Search Documents

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

By Z W. Orndorff

Excavation through sulfidic geologic materials during construction activities has resulted in acid rock drainage (ARD) related problems at numerous (>40) locations across all five geologic regions of Virginia, USA. Potential acidities ranging from >100 to develop a statewide sulfidic materials risk map; document ARD impacts to soil and water quality and engineered structures; and develop methods to assess site-specific risk potentials within a given highway corridor. A statewide sulfidic materials GIS risk map was developed based upon the state digital geology map which assigned four levels of relative risk to all mapped strata based upon predicted lime requirements and probabilities of encountering highly reactive materials. Non-highway construction activities have also routinely disturbed sulfidic materials, and a recent airport project in northern Virginia resulted in over 150 ha of extremely acidic (pH 45 mg/L) run-off from this site heavily damaged a receiving stream, partially due to the fact that it dissolved the galvanised steel water control structures in stormwater detention basins, leading to direct discharge of run-off and sulfidic sediments. The airport area was treated and revegetated in 2002 with a combination of lime-stabilised biosolids, straw mulch, and acid-tolerant grasses. Water quality in a receiving second-order stream quickly responded to the treatment, but some release of N was also noted as a secondary effect. Collectively, these results point out the importance of accurately assessing the potential for excavation of sulfidic materials in construction environments, and the necessity of developing toxic materials handling strategies similar to those employed in mining environments.

Jan 1, 2003

By J White

The Eyre Peninsula (EP) has been known for its iron ore for more than a century. Edward John Eyre noted the ironstone outcrop at what is now Iron Knob in the 19th century. Sir Douglas Mawson visited and reported on the geology of the lower EP in 1906, noting the widespread presence of iron stone and the likelihood of copper being associated with the iron stone. Despite this knowledge there has been only one successful iron ore mining region developed on the EP and that is Iron Knob and the Middleback Ranges which have been mined continuously since 1899. The Middleback Ranges can justly lay claim to be birth place of the Australian iron ore and steel industries.The discovery of large scale haematite resources in Western Australia meant that there was no need to seek out iron ore that needed benefi ciation. The low price of iron ore precluded further development of the EP and many other areas in Australia and overseas. This situation changed rapidly in the mid-2000s with the emergence of China as the world’s industrial power house and the soaring demand and price for many resources including iron ore. This triggered a flurry of activity across Australia and led to the rapid exploration and drives to develop the EP iron ore. A brief examination of the magnetic maps of the EP shows the wide spread presence of magnetite and associated smaller haematite deposits. A closer look reveals the magnetite deposits to vary in formation style and host rock lithology as well as being significantly altered by regional metamorphism. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By J Purandare, D Murdoch

The goal of the life-of-mine plan is to ensure that while the site is left safe, stable and non-polluting, the landscape is such that optimal use can be made of the site post-mining and closure. However, in the face of evolving shareholder expectations and the current international economic climate, numerous mines are ceasing operations and moving into a care and maintenance phase. These changes bring with them a high degree of community concern, not only about the potential legacy of closed operations, but also those mines that continue to operate.While mines across Australia are committed from the earliest planning stage to develop clearly defined post-mining land use and landform objectives, broader expectations related to these objectives may change and evolve during the life of the operation. This is especially the case where a mining operation has a project approval where the land use objectives are aligned to land capability and land use commensurate to that which occurred premining. CITATION:Murdoch, D and Purandare, J, 2016. Optimising land for beneficial use during and after mining, in Proceedings Life-of-Mine 2016 Conference, pp 166–167 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R Pax

Feed ore variability, the major disturbance into a mineral processing plant receives considerable attention operationally, and at research and strategic levels to ensure that the throughput of the ore are maintained at all times whilst encouraging a sustainable approach to recovering the valuable minerals from ore bodies. Effort and insights from mineralogical and processing characterisation (eg. ore hardness) of sub-ore body domains allows sequencing for processing to ensure consistency and throughput for the size sensitive grinding unit processes. Optimising the blast fragmentation has benefit as does pre-concentration using ore sorting. Blending of ore domains with different characteristics is common for operations. In recent years a number of technologies have become available for on-line and more rapid assessment of ore and have been discussed in a recent paper by Cameron et.al. (2016) as an opportunity for further utilisation of mine-to-mill (and mine to product) strategies. Current concepts have focused on extensive characterisation of ores so that current control practices can be realised and made more effective with relatively slow measurements and actuation. CITATION: Pax, R, 2018. Dynamic concepts for mine to mill operation and optimisation, in Proceedings Complex Orebodies Conference 2018, pp 124–125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By S Withell, K Sheehan

Whitehaven Coal (WHC) is undergoing a transformative journey, deeply committed to the principles of a High Reliability Organisation (HRO) and the establishment of a mature, interdependent culture founded on psychological safety. This ongoing commitment is not merely aspirational but is supported by performance improvements backed by both quantitative performance data and qualitative evidence of cultural progression. WHC has strategically integrated leading and lagging indicators to target fatal risk. WHC focus areas include an emphasis on strategy and risk appetite, targeted data, informed learning, proactive addressing of fatal risk and the integration of data management and technology.

Apr 16, 2024

By A Goldstone, M Fitzpatrick

Contemporary mine wastewater flows are subject to stringent water quality standards before discharge to local waterways. Strict criteria are often applied as a result of fears of extensive acid mine drainage; a feature of the many abandoned mine adits around the Coromandel, Central Otago, and the West Coast. In most cases the USEPA water quality criteria have been used to set treated wastewater discharge water quality standards. In future it is possible that the recently published ANZECC water quality criteria guidelines will be used for this purpose. The ANZECC guidelines also provide for the establishment of discharge criteria at specific sites, rather than accept the trigger values. The use of site-specific criteria for treated wastewater mine discharges was pioneered at the Golden Cross gold mine, near Waihi, in the late 1980s. The procedure used to derive water quality criteria was based on USEPA guidelines. In developing the Golden Cross criteria, only species that occur, or are similar to those that occur in the Waitekauri River were used. The mine commenced discharge of treated wastewater in 1991, and macroinvertebrate communities in the vicinity of the discharge point have been regularly monitored twice a year for the past 12 years. Despite fluctuations in community composition and abundance over that period, no permanent significant changes in the macroinvertebrate communities occurred between sites above and below the treated wastewater discharge. The success of the site-specific criteria at Golden Cross has shown how the application of this methodology can result in the protection of aquatic life while allowing for the discharge of treated mine wastewater.

Jan 1, 2003

THE manufacture of Portland cement on a commercial basis dates back to the year 1824, when Joseph Aspidin, of Leeds, patented his process. It was, however, only within the past 25 years that the cement of to-day commenced its history, and during that period manufacturers have constantly tried to improve the grade of cement.The introduction of the rotary kiln at the opening of this century was the starting point of rapid development in the process of manufacture, and in the quality of the cement produced.Following on the rotary innovation came the wet process. This at first was used only where the raw materials were of a soft nature; but to-day nearly all classes of materials can be treated by this method. Oompared with the dry process, it allows for greater refinement of raw materials, more intimate mixing, better chemical combination, and economy in fuel. Taking advantage of this, the manufacturers in England and America are in a number of cases substituting the wet for the dry process.Subsidiary machinery throughout the factories, such as crushing and grinding mills, have also been vastly improved. The chemists, too, have done their share in the work. Long and careful research has proved the necessity for accurate proportioning of raw materials, thorough mixing, and very careful burning. All these factors combined have given us the product of to-day, which is consistent within very narrow limits, and far superior to that of the beginning of this cement era.

Jan 1, 1926

By A Scott

Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data û especially with semi-automated data acquisition by instrumented mine equipment. However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model. An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc not only have many areas of interest but also have very different conceptual models by which they evaluate performance. It is too ambitious to attempt to bring all of these cultures together û in a single step. However, the success of the Mine to MillTM project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from orebody model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling. However, in both cases the data collected is strongly focused on the technical requirements û not on the business model. This paper considers how to define at least some of the key decision points in terms of some case studies. Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning.

Jan 1, 2002

Iron from the blast furnace constitutes the starting point in steel production and any increase that can be made in iron production will bring about important repercussions in a long line of processes. Coke constitutes a major item in furnace operation and consumption at the Port Kembla Works of Australian Iron & Steel Ltd. has been approximately 1,850 lb. per ton of iron produced on ore practice, or 3,000 tons per day.For many years coke quality has been subject to much criticism by furnace operators throughout the world, sometimes with little real grounds. Whatever the merits of previous arguments, and they were no doubt two-sided, the development of bigger furnaces has focused attention on coke strength. At the same time a decrease in the quantity of good quality coking coals available to many plants has stimulated research in this field.Extensive coke research has been carried out overseas, and in Australia the.B.H.P. Organization is now actively doing likewise in its Central Research Laboratories at Shortland near Newcastle, N.S.W., and works research groups at Newcastle and Port Kembla Steelworks. Similar work has been initiated in the beehive coking industry. Such work is in its infancy and this paper will outline the direction of the activities at Port Kembla rather than propound specific solutions.At Port Kembla good quality coking coals are readily available from the IIIawarra coalfield. The seams generally mined for coking are Bulli and Wongawilli and to a much smaller extent Tongarra. Characteristics of these coals appear in Table 1.

Jan 1, 1958

By G Byrne, A Bowden

There is often a difference in opinion about the allocation of risk in the establishment of mine closure bonds or financial assurances. From the State’s perspective, protection is needed to ensure that the broader community is not left with the liability of properly closing a mine in the event of a default by the mine operator. Such a default might occur where an operator decides to abandon a site, perform incomplete rehabilitation, becomes insolvent or claims limited liability. On the other hand, mine operators who can demonstrate a strong financial position plus a record of social and environmental commitment and performance, argue that there should be some recognition of this in setting a bond that is less than the full cost of early closure. They argue that a mine rehabilitation bond based on the full cost of early closure is overly conservative and ignores the actual risk of the operator being in default. This paper examines an approach that incorporates the risk of default into the establishment of mine closure and rehabilitation bonds. CITATION:Bowden, A and Byrne, G, 2018. Mine closure bonds (financial assurances) – the ‘how much?’ conundrum, in Proceedings Life-of-Mine 2018, pp 32–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By D Zielinski-Nicolson

The emergence of affordable, portable and versatile wireless devices has enabled a new frontier in mine safety equipment. Existing solutions provide methods for tracking personnel and assets in underground mines but are not designed to optimally integrate into existing and emerging systems. Mine management are often required to coordinate primarily independent emergency, personal protective equipment (PPE), tracking and collision avoidance systems from multiple vendors. These systems involve a variety of wireless technologies that require separate integration projects that discourage adopting new services and policies.

May 5, 2022

By C Tomlin, C Gimber

Historically, key closure risks have been studied during operations and then further assessed as cessation of mining approaches. Only in the past couple of decades or so has progressive rehabilitation and closure become an integral part of regulatory frameworks, sustainable mine planning and more recently, new project and development planning. It is now broadly accepted that the best closure outcomes occur when rehabilitation and closure are properly considered upfront, during the early stages of a mine development project and well before mining occurs. Increasingly, regulatory processes are requiring more diligence on early closure planning, often as part of the environmental impact assessment (EIA) and approvals process, rather than later in dedicated closure study phases. There is an opportunity to use the information generated during this phase to make better decisions on project selection, design, mining methodology and all other facets of the mining operation.

Aug 2, 2023

By M Jara, R Nuñez

As the global interest in sustainable energy sources has increased, lithium has emerged as a vital resource, playing a crucial role in the transition towards a cleaner and more efficient economy, but with this comes important challenges, especially associated to health, safety, and environmental matters. So, it is imperative for the lithium industry to prioritise HSE measures to protect workers, environment and surrounding communities. Implementing robust safety protocols and technology helps ensure the sustainability of mining operations and contributes to the overall responsible development of the industry. In this work we present how the Chilean lithium mining industry becomes a safer and more compliant industry using digital transformation (Cochilco, 2018; Bradley et al, 2013; Cabello, 2022).

Apr 16, 2024

By T R. Gibbons, I Grayand

Geotechnically massive strata may lead to a host of problems during longwall mining. These include windblast on initial goaf fall, sudden loadings on powered supports, periodic weightings, fractures that may propagate to surface, and extreme subsidence problems. It is essential to identify these problems prior to mining and to appropriately deal with them. The problem is essentially that the rock mass does not breakup evenly and when it does so it tends to produce large blocks which may suddenly move. The rock types that produce these problems tend to be massive sandstones, massive siltstones and sometimes igneous sills. The fundamental problem with these is that they do not breakup readily. This is because the ratio of stress they are subject to compared to their strength is low. Thus, the shallower mines with lower stresses are more subject to this problem than deep highly stressed ones with similar strength rock.

Nov 29, 2022

By K Sherry, N Shahbazi

Scope 3 emissions are a set of often overlooked indirect greenhouse gas emissions within a company’s value chain and represent the majority of emissions for many sectors. These emissions arise from activities conducted by entities beyond the reporting organisation’s ownership or direct control and are often challenging to calculate. Scope 3 emissions typically encompass purchasing goods and services, transportation and distribution, managing operational waste, downstream processing and utilising sold products. Within the mining sector, scope 3 emissions often constitute a significant portion of the overall carbon footprint. Therefore, these emissions are a significant aspect of the future of sustainable mining. As the journey towards a world committed to achieving Net Zero Emissions has started, the time to spark a transformative conversation in the mining industry has arrived. Consequently, a better knowledge of scope 3 footprints allows organisations to assess their emission mitigation projects against the total carbon impact of their operations and products.

Sep 1, 2024

By J Isarua, R Mabiria

The Ok Tedi copper and gold project, located in the Western Province of Papua New Guinea, commenced operations in 1983. The open cut mine has undergone several significant transformations throughout its project life including changes of ownership, mine life extensions and varying production performance profiles. As of today, the Ok Tedi Mine is a 100 per cent PNG owned company (67 per cent State and 33 per cent Western Province and Communities) and has a life-ofmine plan extending out to about 2032.

May 5, 2022

By D Asahina, T Endo, H Hosono, T Takemura

Changes in the stress field around faults due to the excavation of underground space or the extraction of underground resources induce fault reactivation. To understand the mechanism of fault reactivation, it is important to observe the deformation and sliding processes of the asperities, which is regionally contacted areas at the fault planes. In the laboratory, triaxial compression tests are commonly conducted to reproduce the stress conditions around faults and study their mechanical behaviours. The conventional measurement devices for triaxial compression testing (eg load cells, local deformation transducers, and piezoelectric sensors) uses sensors to measure changes in the physical properties of rocks, but the direct visual information for the sample condition inside the pressure vessel is limited and can only be estimated from the sample after the experiment. We recently developed a direct visual measurement system to observe the slip behaviour of rocks from the inside of the pressure vessel of a triaxial test apparatus. This paper introduces this visual measurement system and presents some preliminary experimental results. The visual measurement system consists of a steel housing with a built-in commercially available digital camera. The triaxial compression tests were conducted to visually observe the sliding behaviour of the pre-cut specimens and to measure its behaviour through the digital image correlation (DIC) method. The captured images and the DIC results show the displacement field of the specimens for different confining pressure. We verified the sliding behaviour and the failure at/around the triangular asperity under at different confining pressure.

Nov 29, 2022

By I Lipton

The existence of metalliferous mineral deposits on the deep-sea floor has been known since manganese nodules were discovered in the Arctic Kara Sea in 1868. Modern exploration to define commercially viable base and precious metal deposits began in the 1970s and gained further momentum in the last decade. High grade deposits have been delineated but investors remain cautious, many considering deep sea mining projects to be riskier than terrestrial projects. This paper compares opportunities and risks presented by terrestrial mining projects with those presented by deep sea mineral deposits (Table 1). The Solwara 1 volcanic-hosted massive Cu-Au-Ag sulphide deposit, the Atlantis II Deeps sedimentary base metal sulphide deposit, and the Mn-Ni-Cu-Co nodule deposits of the north-eastern Pacific Ocean are used as examples. These are advanced deep-sea projects with published Mineral Resource estimates, on the cusp of development. Off-shore diamond mines in Namibia are also considered. These examples provide a basis for comparing exploration and geological uncertainty, the technical risks of proposed mining systems, and the potential environmental and social impacts. CITATION: Lipton, I, 2018. A comparison of opportunity and risk in deep-sea and terrestrial mining projects, in Proceedings Complex Orebodies Conference 2018, pp 102–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By R Morrison, P Walters, B Adair, V Jokovic

‘Grade Engineering<sub>®</sub> is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans as part of a system-view’ (Walters, 2017). Two of these technologies are directly recoverable through screening stages: Natural Deportment and Induced Deportment. The potential for taking advantage of “Natural Deportment” by size following blasting and crushing has been demonstrated for a range of ore types. Simple and low cost screening can in some cases generate a fine product with improved grade and a lower grade oversize which can be directed to leach or to waste. Where an ore body consists of many different ore types, the traditional approach of blending to metal grade will often add to complexity of treatment, which will reduce the effect of “natural deportment” by size.CITATION: Jokovic, V, Walters, P, Adair, B and Morrison, R, 2018. Applying enhanced grade engineering to complex ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 21–23 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018