Search Documents

An effective production control system should maximise recovery of economic material from the resource. To do this, internal waste must be accurately delineated and efficiently removed. Achieving this is most difficult in low grade blocks just above and just below the cut off grade, where ore:waste separation follows assay or statistical, rather than geological boundaries. Difficulties arise from sampling errors, configuration of the economic mineralisation, and local variations in geology. Mine bench parameters and mining equipment size apply further constraints to the actual field separation of the ore from the waste. At BCL, management of the resource starts with an effective orebody model for planning, scheduling and ore:waste prediction. Ore production from each mining location is reconciled with concentrator tonnage and grade, and the reconciled grades are compared with the planning orebody model to highlight any Differences.

Jan 1, 1986

The Vera Nancy orebodies, although simple in overall geometry, are in detail generally narrow, multi-veined and fluctuating in width, strike and dip. Tight geological control is required to optimise gold and silver production from this bench stoping operation. The processes used to model the resource and to control ore drive development have evolved since mining commenced in 1997. Grade control is a combination of orebody sampling, geological data collection, understanding orebody geometry and the optimisation of ore driving and stoping activities. Global resource modelling utilises mainly drill hole data which is largely superceded by drive development data as stope development progresses. The orebody has a relatively low nugget effect that assists in grade estimation. Rather than rely on sophisticated grade interpolation methods, resource estimation to-date has focussed on developing the geological understanding of the orebody to ensure the framework for estimation is correct. Drill data alone is not adequate to define deposit geometry for stoping . Drive data is used as the dominant data set for stope geology modelling once development for a stope is complete.

Jan 1, 2000

INDEX OF CONTENTS.1. Historical.2. Manufacture.3. Heat Treatment.4. Fatigue, Failures.5. Consideration of the Establishment o£ a Central Testing or Proving Station.HISTORICAL.Since the introduction of improved high air pressure drilling machines in the early part of the century, efforts have been made to develop the quality of the rock drill bit, in order to take advantage of the greater increase of power output per unit weight of the machines (1). This resulted in the change from solid to hollow steel in the second decade of the present century (2).As the greatest sufferers from the dread disease of silicosis (3), it seemed appropriate that the South African gold mines should be the first to use hollow drill steel. Since then solid drills have become practically obsolete for mining purposes.Water is used with hollow steel drills not only to keep the cutting end cool, but also to assist in preventing the formation of undue dust during drilling. It is of interest to note, however, that water fed through hollow steel or sprayed into the air is only partially effective in removing fine dust particles a few microns in diameter, which particles are said to be the most potent in producing silicosis (3a).So far as the composition of "straight" carbon steel drills is concerned, a commission appointed by the Johannesburg mines carried out a very exhaustive series of tests on drill steels.These drills were manufactured from steel made by all the standard methods, including Swedish, Bessemer, crucible, openhearth, and, to a limited extent, electric furnace steel. It should be remembered that the commissioners' report was issued in 1913, when hollow drill steel had not yet been introduced. Only solid steel drills were then in use.

Jan 1, 1947

The high maintenance of load-haul-dumps (LHDs) and front end loaders in hard rock affects mine planning with reduced availability and productivity. Intensive study of maintenance costs and availability of machines related to machine age and life provide the basis for planning from available operational alternatives.Derived programmes and experiences have led to the beginnings of unmanned operation and automation through reduction of manual diesel units and spreading electrification and use of radio. But electrification has obvious layout limitations. This approach to the present has resulted in better utilisation, costs and safety and the computerised monitoring and control provides continuous awareness of machine and work conditions with the promise of future improvements.

Jan 1, 1991

The Canada Centre for Mineral and Energy Technology (CANMET) /Calgary Coal Research Laboratory and the National Research Council in Ottawa established a joint working research group with industry to develop and test various computer models for application in surface coal mining operations in western Canada.The first part of the paper deals with the problems the group experienced during the past two years especially having model specification and requirements defined and understand site management practices.The second part of the paper deals with site specific development of general mine model for TransAlta Utilities' Highvale Mine in Alberta. Described here are the development of an interactive truck/shovel model for their three pit operation, selection and application of dragline model for tandem operation with the extended bench method, criteria for operational model of the five seams operation with selec-tive mining approach.

Jan 1, 1985

By Mallett C

Coal mines are dynamic systems that change continually in size, shape, and condition. Large quantities of data about production, coal quality, ground stability, ventilation monitoring, equipment performance and location, vehicle and personnel movements and geology, are generated from all parts of the mine.Internet technology and virtual reality technology are now being combined to provide an intuitive, multi-dimensional information system which can simultaneously display any information that can be collected and stored by a computer. Physical information is directly displayed as 3-dimensional objects in the mine model. Numerical and text information is dynamically linked to these objects and accessed by "clicking" on them.

Jan 1, 1998

I am honoured and very pleased to have been given the opportunity this evening to say a few words of thanks not only on behalf of all the guests but especially for the delegates and accompanying persons attending the 13th Congress of the Council of Mining and Metallurgical Institutions. Firstly, I would like to congratulate Sir Hamilton Whyte,KCMG for his most interesting address. In his far ranging talk, when he showed knowledge of widely diverse subjects, I had a brief fear that he was going to be talking about the details of support methods in deep level mines, or how to avoid flotation problems in multi-metal mines. Although he did not go that far, he touched on subjects which have arisen this week - long term planning and secure supply of minerals at acceptable prices. The dire predictions of the Club of Rome have been debunked with a far more elastic supply of minerals having been proved. Combined with the importance of a falling birthrate in some parts of the world, this will lead to many changes in the future, when hopefully governments will take the long term view rather than look at the next budget or the next election. Maybe some of them are not too lazy to do this for all of us. However as a fellow Ukranian, I feel that he might have been called something different if he had been in Australia. Sir Hamilton, thank you for your talk. Once upon a time - and this is not a fairy story - there was a cobbler who had two sons; one very bright who became a professor of mathematics; the other, dim, who became a millionaire shoemaker. Asked for the secret of his success, the millionaire attributed it to a vital piece of economics which his father had imparted, "Be content with small margins on a large turnover." "So", said the millionaire, "I make my shoes for $2 a pair and sell them for $5. I am very happy with the three per cent profit."

Jan 1, 1986

The coal basins that formed near the margin of Permian Australia were comparable in size with the Appalachian coalfields and with the European fields between Wales and Poland. They formed on the foreland side of a growing orogen in a system of linked transform basins formed by transtension on strike-slip faults. They were terminated and compressed when the Gympie volcanic arc was accreted to the orogen. Another huge system of Permian coal basins extending far inland from the Permian coast was also terminated when the Gympie Terrane was Accreted.

Jan 1, 1987

Our ultimate resources come from the Sun and the Earth System. At this time we face a world crisis in energy, water and soil resources. Global pollution problems are increasing in almost all nations. There is an urgent need to use our vast knowledge with a new wisdom and this requires new integrated teams of experts to provide the best alternatives for the needed new development problems. These teams must include economists, engineers and a broad spectrum of scientists. Today it is possible to produce clean energy, stop soil erosion, clean water and reduce and use wastes of many types.

Jan 1, 1995

By OÆBrien D. R

Up until June 1988, Mount Thorley Coal Handling and Preparation Plant disposed of tailings by two methods. Approximately half of the plant tailings was mechanically dewatered by solid bowl centrifuges mixed with plant reject and was subsequently disposed in mine overburden spoils; the remainder was pumped to tailings ponds. Both future mine planning and environmental constraints could not allow for the long term construction of more tailings ponds so, following evaluation of available dewatering technology, belt press filters were selected for the treatment of tailings in excess of the capacity of the existing solid bowl centrifuges. Commission of the four 2.5 metre wide belt press filters soon showed that marked differences in performance were experienced when treating different coal seams. Further analysis showed that the coal tailings from different seams were quite different in terms of clay mineralogy, and these differences could be correlated with varying degrees of filter performance. Poor filter performance was experienced with coal tailings rich in sodium montmorillinite clays. A number of variables were investigated including in-line mechanical mixing of flocculant and feed slurry, cation exchange reagents such as gypsum, and upstream addition of cationic flocculant. In order to achieve satisfactory performance on the worst tailings, a combination of all of the above was required. In this paper, the reasons for selection of belt press filters and the program of investigations and testwork required to arrive at satisfactory belt press filter performance for the treatment of troublesome bentonitic rich tailings are discussed.

Jan 1, 1989

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

By D Pienaar, B McFadzean, C T. O’Connor

Collector and frother molecules in sulfide mineral flotation are thought to have separate roles in the flotation process, where the collector selectively hydrophobizes the mineral surface and the frother adsorbs onto the bubble surface, inhibiting bubble coalescence. Molecular interactions have been observed between these molecules which allow them to co-adsorb at each of the respective interfaces, improving pulp phase recovery. This study investigated the molecular interactions between sodium diethyl dithiophosphate (SDEDTP) and hexanol, and the mechanism by which these interactions improve the recovery of galena. In this study each of the respective interfaces were investigated for the adsorption of SDEDTP. The adsorption of SDEDTP on galena was measured by UV-Vis spectrophotometry and isothermal titration calorimetry. At the air-water interface foam stability and pulp bubble coalescence was used to quantitatively discern if there are interactions between SDEDTP and hexanol. Microflotation and induction time experiments were performed to determine the effect of SDEDTP, hexanol and their mixtures on mineral recovery and bubble-particle attachment. The results of all these tests were collated to determine if SDEDTP-hexanol mixtures synergistically improve sulfide mineral recovery. It was found that SDEDTP reduced bubble coalescence in the pulp demonstrating activity at the airwater interface. Together SDEDTP and hexanol synergistically enhanced foam stability. This indicated that there are attractive molecular interactions between these reagents. Even though DTP did not adsorb onto galena, DTP-frother mixtures synergistically improved the recovery and attachment probability of this mineral. Adsorption studies with aeration showed that DTP in the presence of a frother transfers from the air-water interface to the galena mineral-water interface during bubble-particle collision. It was proposed that the transfer of hexanol through the thin film enhanced the kinetics of film thinning between the bubble and the particle by destabilising the thin film thus improving pulp phase mineral recovery.

Aug 24, 2022

Laboratory high tension roll separation and the commercial machines available for this purpose are discussed. The shortcomings of these machines are indicated and a machine that overcomes some of these undesirable character- istics is described. A procedure for evaluating laboratory high tension roll separation is described. The use of this evaluation procedure in conjunction with the laboratory separation is described with examples taken from the Dunwich and Hexham processing plants of Associated Minerals Consolidated Limited. Evidence that laboratory testwork results may be directly transposed to operating plants is given. A discussion of the effects of variables in high tension roll separation of mineral sand concentrates concludes the paper, and uses in support results obtained in the metallurgical laboratories of Associated Minerals Consolidated Limited, Southport, Queensland.

Jan 1, 1972

By Sakurai F

Akita Zinc Refinery of Mitsubishi Metal Corporation (MMC) started operation in 1953 with a capacity of 560 tons of electrolytic zinc per month. Its capacity has been expanded gradually and reached 8,100 tons per month in 1973. However, present production level is about 6,500 tons per month due to the depressed zinc market. In 1963, newly developed sulphate roasting was incorporated for residue treatment. Since 1973, electric power from Ohnuma geothermal power station of MMC has been supplied in addition to hydroelectric power from Komata power station of MMC. At present, about 40% of power is supplied from our company's power station and the rest is from the power company. Recent customers' demands for zinc prod- ucts include various kinds of shape, weight and chemical composition of galvanizing zinc alloy. It is necessary for zinc producer not only to meet the requirements of customers but also to enhance the value of zinc product in order to expand the market of zinc.

Jan 1, 1987

The design of a sand pump is similar in principle to that of a water pump but differs in several areas. Results of experiments on sand pump performance have been summarized and values of design parameters quoted for optimum results. Typical performance data are also Included.

Jan 1, 1973

To reflect on the early history of mining in South Australia requires considerable imagination and rashness. The people who were the chief actors in the scene have long since passed away. Accounts of their activities are hazy and debatable. A broad brush account is all that I can hope to accomplish under these circumstances. It is fitting that a picture be painted and possible lessons learnt from the achievements of our pre- Decessors.

Jan 1, 1987

Creating Value and Improving Environmental Performance by the Recovery of Valuable Products from Tailings from the Athabasca Oil Sands in Alberta, Canada

Sep 13, 2010

This paper deals with innovative techniques that have enabled personal computers to be used on the mine site to define, develop and manage an ore body resource, while being aware of the consequences to the environment. The same set of personal computer tools that are used for resource estimation, once the province of expensive workstations, can also be used by geologists, mining engineers, surveyors and environmentalists, in managing the whole mining process, including production, grade control, monthly reconciliation and stockpile management through to tailings the management, mine rehabilitation and the due diligence process of mine closure.

Jan 1, 1996

By Nichol R

- PART A The Hoppers Crossing Pumping Station is one of the principal components of the Western Trunk Sewer Project which replaces the 90 year old Main Outfall Sewer and will convey 60% of Melbourne's sewage flow from Brooklyn to the Board's Farm at

Jan 1, 1987

The Hellyer deposit, hosted in the Cambrian Mt Read Volcanics, displays features typical of volcanogenic massive sulphide orebodies. These include a well developed stringer zone, metal zonation within the orebody, a polymict volcaniclastic sequence flanking the deposit and a hangingwall alteration plume in overlying basaltic pillow laves.Mapping and core logging is very detailed in order to extract as much data as possible from the deposit and its host rocks. A geological log suitable for direct computer input was adopted shortly after the deposit's discovery.

Jan 1, 1990