Search Documents

By M Z. Abzalov

Drilling mineral sand deposits has specific challenges, which are different from drilling hard rock deposits: Drilled sequences are represented by non-consolidated free-flowing sands to semi-consolidated clayey sands and indurated layers. Valuable heavy minerals (ilmenite, rutile, zircon, leucoxene) have an average density of 4.6 g/cm3, which is significantly heavier than the hosting sand matrix; mainly represented by quartz (density = 2.6 g/cm3). The large difference in the mineral densities can result in sample segregation in the drilling rods and capturing devices causing biased composition of the recovered samples. The drilled strata can contain beds of consolidated sediments, hard pan lenses and concretions. Therefore, chosen drilling equipment should be flexible and permit a switch from drilling the free-flowing sands to hard rock drilling. Thickness of the sand hosted mineralisation varies from several metres to more than 170 m. Mineralisation is distributed above and below the water table. Evaluation of the mineral sands deposits is based on hundreds of drill holes and many thousands of samples, therefore drilling methods should be fast and cost effective. The drilling methods commonly used for mineral sand deposit evaluation, include aircore, triple tube diamond and sonic; including its variants, such as vibrocore drilling technique. The ability of the studied drilling techniques to properly address the above listed challenges in mineral sand deposits, whilst maximising the quality of the obtained samples has been compared in three deposits: Corridor Sands (Mozambique), Richards Bay (Republic of South Africa) and Fort-Dauphin (Madagascar).This study has shown that aircore samples tend to be negatively grade biased, underestimating the heavy minerals content, in particular when drilled intervals are located below the water table. Triple tube diamond core method can produce non-biased samples. However, results can be marred by incorrectly chosen drilling mud. Sonic drilling is a relatively new technique based on a high frequency vibratory technology. It is the only production drilling technique that allows a continuous relatively undisturbed sample of unlithified sands to be obtained. The main limitations of this technology preventing its wider use for developing mineral sand resources are the relatively high drilling costs, in particular when the depth of drilling exceeds 100 m, and speed of drilling advance.

Oct 5, 2011

By F Carrick, W A. Ellis, D R. Mulligan, S I. FitzGibbon

"One of the major environmental impacts of mining is the destruction of habitat. The koala (Phascolarctos cinereus) is an iconic Australian marsupial that has been severely affected by land clearing and its decline is continuing. This has placed pressure upon mining companies and government agencies to ensure koalas are managed throughout the life-of-mines - from land clearing through to rehabilitation of post-mining landscapes. This paper reports on the æKoala VentureÆ research partnership between The University of Queensland and Rio Tinto. As part of the Koala Venture program we examined koala use of two types of restored environments: rehabilitated mined land (20 sites) natural regrowth forests (six sites), at Blair Athol Coal Mine in Central Queensland, Australia. Searches for koala scats revealed evidence of koalas in ten per cent of rehabilitated sites (2/20) and 33 per cent of natural regrowth sites (2/6). Two factors were identified as being of greatest importance in facilitating koala recolonisation of restored habitats. Firstly, all recolonised sites were located close to native forest occupied by koalas (mean 135 m ¦ 52). Proximity to source animals is considered crucial to recolonisation of suitably restored habitats. Secondly, three of the four recolonised sites were dominated by koala food trees, most of which were large enough to be utilised by koalas. Availability of suitably abundant food resources is, therefore, also considered crucial. The requirement for these two factors, in combination, is highlighted by the absence of koalas at several sites that contained abundant food trees, but that were distal to areas with source animals, and vice-versa.Our research demonstrates the enormous potential for restoration of wildlife habitat on post-mining lands, even for species with specific requirements such as the koala. Consideration of the ecological requirements of wildlife during rehabilitation planning is critical to enhancing the likelihood of recolonisation.CITATION:FitzGibbon, S I, Ellis, W A, Mulligan, D R and Carrick, F, 2012. Rehabilitating post-mining landscapes for wildlife - A case study from the Koala Venture research program in Central Queensland, in Proceedings Life-of-Mine 2012, pp 319-324 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By Girnau G

The necessity of effective dust suppression measures during excavation work is just as uncontroversial in tunnelling as it is in mining. In many respects, in fact, the applied technology is comparable. Notwith- standing, given more careful appraisal, it becomes evident that very different starting conditions exist in both these fields: In mining, there are for instance, well organised firms, which in many cases have been active for several decades, carrying out the required drivage and winning operations - and although there are also experienced firms in tunnelling, these generally speaking form a joint venture in order to accomplish a certain project. These "tunnelling firms" which are formed for a short term, normally only exist for a period of two-to three years. They con- stantly reorganise themselves: from the site supervising engineers by way of the foremen and shift overseers to the gangs working on site. The "firm's headquarters" are also re- located when a new project is started up. Then of course, there is often pronounced fluctua- tion among the crews of a single tunnelling project. Seen from this point of view, a safety expert in tunnelling has a far more difficult task than one in mining. He has not the advantage of knowing every corner of the mine for years if not decades on end, of being familiar with the overall organisation of the enterprise let alone knowing many of the men at the face. This ideal prerequisite for effec- tive decisions pertaining to suitable measures for industrial safety and accident prevention taking all weaknesses into consideration given the interplay of the most varied system com- ponents, can practically only be arrived at in mining.

Jan 1, 1987

By B Abbasi

It is well known that most roof falls in coal mines typically occur at and around intersections. Room-and-pillar and longwall coal mining systems typically develop 3-way and 4-way intersections. This research develops an improved scientific understanding of stress distribution and associated instability behaviour around 3-way and 4-way coal mine intersections through 3-D numerical modelling and limited field observations. Numerical analyses were performed for an Illinois longwall coal mine to identify factors that influence intersection stability. The stability of immediate roof, floor strata, and coal ribs at and around intersections are considered with pre-mining regional horizontal stress. Non-linear failure analyses used the Hoek-Brown failure criterion for rock mass. Progressive failure zones in and around intersections were developed. For a typical 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of the immediate roof and floor layers. The mechanism of failure is similar for a 3-way intersection but the shape and extension of failed zones differ. For the 3-way intersection, the effect of off-set distance was analysed. It was found that minimum off-set distance of about 10 m (centre to centre distance between two 3-way intersections) was required to minimize interaction between two intersections. A simple instrumentation program monitor ground movements around intersections. These data were used to design the intersection geometry that is now being practiced by the mine. CITATION:Abbasi, B and Chugh, Y P, 2018. Instability analysis in three-way and four-way coal mine intersections, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 345–359 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A G. Tomkins

"Approximately 32 per cent of the worldÆs total gold production has come from greenstone belts (Frimmel, 2008). In these regions numerous small to large, quartz vein-associated gold deposits are hosted in metamorphic rocks ranging from lower greenschist to granulite facies. Historical exploration has focused its efforts on rocks of greenschist to lower amphibolite facies because these seem to contain the most deposits. Consequently, these regions are now reaching mature brownfield status, particularly in developed nations, and finding new deposits is becoming progressively more difficult. In comparison, regions of similar tectonic setting, but instead containing high-grade metamorphic rocks of mid-amphibolite to granulite facies, have received little attention because the first explorers found fewer deposits there.However, these regions certainly do contain some very significant gold deposits such as Hemlo in Canada (~684 t Au), Renco in Zimbabwe (~31 t Au mined since 1980), the very profitable Challenger deposit in South Australia (~36 t Au; recovered + reserve + resource), and the most recently discovered Tropicana deposit in Western Australia (~182 t Au; reserve + resource). High-grade metamorphic terrains therefore offer explorationists an excellent opportunity to move onto relatively green fields within developed nations, which carry less risk associated with development. However, explorationists have comparatively little knowledge of the geological controls on gold distribution in high-grade terranes because: industry experience lies in traditional lode-style gold deposits these gold deposits are geologically more complex there has simply been minimal research conducted on these deposits as a holistic group.Furthermore, research conducted in the last five years has shown us that the previous widely accepted model for gold genesis in these terranes, the crustal continuum model, is incorrect. Here, I discuss features from several gold deposits hosted in high-grade metamorphic rocks and use these to define two categories for explorationists to consider: deposits that formed prior to peak metamorphism (metamorphosed gold deposits) deposits that formed well after peak metamorphism (post-metamorphic gold deposits). There are none that have been convincingly shown to have formed during peak metamorphism.CITATION:Tomkins, A G, 2013. Gold deposits in highly metamorphosed terranes, in Proceedings World Gold 2013, pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

Gwalia Consolidated Ltd has been in the mining industry for about 15 years, yet its key wholly owned Greenbushes Mine has a history dating back to the last century. Similarly Gwalia Consolidated's associate, Sons of Gwalia Ltd owns the historic Sons of Gwalia and Marvel Loch Mines with Sons of Gwalia celebrating its centenary this year. This durability is a testament to the quality of the orebodies concerned and the massive technological achievements over this time which have enabled each of these mines to maintain their competitiveness. While Sons of Gwalia and Marvel Loch were and continue to be gold mines, the wholly owned Greenbushes Mine has survived and in fact prospered through the development of alternative products from its rich and unique pegmatite. Similarly, for Gwalia Consolidated to grow and prosper it will be necessary to expand the current portfolio of products and operations. The Greenbushes Mine has already given Gwalia world `No 1' status in both the supply of primary tantalite concentrates and lithium minerals (spodumene). The asset base contributed by Gwalia's gold investments assisted in the recapitalisation of the Greenbushes assets to fully develop their potential. Industrial minerals and strategic metals were of interest to Gwalia as these markets are relatively small and it is possible to develop an influential if not dominant position in the market with a quality asset. Capital expenditure to develop such projects are also usually in the order of $10 m to $20 m, a manageable range relative to Gwalia's size.

Jan 1, 1996

A research and testing facility has been developed at Simtars to allow the spontaneous combustion testing of coal on a large scale. In this adiabatic reactor, the coal particle sizing is closer to that which could be found in the goaf and therefore the reaction is more likely to simulate the underground situation. This allows aspects of the spontaneous combustion process and methods for detecting a heating to be investigated which cannot be done in an operational mine. Up to 18 tonnes of run of mine or crushed coal is loaded into the reactor and allowed to self-heat while the temperature and gas profiles within the coal pile are monitored. The gases evolved from the coal are analysed using a fixed gas monitor system and gas chromatography to determine which of the common mine fire indicators and ratios can be used to predict the onset and progress of coal heatings. Benchmarking of the inherent propensity of a coal to spontaneously combust at both the large- and laboratory-scale is also possible by comparing the sample against previously tested samples. It has been found that the coal particle size affects both the time it takes for the coal to react and the location of the developing heating. The heatings generate approximately one metre from the inlet but in the crushed coal case do not progress to an advanced heating stage until the æhot spotÆ migrates towards the coal surface where there is an increased oxygen supply. Physical properties such as the compressive strength of the coal also affect the heating size and the time it takes for a heating to develop. Higher strength coals appear to oxidise more slowly and therefore take longer to self-heat as oxidation of the coal is the heat-generating step in the spontaneous combustion process. The best indicators of the state of the heating were found to be CO make and GrahamÆs ratio which are independent of air flow. Investigation of a potential spontaneous combustion should begin as soon as the CO make or GrahamÆs ratio exceed the background levels. The results from the tests undertaken on a number of Queensland and NSW coals are reported here together with the implications for the mining industry.

Jan 1, 2005

By Brigden J. F, Birrell

A regional geochemical exploration programme commenced in July 1983, based upon low-density sampling of lateritic duricrust over parts of the Yilgarn Block of Western Australia. This resulted in recognition of an area significantly anomalous in chalcophile elements that progressively led to the discovery of the Johnston Range gold deposits in 1985. The deposits, on the Barlee 1:250,000 map sheet, occur in four mineralized zones, and production is expected to commence during 1988. The programme leading to the Johnston Range discoveries was a collaborative research/ applications study between the AGE Joint Venture (Greenbushes Ltd., St. Joe Minerals, and from 1985, Sons of Gwalia NL) and the CSIRO Laterite Geochemistry Research Group (Smith, 1987). It built upon a precursor project sponsored by Greenbushes Tin Ltd that commenced in 1980 and arose from an orientation laterite research project in the Greenbushes rare metal pegmatite district (Smith et at., 1987). Both were multi-commodity programmes and included the search for gold deposits. Basic methodologies for sampling and data interpretation have been described by Smith and Perdrix (1983) and Smith et at. (1984). Continuous geochemical coverage of designated parts of greenstone belts was sought using a triangular grid of 3-km or 1-km spacing, depending upon the expected prospectivity of the areas and the size and characteristics of the ore deposit targets. First-pass sampling, that resulted in the Johnston Range discoveries, was at 3-km spacing and several samples within a 30-km by 5-km area were

Jan 1, 1988

By Smith C. B

Major diamond pipes discovered in Western Australia in the late-1970s exhibited a number of unique features that not only resulted in Australia becoming the largest diamond producer in the world in volume terms by 1986 but also changed geological thinking on the primary occurrence of diamond. They were: - lamproite is an alternative primary diamond host to kimberlite. - the extremely high mean grade of the Argyle lamproite pipe at 5 ct per tonne. - the tectonic setting of the lamproite pipes in mobile zones mar- ginal to the Kimberley Craton in contrast to the traditional African setting within stable cratons. Diamond was one of the earliest economic minerals discovered in Australia but 128 years elapsed between its first recognition and the first Australian economic pipe discovery (Argyle). During that period some 200,000 ct of alluvial diamonds were mined in Australia (mostly in New South Wales), but such alluvial output is insignificant on the world scene where annual production today runs at 95 million ct of natural stones some 76010 of which comes from primary pipe sources such as Argyle which alone produces 30 million ct per annum. Of particular significance therefore is the geological nature of the primary diamond source rocks in Australia. The Argyle and Ellendale Pipes are lamproites, differing from kimberlite in their mineralogy and geochemistry, and characterised by the presence of typical lamproite minerals such as leucite, priderite, potassic richterite, and the abnormally high content of chemical elements incompatible with ultramafic rocks. But not yet widely appreciated is that many other Australian olivine-rich lampro- phyres also contain diamond. Such picritic alkaline rocks can

Jan 1, 1988

By L Yang, L Chen, E Hu, D Tang

Online monitoring of particles cumulative percent passing (PCPP) for a target size at hydrocyclone overflow, compared with traditional offline methods, provides PCPP feedback in real time, and is advantageous in enabling energy-efficient comminution, increasing downstream flotation efficiency, and improving upstream resource knowledge. However, existing online approaches are generally costly and bespoke, and some are sensitive to operational changes. Therefore, this study proposes a new low-cost alternative based on accelerometer measurement for online PCPP monitoring in the overflow of hydrocyclones and provides a preliminary experimental investigation under dry condition. The proposed method uses a sensing probe inserted into the overflow pipe of a hydrocyclone to receive particle impact from the incoming slurry, with accelerometers attached to the probe and mounting frame outside the pipe for particle-probe impact detection. As a preliminary investigation before studying particle-probe impact events in slurry, tests under dry condition without fluids were conducted using dry sand particles in free fall from a fixed height. Accelerometer measurements are analysed in both time and frequency domains through root-mean-square (RMS) and fast Fourier transform (FFT). Results show that accelerometer measurements are useful in estimating mass flow rates, which are correlated to the accelerometer output amplitude RMS values in time domain, in a non-linear mapping. Different particle size classes can be identified by examining the accelerometer output amplitude at a known mass flow rate. Different particle size classes feature their distinct signature frequencies (SFs) that can be examined via FFT and the SF is found to be independent of the mass flow rate. The results imply that any PCPP changes can be detected by the change in the accelerometer output amplitude as well as a shift in SF, which demonstrates the effectiveness of using accelerometers to gauge changes in PCPP. Based on the current findings in dry condition, future work will investigate particle-probe impact events in slurry.

Aug 24, 2022

By C I. Edwards

Phosphorous is typically present in iron ore either in the mineral apatite, Ca5(PO4)3OH, or associated with the goethitic fraction of the ore. In this paper, we present results that show that phosphorous associated with the goethitic fraction can be removed with a heating pretreatment around 300 176;C for 1 h, followed by a caustic leach with 1 - 5 M NaOH, or a leach with sulfuric acid at pH 0.5. The heating pretreatment is considered to dehydroxylate the goethite to form a haematite intermediate phase, ‘protohaematite’, that reacts during the leach making the phosphorous accessible to the leachant. In the acid leach, ten to 15 per cent of the sample was dissolved to obtain a leach product with 0.08 per cent P. In the caustic leach, as no weight loss occurs, it is proposed that iron species associated with the protohaematite have either not dissolved or have reprecipitated at the high pH values of the leach.For an ore containing apatite as the source of phosphorous, a leach with sulfuric acid dissolved the apatite, lowering the phosphorous levels in the sample. The sample treated contained carbonate minerals (including siderite) that also reacted with the acid, and in practice a balance between the dissolution of the apatite and the carbonate minerals may be needed to minimise acid consumption.

Jul 11, 2011

By D Matthews

With the increasing demand for quality-specific ores, coupled to the reality of even more complex minable iron ore reserves, there is a growing need for real-time online material analysis of plant feed and product. For a full system mass balance, the combination of conveyor weight scales, flow and density transmitters are required. This alone does not guarantee product grade. For optimal process control and material blending, real-time online elemental scans in combination with the mass weighting is becoming more than a ‘nice to have’. These elemental scans located at key positions, enable the mining and plant operators to make informed decisions timeously, therefore ensuring product outcomes and optimising operations where material grade and the control thereof are important. Typically, these units follow the mining and primary crushing circuit as well as on the product conveyors, low-grade conveyors and tailings lines. Deployed after the primary crushing circuit, an analyser acts twofold:1. guaranteeing mining production, and2. processing facility feed blends.The analysers on the product conveyors guarantee saleable product. The analysers on the low-grade conveyor and tailings line complete the elemental balance and identify the potential of the low-grade and tailings for future processing. The system losses (accumulation) are calculated to determine the amount of material ‘lost’ during the processing stage which does not report to any of the aforementioned and can be used as a measure of the efficiency of the plant. A further advantage of the real-time online analysis of material is that immediate intervention can be taken in the event that the product is not of saleable product grade requirements. In the Khumani Iron Ore mine, Northern Cape, South Africa, run-of-mine (ROM), product and control analysers were included. Run-of-mine and product stockpiles are certifi ed, low-grade material is not currently directly measured, but calculated from the internal control loops. Iron units are reconciled between product and feed material.

Jul 11, 2011

By J Zhou

Gold in sulfide ores is associated predominantly with sulfide minerals and occurs as both microscopic and submicroscopic particles. In non-refractory sulfide ores, gold occurs mainly as coarse- and medium-grained particles. Minute inclusions and submicroscopic gold usually account for a minor portion. In contrast, gold in refractory sulfide ores occurs mainly as minute particles and submicroscopic gold, and microscopic gold usually accounts for an insignificant portion. In gold ores containing carbonaceous material, the preg-robbing nature of carbonaceous material may impose challenges on gold extraction and cause gold losses. To extract gold from refractory sulfide ores, the ore needs to be finely ground and preoxidation is often required. Sulfide host minerals must first be oxidised to create a porous structure through which the cyanide leach solution can penetrate to reach the colloidal gold particles. The oxidation is traditionally achieved by roasting, autoclaving or bacterial oxidation. In carbonaceous sulfide ores exhibiting a preg-robbing nature, the carbonaceous material needs to be treated by roasting, autoclaving or other means to minimise the preg-robbing effect. As a predictive and troubleshooting tool, the gold deportment study plays an important role in gold metallurgy. It determines the deportment of gold in an ore or mill product and identifies the mineralogical issues that may affect or may have affected gold extraction. The information acquired from a gold deportment study can be used to assist in process selection, flow sheet development, recovery improvement and reagent optimisation.CITATION:Zhou, J, 2013. Deportment of gold in sulfide ores and implications for gold extraction, in Proceedings World Gold 2013 , pp 433-442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G F. Brent, S Hawke, M Rothery, P Dare-Bryan

Mine-to-mill studies have previously demonstrated downstream productivity benefits from relatively modest increases in blast energy, or powder factor. These increases have up to now been limited by safety and environmental constraints, since excessive blast energy can result in flyrock, unacceptable vibration, airblast and wall damage.Here, a new blasting method that overcomes these constraints is presented. For the first time it is possible to employ powder factors that are several fold higher than conventional blasting. Independent modelling has shown that such powder factors can potentially increase mill throughput by 20 to 40 per cent. The economic implications are substantial, both in terms of increasing production in existing operations and in consideration of capital and plant requirements for greenfield sites. In addition, mill electricity and grinding media consumption and their associated costs and energy and emissions penalties can be reduced.This method represents a step-change in blasting practices. It involves a novel design utilising dual blast layers within a single blast event, all initiated with state-of-the art electronic blasting systems. The energies in the lower layer can be as high as five times the standard energies, providing for intense fragmentation of the ore. Results from blast models have been confirmed in field trials of the method.Open cut gold mining, in particular, stands to benefit from this method. As gold grades decline, milling costs and throughput increasingly become constraints on production that can be alleviated with this new method. Additionally, it opens possibilities for improved recovery. Blast modelling studies show that dilution of gold ore within the blast can be managed with the new method. Furthermore, it has been shown that vibration from the new method is actually lower than from conventional blasting, allowing the use of the technique in proximity to mine highwalls and other key infrastructure such as underground orepasses.It is concluded that this new method could substantially increase gold mine production and profitability while reducing overall energy consumption and associated emissions.CITATION:Brent, G F, Dare-Bryan, P, Hawke, S and Rothery, M, 2013. Ultra-high-intensity blasting - a new paradigm in mining, in Proceedings World Gold 2013 , pp 395-400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Booth S. A, Milton D. W

Stratabound/stratiform and remobilised mineralisation have been recognised as the two dominant styles of mineralisation which constitute the Broken Hill ore deposit. Recognition of prospective sites for accumulation of ore depends on understanding the heterogeneity of the ore environment and the distribution of the two styles of mineralisation. The internal stratigraphy of the Broken Hill ore deposit and its enveloping rocks, is described, and a generalised stratigraphic setting of the stratiform mineralisation is outlined. Fhiphasis is placed on the existence of closely-spaced sub-basins as potential sites for ore accumulation close to the Broken Hill ore deposit. Further from the immediate ore environment, recognition of the same diagnostic stratigraphic sequence

Jan 1, 1983

By M Barden, G Lane, B Quilliam

NQ Minerals PLC, through Hellyer Gold Mines Pty Ltd, plans to reprocess the contents of the Hellyer tailings dam to produce lead/silver concentrate, zinc concentrate and pyrite concentrate (containing Au and Ag). This paper discusses the project development, mineralogy, metallurgy and chemistry of processing Hellyer tailings and the associated environmental benefits. The Hellyer and Fossey orebodies were volcanic hosted polymetallic massive sulphide deposits located within the Mount Read volcanic arc of western Tasmania. Mineralisation was hosted in massive sulphide (pyrite) and comprised predominantly of sphalerite, with lesser galena, chalcopyrite and arsenopyrite. The Hellyer orebody was mineralogically complex (fine grained) and was treated through differential flotation with initially modest recoveries. Fossey ore processing characteristics were similar to those of Que River ore and simpler than Hellyer but treatment still resulted in significant grades in flotation tailings. CITATION: Lane, G, Barden, M and Quilliam, B, 2018. Hellyer tailings – complex mineralogy but higher grade than many ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 35–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By P Breuer, A Simons

The sulfidisation, acidification, recycle and thickening (SART) process is currently being used at NewcrestÆs Telfer Gold Mine to recover cyanide and copper from the cyanidation tails of the pyrite concentrate carbon-in-leach (CIL) process. While the process has been effective at attaining high recoveries of cyanide and copper, the Telfer SART plant has experienced higher than expected sulfide additions to achieve these recoveries. This paper details the results of surveys on the Telfer SART plant, which show that residence time appears to be causing the high sulfide consumptions. The paper also details the results of laboratory scale experiments which confirm the observed residence time impact during the acidified stage of SART.CITATION:Simons, A and Breuer, P, 2013. The impact of residence time on copper recovery in Telfer Gold MineÆs cyanide recycling process, in Proceedings World Gold 2013 , pp 189-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P Breuer, X Dai, A Bergamin, D Hewitt

"Copper-ammonia-thiosulfate?leaching of gold has been researched for several decades as a potential alternative to cyanidation. However, this technology has not yet been applied commercially due to many challenges such as complex solution chemistry, reagent degradation and losses, system instability with losses of precious metals and difficulties in gold recovery from the leachate. Progress has been made at CSIRO in tackling some of these challenges including:better understanding and control of the leach conditions to minimise reagent losses whilst maximising gold recovery use of strong base ion exchange resins to recover the gold strategies to deal with polythionates that adsorb competitively with gold on ion exchange resins development and evaluation of process flow sheets.As a result there has been increased interest from the gold industry and renewed activities to develop thiosulfate based processes for gold recovery. One application area, which has been developed to the point of piloting, is the treatment of gravity gold concentrates using a copper-ammonia-thiosulfate leach with ion exchange recovery of the gold thiosulfate. This paper describes some of the advancements in the development of a potential process flow sheet for this application.CITATION:Dai, X, Breuer, P, Hewitt, D and Bergamin, A, 2013. Thiosulfate process for treating gold concentrates, in Proceedings World Gold 2013, pp 61-70 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By R Brake

The Enterprise Mine (EM) is located at Mount Isa and is wholly owned by Mount Isa Mines Limited (MIM). This high-grade copper mine extends from about 1000 m below surface to almost 2000 m below surface. A recent $400 million upgrade has taken the operation from a production rate of 1.3 Mtpa to a capacity of 3.5 Mtpa. The effects of high surface ambient temperatures in summer, combined with the depth of the mine and high virgin rock temperatures results in heat stress in the working place that, without intervention, would exceed the levels that human physiology can withstand. It would also result in significant decreases in productivity and high accident rates even where work is possible. Moreover, with a very hot and deep mine, the needs of æegressÆ and entrapment of workers during a mine emergency must be carefully considered. Enterprise Mine has taken a æsystems approachÆ to the issue of working productively, healthily and safely in heat. This involves setting limits of thermal stress for workers, understanding productivity decrements when working in heat, establishing productive and healthy environmental targets, developing engineering solutions to meet these targets, creating a well-educated workforce with respect to working in heat and then developing health protocols to ensure workersÆ health is protected. Refrigeration must be added to the mine to provide acceptable and productive conditions underground. By the time the mine is commissioned in 2000, Enterprise mine will have an installed refrigeration capacity of in excess of 40 MW(R). The ventilation engineering principles proven over many years at the other Isa underground mines are tailored to æfloodingÆ the mine with air to remove the heat, which is the main contaminant. This principle will not work at the Enterprise Mine, for reasons discussed below. With the underlying ventilation principle no longer satisfactory, a complete review of the entire ventilation principles and engineering solutions was required for the Enterprise Mine.

Jan 1, 2000

By J Zhou, T D. McGrath, K P. Galvin, C P. Lowes, J J. Eksteen

Pre-concentration of low grade ores can improve the economic and environmental sustainability of an operation significantly, with opportunities for implementation ranging from run-of-mine to mill discharge depending on ore specific characteristics. For a gravity separation, where the performance is fundamentally constrained by mineral liberation, these feeds often represent a very difficult separation given the dominance of the relatively coarse gangue and fine liberation sizes. Thus, building knowledge of the feed through characterisation of the density distribution is critical to assessing amenability before progressing towards lab/pilot-scale test work and full-scale operation. The traditional approach to determining the density distribution typically involved sink/float testing, however, recent developments in hydrodynamic fractionation using inclined channels now offers a more cost-effective alternative with minimal health and environmental risk. A non-hazardous dense liquid, namely an aqueous solution of lithium heteropolytungstates (LST), is supplied as fluidisation to a REFLUXTM Classifier, consisting of a vertical section below a system of inclined channels, operating in semi-batch configuration. Fractionation is achieved by increasing the flow rate incrementally and collecting the particles to form a series of flow fractions. The purpose of this paper is to present this new method in the form of a case study, aimed at assessing the amenability of a low grade gold-bearing sulfide ore to pre-concentration. The robustness in the method is demonstrated through comparison with sink/float data, examining the density distribution and the liberation-limited product grade and recovery achievable. These data are then used as a benchmark to assess water-based continuous gravity separations conducted on the feed using a laboratory-scale REFLUXTM Classifier. This data set is used as the basis for process modelling and empirical validation for the recently established partition surface of the separator.

Nov 10, 2020