Search Documents

By Kershaw MG

At the Risdon plant of the Electrolytic Zinc Company of Australasia Limited, impurities toxic to the electrolytic production of zinc metal, notably arsenic and antimony, have traditionally been coprecipitated when precipitating iron as ferric hydroxide. With the development of a new lead/zinc mine at Elura, New South Wales, it was anticipated that the concentration of impurities, particularly arsenic, in the zinc sulphide concentrates treated at Risdon would increase. This suggested that an increase in the capacity of the iron purification step in the Risdon plant would be required to cope with the higher input of these impurities.Laboratory investigations showed that the additional capacity would be achieved, either by a massive increase in the amount of iron used as the "collector" in the process, or by a two-stage process. The latter approach was preferred as an increase in the amount of iron precipitated would lead to much higher operating costs and overloading of the existing equipment.

Jan 1, 1985

By Gigmai W

Ok Tedi Mine is a high production open pit porphyry copper mine located high in the Star mountains of Papua New Guinea. The mine produces an average of 160 000 tonnes of ore and waste daily at a 1:1 strip ratio. Full scale drilling and blasting began in 1988, prior to which time all material was ripped and dozed.Drilling and blasting procedures at Ok Tedi underwent a major review commencing mid-1989. As a result of a mutual commitment by management at Ok Tedi and the mines explosives supplier ICI, significant reductions in overall blasting costs have been realised. These cost savings are primarily the result of the introduction of air bags, expanded patterns and better field execution.

Jan 1, 1992

Sluice-boxes are by far the most widely used concentrating devices by small-scale operators in PNG who work alluvial gold deposits. The sluice-box designs and their operating conditions used are known to vary widely. The selection of sluice-box configuration and the operating parameters such as the water flow rate is purely based on past experience. Some use small flowrates to increase the fine gold recovery at the expense of efficient separations and capacity while others use high flow rates resulting in increased fine gold losses but with high throughput rates. Recent work has revealed that the combination of riffle height, their spacing and wash water flow rate are the most important parameters that determine the success or failure of such operations. This combination has been shown to depend on the in situ gold and gangue size distributions of the deposit being processed. This paper describes a design procedure which uses a non-linear optimisation method to determine the optimal combination of the above parameters to maximise the metallurgical efficiency of such operations.

Jan 1, 1993

This paper reviews hydrometallurgical processing technology for refractory gold ores, which form an increasing resource stock for gold. The reasons fQr ore refractoriness and pressure, chemical and biooxidation process options are briefly listed. Electrochemical technology, suitable for processing refractory ore is reviewed and some preliminary results for the electrochemical oxidation of slurried arsenopyrite are given.

Jan 1, 1992

The port of Townsville is situated on the main north/south rail system of the Queens- land Government Railways and is the eastern terminus of the east/west rail link from Towns- ville to Mount Isa. With a stable beef and wool producing area along the east/west rail route, the expanding mineral industry development at its western end and the continuing growth of the Townsville region the administrators of the port are continually'keeping abreast and ahead of port development to ensure an effective and economic growth of port facilities to meet the needs of the area served by Townsville.

Jan 1, 1974

And it takes more than good organisation. You may read or heard this poignant reflection: We tried hard, but it seemed that every time we were beginning to form up in teams we would be reorganised. I was to learn later in life that we tend to meet any new situation by re-organising, and a wonderful method this is for creating the illusion of progress while producing confusion, inefficiency, and demoralisation This was written by the Roman Gaius Petronius in AD65. How much have things changed in nearly 2,000 years? What then does it take besides the fundamentals and good organisation to build a successful career in a successful organisation? I'm prepared to venture a list of what I'll'call Tips for Young Professionals. If you've got what it takes, and apply these, I think that you'll gain a great deal of satisfaction from your career, even if you don't reach the distant target each of you should have in mind now. So settle back in an advice-receiving mode, and please forgive me if I come across as a master of the bleedin' obvious, as Basil once accused his wife Sybil of being in the unforgettable Fawlty Towers.

Jan 1, 1990

The paper examines the possibility of applying the monolithic packing technique developed in the UK to the division of wide development drivages in Australia, so enabling double entries for longwall retreat panels to be created from shortwall units. The monolithic pack of the UK therefore becomes a monolithic partition in this proposed Australian application. A method developed for the analysis of the load development in packs installed behind longwall advancing faces is adapted and used to predict the support performance of the monolithic partition. Conclusions are made regarding partition construction and possible rates of advance.

Jan 1, 1986

The reliable estimation of ore reserves in mineral sand deposits depends on drilling methods and assay techniques that have been specially developed within the industry. Improvement of these techniques is a continuing process, as variations within and between deposits are highlighted during the actual mining operation. Constant monitoring of metallurgical losses along with mineral production allows comparison of mineral tonnages accounted for by mining, with original calculated reserves. A review of ore reserves in the Jerusalem Creek field from scout drilling in the sixties, through mining in the seventies, shows the progression from understatement prior to mining, to the present when more than two thirds of the reserves have been depleted.

Jan 1, 1979

By Madgwick J. C

Bacterial leaching of museum grade chalcopyrite and chalcopyrite concentrates at low sorptive relative humidities (55-91 per cent rH) was demonstrated. Optimum release rates were 13 and 27 mg/gram/100 days copper (Cu++) at 91 per cent and 80 per cent rH and 12 and 33 mg/gram/100 days iron (Fe++) at 80 per cent and 73 per cent rH for concentrate and "pure" chalcopyrite respectively. The optimum copper release rates occurred between 73 per cent - 86 per cent rH and 30-40 mM acid concentrations. Bacterial copper leaching rates were some twenty times slower for emersed copper concentrates, at low relative humidity, compared with submerged cultures. Bacterial copper solubilization was almost quantitatively inhibited above 150 mM acid levels (< pHO.8).

Jan 1, 1984

By G H. Luttrell

The use of secondary desliming cyclones ahead of froth flotation cells to reject ultrafine (-45 ¦m) particles has become a popular option in the United States for preparing fine coal feeds for froth flotation circuits. In light of this popularity, several experimental studies have been performed at industrial plant sites to develop a better understanding of the impacts of ultrafine desliming on froth cell performance and, ultimately, overall plant performance. These studies included an evaluation of various circuit configurations incorporating different flotation technologies (conventional machines and column cells) as well as different dewatering systems (disc filters, screen-bowl centrifuges, and thermal dryers). The data obtained from these studies indicate that deslime circuits offer several important benefits including lower product ash, reduced product moisture, better froth handling characteristics, and lower capital and operating costs. In addition, case studies conducted as part of this investigation have been used to develop generic guidelines for how deslime circuits may be successfully applied to improve the overall profitability of fine coal flotation circuits for both the metallurgical and steam coal markets.

Jan 1, 2005

The Nelson province was chosen as the prime area for rhenium sampling, based on its mineral associations. Sample preparation involved benefication by grinding and flotation. A modification of published procedures for rhenium analysis was developed and the results compared with those obtained for molybdenum on the same samples using atomic absorption spectroscopy. The results of the analysis for both metals is discussed and the relationships between rhenium and the molybdenum mineralisation of this region is commented on. A metallogenic province is defined for molybdenum and rhenium and the tectonic setting for this is discussed. Some consideration has been given to rhenium possibilities in Fiordland and the Coromandel Range.

Jan 1, 1980

By Kerr M. H, Slaughter P. J

Design of the new cemented hydraulic fill plant was based mainly on experience with a succession of previous fill plants. Two stage cycloning of combined concentrator tailings was introduced. Design of the two stage cyclone configuration was assisted by computer simulation of cyclone performance. Cementing additives, namely Portland cement and ground copper reverberatory furnace slag, drawn from bulk storage, are pre-slurried prior to mixing with hydraulic fill. Quality control of fill being sent under- ground is achieved by a series of automatic control loops. Plant instrumentation was given prime consideration during the design phase. Inventory checks of all mass flow metering equipment are made at regular intervals. Fill is pumped to boreholes at several locations. Details of the equipment and operating procedures for the plant are Discussed.

Jan 1, 1973

By Van Rooyen F

An introductory review of the current grade control blasting techniques (selective mining strategies) used in the Eastern Goldfields has recently been undertaken. The survey was initiated and conducted by the Western Australian School of Mines. Four distinct selective mining strategies have been identified and a number of trends have been highlighted. Many operations, however, have developed techniques which use a hybrid method to suit the site conditions. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and experiences no mixing of the various identified ore and waste blocks and is fully reco- vered at the minimum overall operating cost. Due to this unified aim all of the grade control blasting techniques have many common design Features.

Jan 1, 1988

By Bhattacharyya A. K

A strata parameter is introduced to include the deformation characteristics of the undermined strata in the prediction of subsidence movement. By using the strata parameter and mining factors as parameters, a nomogram for predicting the maximu

Jan 1, 1994

By Paine G

Kidston Gold Mines commenced mining in 1984 and currently mine approximately 10 million tonnes per annum of ore and waste using a conventional truck and shovel open pit method. The overall mine grade is a low 1.82 grams per tonne.The mineralisation is generally uniform within the ore zones and mining boundaries are staked out from blasthole assays according to pre-determined cut-off grades. Buffer blasting is necessary to minimise post-blast lateral movement of in-situ grade for digging control.The characteristics of the rock currently mined vary widely from soft oxidised to hard unweathered rocks. Blasting problems have been experienced during the initial mining phase in these harder rocks.

Jan 1, 1986

This paper compares and evaluates the impact of income tax and value-added tax on the decision to explore for minerals or to develop a mine in four countries: Australia, Papua New Guinea, Argentina and Indonesia. Three aspects are considered in depth:- domestic tax rules applicable to mining projects;- taxation of foreign mining investment and foreign providers of expertise;- taxation of project finance (other than equity) from foreign sources.Specific tax issues discussed include tax deductibility of various costs, treatment of tax losses, special tax incentives, comparative treatment of various corporate structures, non-resident withholding taxes, and tax costs of various forms of project finance. The paper also illustrates the comparative impact of income tax on rates of return by means of a simulation of a mining project in each of the four countries. The simulation demonstrates why the highest rate of return may be obtained in Argentina and the lowest in Australia.Relevant features of the income tax systems in each country (at 15 February 1990) are summarized and compared in several tables annexed to the naner.

Jan 1, 1990

Diesel-engine exhaust emissions represent a concern to the mining industry due to the poten- tially harmful health effects of the pollutants, as well as high costs associated with providing proper ventilation to assure a healthful working environment. The control of exhaust emissions is complex since the operating mode and condi- tion of the engine, the mine environment, and the operator's skills all influence the concen- tration and composition of the emissions. It is not practical to measure each exhaust pollutant in underground mines; therefore, a monitoring methodology is required to measure the pollut- ants and assess the air quality.

Jan 1, 1988

The liquid products of low-temperature carbonisation of coal are of variable composition, very much influenced by the rank and type of coal, and process parameters. In general the tar contains a high proportion of phenols and a low proportion of bases. The neutral oil is more analogous to a thermally cracked petroleum oil than to a high temperature tar. Present practice and possible future trends in the production of chemicals and liquid fuels from low temperature tar are reviewed in the light of recent work on the detailed composition of the tar The phenols and aromatics will probably continue to be of most value, with the bases a useful source of spec- ialty products. However the high aliphatic content of the neutral oil (particularly 1-olefins and n-paraffins) is bound to receive more attention for chemicals as well as for liquid Fuels.

Jan 1, 1969

Coal mining safety and health legislation is more than typical of safety legislation which has been born of adversity. Indeed, in the main it has been the child of disaster. Requirements which now appear obvious were indeed only occasioned by either social injustice or more commonly by great disasters. Even then changes were often made only after months or years of deliberation by committees. Early mining legislation in New South Wales benefited from the experience in Great Britain. The pioneers of our industry were miners from there and brought with them the basic British legislation, so we started with knowledge gained the hard way. A review of accidents statistics provides a measure of the effectiveness of mine safety legislation, but unfortunately rules cannot control human nature. Miners, managers and inspectors must work as a team to make mines safe and new legislation in New South Wales is planned to this end.

Jan 1, 1975

By M E. Malmstr÷m

Quantification of site-specific sulfide oxidation rates is crucial to accuracy of prediction of, for example, the environmental impact of a mine site. Sulfide oxidation reactions are reportedly increased by bacterial mediation; determination of abiotic and biotic weathering rates thus requires the establishment of sterile control samples. However, sterilisation often involves exposure of samples to extreme conditions that may alter the physical, chemical, or mineralogical characteristics of the tailings and hence affect element release rates. The impact of various sterilisation techniques, common and novel, on the element release rates from tailings from the Kristineberg site, northern Sweden, has been investigated. Batch weathering experiments indicated that the different methods of sterilisation (autoclaving, heat treatment, ethanol/heat treatment, application of antibiotics, rinsing with distilled water, and γ-radiation) did not greatly affect long-term element release rates. Long-term experiments (>30 days) are thus to be recommended for establishment of weathering rates. Sterilised and untreated control samples showed similar element release rates after ~100 days of experiments; possible explanations include that microbial oxidation is not important under our experimental conditions (Po2 = 0.2 atm, pH ~2.3, 22¦C, 0.01 M HNO3, no additional nutrients).

Jan 1, 2003