Search Documents

Agglomeration for Copper Heap Leaching Agglomeration of ore is a method which can be used to eliminate the migration of fine grained particles throughout a leach heap. Without agglomeration, fine ore particles are able to migration within the heap, clogging flow channels and producing large areas where access of the solution is poor. In order to gain the benefits of agglomeration and improve agglomerate strength even further in copper heap leaching, an economical, acid-resistant binder is needed. However, most binders have been used without any systematic reasoning. A set of novel testing methods were developed, including a soak test, percolation flooded columns, and larger long-term leach columns. The soak test compares the degree of breakdown when agglomerates are subjected to an acidic environment. While the percolation flooded columns and larger long-term leach columns evaluate the flow of leach solution throughout the ore bed. Systematic studies have been completed on a wide range of binders using these novel testing procedures. It was found that for a low grade chalcocite ore, which was rich in silica, from a southwest US mine, polyacrylamides reduced the fines migration the best in the novel soak test. The non-ionic binder, in particular, was found to reduce fines migration as much as 93 per cent. Several of the binders tested were shown to increase the hydraulic conductivities of the agglomerated ore up to 2.5 mm/sec, compared to a hydraulic conductivity of only 0.25 mm/sec when no binder was used. These binders also prevented 'slumping' of the ore, which indicates a decrease in breakdown of the agglomerates. The use of a binder also showed no interference with leaching reactions in long-term leaching experiments.

Sep 13, 2010

By G Baiden

The removal of rock blockages in mining operations has long been a risky undertaking, especially in high overhead conditions. Moreover, the assessment of where to put charges and the placement of them has been difficult due to the lack of visibility and safe access to the area. Traditionally, wedging long poles with explosives on them to keep the operator at a relatively safe distance has been the tried and true method of attempting to remove the blockages. Unfortunately, this is not a perfect system as it usually takes several attempts to remove the blockage. Each successive attempt results in even more dangerous conditions for workers and/or damage to the mine due to the successively larger amounts of explosives used until the hang-up finally comes down.Over the years, different ideas have been proposed to improve this process and reduce the inherent safety risks. Some of the technologies that have been trialled include projectiles fired at the hang-up; large, cumbersome arms; and massive amounts of explosives, each of which come with their own inherent safety risks that result in dangerous situations for miners and the mine.After gaining a thorough understanding of the process, Penguin Automated Systems Inc has developed a robotic system that is capable of working in a rock blockage safely. The idea combines the latest in telerobotics technology with 3D scanning and underground geospatial positioning. The hang-up removal is performed by scanning the inside of the hang-up to rapidly develop a geospatially placed 3D model for the operator to use. The 3D model is detailed enough that the operator can attempt to pick the ‘keystone’. A blasting engineer or the operator can then determine the exact position where the explosive charge should be placed in the 3D model and thus at the actual hang-up. The operator, controlling the robotic arm, uses the 3D virtual reality model of the robot system and the actual drawpoint information model to display the location information, the arm can then reach into the hang-up to position the charge using the kinematic model of the robot system. The 3D model is used to provide views inside the hang-up so that the operator can move the arm safely and precisely. This process allows the operator to place the charge (using the 3D representation of the drawpoint) from a long distance away. As the process continues, the end of the arm drills the rock and precisely loads the explosives. The robot then returns the blasting cable to the command station, which is located in a truck at a safe distance from the blockage.This paper will review the development of the system and present the results to date.CITATION:Baiden, G, 2016. Robotic hang-up assessment and removal of rock blockages in mining operations using virtual reality for safety, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 745–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Sedimentary pyrites from Tasmania have Se contents that are high for it province showing no overall Se enrichment. Sulphides from Devonian granitic rocks, and related cassiterite-sulphide deposits, Sn-Wand PbZn-Ag fissure veins have similar and relatively low Se contents, and pyrites from Devonian gold-quartz veins have very low Se contents. The high concentrations of Se at Mount Lyell are consistent with enrichment in pyritic Cu deposits in volcanic rocks elsewhere, and the dispersion of Se is consistent with a surface volcanic origin for several of the orebodies. In contrast, sulphides from Cambrian volcanic rocks and associated granitic rocks, and from the Rosebery and Hercules pyritic PbZn deposits, also believed to be of volcanic origin, are impoverished in Se.In the Mount Bischoff cassiterite-sulphide deposits there is no relationship between Se content of sulphides and temperature of formation as indicated by fluid inclusion studies, and sulphides from Devonian ores with different temperatures of formation have similar Se contents.The Se content of Tasmanian sulphides appears to be an unsatisfactory discriminant of their genesis and temperature of formation but in volcanic terrains may be a useful pathfinder for Cu concentrations.

Jan 1, 1969

By I M. Platten, C J. S Sangster, Y Xie

The Cononish gold-silver deposit is a steep, relatively narrow quartz-vein system, with a current total mineral resource of 154 000 oz Au and 589 000 oz Ag. The northeast-southwest trending system was emplaced into late Proterozoic metasediments, and postdates metamorphism and associated Caledonian Orogenic foliations. Assay and mineralogical data show that gold and silver is spatially associated with sulfides in quartz. The main sulfide is pyrite, but galena, chalcopyrite and sphalerite occur in small amounts. Gold occurs as electrum, with minor native gold, and silver occurs additionally as tellurides and native metal. The gold/electrum is fine-grained, generally less than 100 microns in size. The main ore shoots plunge 45¦ south-west, have a 40 m to 80 m intersection with the existing underground development and extend between 40 m and 260 m down plunge. Small-scale sulfide-bearing domains within the vein carry the highest gold grades. They collectively define the ore shoots, where one or two, and rarely three, of the domains are present at an individual site in the vein. Discontinuity of individual domains, variation in domain thickness and internal heterogeneity results in short scale variation in grade across the structure. Geological mapping along a 1.2 km exploration adit has provided critical æconditioningÆ data to support resource evaluation based on development and relatively wide spaced drilling. In addition, it has provided an indication of potential challenges that could be encountered during production.

Jan 1, 2009

A review is made of the limited published experience of the effects of cemented fill in flotation.A general approach is adopted in listing and discussing possible sources of, and reasons for, ore contamination by cemented fill, together with basic, fundamental approaches to minimizing this contamination. These approaches involve basic mining design, effect of fill placement density, optimization of curing time and of cement content, variation of fill particle grading, use of flocculants and of pozzolans, fill placement and dewatering, and or blasting and handling practice.

Jan 1, 1974

By D Lautier, A A. Ndiaye, A Galli

Traditionally gold producers had built up hedge books to protect themselves against adverse changes in the commodity price, but diversified mining groups were staunchly opposed to hedging in any shape or form. The situation has evolved over the past few years. Gold miners have been reducing the size of their hedge books in line with the rising gold price. Commentators have talked about ædouble-digit dehedgingÆ and have suggested that this is the final countdown for gold hedge books. It sounded as if the era of hedging by mining companies was drawing to a close. But as appearances can sometimes be misleading, we decided to find out what mining companies were actually doing. Companies listed on stock exchanges are now obliged to give details of their derivatives holdings in their annual reports. Two or three years ago there was no such obligation. Our reality check was based on the latest annual report issued by three multinational mining groups; two with diametrically opposed views on hedging (Rio Tinto and Barrick) and the third (BHP Billiton) with an intermediate position. This snapshot of their derivative positions at a point in time revealed that Barrick and BHP Billiton have substantial derivatives positions (worth billions of dollars) to protect against adverse changes in foreign exchange rates and interest rates. Moreover Barrick has recently started hedging against increases in fuel prices. Despite its opposition to hedging, Rio Tinto has derivative positions worth several hundred million dollars, but these are primarily a legacy from various mergers and acquisitions over recent years or were entered into as a condition of project financing. Lastly we were surprised to discover that Barrick was holding asset-backed commercial paper (ABCP). So the idea that mining companies donÆt hedge their risks is just another urban myth.

Jan 1, 2009

Coking coals are very much in demand on a world wide basis, particularly the higher rank coking coals, which form an important part of many coking blends and which represent the smallest portion of the world'scoking coal reserves. Conventional coke oven plants, using these coals, will predominate at least until the next century.Blending schemes for conventional coking require definition of the basic properties of coals so that the factors influencing the carbonization behaviour may be assessed. Several concepts, which are relatively simple, ate available to help promote a better understanding of the bask factors controlling -coke strength and are also useful in suggesting possible lines to follow in the blending of coals for coking.The interpretation of carbonization behaviour and coke structure in terms of petrographically defined coal rank and type provide a basis for planning and exploitation of coal Teserves. The optimum parameters for coking are suggested as follows.1. Type- Vitrinite content (% m.m.f. by volume) 55 ± 5%2. Rank- Mean maximum reflectance of vitrinite 1.30 ± O.10% Carbon content of vitrinite (% d.m.m.f.) 87·5 ± 1·0%The value of a coal should be assessed in relation to all its possible uses in blends. This is a more realistic and productive approach, as compared with considering coals only in relation to the results of blending with"good" coking coals. Blending schemes have been outlined to assist in the assessment of the blend potential of coals of all ranks and types.Reserves of higher rank coking coals in N.S.W. are very limited and should be conserved by blending with the low rank coking coals, of which there are large reserves.Examination of blending theories in relation to N.S.W. coals suggest that blends in the broad categories of minimal downgrading of the higher rank N.S.W. cok...

Jan 1, 1972

Detailed characteristics of gold from Pliocene auriferous quartz gravels from Waimumu (Southland) have been studied using a combination of optical microscopy, energy dispersive microprobe analysis and scanning electron microscopy techniques. The gold at Waimumu is classified as either: 1. detrital gold, or 2. irregular gold. A number of different morphologies a recognisable within each 'gold type'. Evidence is given for an predominently authigenic origin for some of the gold at Waimumu.

Jan 1, 1987

The Nena high sulphidation-type copper-gold deposit is composed of andesitic pyroclastic units with minor interstratified lava flows. Epiclastic sandstone and conglomerate, and siliciclastic rocks consisting of mudstone, shale, lithic and bioclastic sandstone and conglomerate are locally present. Pre-mineral diorite intruded and domed the volcano-siliciclastic sequence. Economic copper-gold is hosted by vuggy quartz altered lapilli tuff and tuff breccia. The early hydrothermal alteration stage involved deposition of epithermal banded quartz and chalcedonic silica in localised environments. This alteration stage was locally superimposed by a hydrothermal breccia event. Following the breccia event, magmatically-derived volatiles were channelled through a NW striking dilational fault zone and generated the high sulphidation alteration. The high sulphidation alteration is zoned from a vuggy quartz core with local massive replacement silica through a broad pyritic quartz-alunite halo and finally to a thin illite-smectite zone. This is surrounded by regional chlorite-epidote-smectite alteration. A gangue mineral phase consisting of quartz, alunite and baryte overprinted the zoned high sulphidation alteration and preceded the main copper-gold-arsenic mineralisation. Early sulphide deposition is characterised by marcasite, arsenical pyrite and melnicovenite. Main-stage copper-gold mineralisation involved sequential deposition of hypogene bladed covellite+chalcocite, enargite-luzonite and luzonite+stibioluzonite respectively. The copper sulphides are zoned from bladed covellite-chalcocite in the north (cross-sections 5000 - 5600 N) through enargite-luzonite (cross-sections 4700 - 5000 N) and to luzonite????stibioluzonite in the south (cross-sections 4400 - 4700 N). A late phase of minor acicular covellite and enargite+luzonite overprinted the zoned copper sulphides and associated gold mineralisation. Gold mineralisation commenced at the transition from enargite to luzonite, and continued through the deposition of luzonite-stibioluzonite in both stages. Most gold was deposited during the main-stage mineralisation. Yellow native sulphur was deposited in the remaining vugs and defines the waning stage of the hydrothermal system. Post-mineral dioritic intrusives and feldspar porphyries intruded the volcano-siliciclastic sequence. Finally, supergene chemical processes with associated erosion and uplift generated a 40 - 50 m thick oxide-hosted gold cap. The oxide gold cap is underlain by a 35 - 45 m thick blanket of supergene chalcocite+covellite mineralisation which overlies and occurs throughout the main hypogene copper-gold zone. Supergene gold is related to the distribution of primary gold-bearing sulphides. Therefore, remobilisation and redeposition of gold are considered to be insignificant and very localised.

Jan 1, 1999

By M Stewart

Alluvial gold deposits in the area studied are preserved on the valley floor and elevated terraces due to a sequence of glacial/interglacial events during Pleistocene and Recent times. Continued regional uplift has overprinted these events. Prospecting by drilling and bulk sampling has demonstrated a complex alluvial gold resource which is now being mined.

Jan 1, 1989

By Probert D. H, Wright E. A, Taylor B. L

A general description of the geology of the Southern Coalfield is given. The relationship between the Illawarra Coal Measures, the overlying Triassic and the underlying Upper Marine Series, of Permian age as are the Coal Measures, is briefly explained and thestratigraphy of each is described. The eight coal seams are then treated in slightly more detail as to their thickness, quality, areas of distribution and best occurrences.In the last few years each of the authors has been concerned with one phase or other of the stTucture of the field in detail or in mining operations with the result that it is now possible to name a number of monoclines, anticlines, domes and synclines defined in detail. A minor quantitative study has been made of faults and dykes with regard to form, direction intensity and inter-relationship. It seems probable that with the further collection of data a more detailed study in these matters will be of considerable value to the economy of mining in the Southern Coalfield.

Jan 1, 1958

By T P. Fischer, S N. Williams, N C. Sturchio

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these 'primary' components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995

Upgrading of Superfine Low-Grade Haematite Ores by Reverse Floatation Direct Reduction Low Intensity Magnetic Separation Process

Sep 13, 2010

The information age has definitely arrived and in fact has only begun to affect our business processes. Traditionally mining companies have been innovators and leaders with technology, but applying information technology systems to machines directly working on the mining extraction process poses challenges to those introducing the technology. Caterpillar is now presenting machine guidance and information systems for dozers, graders, blast hole drills, shovels, excavators, wheel loaders and trucks. These systems simply increase the flow of real information in real time and deliver it to the end users who can make informed decisions that effect real productivity gains and at the same time eliminate the role of the middle manager who used to monitor and control these activities. Technology also offers cultural changes that appear intangible, but offer significant gains to those that implement technology. Critics state that these intangible benefits are still available to traditional processes, however these intangible elements are never identified nor managed without the introduction of technology enhanced processes. The benefits of these technologies are real and dramatic, existing users offer impressive testimonials, but still the technology can be disproportionate in the time it takes to introduce to an operation. Caterpillar finds that senior to executive management needs to be a part of the technology introduction, to coordinate all departments and set technology strategies.  

Jan 1, 2000

By F F. Pitard, K J. Ehrig

The Olympic Dam iron-oxide copper-gold (IOCG) uranium-silver deposit is second in size only to Norilsk, the gigantic metalliferous deposit. Olympic Dam is the largest publicly declared uranium, fifth largest copper and third largest gold resource. The deposit is typified by texturally destructive brecciation and intense iron metasomatism of the Roxby Downs Granite, bedded clastic facies rocks and mafic-ultramafic dykes. The deposit contains over 100 minerals. Copper mineralisation consists of chalcopyrite, bornite and chalcocite. Uraninite, coffinite and brannerite are the dominant uranium-bearing minerals. Gold mineralisation consists of electrum, tellurides and Au-Cu alloys. Hessite is the major silver-bearing mineral. The economic minerals are disseminated throughout the breccia matrix where the average grain sizes of the Cu-sulfide, uranium, gold and silver minerals are ~50, 20, <5, <5 microns, respectively.A significant number of sampling theory-based test programs have been completed since the mid-1990s to establish sampling nomographs, select appropriate sampling (ie split versus chip and interval lengths) and sample preparation protocols, quantify the errors associated with each subsampling stage, determine the practical uncertainty limits of Olympic Dam matrix-matched standards, and identify improvement opportunities related to the ongoing assaying quality assurance / quality control (QA/QC) program. Invaluable knowledge and unexpected insights gained from sampling studies at Olympic Dam have helped to improve our understanding of the distribution of economic and deleterious elements within the Olympic Dam deposit.CITATION:Ehrig, K J and Pitard, F F, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Eighth World Conference on Sampling and Blending , pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By A Raza, D P. Kohn, D A. Foster, A J. W Gleadow

A large and increasing data base of apatite fission track results from sedimentary and granitic rocks exposed within the south-eastern highlands and along the continental margin ofAustralia provides constraints for the tectonic development of the south-eastern passive margin. The fission track results suggest that many regions of the south-eastern margin of Australia experienced distinct episodes of relatively rapid cooling during the middle Cretaceous to early Tertiary that can be attributed to the effects of rifting. One cooling episode is middle Cretaceous in age and related to denudation of the south eastern highlands from Tasmania to northern New South Wales between ~90 - 100 Ma. Rocks exposed along the present coast line record a later episode of rapid cooling, which is diachronous and decreases in age northward from ~80 to 90 Ma in northern Tasmania to southern New South Wales, ~60 - 80 Ma in central and northern New South Wales, and to ~50 - 60 Ma in southern Queensland. The results are consistent with models suggesting that underplating occurred inward of the rift along the eastern margin of Australia as a result of the onset of continental extension in the Tasman Sea at ~96 Ma. This resulted in a significant change in base level and km-scale denudation of much of the southeastern highlands. Subsequently, as breakup commenced during the Late Cretaceous at ~80 Ma and continued into the Paleocene at ~60 Ma, the second stage of cooling was imprinted on the rocks along the margin. This cooling is probably due to the relaxation of elevated geothermal gradients associated with rifting as well as some denudation. Because rifting was oblique to the present-day coast, different regions record different ages of cooling associated with the rift. The southern regions of New South Wales and Victoria yield ages associated with earlier rifting while regions of northern New South Wales and southern Queensland give ages associated with later rifting.

Jan 1, 1995

By W L. Jennings

This paper summarises work undertaken to date as part of an investigation into the mineral resources of the proposedNorth West South Island National Park. The area covered by the proposed national park is underlain by many rock types that have undergone a long and complex history of evolution which has endowed it with some of the best potential for a wide range of different minerals in New Zealand. Many of these minerals occur only in this area or in Fiordland National Park.   The first gold-rush in the area occurred in 1856 and followed the discovery of payable gold at Lightbands Gully, south of Collingwood. The miners first focused on the alluvial deposits but soon shifted attention to lode potential. The total historical gold production for the area may be over 400 000 oz (NZ$250 - NZ$295.6 M at 1993 prices).   In addition to gold, a wide range of other minerals have been reported from the area including molybdenum, copper, nickel, zinc, silver, bismuth, stibnite, lead and antimony. The Onekaka iron-ore deposits have produced small tonnages of ochre and iron-ore at various times. Tungsten, platinoids and other metals have been. given only minor attention. The diverse geology of the Northwest Nelson has resulted in the occurrence of many industrial minerals which have been exploited in generally small-scale operations. Aggregate, chrysotile asbestos, clay, dolomite, marble, limestone, dimension stone, rip-rap, talc-magnesite and wollastonite have all been produced.

Jan 1, 1993

It cannot be said that accurate and reliable ore reserve estimation is the fundamental of any mining operation success. Estimation techniques which are used to estimate the grade distribution of an orebody together with the assessment of uncertainty and risk have a vital influence on the success of any optimisation algorithm. Traditional estimation techniques such as kriging or inverse distance weighting are frequently used for assigning grade values to blocks. Various attempts have been made in order to compare geostatistical estimated methods for ore reserve estimation. This paper aims to evaluate the sensitivity of different estimation methods over changing the block dimension. For this reason, several block models with different dimensions were derived in Chador Malu iron ore mine which is located in 180 km northeast of Yazd in the centre of Iran. Each block model was estimated by different estimation methods such as nearest neighbours (NN), inverse distance (ID) and ordinary kriging (OK). The results of each estimation methods were compared against a control block file created by using the assay results of all blastholes drilled in the ore over four benches of the pit. The results signify that by estimating the large block size, no significant improvement occurred due to the employment of different estimation techniques. Furthermore, the grades estimated based on ID method is more reliable, but OK methods estimated more accurate tonnage.

Dec 6, 2010

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986

By K C. Williams, A W. Roberts, J D. Prigge

For stockpile design, the flowability and structural interfaces are critically dependant on the stress conditions throughout the pile. Historically, the predictive methodologies for stress determination have been too conservative, which adds inefficiency to the stockpile reclaim interface selections, especially for live reclaim stockpile systems. In addition, accurate pressure profiling throughout stockpile is essential to correctly design the stockpile support structures, which are buried within the stockpile. Such buried structures include trestle legs or columns to support load-out conveyors or the roof of bulk storage sheds. Improved methodologies with respect to the development of the hoop stress condition which exists in material ædrawn-downÆ within the stockpile has been developed. This hoop stress approach has significantly improved the live capacity prediction to over 90 per cent accuracy and improved rathole structure prediction within live reclaim stockpiles. Additionally the methodologies in estimating the vertical and circumferential stress variation acting on buried stockpile structures have been significantly progressed, with experimental testing shown good agreement with the theory.CITATION:Williams, K C, Roberts, A W and Prigge, J D, 2013. Recent developments in stress analysis and live reclaim prediction within iron ore stockpiles, in Proceedings Iron Ore 2013 , pp 501-510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013