Search Documents

By J. K. Abraham

In recent years there has been interest displayed in the precipitation phenomena occurring in austenitic alloys based on the binary Fe-Ni system.1'2 Previous communications have been extended covering the kinetics of clustering in the Fe-Ni-Ti system and the effect of cluster size on subsequent mechanical properties.3'4 To a great extent the question of coherency, which has a dominant role in determining the mechanical properties, is dictated by the degree of misfit between the precipitate and matrix. Thus, the change in lattice parameter of the matrix with composition is an important variable that should be examined. The lattice parameter, ao, of austenite was determined for Fe-29.75 Ni-1 to 6 Ti and Fe-27 Ni-1 to 10 Ti alloys in this study. The alloys used in this investigation were melted in a vacuum induction furnace from a starting stock of plast iron (99.95), electrolytic nickel (99.9), and ti- tanium sheet (99.5) in a MgO crucible. The alloy compositions in atomic percent are given in Table I and their relative position in the Fe-Ni-Ti ternary is indicated in Fig. 1. The chemical analyses were taken from the homogenized bulk materials treated in a manner related earlier.3 A diamond file was used to obtain powder from the bulk. To remove the stresses induced by filing, the powders were austenitized at 1875°F for

Jan 1, 1969

By R. W. Smith, M. E. Brookes

The temperature at which th: quenched 0' (ordered bcc) phase transfo.rms to the ( (complex hexagonal) phase on heating has been examined for certain Ag-Zn and Ag-Au-Zn alloys using an electrical resistivity method. The transition temperature decreases by approxinzately 7°C as the zinc content is reduced by 1 at. pct. The critical temperature, Tc, for long-range order has also been measured for a number of Ag-Au-Zn alloys. Extrapolation to zero gold content suggests that Tc decreases by approximately 5°C per 1 at. pct reduction in zinc content. The 0 phase of the Ag-Zn system exists over a narrow range near the composition Ag zn,' Fig. 1, and has a bcc structure which is disordered above 272°C. Slow cooling to temperatures below the range 274"/258"C allows the complex hexagonal phase, r° to form.2 This is the stable structure at room temperature.3 Upon quenching 0 -phase alloys from high temperatures, it is found that the 0 — (' transformation is suppressed; but ordering takes place (i.e., 0 -0'). This ordered structure can also be obtained by the room-temperature aging of cold-worked (0.4 Deformation of the 0' phase gives rise to a fur- ther hexagonal phase ( (of nearly ideal axial ratio) which reverts to b' within a few hours.= In view of this, it has been suggested that the equilibrium struc-

Jan 1, 1969

By H. R. Gardner

THE wide variation in tension and compression properties' which exist between the a,ß and ? phases of plutonium indicate that a study of the impact properties would give a greater insight into the variables affecting the mechanical properties and formability of plutonium. In tension the a phase is quite brittle with elongations less than 1 pct. The ß phase at normal test speeds is unusually ductile; elongations up to 621 pct have been obtained. However, the ß phase is quite sensitive to strain rate; elongations decrease rapidly as strain rate is increased. The y and 6 phases are less ductile than the ß phase, with the 5 phase the more ductile of the two. Neither are very sensitive to strain rate. Considering the brittle nature of a Pu in tension and compression and the strain rate sensitivity of ß -phase Pu, both unnotched Charpy specimens and standard V-notched Charpy specimens were fabricated for testing. In addition, since iron in amounts greater than 500 ppm forms a Pu-PlgFe eutectic network which inhibits microcracking in as-cast plutonium,' it was decided to prepare impact specimens with low and high iron contents. Chemical analysis and density data for the impact specimens are presented in Table I. A total of 55 impact specimens, 32 unnotched and 23 with the standard Charpy V-notch were tested at temperatures from —45' to 330°C. The test results for both unnotched and notched specimens are illustrated in Fig. 1.

Jan 1, 1962

By Severn P. Brown

Search for ore continued at a feverish pace-as can be attested to by anyone who has tried to arrange for extensive diamond drilling. The stakes are high, and so is the cost as was indicated by Selco Exploration Ltd. when they announced discovery of base metal sulfides at Uchi Lake in northwestern Ontario. It was apparently their first commercial find after 15 years of exploration at a cost of more than $10 million. For the first time in many, many years the big exploration news has come from east of the Mississippi River. In January, the New Jersey Zinc Co., in an unusually worded press release, stated that they had made a major zinc discovery of 13-50 million tons of ore averaging 5-10% Zn. New Jersey's holdings are said to embrace 500 sq mi. The ore was discovered in eastern Tennessee in the upper part of the Knox dolomite of early Ordovician age. Reportedly the mineralization is at depths of 900 to 2000 ft. Currently about 20 diamond drills are working the area for New Jersey. At least nine other major companies are prospecting the region, which now includes parts of Kentucky. Five hundred thousand acres are said to be under lease. Greatest activity is clustered around Carthage, Tenn. In Missouri, the St. Joseph Lead Co. announced plans to develop a new mine in the Brushy Creek area of the "New Lead Belt." copper and zinc concentrates will be by-products.

Jan 1, 1970

GEORGE F. BECKER Dr. George Ferdinand Becker, notice of- whose death appeared in the May Bulletin, was born in New York City Jan. 5, 1847, the son of Alexander Christian Becker, member of a Danish family, and Sarah Cary Tuckernian Becker of Boston. Dr. Becker was the last member of the group of distinguished geologists who, in 1879, were associated with Clarence King at the time of the organization of the United States Geological Survey. He was a leader in mining geology and geophysics, and for many years had been the chief of the Division of Chemical and Physical Research in the Geological Survey, and the investigations under his direction led to the establishment of the Geophysical Laboratory of the Carnegie Institution of Washington. Dr. Becker was a graduate of Harvard University and received the degree of Doctor of Philosophy at Heidelberg, and in 1871 passed the final examinations at the Royal School of Mines in Berlin. He was for four years an instructor of mining and metallurgy in the University of California, from which he went to the United States Geological Survey. In 1896 he examined the gold and diamond mines f South Africa and at the time of the Spanish-American War was detailed to serve as geologist on the staff of General Bell with the army in the Philippine Islands. He died at his hone in Washington, D. C., on Apr. 20'.1

Jan 6, 1919

By Ben Gumpertz

THE important factors in any study of the screening of sand with a gravel enve-lope, as applied to use in oil wells, are: (r) sand size and shape, (2) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,1 from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 23 times the grain size at the ten-percentile analysis of the formation sample." This applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity.2 Also, it has been assumed by some opera-tors that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffec-tive screen. Thus the purposes of this work are: I. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screen-ing action of varying the thickness of the gravel screen.

Jan 1, 1940

By C. A. Lemke

THE ores now milled at the Midvale concentrator of the United States Smelting, Refining & Mining Co. come mostly from ;the company's mine in the Bingham district, about 18 miles west of Midvale. Custom ores from this same district and from other western mining districts are also milled at times. The Bingham ores consist of galena, pyrite, chalcopyrite, and sphalerite in a gangue of quartz, quartzite, limestone, and porphyry. The percentage of chalcopyrite is small, usually about 0.5 per cent., while the galena, pyrite, and sphalerite combined constitute about 60 per cent. of the total ore. These three minerals vary considerably' in amount and, at times, all three are somewhat oxidized. The ores also contain gold and silver, the former being mostly in the pyrite while the latter is generally with the galena. The crystallization of the economic minerals varies from fairly coarse to extremely fine. The ores are carried to Midvale by the Bingham & Garfield and the Los Angeles & Salt Lake railroads or by the Denver h Rio Grande Western railroad, in 50-ton, steel, full dump cars. The milling problem is to recover the silver-bearing galena, the gold-bearing pyrite, and the chalcopyrite in a product suitable for the lead smelter and containing the least possible amount of gangue and sphalerite and then recover the sphalerite in a product suitable for a zinc smelter. The minerals are recovered partly by water concentration and partly by water concentration combined with electrostatic treatment.

Jan 9, 1925

By Valentine R. Garflas

The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 31/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields form about 75 per cent. of the Mcxican petroleum industry. The production of the Panuco field has followed the general history of the American fields, and its gradual decline, which is at present foreshadowed, may be estimated as well as its ultimate economic life. On the other hand, the behavior of the light-oil fields to the south is unlike any in the world so far discovered, and as a result we have concentrated overproductions followed by sudden droughts, both sometimes equally unexpected. The coming in of two or three gushers within adequate pipe-line facilities will flood the market with 100,000 bbl. or more a day, while the flooding by water of a particular pool will, in a few weeks, remove from the market one-half the total production of the Mexican fields.

Jan 1, 1923

By Valentine R. Garflas

The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 31/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields form about 75 per cent. of the Mcxican petroleum industry. The production of the Panuco field has followed the general history of the American fields, and its gradual decline, which is at present foreshadowed, may be estimated as well as its ultimate economic life. On the other hand, the behavior of the light-oil fields to the south is unlike any in the world so far discovered, and as a result we have concentrated overproductions followed by sudden droughts, both sometimes equally unexpected. The coming in of two or three gushers within adequate pipe-line facilities will flood the market with 100,000 bbl. or more a day, while the flooding by water of a particular pool will, in a few weeks, remove from the market one-half the total production of the Mexican fields.

Jan 1, 1923

By V. Damiano, M. Herman

CELLULAR substructure observed in metal crystals grown from the melt. has been studied extensively'-' and is attributed to the existence of a constitutionally supercooled zone in the liquid ahead of the solidifying interface. The mathematical description of this process has been given in terms of the concentration of solute in the liquid phase, the rate of solidification, and the temperature gradien.t in the liquid as the only variables.5 This technical note presents some evidence of 1) the effect of crystal orientation on some aspects of cellular growth, and 2:) the degeneracy of these cells into dislocation arrays. The zinc single crystals used in these studies were alloyed with cadmium sufficient to produce the constitutional supercooled cellular substructure. Crystals containing 0.05 pct Cd exhibited substructure formation for a growth rate of 10 cm per hr and a temperature gradient of 15°C per cm in accord with the theory. The growing liquid-solid interface was examined after we liquid had been decanted away in a fashion similar to that described by Rutter and Chamers.' The cellular substructure was also observed after polishing and etching the surface directly behind the decanted interface with a solution of HNO, and water. Fig. 1 is a photomicrograph of a typical polished and etched surface revealing substructure, the cleavage plane, and twins. The crystal has been grown with its basal plane parallel to the direction of growth and the plane of the micrograph is per-

Jan 1, 1960

By Richard H. Terhune

The use of water-cooled breast-jackets or cinder-tap blocks is a great convenience in lead-smelting, even when siliceous slags are made. If the charges are at all basic it is almost imperative. Jackets of riveted wrought-iron or steel are expensive; those of cast-iron are liable to crack; those of bronze are costly and not durable, being easily penetrated by tapping-bars or destroyed by streams of matte impinging against them. To overcome these objections I introduced at the Hanauer works, in April, 1886, castjackets of steel, which have been in constant use since that time and are to-day as good as new. These jackets were made for us by the Chester Steel Castings Company, of Chester, Pa., at a cost of ten cents a pound at the works of that company. The metal is 5/8-inch thick, and the jackets were cored and tapped for l1/2-inch bushings, affording two large holes for the removal of dirt and incrustations. The same holes are used for feed- and discharge-water through 3/4-inch pipe. I hope the successful introduction here of cast-jackets of steel will lead to their more extended use in all branches of metallurgy where water-cooled surfaces are severely taxed, and where the size and thickness of the castings are not unfavorable to the production of a sound article, impervious to water and of high tensile strength.

Jan 1, 1889

Colorado Geological Survey, Boulder, Colo. R D George, State Geologist. The following publications of the Survey may be obtained as long as the supply lasts, at the indicated price. Bulletin 3, Geology and ore deposits of the Alma district (1910), 25 cents, 4, Geology and ore deposits of the Monarch and Tomichi districts, Chaffee and Gunnison counties (1912), can be had together with 5, pt 1, Geology of the Rabbit Ears region and pt. 2, Permian or " Permo-Carbonif erous " of the Eastern Foothills of the Rocky Mountains in Colorado, for 50 cents; 7, Bibliography of Colorado geology and mining literature (1914), 25 cents, 8, The clays of eastern Colorado (1915), 25 cents, 9, Geology and ore deposits of Bonanza district (1915), 25 cents, 10, Geology and ore deposits of Gold Brick district (1916), 25 cents, 13, Geology and ore deposits of the Platoro-Summitville district (1917), 25 cents; 14, Molybdenum deposits of Colorado (1919), 25 cents; 15, Manganese deposits of Colorado (1919), 25 cents (14 and 15 in one volume, 35 cents); 17, Twin Lakes district (1921), 25 cents. Bulletin 18, Fluorspar deposits of Colorado (1920), 25 cents, 21, The geology of the Ward region, Boulder County (1921), 50 cents, 22, Mineral deposits of the Western Slope (1921), 25 cents, 24, Some anticlines of western Colorado (1924), 50 cents; 27 (in three parts) pt 3, Geology of parts of Las Animas, Otero and

Jan 1, 1933

This excellent paper by Dr. Colombo parallels quite closely the bench and pilot work done by the Hanna Research Laboratory on the Mesabi oxidized taconites. Because of the vast reserves and future ore requirements the need to perfect the selective flocculation-flotation process becomes very necessary. The selective flocculation process is a very efficient method of desliming, leaving a fairly clean, upgraded product for flotation. However, one of the problems that we have encountered in this process was some very fine, -2 micron liberated goethite in the slimes that did not flocculate. The complete slime removal is not necessary. We remove slimes to the extent of about 5% of the iron units. However, on difficult treating ores we would remove more slimes. The reclaimed water from our pilot plant has a turbidity of about 1000-3000 ppm. We can obtain lower turbidity water but to do this would involve additional lime as a tailing flocculant and we would run the risk of flocculating the entire ground pulp in the selective flocculation process because of the increased Ca level in the water. We have about seven different geological ore types out of 17 recognizable ore types that are treatable. All of these ore types require different degrees of dispersion and grinding which is a problem. The use of acrylic acid polymers as a selective flocculant has been patented by the American Cyanamid Co. This will-have to be

Jan 1, 1979

In cooperation with the United States Bureau of Mines and the Idaho Bureau of Mines and Geology, the University of Idaho offers in the School of Mines a number of fellowships. These fellowships are open to college graduates who have had good training in mining, metallurgy, or chemistry, and who are qualified to undertake research work. The income of each fellowship is $720 a year for the 12 mo. beginning July 1, 1919. Fellows will register as students in the University of Idaho and become candidates for the degree of Master of Science in Mining or Metallurgy (unless this or an equivalent degree has been earned). Their class work-will he directed by the heads of the departments of instruction, but the greater portion of their time will be spent in research work under the direction of the Bureau of Mines staff resident at the University. The purpose f this work is to undertake the solution of definite problems confronting the mining and metallurgical industries of the State of Idaho. For 1919-20 the following subjects are being considered: 1. Flotation-with especial reference to differential separation of various minerals. 2. Availability of western wood oils for flotation purposes. 3. Treatment of the complex gold-silver ores of southern Idaho. 4. Ore-dressing problems. 5. Mining problems. Applications, with certified copy of collegiate record, statement of professional experience, and names and address of three references, should be addressed to The Dean. School of Mines. Moscow Idaho_

Jan 6, 1919

The total crude production from the Dutch East Indies, and the British Protectorates of Sarawak and Brunei for 1932 is given in the following table: Production, which had shown a rapid increase from 1921 to 1929, has since been reduced. Exploitation drilling in the majority of the larger fields was suspended and existing production kept within predetermined limits by beaning. Most of the smaller fields were shut down entirely. The depth of producing levels varies widely in the different fields. Shallow fields with drilling depths to 500 meters (1650 ft.) are still numerous as well as those with depths between 500 and 1000 m. (3300 ft.). A few of the newer fields reach greater drilling depths up to 1600 m. (5250 ft.). The deepest exploration well drilled to date (Djambi field, South Sumatra) reached a, depth of 2332 m. (7650 ft.) before abandonment in March, 1930. The specific gravities of the various crude oils produced range between 0.65 (86.2° A.P.I.) and 0.95 (17.5° A.P.I.). The lighter crudes have a high gasoline content and fuel oils are derived from the heavier crudes, which usually are rich in paraffin. Producing companies are: De Bataafsche Petroleum Maatschappij (Royal Dutch-Shell combine in Dutch territory); The Anglo-Saxon Petroleum Co. Ltd. (Royal Dutch-Shell combine in British territory); De Nederlandsch-Indische Aardolie Maatschappij (De Bataafsche Petroleum Maatschappij-Dutch East Indian Government combine); De Nederlandsche Koloniale Petroleum Maatschappij (Standard Oil Co. of

Jan 1, 1933

Another excellent Swedish underground crushing plant is that at Crusher Station 51 of LKAB in Kiruna, Sweden. Bottom-dump rail cars pass over a dump scroll to discharge magnetite ore into a 288 cu yd (220 m3) pocket equipped with a Hewitt Robins E-13 vibrating grizzly feeder. The grizzly section is 59 in. (1500 mm) long and has bar spacings 3 in. (76 mm) wide. Any oversize boulders which will not pass the chute opening to the feeder are blasted. The primary breaker is a Morgardshammar overhead eccentric 55 in. by 71 in. (1400 by 1800 mm) jaw crusher powered by a 200 hp (149 kw) motor. An open side setting of 10. 8 to 11. 8 in (275 to 300 mm) accounts for the high capacity of this crushing unit (2760 stph or 2500 mtph). This figure compares favorably with the capacity of many gyratory crushers but is typical of the Swedish jaw crushing installations, which are often followed by three more stages of crushing or by autogenous grinding. Crushed ore from the jaw crusher is combined with the grizzly under- size in the crushed ore pocket and is fed by a second vibrating grizzly feeder to the secondary cone crusher. Both crushers are serviced by 50/5 ton overhead bridge cranes. During maintenance operations air -operated gates shut off the flow of ore from the dump and primary crushed ore pockets.

Jan 1, 1978

By L. D. Hall, S. J. Rothman

DIFFUSION coefficients of RaD (PD) and RaE (Bi) in a Bi-0.255 atomic pct Pb alloy have been measured by the methods outlined in a previous paper.' The following changes were made in the experimental procedures: the bath was made up of about 400 to 500 g Bi; and no correction was made for the volume change of bismuth on melting. The data are presented in Table I and Fig. 1. A least-squares analysis of the data yielded D = (0.120 t 0.09) exp ( -9680 + 1070/RT) D- (0.0465 0.001) exp (-8100 + 466/RT). Statistical analysis of the data indicated that the activation energies are significantly different at the 50 pct level, but not at the 75 pct level, while the D values are significantly different at the 97.5 pct level, but not at the 99 pct level. The differences are thus not as clear-cut as they were for lead. However, bismuth diffuses faster than lead in high bismuth alloys as well as in lead. The high activation energies, more than twice the value calculated from viscosities, are in good agreement with the results of Grace and Derge.' No data were obtained at higher temperatures because of gas bubble formation in the capillary. Acknowledgments This work was supported by the Office of Ordinance Research under contract DA-04-200-ORD-178. The authors thank 0. P. Vieria and M. Volpe for help in the experimental work.

Jan 1, 1957

By T. R. Cass, M. R. Achter

A technique for measuring the creep and rupture strength of nickel specimens bonded by sintered oxide layers has been developed for the investigation of the role of grain-boundary oxide in the oxidation strengthening of nickel during creep at 817 °C. Prom the inverse dependence of the rate of bonding on the thickness of the starting oxide, it is suggested that the rate of diffusion of Ni++ through NiO is the controlling process at the start of sintering. Cornparisons of the creep and rupture strength and of the microstructure of sintered couples with conventionul creep specimens suggest rupture in nickel is prevented by load-bearikzg, ikltergranular layers of oxide. A number of recent investigations have shown that at high temperature and low stress the creep-rupture strength of nickel and nickel-base alloys may be much greater in air than in an inert gas or vacuum.'-7 For example, at 817°C and 2500 psi, nickep failed in vacuum in 48 hr but not in air after 4000 hr, and a Ni-Cr-A1 alloy5 at 1038°C and 3000 psi failed in vacuum in 4 hr but not in air after 731 hr. Fig. 1 is a typical creep curve in air for materials experiencing this pronounced environmental strengthening. A common feature of these curves is the entry into a third stage of accelerating creep, concurrent with the for-

Jan 1, 1962

ON FEBRUARY 13, 1953 the Miami Copper Company signed a contract with the United States Government, through the Defense Materials Procurement Agency, whereby it under- took, with a base price of 27.359 per lb (subject to escalation based on wage scales and wholesale-price indices), to exploit a new ore body in its mine in Gila County, Arizona. Recoverable ore was estimated at 23,000,000 tons, averaging about 0.677 per cent copper. Moreover, the proportion of oxidized copper, difficult to recover by flotation concentrating, was so high that an average net recovery of only ten pounds per ton (0.5 per cent) was expected. The company proposed to mine the ore by the underground method known as undercut block-caving. Unfortunately the ore body, as has been true of all Miami's ore bodies, lay so deeply buried that no possibility existed of adopting opencut mining as has been done in recent years at Miami's neighbors, Ray and Inspiration. Probably the most distinctive characteristic of Miami's operations has been the extent to which it has developed and improved methods and equipment for underground mining. True, necessity was a potent stimulant, because its available ores since 1926 have been exceptionally low-grade; so, if the enterprise were to survive, it was necessary to keep costs at the minimum. This fact does not detract, however, in any way from the remarkable achievements of Miami engineers in conducting efficient and low-cost underground mining.

Jan 1, 1957

By Norman Pilling

The deleterious effect on the mechanical properties of copper, resulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing." of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can he snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heyn1 in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder .6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 10, 1918