most important being the use of expanded patterns to blast. soft BIF and medium hard to soft shales.

Jan 1, 1986

By Meunier G, Davis J, Koperski G

The dry processing of mineral sands concentrates can result in the generation of significant amounts of airborne dust. The radioactive component of this dust has implications within the context of work environment health codes. The last four years have seen considerable investment in dry plant equipment enclosure and dust extraction systems, with resultant reductions in plant ambient dust levels. Simultaneously, an industry wide program was started to examine the origin, nature, mineralogy and radioactivity of the airborne dust. The major findings of this study have been: ò confirmation that monazite was the only significant source of dust radioactivity. ò recognition of two sources of dust: - agglomerates of finely divided ilmenite-rutile alteration products, which are formed by the removal of surface coatings and particles. - abraded mineral fragments, which reflect the mineralogy of the parent particles.

Jan 1, 1991

By Whiten WJ

A method that allows data to be mass balanced and screen models to be fitted in a single step is described. The inclusion of several variables to describe the feed data in the fitting procedure allows a mass balance to be conducted at the same time as the fitting of the screen model. Analysis of Groote Eylandt Mining Company screening data has demonstrated that this method is ideally suited to applications where complete stream data are not available. Also, certain random fluctuations in screen model parameters arising from the fitting of consecutive mass balances and screening models are significantly reduced. A cubic spline function with fixed knot positions corresponding to particle sizes and variable (fitted) cumulative percent passing values is used to describe the feed size distribution. When the spline function is interpolated at the experimental feed particle sizes a fitted feed size distribution is obtained. This feed size distribution is then used as input to the screen model calculations from which product size distributions are generated. Since both feed and product size distribution data are used to minimise the residual errors between the observed and fitted stream size distributions, a mass balance is Conducted simultaneously with the screen model parameter fitting.

Jan 1, 1984

By Weining L

In-situ experiments were performed in a tunnel built in loess soil with the displace- ment components of the tunnel lining and the acceleration components of the tracks measured during the passing of trains. The measured parameters were then studied by the spectral method. As a result, the dynamic forces of trains was simulated numerically and a deter- ministic dynamic nonlinear analysis was carried out by means of finite element method. The results obtained by two different approaches were in fair coincidence. Results of the study indicate, that the low and medium frequency components of the dynamic train loading would be crucial for the dynamic responses of the tunnel lining and surrounding mass, and their effects would increase with the speed of passing trains within a certain range.

Jan 1, 1987

By F A. Rosyid

Mineral resources are national assets which must be capitalised for national development. Those assets should be transferred into real economic capital and then into social capital to achieve national/regional prosperity. Successful development in the mining industry will depend on the correctness in determining the role of mining industries for regional development. Using the context of sustainable development, this paper will analyse the concept and process of mining industry development as an accelerator to achieve regional sustainable development, using the mining operations of PT Newmont Nusa Tenggara (PT NNT) in Batuhijau, Sumbawa Barat Regency as a case study. In the premining activity phase, Sumbawa Barat was dependent on the agricultural sector. Agriculture contributed around 40 per cent of the regional gross domestic product (GDP). Meanwhile, in the activity phase, mining became the sector with the biggest contribution to regional economy. From its operation in Batuhijau, PT NNT contributed around 70 per cent of the regional GDP per year since 2001. In year 2000, the GDP had increased 170 per cent from its figure in 1999. However, due to its depleting reserve, PT NNT will finish its activity in Batuhijau by year 2015. Consequently, the Government of Sumbawa Barat Regency must develop other sectors in the post-mining phase to sustain economic development. Based on location quotient (LQ) and input-output analyses, Sumbawa Barat should develop its priority sectors, ie agriculture, trading and hotel, services and construction to achieve sustainability after mining life. Development of these non-mineral sectors is expected to sustain economic growth in the region.

Jan 1, 2008

By Henderson N, Schaap H

In large companies with mining operations spread over multiple sites, it is essential that consistency between sites is maintained in preparing and classifying resource and reserve estimates. The endorsement by The AusLMM and AMIC of the "Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves" and the subsequent incorporation of reference to the code into the ASX listing rules for mining companies has provided a basis for the consistent classification of resources and reserves. However, compliance with other criteria more or less stringent than the Australasian Code can present some reporting difficulties. Examples include listing requirements for foreign stock exchanges, particular Acts of Parliament that may apply to individual leases, constraints imposed by individual companies on their own leases, and ultimately, reserves for short, medium and long term planning. Confusion can arise when any two or more sets of reserves for the same lease are compared.. To alleviate this confusion, a standardised procedure was developed for the calculation and classification of coal resources and reserves. The procedure which is geostatistically based incorporates a technique called "Irregular Block Kriging" where specific mining blocks are directly kriged. The procedure has enabled those engineers and geologists with only a basic understanding of geostatistics to apply the technique and not feel hampered by some of the complex mathematics which in the past has tended to inhibit and overcomplicate the use of geostatistics. The procedure has resulted in "cleaner" data bases and hence more reliable reserve estimates.

Jan 1, 1990

By Brockway DJ, Holmes RJ

A natural gamma-ray gauge has been devel- oped for discriminating overburden and inter- seam sediment from low ash coal located on a moving conveyor belt. It is based on the difference in natural radioactivity of the sediment and overburden compared with the low ash coal, which is detected with a highly ef- ficient "Polyscin" NaI(T1) gamma-ray detector located underneath the conveyor. Gauges have been successfully installed on the bucket wheel boom of the two coal dredgers at the Loy Yang Open Cut. They are used to warn dredger operators that they are digging overburden or sediment and that action is required to avoid the sediment or divert it to the waste dump rather than send it to the coal bunkers at the power station.

Jan 1, 1987

It may at first sight appear somewhat presumptuous for the writer to attempt to discuss a subject in which he cannot pretend to possess any special scientific training; but a sufficient apology can surely be found in the fact that a very large percentage of the accidents from explosives occurring in metalliferous mines is traceable to the ignorance of the characteristics of these compounds by the miners who have to handle them, and to their deliberate disobedience of the rules laid down for their guidance by the manufacturers, the government regulations, or the special rules of the mines.The only method which promises any possibility of improvement upon these conditions is to substitute reason and understanding for the rule-of-thumb principle which says "you should do this" or "you should not do that." In the one case his own knowledge and intelligence enables the miner to avoid any dangerous practice in the other his inclination prompts him to do anything which will save time, provided he is not found out or at best trusting to his memory to tell him what is dangerous, without the reasoning which makes that memory easy.Another evil of rule-of-thumb knowledge is that, from its very nature, it prevents adaptability, and so we find that old miners, who learnt blasting in the days of black powder, cannot understand why high explosives do not require heavy tamping, or because copper bars are permitted in tamping powder they should not be used with other explosives...

Jan 1, 1903

By Childs G, Ritchie IC

This paper describes the principle and operation of small hydrocyclones for use in the coal, minerals and other process industries. The principles for selecting a hydrocyclone for an application are also discussed. Typic- al uses and installations in various industries are described.

Jan 1, 1984

This paper is a summary of the general theory of sampling published by the author in 1975. Sampling is a random process and its the- ory is a study of the, numerous errors liable to take place in the course of its realization. A complete sampling scheme is a sequence of sampling (proper) and preparation stages . At each stage, the total error ET is the sum of : -.Sampling errors EE arising from the selection process itself. -Preparation errors EZ arising from the operations (crushing, transfer...) sup- ported by the sampled material. ET a EE + EZ . At each sampling stage, the (total) sampling error EE is the sum of seven inde- pendent errors : - Weighting error ED resulting from the non-uniformity of the density or rate-of-flow of the sampled material. - Integration error EI1 resulting from the long-range distribution heterogeneity of the sampled material. - Periodicity error EI3 resulting even- tually from periodic quality variations of the sampled material.

Jan 1, 1976

By J M. Palin

Hydrothermal scheelite precipitated in fault-veins at Paradise, Bonnie Jean, Davidson's and Glenorchy mines display chemical variability involving REE patterns that are transitional between two end-member types. Type I is a MREE-enriched pattern with no or a small positive Eu anomaly. Type II is a flat to MREE-depleted pattern with a strong positive Eu anomaly. The chemical inhomogeneity of these scheelites can be explained by a model of fractional precipitation of REE, with preferential removal of MREE from the fluid during precipitation of scheelite. Irrespective of the mechanism responsible for scheelite precipitation, the source of dissolved constituents is different for scheelites from the Paradise Mine. Bonnie Jean, Davidson's and Glenorchy scheelites formed from LREE-enriched fluids whereas Paradise scheelites precipitated from fluids that were lower in LREE. These inferred fluid characteristics cannot be linked unambiguously to specific source rocks in the region, but could suggest that scheelite deposited in the Paradise fault-vein reflects a more mafic source of REE possibly greenschists, whereas the REE in scheelite from the other mines suggest a more felsic source.

Jan 1, 2003

It is a well known fact that the best method of rock reinforcement is to avoid physical ground support. This goal can be achieved by means of: - Increasing the rock structural strength - Geological definition and forecasting. - Sequencing the excavation - Smooth blasting In many cases however, extra ground support is needed in order to maintain safe working conditions. In an open pit, the structural strength of rock cannot be increased by lowering the pit walls due to economical reasons. Economy demands steeper walls and less waste to be hauled to the dump. The geological conditions can also often be extremely poor and unpredictable. For excavation sequencing and smooth blasting there are good possi- bilities, such as cleaning of the pit walls after the main excavation, arul- ing of long small diameter straight inclined holes, use of smooth blasting techniques and lightened explosives.

Jan 1, 1989

By T P. Hynes

Submarine tailings disposal is conceptually an attractive option for managing reactive mine wastes in coastal regions by virtue of reduced sulfide oxidation under a water cover and no infrastructure to maintain after mine closure. However, the lack of detailed knowledge of metal leaching, dispersal of fine tailings and biological impacts in the marine environment has led to no operating permits currently in effect in Canada. Detailed chemical and ecotoxicological assessments at two historic copper mine sites (Little Bay and Tilt Cove) in the north coast of Newfoundland with tailings disposed in an estuarine to shallow (=100 m) marine environment have demonstrated reduced reactivity of sulfidic tailings when submerged under water. Only non-acute toxicity is detected in biota inhabiting the immediate vicinity (A review of another historic shallow marine tailings operation in the southern tip of Vancouver Island (Jordon River) with a high-energy setting also reveals problems with unconfined tailings dispersal and temporal biological impacts. Documented studies at two deeper (140 - 360 m) marine tailings disposal operations at the northern tip of Vancouver Island (Island Copper) and northwestern coast of British Columbia (Kitsault) again illustrate imperfect predictions of tailings re-suspension and dispersal. At these sites, bioaccumulation of tailings-derived metals appears to be minimal. There is evidence of rapid re-colonisation of the tailings surface by benthos but of different species than the original population. Integrating these observations with reported metal fluxes and biological diversity associated with submarine hydrothermal vents, the risks and benefits of deep-sea (>1 km) tailings disposal are discussed. To determine if submarine tailings disposal in deep, confined basins on the seafloor is environmentally friendly, detailed multi-disciplinary research incorporating physical, chemical, biological and toxicological components will be indispensable.

Jan 1, 2003

The subject of octanes and knock in petrol engines is of general interest, not only to the engineers and chemists in the petroleum and automotive industries, but also to the motorist who wishes to see some light through the haze of propaganda regarding "super" petrols. A mixture of petrol vapour and air will explode when a spark is passed through it if it contains more than one and a half per cent. or less than six per cent. of petrol vapour by volume. In a petrol engine the mixture has to be within the explosive range before it will operate. When the spark is passed it 'ignites the petrol vapour-air mixture which burns with rapid but finite progress of the flame front 'through the unburnt gases in much the same manner that a charge of dynamite is consumed. The turbulence of the gases in the cylinder under normal operating conditions more than doubles the velocity of the flame front and enables the combustion to be completed by the end of the working (expansion) stroke:KNOCKIf the cylinder head 'is poorly designed or is covered with a deposit of carbon, it is possible for "hot spots" to develop, and these can ignite the mixture before the spark is passed. This pre-ignition gives rise to an engine knock but is accompanied by a dull thud rather than the ringing knock associated with the true "knocking" found in a petrol engine and attributed to the detonation of the mixture. Until a few years ago it was thought that this detonation was due to a shock wave produced by the rapid combustion of the mixture, and sufficiently intense to cause ignition of...

Jan 1, 1951

By Pinghui J

The paper describes the detailed hydrogeological studies carried out prior to the sinking of twin shafts at British Coal's new mine at Asfordby, Leicestershire, UK. The test methods for assessing potential groundwater inflows to the shafts are discussed and details are given of the ground freezing scheme employed through the major aquifer zone in the Sherwood Sandstone at a depth of 375 metres. During shaft sinking pressure recovery tests were carried out to further assess potential inflows and the results are compared with those from the surface tests prior to sinking.

Jan 1, 1988

By Bell LC

Overburden removal, mining and reclamation are now accepted as the basic operational steps involved in the winning of coal by open cut methods. To attain the lowest operational cost, the recontouring and revegetation of spoilpiles must be planned concurrently with the planning of overburden removal and mining. The earthworks associated with reclamation work on spoilpiles often account for 75 - 90 per cent of total reclamation costs. Experience at Callide Mine has shown that the way that spoilpiles are contoured does influence water retention and can reduce erosion from rainfall run-off. However, provided the recontoured slopes meet'Mines Department specifications, the quality of reclamation work is judged not by the quality of the earthworks but by the plant regrowth on the reshaped surface. Thus it is the quality of the revegetation which is of prime importance. For vegetation to be successful, time must be spent on planned research into methods of overcoming plant nutrient deficiencies and selection of suitable grass and tree species. The research programme undertaken at Callide Mine consists of three stages :- laboratory studies glasshouse trials field trials

Jan 1, 1978