Search Documents

By J Ramezani, K Faure, N Mortimer

Western New Zealand can be regarded as a rifted continuation of eastern Australia. Detailed studies of units previously considered to have trans-Tasman correlations are being undertaken within the FRST Programme Mineral Wealth of NZ and its EEZ to test specific connections, and thus add to the exploration framework of NZ. Correlation of two major episodes of granitic magmatism are currently being investigated. These represent the oldest (mid Paleozoic) and youngest (Early Cretaceous) magmatic events that conjoined Australia and New Zealand are believed to have in common.

Jan 1, 2007

By D F. S Natusch, R J. Hooper

Recent lignite investigations indicate their potential as a strategic long-term fuel resource. This potential however would be determined not only by lignite quantity and quality, but also by economic, physical and social resources required to support it. The following discussion uses the example of a typical lignite mining operation to review the major resource requirements. While recognising that the implications of supplying those resources may be as important as their actual existence, this paper has purposely omitted such discussion as this will be one of the main target areas for the next phase of investigations.

Jan 1, 1983

By M I. Pownceby, S Hapugoda, V Nunna

Deposits of low-grade iron ores containing abundant goethite are distributed across the world. A common difficulty associated with beneficiating goethitic-rich ores is the poor liberation characteristics of the iron-bearing minerals which often contain finely disseminated gangue minerals such as kaolinite, gibbsite and quartz. Microwave-assisted heating has been proposed as an effective way of inducing dehydroxylation and associated mineral transformations in order to beneficiate low-grade goethitic ores. In this research, the mineral transformations occurring in a low-grade goethite-rich sample using microwave radiation was studied. Roasting conditions (up to 1000°C and under various CO/CO2 gas atmospheres) were designed to generate a magnetic product from a goethite-rich, reject waste stream sample sourced from an iron ore processing site in the Pilbara, Western Australia. Conditions (T, pO2) for transforming the raw material from hydrated goethite to hematite and eventually to magnetite are presented. Chemical and mineralogical characterisation of the raw material and roast products were conducted using X-ray fluorescence, X-ray diffraction, optical microscopy and scanning electron microscopy techniques to identify the mineralogical and chemical changes occurring during the heat treatment. Further steps are suggested to optimise the microwave-assisted magnetising roasting and correlate it with the application of magnetic separation techniques to maximise the efficiency of upgrading the iron content in low-grade iron ores.CITATION:Nunna, V, Hapugoda, S and Pownceby, M I, 2017. Study of microwave-assisted magnetising roasting and mineral transformation of low-grade goethite iron ores, in Proceedings Iron Ore 2017, pp 575–582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By K Faure

At Sams Creek a gold-bearing, peralkaline granite pophyry dike intrudes Ordovician-Silurian metapelite and quartzite. These metasedimentary rocks have undergone three phases of folding: a first phase of recumbent folds (F1), a second phase (F2) of northerly-trending inclined folds with a prominent crenulation cleavage, and a third phase (F3) of steeply plunging folds. The granite porphyry dike has a thickness of up to 40 m and intrudes thin lamprophyre dikes along its contacts. Deflection of the crenulation cleavage around the granite dike, shearing within the dike and its sinuous outcrop pattern indicate that the granite dike has been deformed during F2 and F3. The granite has been hydrothermally altered, with a first stage of magnetite-ankerite alteration. This first stage is cut by a second stage of quartz-pyrite veins and a third stage of sulphide, quartz and ankerite veins, accompanied by pervasive silicification represented by quartz-perthite-albite-rutile¦pyrite-ankerite-sericite assemblages. Lamprophyre is altered to an ankerite-chlorite-sericite assemblage. The sulphide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite. The altered granite and the veins have been deformed and recrystallised. The competent sulphide minerals pyrite and arsenopyrite are fractured and brecciated, with fractures locally filled by galena, a ductile sulphide mineral. Vein quartz shows local cataclastic and mortar textures and develops pressure shadows around arsenopyrite. Alteration and mineralisation are confined to the granite porphyry and adjacent lamprophyre. These features together with the style of veining and the sulphide mineralogy indicate that the mineralisation was formed from a magmatichydrothermal fluid that was sourced from the granite. Oxygen, carbon and sulphur isotope values of the vein minerals (quartz, ankerite and sulphides) are also consistent with a magmatic source.

Jan 1, 2003

By A G. Cuison, B V. Andam

Three well-known copper and gold deposits in northern Luzon, Philippines are located in the Mankayan Mineral District. These are the Lepanto Copper-Gold Deposit, the Far Southeast Porphyry Copper Deposit and the newly discovered Victoria Gold Deposit. The latter discovery led LCMC to shift from a predominantly copper mine to a gold mine. The pre-Eocene Lepanto basement andesite and the middle Miocene Balili volcaniclastic sequence underlie the Mankayan Mineral District. They are intruded by tonalitic to gabbroic Bagon Intrusive followed by diorite-quartz diorite intrusions. Diatreme emplacement of late Miocene-early Pliocene Imbanguila dacite pyroclastics and porphyries took place much later. Faults in the district mostly form a conjugate fracture pattern dominated by north and northwest trending shears, east-west trending extensional fractures and few north-south trending fissures. Victoria is an epithermal gold-base metal rich quartz vein deposit. The veins occur along tensional structures and it is common to observe crustiform and banded features among the sulphides and gangue minerals. It is an open space infilling type of mineralisation. The Victoria vein systems are divided into zones based on continuity. In each zone are major veins and associated spits. Dacite pyroclastics and porphyries predominantly host the major veins with a few narrow veins hosted by the Balili volcaniclastics and the Lepanto metavolcanics. The veins generally trend east-northeast with 75 - 80 dips towards the south. The longest vein can be traced fairly continuously for a horizontal distance of about 600 metres. The vertical persistence of major veins exposed on three level drives has a range of 150 metres and can reach as much as 400 metres based on drill hole intercepts. The vein widths vary from two to eight metres. Right lateral movements of either the NW or NE shear faults could have produced the east trending tensional fractures. The development of ore shoot patterns was recognised and has been helpful to the mining operations. Cymoid loops with defined pinch and swell features are noted both laterally and vertically. Complementing the structural pattern is the distribution of gold values along veins where lateral and vertical continuity is also observed. Gold is associated with quartz, sphalerite, galena and chalcopyrite. In relatively high gold zones, the abundant sulphides are sphalerite and galena. In relatively high copper zones, there is an abundance of chalcopyrite and tetrahedrite. Galena is always associated with sphalerite but less in abundance. Chalcopyrite occurs either as separate bands from or associated with sphalerite-galena. Chalcopyrite and tetrahedrite appears contemporaneous with sphalerite and galena but in some portions the former cuts the latter sulphides. The predominant gangue minerals are quartz, carbonates and gypsum. Rhodochrosite is the predominant carbonate gangue. Few sulphides are found in the carbonates. Gypsum (anhydrite) is found cross-cutting early mineralisation. It carries very few sulphides. The alteration halos around veins are relatively narrow. In an outward sequence, the silicic alteration occurs very near the veins, followed by sericitic-argillic alteration then to propylitic zones. It is also common to observe veins bounded by propylitic alteration. Preliminary paragenetic studies show apparent three stages of mineralisation, the early-quartz (-gold) stage followed by a carbonate stage and a late-gypsum stage. The abundance of base metals relatively decreases towards the gypsum stage. The Victoria gold deposit could have some genetic associations with the Lepanto Cu-Au deposit and probably indirectly with the FSE porphyry system. It is relatively apparent that the Victoria quartz-gold-base metal veins could have occurred similarly as the quartz-gold roots overprinting the Lepanto enargite mineralisation. This overprinting signifies the waning stages of the entire hydrothermal system.

Jan 1, 1999

Bubble Load Measurements in Flotation - A Critical Review of Current Practice

Sep 13, 2010

Industries in the Kwinana area have embarked on a journey of improving the eco-efficiency of Western AustraliaÆs primary heavy industry area. The Kwinana Industrial Area has some unique characteristics that provide both opportunities and barriers. The Kwinana Industries Council and the Chamber of Commerce and Industry are working with the industries to identify a range of projects that can deliver improvements for both environmental and economic æbottom linesÆ, and to progress these projects using internal and external resources. The evolution of the process, its relationship to the ethos of operating companies, and the availability of resources to pursue projects, is an interesting study with lessons for others interested in taking the same course.

Jan 1, 2002

In November 1969, New Zealand Steel Ltd pioneered the commercial use of the SL/RN solid fuel direct reduction process to make sponge iron as a feed material for electric arc furnaces. Serious process problems with the use of green balls and coal injection were progressively overcome. The process was developed by New Zealand Steel along a radical route, of feeding the fine grained raw ironsand concentrate and coal directly to the kiln. Contemporaneously with this development of direct reduction, steelmaking process innovations were made that enabled the arc furnaces to operate successfully with the high volumes of acid slag. The further expansion of New Zealand Steel's primary steelmaking capacity to replace the currently imported hot and cold flat rolled products is under consideration. The requirement to produce about 600 000 tonnes of steel slabs will be an opportunity to further modify iron and steel making plant and processes to optimise the economics. The conceptual and preliminary engineering selection of options is described.

Jan 1, 1980

Comparison of Discretised Population Balance (DPB) and Finite Element Method (FEM) Methodologies for Modelling Batch Gibbsite Precipitation

Sep 13, 2010

Flotation Performance Improvement by Air Recovery Optimisation on Roughers and Scavengers

Sep 13, 2010

By S G. Keyte

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.l mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass Yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80 per cent and mass yields of less than one per cent can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

This paper presents an analysis of the production data for the period 1861 - 1953 from hydrothermal gold-silver deposits of the Hauraki Goldfield. To directly compare the metal content of the deposits a figure of ounces of gold equivalents (oz gold equivalent) is calculated from the value of the gold-silver bullion produced from each deposit. Frequency distributions for ore tonnage and oz gold equiv. appear to be lognormal and show a high proportion of very small deposits, with 90 per cent less than 100 000 tonnes. The deposits when plotted in order of size fall roughly on a smooth curve which suggests that the size distribution is not random. A large proportion (68 per cent) of the total gold-silver extracted from the Hauraki district was contained in the largest deposit û Waihi. A technique used for predicting undiscovered mineral resources is ZipfÆs law, which relates the size of an item to its rank order. The figures for ounce gold equivalents from the major Hauraki deposits fit ZipfÆs law remarkably well. Taking Waihi at 6.8 million oz gold equivalent as the rank one deposit, Thames is number five and Karangahake number seven. A Zipf plot indicates that down to rank 100 (68 000 oz gold equivalent) only 28 per cent of the total gold-silver resource in the Hauraki Goldfield has been extracted. A further 72 per cent or 25.4 million oz gold equivalent, including the deposits of rank 2, 3, 4, 6, 8, 9 and 10, are undiscovered. However, since some deposits will be deeply buried under younger rocks and others will be under the sea only a proportion of the total resource will be discoverable.

Jan 1, 1981

By S Moradi

The aim of this study was to investigate the possibility of leaching zinc from the tailing (-2 mm) of Angouran flotation plant using sulphuric acid. The tails were first calcined at 800¦C for one hour. The effect of factors such as stirring rate, temperature, initial acid concentration and solid/liquid ratio, on zinc extraction were studied. The results obtained show that at the best conditions, about 91 per cent of zinc were leached using a stirring rate of 800 rpm, a reaction temperature of 50¦C, a 30 minute reaction time, a 100 g/L initial sulphuric acid concentration and solid:liquid ratio 1:6 g/ml. The P85 of the feed material was about 150 ¦m and acid consumption was 600 kg/t.

Jan 1, 2002

By S Smit, P J. J Strobo

ZINIFEX Century Mine is a zinc, lead and silver concentrate producer. Flotation is the primary method of minerals separation in this circuit. The flotation circuit is quite large with 79 flotation cells. The levels in each of these interconnected cells are controlled at more than 45 level control stations. Due to the multivariable interaction throughout the circuit, good level control was found to be difficult to achieve by just using normal Proportional-Integral-Derivative (PID) control. As a first step in advanced process control, the FloatStar Level Stabiliser, a multivariable controller developed specifically for flotation circuits, has been commissioned at Century mine to solve the level control problems. The first section of this paper therefore discusses and shows the results and improvements obtained by using the FloatStar level stabiliser. The results and benefits of the FloatStar Flow Optimiser are discussed in the second section of this paper.

Jan 1, 2004

The Coal Resources Survey commenced in 1974 as a search for Huntly Power Station coal, but soon developed into the most detailed regional coal search programme to be instituted in New Zealand. The program was initially conceived as geological in nature, but later included geotechnical, geohydrological, mining assessment, coal use, and environmental considerations in its investigations. The programme never undertook development work but has provided Government and the private sector with a sound basis for identifying development options. The discovery of large-scale coal resources in the Mokau, Waikato, and Taranaki regions and the lignite resources of Otago and Southland are a measure of the Survey's success. The directive by Government to phase out the NZCRS to a large extent coincides with the completion stage of the program. With most of the detailed regional study finished, it now remains to collate the data and publish summary reports at Coalfield and Coal Region level, in order to maximise the use and value of the data collected over the years.

Jan 1, 1987

By J D. St George

In this paper a laboratory investigation into the effect of confining stress, water content and gas desorption on coal permeability is presented. Of major significance is the effect of coal permeability on outburst occurrence and methane production, which is influenced by changes in stress. Test results indicated that the shrinkage of the coal matrix associated with desorption is greater than the coal matrix compressibility which will cause a reduction in the effective stress, hence increasing coal permeability.

Jan 1, 1998

By F H. S dosSantos, R L. C Santos

The main objective of this work was to develop, at a laboratory scale, a process for treating residues from the settling stage of water treatment so as to remove and recover the aluminium as sulphate. The chemical analysis of residues from different water treatment plants indicated that the aluminium content varied from 15 to 20 per cent w/w. By using the appropriate experimental conditions, it was found to be possible to leach most of the aluminium content. The pH value of the recovered water was suitable for it to be recycled to the water treatment process and the residue appears to be suitable as raw material for bricks. The process developed contributes to the sustainability of the water treatment process.

Jan 1, 2002

By T F. McConachy, B I. A McInnes, R A. Binns

Within the last decade, major research discoveries have been made in the submarine realm of magmatic and hydrothermal activity of arc-backarc systems in the southwestern Pacific. These include identification of numerous particulate-poor, gas-rich (CO2-CH4) hydrothermal plumes emanating from arc front volcanoes, actively forming porphyry-copper-gold style mineralisation, and new backarc spreading systems erupting alkali basalt-trachyandesite magmas. Major goals of these studies have been identification of modern analogs to ancient volcanogenic massive sulfide ore bodies, and quantification of the volatile fluxes though supra-subduction zone systems.

Jan 1, 2002

In March 1990, Heritage Mining conducted a 2000 line km high resolution aeromagnetic survey of all its prospects in the Coromandel Peninsula. One of the areas covered was the Onemana Peninsula, situated about 5 km north of Whangamata. Details of location and geology are given by Robson and Stevens (this volume).   The detailed helicopter-borne magnetic and radiometric survey over the Onemana area consisted of 163 line kmÆs of flying, and was carried out in order to assist in the definition of hydrothermal alteration and pre- or post- mineralisation structures. The line spacing chosen was 100 m, flown east-west, with a mean sensor terrain clearance of 80 m. Tie lines were flown north-south every kilometre for levelling purposes. The sensor was a Geoinstruments G-813 proton precession magnetometer in a towed bird, with data recorded using a Geoinstruments G-2000 acquisition system.   The Onemana alteration system is at the northern end of a major north-north east trending structural corridor defined by regional aeromagnetic surveys performed by AMOCO in 1980 (Rabone, 1991). T his structure hosts a number of other extinct hydrothermal systems including Karangahake and Golden Cross. In the Onemana contour plot the predominant north-northeast structures form the boundaries of a large area of subdued magnetism in the southern part of the surveyed area that is caused by intense hydrothermal alteration. This area is about 3.5 km long by 1 km or more wide and contains outcropping sinters and hydrothermal eruption breccias, as described in Robson and Stevens. A number of other structures transect this alteration zone, with strike directions ranging from northwest to north. A northwest feature notably truncates the zone to the south, while the northern end seems to be simi1arly bounded; however as data coverage ends at the coast, this feature is less conclusive.    Two distinctive types of strongly magnetic rock were discernible the contoured data. The strong negative magnetic anomalies the north and west are caused by fresh negatively magnetised rhyolites. This was confirmed by ground follow-up work that showed the rocks to be fresh biotite rhyolites with high magnetic susceptibilities.

Jan 1, 1991

By D Johnston

Within the first full year of BarrickÆs Cowal Gold Mine operation, the Lake Cowal Foundation Limited (LCF) has already been delivering results consistent with its goal to protect and enhance the natural environment of Lake Cowal and its catchment area. The LCF is a non-profit Environmental Trust established in June 2000 in conjunction with the development consent process for the construction of BarrickÆs Cowal Gold Mine. Its primary goal is to protect and enhance Lake Cowal, a nationally significant ephemeral wetland located 350 km west of Sydney, New South Wales, Australia. Significant concentrations of water birds visit the lake and the Australian Heritage Commission listed Lake Cowal on the Register of the National Estate in 1992. The LCF is managed by a Board of Directors from representative member organisations including the Total Environment Centre, National Parks Association, Nature Conservation Council and Barrick Australia Limited. Although largely funded by Barrick, the Foundation also attracts external funding and works in partnership with a diverse range of other groups and organisations, beyond the mine fence. The total value of currently approved projects is estimated to be in excess of $7.1 million, which includes æin-kindÆ contributions made by the local community and in particular the Lachlan Catchment Management Authority (LCMA) and local farmers. To date, LCF has been involved with the development and implementation of 30 projects with a total of 34 project partners. LCF has worked with over 60 landholders to improve Lake Cowal and its catchment, with 6180 ha of land now being managed for conservation or sustainable farming in the local area. Many landholders have been, or are involved in property planning or participating in other training opportunities. Sustainability of LCF programs and outcomes will be assured by commitments to projects within four key themes: conservation, research and research support, sustainable farming and community education and training. The LCF works independently from the mining company and has no responsibility for the environmental management within the mining lease. It is about capitalising resources generated by the mine to enhance environmental outcomes in the wider Lake Cowal catchment area by working collaboratively with the local community, industry and government authorities to ensure the long-term protection of a unique wetland ecosystem affected by landscape scale degradation.

Jan 1, 2007