Search Documents

By Wright J

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

By B Siddall, A Gunstone

The use of a partial secondary crushing circuit provides a flexible way to optimise existing SAG comminution circuits limited by rock competency or enables optimal processing of an ore through second hand equipment not specifically selected for that ore. This paper details the process involved in designing a partial secondary crushing circuit using the recent installation at Mt Rawdon Gold Mine in Queensland as an example.

Jan 1, 2004

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995

Market forces, particularly iron ore prices, demand that plant operators achieve higher throughput in the worldÆs iron ore beneficiation plants without compromising yields or efficiency. This means that production cost per ton is of paramount importance and that all major pieces of Processing Equipment have come under close scrutiny to improve throughput at their most efficient performance levels and for the longest possible continuous running time. Without doubt the use of modern engineering standards and materials of construction has contributed to matching these throughput, efficiency and availability demands. However, often not enough attention is paid to the so called æinsignificant elementsÆ connecting this metallurgical equipment, such as chutes, pipes or other conveying systems, and particularly to the sufficient protection of their wearing surfaces. The result can be an unplanned and expensive outage caused by the wear related failure of such components. This paper will discuss:the theory of wear and the multiple factors of material and design that contribute to a reduction in wear; and the combinations of modern wear resistant materials available to todayÆs engineer and how, by intelligent selection and correct application, plant availability can be optimised. Examples outlining how these principles have been applied in South Africa showing some improvements leading to increased plant availability.

Jan 1, 2002

By Snowdowne J. B H

Rand Mines, Limited, located in Johannesburg, Republic of South Africa has recently completed feasibility studies which have lead to the initiation of two major coal strip mining ventures. A minicomputer based mine planning system was developed to perform the feasibility studies. The broad approach of this system is to utilise inter.-actively the specialist skills and interpretative abilities of mining engineers and geologists. This paper reports briefly on the outline of the system and at greater length upon certain aspects of its use.

Jan 1, 1977

By McAllister J

Oxygen was in restricted use at Port Kembla until tonnage oxygen became available for steelmaking in the open hearth furnaces. In adopting the new process various modifications to furnace design and operation were necessary and some of these, including increase in roof height and variation in firing and draft control, are discussed.The design of oxygen lances is also discussed and various steelmakingtechniques considered.Steel production increased with oxygen roof lancing-one- furnace producing 8,507 tons in one week-but new problems, such as rate of refractory wear, and disposal of fumes, were created.Design of future open hearth oxygen furnaces is predicted.INTRODUCTIONIn the post-war era, the availability of "tonnage" oxygen caused a major revolution in steelmaking techniques. Various pneumatic processes showed that steel can be madeat a very fast rate and that oxygen steelmaking can be applied to open hearth furnaces. Methods used are surface impingement with roof lances, bath injection with door lances, flame enrichment with fuel firing, mixed gas and oxygen firing, and enrichment of normal combustion air by oxygen injection into the flue systems.Owing to its previous restricted availability and high cost, oxygen was used in rather small quantities in the open hearth furnaces at Australian Iron and Steel Pty. Ltd.(A.I. & S.), Port Kembla, until about the middle of 1960.At that time tonnage oxygen became available and roof lancing commenced on No. 33 furnace at No. 2' open hearth shop.

Jan 1, 1962

By Marois R, Hauff P, Kowalyczk P, Lipton G, Bedell R, Neville R, Edmundo G, Ehling M, Kern R

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the Short Wave Infrared range of the solar spectrum from 1220 to 2420nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a Quartz- Sericite-Pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

By Kurihara K, Tanimoto C

Construction and mining sites are often subject to unexpected flooding and extensive delays may occur in locating and installing emergency pumps. This particularly applies to sites located in remote areas. A simple and effective pump, called an air-lift pump, can be built from the equipment available at the working site. The basic req- uirements are a compressed air supply, air hose and conventional water pipes. The air-lift pump is comparatively in- efficient but approximately 35 per cent of the available compressed air power at the site can be applied to pumping. Suprisingly high liquid discharge rates may be obtained in suitable applications. The theoretical and practical consider- ations of the air-lift pump are evaluated and a suggested procedure for the emergency design and construction is outlined. INTRODUCTION. Sudden inundations of water into mine and development excavations require the immediate removal of the water if extensive and often irrepairable damage is to be avoided. Pumps installed in shafts or tunnels may become un- servicable due to being totally submerged during the flooding. The emphasis is on rapid

Jan 1, 1976

By Gray J, Krouse HR, Changkakoti A, Kwak TAP

The Dachang tin field with more than one hundred million tonnes of ore at 1% tin and 3% Zn is one of the largest tin fields in the world. It comprises five carbonate replacement tin deposits, of which the Changpo deposit containing about 80 million tonnes of ore at about 1% tin is the largest deposit. The deposit, hosted by middle Devonian limestone, argillaceous limestone and black shale, is genetically related to the Longxianggei granite.The oxygen, hydrogen and carbon isotope data of minerals, rocks and fluids suggest a magmatic fluid which evolved during the crystallization of the Longxianggei granite. Mass balance calculations show that the depletions observed in 180 and 13C values of calcites from the ore bodies to the country rocks were due to continous isotopic exchange reactions between the magmatic fluid and the marine limestones at different W/R ratios and between 300 and 600¦C.

Jan 1, 1990

By Partridge A. C

Pinched Sluices, in a variety of guises, are used extensively for the separation of minerals according to density. In the authors' work a pilot-scale sluice has been constructed with provision for splitting the discharge stream into a number of layers. The composition and flowrate of the stream can thus be analysed as a function of depth and the results presented graphically. The effects of such parameters as total flowrate, pulp composition and particle size on overall performance can be clearly seen from such data.

Jan 1, 1979

By Aziz N. I

Examination of the geology and support performance at two site leads to development of an under tanding of the influence of caving on powered support rating. The two site represent the current extremes in support rating, i.e. 6/260 tonne supports operating in the Hirst seam at Solsgirth Colliery, Scotland, and 4/900 tonne supports operating in the Bulli seam, West Cliff Colliery, Australia.A conceptual model considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata.The caving mechanisms identified for the strata of the Hirst and Bulli seams, are different. These mechanisms being related to rock properties - the palaegeography and depositional conditions at each site-produce caved wastes with different yield characteristics.An analysis of the results obtained for convergence and support reaction during production cycles at both sites shows the manner in which support reaction is developed, indicating the importance of higher setting load densities in the Bulli seam.Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations the powered support and the caved waste immediately behind the powered support - further demonstrates the influence of caving mechanisms on support rating.

Jan 1, 1989

By Polthier K

A short discussion of the salient aspects of a dispersed flow model in relation to the gas flow in blast furnaces is given. The use of the theory in assessing vessel performance is mentioned. Tracer results of a blast furnace (688 m3) from three furnace levels and different radial positions are analysed and results presented as D/ud values. The significance of the shapes of experimental tracer curves are included and comparison is made with results obtained on other furnaces.

Jan 1, 1975

By M T Roche

The Cannington deposit is one of the largest accumulations of silver-lead known. Located 135 km southeast of Cloncurry in North West Queensland (Figure 1), Australia, the deposit is currently in the feasibility stage of its development. The deposit is named after the nearby Cannington Pastoral Property which runs some 25 000 sheep on 'downs' country. The investigations of the Cannington deposit are carried out under the authority of Mineral Development Licences 139 and 144 and Exploration Permit for Minerals 6788, Answer Downs. Exploration for Broken Hill Type (BHT) silver-lead-zinc deposits in the Mt Isa region has been undertaken by The Broken Hill Proprietary Company Limited's Minerals Division (BHPM) since the early 1980s following in-house research which showed that the Eastern Succession of the Mt Isa Block exhibits characteristics which were favourable for hosting BHT

Jan 1, 1994

By B J. Monaghan, P Zulli, X F. Dong

In the lower zone of blast furnace (BF), slag trickles down through a packed bed of carbonaceous particles in the form of films, rivulets or droplets. During its downward flow, there are significant interactions occurring between slag and other phases, ie gas and packing particles. In particular, the interaction between gas and slag is closely associated with the key flow phenomena such as loading, flooding or channelling in the lower zone of the BF. With gas introduced laterally through tuyeres and slag flowing downward from the cohesive zone to the hearth, this interaction varies throughout the lower zone and in the cohesive zone:  strong cross-flow of gas relative to the slag occurs in front of the raceway  counter-current flow of gas and slag occurs in the upper parts of the lower zone  both strong cross- and counter-current flow of gas and slag around and within the cohesive zone. These interactions can be linked to furnace irregularities, affecting smooth operation and limiting production. Therefore, understanding the gas-slag interaction and its influencing factors remains critical for BF process control. In the current review, the physical behaviour and key influencing factors of gas and slag flow are initially examined. Numerical models describing gas and slag flows in a packed bed at micro-, mesoand macro-scopic levels, are reviewed. Each simulation approach has its advantages and limitations, as well as unique assumptions when used in BF process modelling. Applications of these approaches to gas-slag flow in key identified functional zones will highlight the differences between approaches and modelling outcomes. As no single approach can fully address all aspects of gasslag interactions, an integration of different approaches is considered an effective and beneficial method in providing a more complete understanding of gas-slag flow in the BF process.

Jun 19, 2024

By G Showers, R Triglavcanin

The complexity of understanding the whole thickening process to achieve real performance improvements cannot be underestimated. The last significant change in feedwell design was more than 15 years ago with the introduction of self-dilution systems û firstly with OutotecÆs Autodil, followed by FLSmidthÆs E-Duc. Now, following many years of extensive in-house research, including close collaboration with AMIRA and the CSIRO, Outotec has launched the next generation Vane Feedwell. The Vane Feedwell has been globally patented and installed at various sites. This paper briefly outlines the feedwellÆs development using CFD modelling and its subsequent performance in a æreal lifeÆ site installation. Plant results of the first commercial Vane Feedwell, in a mineral sands application, are discussed. The Vane Feedwell was retrofitted so comparative data of pre- and post-installation is shown.

Jan 1, 2009

The Bendigo goldfield is centred on the urban area of Bendigo (population approximately 60 000) in central Victoria, 130 km north west of Melbourne, Australia. Gold was discovered at Bendigo in 1851 and production continued through to 1954. The Bendigo goldfield is the second largest goldfield in total gold produced in Australia, after KalgoorlieÆs Golden Mile with a total production of 22 million oz. The geology of the Bendigo Field consists of a series of tightly folded, interbedded sandstone and shale sediments. Within the sediments the gold mineralisation is hosted in quartz reefs or ribbons closely associated with anticline axes and reverse faulting. The gold within the quartz reefs is typically both coarse grained and erratically distributed.

Jan 1, 2002

By Cox I

Raiseboring is a technique that has become popular in modem mining engineering since the early 1960s. A study has been undertaken at the University of Queensland to determine important factors affecting the optimum diameter of raisebored shafts, excluding local parameters such as the maximwn excavation size that a particular rock type can safely accommodate.This model is used to examine each of these factors and the results indicate that the optimum diameter for raisebored shafts is generally between four and six metres.

Jan 1, 1991

By Kajioka H, Nakamura Y

Na2CO3 is a powerful flux for both dephosphorization and desulphurization in oxidizing atmospheres. In order to study refining with Na2CO3 and the nature of the Na2CO3 slag itself, hot metal (4Kg) was melted in Al203 crucibles in a high frequency induction furnace and oxidised with oxygen under Na2CO3 slag. The behaviour of Na2CO3 at high temperature was observed by thermobalance. It was found that dephosphorization ceases in a few minutes and [,P] after refining is easily lowered to less than 0.010%. [%P] after refining is affected by [Si], [P] of hot metal, the refining temperature and the consumption of Na2CO3. Desulphurization also ceases in a few minutes but it shows curious behaviour, increase of [S], decrease of (S) and increase in sulphur lost, during the latter half of run. [%S] after refining is also affected by [P] of hot metal, the refining temperature and the consumption of Na2C03o

Jan 1, 1980

China has abundant bauxite resources, but these resources are mostly of a diaspore, which has a feature of low Al2O3 to SiO2 mass ratio, typically ranging from four to six. Compared to other materials, this kind of raw materials consumes more alkaline and energy in the process of metallurgy, and incurred a high alumina production cost. To solve this problem, researchers in China have done a lot of work on removing of the silicon from bauxite. Under the impetus of these works, in 2003, the first flotation plant of diasporic bauxite in the world was constructed in Zhongzhou, Henan, China. Seven years of operating experience shows that this technology can signifi cantly reduce the costs of following-metallurgy processing. These efforts are an important reference for the processing of similar resource. In general, for Western scholars it is diffi cult to fully understand these works because most of them are published in Chinese. In this paper, a detail introduction for the research progress on China bauxite de-silica flotation was presented, these works involved crystal chemistry, wettability of bauxite minerals, collector and modifi er in bauxite fl otation and flotation practice, etc.

Sep 13, 2010

By G Johnson, S Michalek, N Redman

As the modification of the 2009 Mill OperatorsÆ Conference theme from æmilling through the boomÆ to æthe boom û experience gained and lessons learnedÆ exemplifies, comminution practitioners are facing a series of challenges in the dramatically changing mining environment. One of the main problems plant managers have been facing during the boom times has been the severe metallurgy skills shortage and high staff turnover, both factors that can cause difficulties in mill liner management. Many of todayÆs mill managers are now also more than ever faced with the need for cost-cutting in order to continue operating viably. Amongst other potential target outcomes such as maximised throughput, MillMapperÖ, a tool for mill condition monitoring and mill performance optimisation, can be utilised to address these issues. This paper demonstrates how MillMapperÆs quantifying decision making tools can serve to be in control of managing mill liner and production issues, and how it can form the basis for mill cost savings without the risks normally associated with conventional methods or the lack of using any condition monitoring methods. MillMapperÖ is currently being referred to at a rate of approximately 150 surveys and associated reports per annum at processing plants in Australasia, South America and Africa. Examples throughout the paper provide insight into how the presented sample set of users have extracted benefits that could have otherwise not been safely or at all achieved.

Jan 1, 2009