Search Documents

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

MIM Holdings Limited (MIM) committed to a long-term future in copper in the Carpentaria Mineral Province in 1996 with the development of the Enterprise and Ernest Henry mines, and an upgrade of MIMsÆ copper smelter in Mount Isa, and copper refinery in Townsville. The upgrade of the copper smelter will enable the smelter to produce 250 000 tpa of copper with a single primary smelting unit, the copper Isasmelt furnace installed in 1992. The copper Isasmelt furnace currently smelts concentrate containing 145 000 tpa copper. To reduce the risk associated with the copper smelter upgrade, and shorten the ramp up time of the upgraded smelter, two high-rate trials were undertaken in 1997 to demonstrate that the copper Isasmelt furnace could, with an additional 525 tpd of tonnage oxygen, treat concentrates containing 250 000 tpa copper. During the trials the concentrate feed rate to the Isasmelt furnace was increased from its average rate of 100 tph of concentrate to 150 tph of concentrate. The increase in the capacity of the furnace was achieved by: supplementing the installed tonnage oxygen capacity of 595 tpd with an additional 300 tpd supply; reducing variability in the furnace feed rate from ¦25 per cent to less than ¦5 per cent; and reducing tramp air. The Isasmelt furnace smelted concentrate at a rate of 140 to 150 tph for four hours 25 minutes during Trial 1, and at a rate of 150 tph of concentrate for five hours and 30 minutes during Trial 2. The oxygen utilisation was 100 per cent during the trials with the process remaining under control. As a result of the development work for the trials the average treatment rate of the furnace under normal conditions increased by ten per cent.

Jan 1, 1998

By R Wei, Y Peng

With the depletion of high-quality ores, the efficiency of extracting difficult gold ores through flotation and leaching becomes very important in the mining industry. Iron contaminants, sulfide and carbonaceous coatings on the surface of gold and gold bearing minerals significantly hinder the recovery of gold during gold processing. As the surface of gold minerals is easily contaminated, coatings of iron oxides and iron hydroxides originated from the grinding process and oxidation of iron sulfides will cause a retarding effect on both gold flotation and leaching.To mitigate the processing issues caused by undesirable surface coatings on gold minerals, a new technology in treating surface coatings of iron contaminants has been developed. The pulp potential and pH of the slurry are altered to allow dissolution of surface coatings which are further excluded by the use of complexing reagents. The current work shows that iron contaminants can be removed from the surfaces of gold through Eh-pH adjustment and chelation which result in significantly improved gold flotation response. The addition of complexants aids the formation of iron chelates to prevent the iron species in the solution from forming iron oxide and iron hydroxide in the flotation conditions.CITATION:Wei, R and Peng, Y, 2014. Mitigating the effect of surface coatings on gold processing, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 187–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R G. Reddy, Z Zhang

Viscosities of CaO-aluminosilicate ternary melts were estimated using a structure-based model. The model considers depolymerisation effects and related breakdown of the silicate network structure on the addition of metal oxides to the melts. The predicted values are in good agreement with the experimental values over the whole temperature and composition range.

Aug 21, 2024

By X Yu, Y Shen

The iron ore products should be assessed in terms of in-furnace behaviour and overall furnace performance, their operation should also be optimised under industry-scale blast furnace (BF) conditions, in order to be sustainable and competitive, especially in the context of decarbonisation efforts in ironmaking. While lab and pilot-scale experiments can provide useful kinetics, they are expensive and risky and cannot replicate industry-scale blast furnace conditions for proper assessment and optimisation. In this paper, we review our recent progress at Shen Lab of UNSW in using state-of-the-art Computational Fluid Dynamics (CFD) models to assess iron ore products and examine the effects of their operations on BF behaviour in basic terms, including in-furnace phenomena (flow field, temperature field, species distribution fields etc) and overall BF performance (coke rate, reduction efficiency and top gas temperature etc). We have developed state-of-the-edge CFD models for different purposes, ranging from the static-state BF model featuring unique layered burden structures for offline assessment and optimisation knowledge building-up for iron ore products, to the transient-state BF model for online assessment and optimisation of iron ore productions by describing the transient behaviours of iron ore productions under industry-scale conditions. First, we have studied several iron ore products including the iron ore products used in the present BFs and emerging iron ore products like carbon composite briquette and iron-coke. Second, several iron ore operations are studied including optimisation of conventional burden operations like oxygen enrichment, batch weight tuning and new operations like coke central charging and hydrogen injection in BFs. Third, some time-sensitive operations are also investigated including the use of wet burden materials and the drop in blast temperature on BF performance. These CFD models offer cost-effective research tools for understanding the effect of iron ore products on BF performance and serve as a reliable marketing tool for existing and emerging iron ore products under a wide range of BF conditions.

Sep 18, 2023

By H Aoki, A Nakayama, K Morita, S Yamada

The thermal conductivity of mold flux is crucial for optimising the productivity and quality of steels. This study investigates the thermal conductivity of molten oxides, including CaO-BO1.5-AlO1.5 (CBA), CaO-BO1.5-AlO1.5-SiO2 (CBAS), and CaO-MgO-BO1.5-AlO1.5 (CMBA) melts, using a hot wire method. Additionally, their structure is examined using Raman spectrometry and magic angle spinning nuclear magnetic resonance (MAS-NMR) to explore their relationship. Furthermore, first-principles calculations are employed to assess the covalency of each bond in the melts for a more quantitative analysis of their relationship. The study confirms that an increase in the CaO concentration of the CaO-BO1.5-AlO1.5 melts reduces the amount of bridging oxygen and consequently decreases thermal conductivity. The covalency of the B[4]-O bond is highest, especially when the second-nearestneighbour Al atoms transition from Al[6] to Al[4], forming the AlB3O7 structure with B[4]. The relationship between thermal conductivity and the structure of CaO-BO1.5-AlO1.5-SiO2 melts can be quantitatively assessed using the degree of polymerisation of the network structure and the variation of covalency as indicators. Furthermore, replacing CaO with MgO in the CaO-MgO-BO1.5-AlO1.5 melts reveals a mixed alkaline earth effect on thermal conductivity.

Aug 21, 2024

By E A. Agorhom, M Beyuo, C Owusu, I Quaicoe

Understanding the mineralogy and liberation of gold particles in an ore is key to the development and optimisation of gold processing operations, being cyanidation or gravity separation. This can be achieved through basic historic geological information, gold deportment studies, chemical speciation and metallurgical test works. The present study assessed the nature of the occurrence of gold particles (mineralogical composition, liberation, associations and surface chemistry) and its effect on the process route (cyanidation and gravity separation) of a typical paleo placer gold ore deposit within the Tarkwaian Rock system. The investigative approach used involved chemical assay, quantitative X-ray diffraction (QXRD) and quantitative evaluation of minerals using scanning electron microscopy (QEMSCAN). The ore samples (A, B, C, D, E, F) used were obtained from six active pits of a gold mine working on this orebody. The results of the mineralogical analysis revealed that the ore is highly oxidised and comprised quartz (>80 per cent) and Muscovite mica (>6 per cent) as the major mineral phases in all the samples. Trace amounts of hematite, kaolinite and todorokite were also identified in all the samples. The chemical analysis showed presence of gold (Au) in all the samples with samples B (3.62 g/t) and C (3.96 g/t) containing the highest concentrations. Trace amounts of copper (Cu), iron (Fe), sulfur (S), aluminium (Al), arsenic (As) were also detected in all the ores. The QEMSCAN mineralogical liberation and gold association results revealed that the gold grains were relatively coarser in all samples (P80 > 80 µm Au in size) except F (P80 < 32 µm Au in size). Gold grains were highly liberated especially in sample B with the majority of the locked gold grains forming complex associations. All the samples responded well to cyanidation and gravity separation except samples C and F, respectively.

Aug 24, 2022

The history of the discovery and development of the Kambalda nickel orebody. is reviewed and the decision to process the Kambalda concentrates by the Sherritt-Gordon process at Kwinana is discussed. The Kwinana Nickel Refinery is described and the problems encountered in the first year of operation are Outlined.

Jan 1, 1971

By T Perera, B Fan, S Thang, T Hsia

The mining industry is currently focusing to develop and adopt sustainable collector chemistry that can efficiently recover valuable minerals from their natural state. However, a limited number of research can be seen on the design and synthesis of polymeric flotation collectors. The focal objective of this research is to synthesise a more effective polymeric collector with advanced architecture to utilise in the mineral processing industry. Reversible Addition-Fragmentation Chain Transfer (RAFT) co-polymers with cardanol derivatives have the potential to selectively trap valuable metals in the flotation process in a more efficient way. Cardanol exhibits amenability to chemical modification for making tailor-made monomers that can further produce polymers with high value. The synthesis of a series of fit for purpose copolymers in this study was accomplished by RAFT polymerisation. The ability to design complex architecture is a significant advantage in engineering polymeric collectors by RAFT polymerisation. Initially, commercially available cardanol was converted to a cardanol based monomer and copolymerised with commercially available monomers to synthesise a series of novel cardanol based copolymers with predetermined molecular weights. The side groups of the copolymer were chemically modified to incorporate functionality that can be selectively adsorbed on the chalcopyrite surface.

Aug 24, 2022

By Shuguang L, Jing S

Computer controlled truck dispatching systems is a newly-developed technical system in surface mines with shovel-truck technology. The real time dispatching criteria, as the core of optimal truck dispatching software, are analysed and a new criterion, complex dispatching criterion, is put forward. Dispatching criteria previously proposed include: 1. `Earliest Loading&apos; (EL) - to assign a truck to the shovel at which the truck can be loaded earliest. 2. `Max Truck&apos; (MT) - to assign a truck to the shovel at which the truck will have the shortest waiting time. 3. `Max Shovel&apos; (MS) - to assign a truck to the shovel which has been waiting for the longest time. 4. `Minimum Saturation Degree&apos; (MSD) - to assign a truck to the shovel at the branch where the truck flow saturation degree is minimum. 5. `Minimum Saturation Degree with Truck Cycle time consideration&apos; (MSDTC) - as the MSD principle, with the truck travel cycle also considered. 6. `Fixed Dispatching&apos; (FIX) - to assign trucks to fixed shovels. A system simulation model has been set up for truck dispatching system analysis. A few surface coal mines have been selected for case studies. Equipment waiting times and shift production of the system are obtained as the main outputs of the model. Simulation results show that each dispatching criterion has its own applicable range, no one can absolutely dominate the others. For example, when under-trucked, EL and MT criterion can obtain higher production than the MS criterion; when over-trucked, it is vice versa; while for MSD criteria, better results can be obtained no matter how the truck numbers fluctuate. From the view point of shovel output balance, large fluctuations occur for EL and MT criteria, while a good balance can be obtained for other criteria. In the light of dynamic change of mining system conditions, a single dispatching criterion is not necessarily reasonable. A complex dispatching criterion has been put forward to seek the complex optimum effect. Taking the advantage of each dispatching criteria, the dispatching result of a complex dispatching criterion dominates over individual dispatching criterion and a comprehensive optimum effect can be reached.

Jan 1, 1995

By Wang S

Fragmentation is the basic concern in rock blasting and serves as the main measure of blasting effectiveness. A good estimation of fragment size distribution before blasting is very useful and helpful for selecting the proper equipment for loading, transporting, and crushing rocks. A fragmentation model is presented that is based on a hole by hole analysis and correlates the rock properties, burden, spacing, and explosive column with the blasted volume and fragmentation obtained. The drill bench is divided into three separate areas corresponding to different breakage mechanisms. They are: 1) a main breakage or casting area, 2) a secondary breaking area, and 3) an overbreak area. The boundary of the main breakage area is found from the magnitudes of strains in the stress waves and the tensile strength of the rock. The secondary breaking area is determined by stress wave reflections at discontinuities and interactions between colliding stress waves from adjacent boreholes. The overbreak area is that beyond the main breakage area "where the reflected tensile waves no longer break the rock. This analysis is applied on a hole by hole basis to locate the breaking points. Then connecting the breaking points on each side of a borehole forms the triangle of the main breakage area. This is repeated for the next hole and the remaining area is the secondary breakage area. After the angle and area for each hole are found the Kuz-Ram model is used to predict the fragmentation size distribution for each hole. Then summing up the size distribution for each hole gives the total fragmentation distribution. This analysis has been successfully applied to field tests performed in a limestone bench where the entire spoil pile was screened to determine the fragment size distribution. Knowing the explosive and rock properties the breaking area was found for each hole, the strain and stress values, the breaking point, and angle of breakage (104 degrees). The fragmentation size distribution was then calculated and compared to the field data with excellent agreement.

Jan 1, 1990

By M D. Urbani

HiTec Energy Ltd has been conducting research since 1996 into novel process routes for the treatment of low-grade and waste manganese sources for the production of high value and high quality electrolytic manganese dioxide (EMD) for the alkaline battery market. HiTecÆs approach is to treat previously unsaleable manganese deposits and mine site tailings using a novel sulfur dioxide leach route, followed by purification and electrowinning to generate the sought-after EMD product by an environmentally superior processing route to those presently practiced throughout the world today.HiTec Energy Ltd expects to be in commercial production with its Stage 1 facility in Kalgoorlie in the last quarter of 2004 for the production of 12 500 tpa EMD. With this production facility being adjacent to a laterite nickel producer with available waste manganese units, the opportunity arose for HiTec to combine its existing technologies with processes (that will be discussed in this paper) to turn two waste by-products into products that are used for high-tech purposes.HiTec Energy Ltd and the Parker Centre have had a collaborative research relationship for a number of years in areas involving EMD and battery related technologies. Meanwhile the solvent extraction (SX) group of the Parker Centre (CSIRO Minerals) has developed SX processes to separate manganese from nickel and cobalt. A project was initiated by HiTec Energy to recover manganese from waste laterite leach solutions using SX technology. Batch tests were conducted to select a suitable organic system for the extraction of manganese in terms of selectivity and extraction and stripping kinetics.A total of eight organic systems were tested by determining pH isotherms of metals using a laterite nickel process waste stream. Two organic systems, the Versatic 10 and Versatic 10/synergist systems, were chosen for further test work with Shellsol D70 chosen as the diluent for both systems.The Versatic 10/synergist system would be advantageous over the pure Versatic 10 system because fewer SX stages are required, resulting in a smaller organic inventory and lower capital costs. The risk of gypsum formation is also significantly lower with the synergistic system.

Jan 1, 2004

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

By R G. Reddy

The complexity in treating environmentally harmful impurities such as As, Sb, Bi from the base metal matte or metal in the smelting stage are responsible for the high cost of the refining process. The impurity capacities (such as arsenic, antimony and bismuth) of slags were calculated a priori using Reddy-Blander (RB) model. The capacity predictions were for a wide range of matte and slag compositions in copper smelting conditions. The calculated impurities capacities and impurity distribution ratios results are in good agreement with the available experimental and industrial slags data. The a priori knowledge of impurities is useful for reduction of energy consumption and enhanced environmental control in the current and future non-ferrous metal processes.

Aug 21, 2024

By J A. Rumball

Measuring cyanide in the leach liquors associated with high copper and/or sulfide ores is a non-trivial exercise. It is well known that copper complexes with cyanide and reduces the amount of cyanide available for gold leaching. What is not so well known is that the rhodanine end point overestimates the amount of cyanide available for leaching in the presence of copper. Sulfide ions also interfere with a rhodanine end point titration, although this is less of a problem as the black silver sulfide precipitate formed clearly indicates to the operator that something is wrong. Thiosulfate, which forms readily from the alkaline oxidation of sulfides, causes an overestimation of the cyanide available for leaching due to the formation of Ag(S2O3)-. The net result of these observations is that rhodanine is rarely of value as an end point indicator in complex solutions. It generally overestimates the amount of cyanide available, providing plant metallurgists with a false sense of security. Potentiometric titrations are generally much more capable of accurately measuring cyanide in complex solutions. The interfering effect of copper can be resolved and it is even possible to estimate the copper concentration using the inflexions associated with the titration of CN- + Cu(CN)43- versus Cu(CN)32-. Using the potentiometric method sulfide ions can be determined before the cyanide measurement is made due to the formation of AgS2, although the electrode will foul with repeated measurements. Thiosulfate can also be distinguished from cyanide with a potentiometric titration. Rhodanine and potentiometric titrations are both affected by the pH of the liquor. At pH 9.2 half the cyanide will be present as CN- and half as HCN(aq) with only the CN- being titratable. This does not hold in the presence of a buffer active around pH 9. In the presence of sufficient buffer, both the CN- and HCN(aq) are titrated. Ca(OH)+ may buffer the pH when large amounts of lime have been added.

Jan 1, 2007

By M Gwynne

McArthur River Mine is located approximately 50 km south-east of the NT township of Borroloola and approximately 120 km from the Gulf of Carpentaria. The mine hosts a series of layered shallow dipping tabular orebodies, with current reserves of approximately 22 Mt, grading 13.6 per cent zinc, 6.3 per cent lead and 65 g/t silver. Owing to economic considerations, the lower most orebody (No 2 orebody) has been selected for initial mine production. Following the completion of the No 2 orebody, mining will transfer to the lower grade and metallurgically more complex No 4 orebody. The mine employs a total of 235 people throughout the underground and surface areas. The majority of the workforce work a fly-in/fly-out, seven-day- on/seven- day- off roster with 12-hour shifts. Presently, a further 18 contractors are involved in trial mining areas. An apparent dip room and pillar technique has been selected as the primary mining method. Officially opened in September 1995, the current production rate of 1.2 Mt per annum will eventually escalate to 1.5 Mt per annum. Though most production is achieved through the use of conventional loaders, trucks and jumbos, the recent development of methods utilising scrapers, hand held machines and modified jumbos has produced encouraging results in steeper dipping areas of the mine. Initial production has been hindered by several factors including extensive and largely unpredictable faulting, worse than expected ground conditions and difficulties with some mining equipment. Compounded by the relatively thin 3 m ore seam, initial mining resulted in high dilution and poor production. This paper describes the development of unique planning and production systems that were evolved in order to overcome these problems and achieve the targeted production rates and head grade.

Jan 1, 1998

The efficient and profit-maximising daily and long-term management of the Vera Nancy resource depends on decisions based upon assay data. This paper examines the range of sample sources, the methods of sample collection, assay techniques and Quality Assurance used by the mine. The orebody has a relatively low nugget effect for a gold mine (around 25 per cent) and this greatly assists in reducing sampling error and producing reliable assay data for production decision-making. Reconciliation between mine and back-calculated mill grades generally sees the mine under-calling mill grades by around four per cent.

Jan 1, 2000

By R Badreddine, J Rose, L De Windt, P Chaurand, L Raimbault

Municipal solid waste of incineration (MSWI) bottom ashes are recycled as aggregates in civil engineering. These heterogeneous materials are composed of crystalline and glassy solid phases which contain trace metals, presenting a potential risk to the environment. Secondary ion mass spectrometry (SIMS) can provide quantitative chemical information, in particular the localisation of metals at trace level. Unstable glassy phases formed during incineration are present in relatively high proportions. Their analyses suggest a continuum between melilite-bearing glasses and dark glasses enriched in iron with abundant spinel aggregates. These primary glasses are enriched in zinc (~4500 ppm) but depleted in lead (~800 ppm) by comparison with the bulk chemical composition and reference materials. Heterogeneous cementing and encrusting admixtures on coarse grains are studied in a second step. SIMS imaging suggests a superposition of band zones including an intermediate layer enriched in iron oxyhydroxides and a superficial layer with calcium accumulation. A strong spatial association between lead and iron is systematically observed. Extended X-ray absorption fine structure (EXAFS) supports these observations by demonstrating that lead co-precipitation within iron oxyhydroxides, or sorption on their surfaces, may be a main containment process in the cementing and encrusting admixtures, whereas lead speciation is globally more complex in MSWI bottom ash.

Jan 1, 2008

By J Zhang, R Dimitrakopoulos

A two-stage stochastic mixed integer non-linear program is formulated for a mining complex to optimise strategic and tactical plans. The objective is to find the near optimal decisions for a mineral supply chain in the context with uncertainties in both ore supply and the commodity market (price and demand). The endogenous spot price in the commodity market and long-term sales contracts are considered in the formulation of the mining complex’s optimisation model and an ad hoc heuristic is developed to deal with the throughput – and head-grade-dependent recovery rate in processing plants. Numerical results indicate that the proposed heuristic is effective and efficient in numerical tests. Based on the proposed model and heuristic, a long-term contract design strategy is proposed for making decisions on the contract price and strategic investments. A shadow price based method is also proposed to evaluate the existing mining schedule.CITATION:Zhang, J and Dimitrakopoulos, R, 2014. Optimising a mineral supply chain under uncertainty with long-term sales contracts, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 25–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Kwitko G

Exploration for coal has been on-going in South Australia for the past 100 years. During this period substantial resources of low rank coal have been delineated throughout the State. These deposits are of variable quality often with high moisture, sodium, chlorine, sulphur and ash content and although generally regarded as suitable for use in conventional pulverised fuel boilers, many are difficult to utilise. The only operating coal mine in South Australia is at Leigh Creek where coal bearing shale was discovered by chance in 1888 during excavation of a railway dam near the township of Copley. Leigh Creek has had a very diverse mining history from the initial small scale underground mining through to open-cut mining utilising draglines and more recently large shovels and trucks.

Jan 1, 1992