Search Documents

By C. C. Clark, J. S. Iwanski

The purpose of this investigation was to study mi-crostructural changes that take place in a commercial nickel-chromium-iron alloy, such as Incoloy "901," over long periods of time at temperatures up to 13 50°F and to correlate such changes with creep-rupture properties. of the alloy. In the course of the investigation, some microstructural changes were observed which correspond to microstructural alterations found in previous studies of Inconel "X." Microstructural phases have been identified in both alloys with the aid of electron and X-ray diffraction and an electron probe microanalyzer. The materials used in this investigation were from commercial heats of the following chemical composition: Pct Cr Pct Ni Pct Mo Pct Fe Pct Cb Incoloy "901" 12.51 43.67 5.72 Bal. -Inconel "X" 14.61 73.44 - 6.61 1.02 Pct A1 Pct Ti Pct Mn Pct Si Pct C Incoloy "901" 0.10 2.46 0.46 0.24 0.05 Inconel "X" 0.70 2.43 0.51 0.36 0.04 Long-term creep-rupture tests were conducted on Incoloy "901" at temperatures of 1000°, 1200°1 and 1350°F. A summary of these results is shown in Table I along with the results of a long-term creep-rupture test conducted on Inconel "X" at 1500°F. The heat treatments given the specimens are also shown in Table I. When the creep-rupture results on Incoloy "901" are compared with shorter-tertn data, there is no evidence of any undue deterioration of the creep-rupture strength with time, nor is the elongation decreased more than would be expected from the influence of time alone. INCOLOY "901" PHASE IDENTIFICATION Microscopic examination of the Incoloy "901" specimens reveals a dark etching grain boundary constituent in the specimen which was under test for about 11,500 hr at 1000°F. This grain boundary constituent was seen to increase in size as the test temperature was increased to 1200" and 1350°F, Figs. 1, 2, and 3. Simultaneously, an acicular structure of definite crystallographic orientation appears within the grains of the 1350°F specimen, Fig. 3. Under examination with the electron microscope, a fine precipitate is observed in the 1200 °F specimen. Fig. 4. It becomes considerably larger in the 2850-hr 1350°F specimen, Fig. 5. In a few areas the precipitated particles have been replaced by, or transformed to, small needles or platelets. After 7380 hr at 1350°F, Figs. 3 and 6, the needles are much larger and have replaced nearly all of the fine precipitate. X-ray diffraction studies detected the presence of hexagonal Laves phase and hexagonal n phase (Ni,Ti) in the 1350°F specimens, Table 11. Only the Laves phase was detected by X-ray diffraction in the 1200°F specimen and none was detected in the 1000°F specimen. In this latter specimen, however, the small quantity of precipitate in the grain boundaries (presumed to be Laves phase) precludes its detection by X-ray diffraction. Composition of the hexagonal Laves phase is not yet known, although its diffraction

Jan 1, 1960

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By J. L. Meijering

Oxidation hardening of cylindrical and spherical specimens first decreases with depth below the surface, but then increases again as the center is approached. This is in agreement with the view that this change in hardness is mainly determined by the change in velocity of the oxidation boundary, which affects the dispersion of the oxide. WHEN a thick slab of silver containing 0.3 pct Mg by weight is internally oxidized, the hardness measured on a cross section is found to decrease considerably with distance from the surface.&apos; This phenomenon has been attributed to the diminution of the velocity of the oxidation boundary. The smaller this velocity is, the more slowly the free-oxygen concentration rises towards the concentration in equilibrium with the oxygen gas. And a small 0 concentration favors dissociation and thus conglomeration of the oxide. For instance, the hardness decreases more rapidly during long annealings in nitrogen than in air.&apos; Measurements by Gregory and Smith3 on sections through internally oxidized Al-silver wire showed a smaller variation in hardness, probably because the wire diameter was only 0.9 mm. Wood4 found a drop in hardness with depth in internally oxidized Al-copper strip, and also—by electron microscopy—the concomitant increase in Al2O3 particle size. Under certain circumstances internal oxidation leads to formation of rather irregular inner oxide films in the midst of dispersed oxide. This special sort of conglomeration—discussed in Ref. 5—is also favored by greater depth below the surface.3,5 In this paper hardness measurements in large diameter cylindrical and spherical specimens are described. Here the oxidation velocity* goes through ness initially decreases with depth but increases again towards the center. Normally, the diffusion coefficient D1 of oxygen is very large compared to D2, that of the dissolved metal. If, furthermore, the atomic fraction c2 of the latter is much larger than the O-solubility cl- but c2D2 << c1D1- the velocities in question are easily calculated2 to be: for the cylinder and for the sphere. Here p is the radial coordinate of the oxidation boundary and R the specimen radius, which in dilute silver alloys is constant, as no external oxidation occurs. These equations have been derived for a divalent solute; for nondivalent solutes c2 has to be multiplied by half the valency. The equations are not valid near the center. For which can be considered as a standard case,2 the Eqs [I] and [2] begin to yield U-values which are appreciably too high for p/R = 0.05 and 0.15, respectively. But at the v-minima they are still very good approximations. These minima lie at p = emlR= 0.37R in the cylinder and p = 1/2 R in the sphere. Other factors besides the velocity v will also influence the hardness. The oxide concentration cox is constant in a flat strip, apart from a narrow region in the middle,2 but in cylindrical and spherical specimens cox decreases steadily with depth. When C1 << c2 and c1D1 >> c2D2 one can calculate

Jan 1, 1961

By N. J. Themelis, A. W. Last

Autogenous grinding, broadly defined as the self-comminution of ore in a cylindrical tumbling mill without using auxiliary grinding media, was first applied in the early 1930s in the so-called Hadsel mills (Hardinge, 1955) as seen in [Fig. 1], mainly used in gold mines on the US West Coast. A number of these mills were built in sizes of 6.1 to 7.3 m (20 to 24 ft) in diameter and 1.5 to 1.8 m (5 to 6 ft) in length but were later abandoned because of operating and maintenance problems. Further development of autogenous grinding led to the Hardinge wet grinding mill, the Aerofall dry grinding mill, and others. A tabulation of all known autogenous and semiautogenous installations around the world was sent recently to the authors by G. J. Kushner of Koppers Metal Processing Division. In the size range of 7.3 to 9.8 m (24 to 32 ft) in diameter, it lists a total of thirty mills used in the processing of copper ores. An additional 120 units are listed in the same size range for the processing of iron ores and other minerals. The largest mills in existence are 11.1-m-diam X 4.6-m-long (36-ft-diam X 15-ft-long) mills in Minnesota, powered by 8950 kW (12,000 hp) motors and used in taconite beneficiation. It is indicative of the phenomenal growth of this technology that none of the above 150 mills was in operation prior to 1964. Grinding rates in autogenous mills are very sensitive to variations in ore breakage characteristics and even with fairly constant ore type can exhibit large fluctuations in throughput. Autogenous grinding also depends on availability of a fraction of the ore to be ground in the form of "competent" rock which can withstand to a certain degree the tumbling and impact action within the mill. If the ore is uniformly "soft", it will soon be crushed into small size particles and further grinding, which depends on the existence of large size rocks in the mill, becomes impossible. This apparently is the case with most copper ores, as discussed by Bachman, Last and Nabbs (1970) who described pilot testing of a large number of ore samples from Kennecott &apos;s Chino Mines. Under circumstances where autogenous grinding is impractical, it is possible to realize most of its benefits by utilizing large grinding balls in place of the "competent" rock and practice what has become known in the mining industry as semiautogenous grinding. In semiautogenous grinding (SAG), a grate discharge tumbling mill is fed the product of a primary crusher or run-of-mine rock. Forged steel or alloy grinding balls, in proportions ranging from 3.10% of the total volume in the mill, are used to complement the self-grinding ability of the ore. Semiautogenous circuits can be either designed for single-stage closed-circuit grinding which produces a final product for recovery processes, or for two-stage operation in which the SAG mill product is fed to a second stage of grinding in a conventional ball mill.

Jan 1, 1981

By J. L. Foster, G. R. Gray, T. S. Chapman

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942

By G. R. Gray, T. S. Chapman, J. L. Foster

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942

By J. W. Freeman, D. N. Frey

Fundamental reasons for the improvement in creep resistance of an austenitic alloy by cold working were investigated mainly by X-ray diffraction. The creep resistance was found to be improved by the internal stresses in the lattice of the alloy induced by the cold work. THIS investigation was concerned with the fundamental reasons for improvement in creep resistance of an austenitic alloy as a result of cold working. Also, the investigation was carried out to elucidate the conditions under which cold working could be expected to improve the creep resistance. To achieve these ends, creep resistance and internal structure were correlated for a variety of cold-worked conditions. Since the aim of the investigation was not to obtain specific and extensive information on any one alloy, creep testing was done with a single stress at 1200°F. Structural studies were carried out primarily with X-ray diffraction characteristics. The alloy used, low carbon N-155, was selected on the basis of being representative of at least some of the alloys used in gas turbines. Low carbon N-155 alloy in the form of %-in. sq bar stock was used in this investigation. The chemical composition, in percent, was: C, 0.13; Mn, 1.43; Si, 0.34; Cr, 20.73; Ni, 18.92; Co, 19.65; Mo, 3.05; W, 1.98; Cb, 0.98; N, 0.14; and Fe, balance. The bar stock was produced from a 13-in. sq billet, finished to 7/s in. round cornered square between 2060" and 1910°F. Prior to use in this particular investigation, the bar stock was solution-treated 1 hr at 2200°F and water quenched. This procedure was used in order to put the stock in a condition where effects of prior processing were minimized. Experimental Procedure The specific approach to the problem was twofold. First, the influence of cold working, under various conditions, on the creep rate under a single stress at 1200°F and on the internal structure was in part determined. Second, the effect of annealing at various times and temperatures on the creep rate and internal structure of the cold-worked samples was in part evaluated. The first step was basic to the investigation—creep resistance and structure were to be correlated. The second step was taken to see if the annealed samples showed some internal changes which could also be correlated with changes in creep resistance. This it was felt would facilitate solution of the basic problem. The creep and structural studies were carried out on samples reduced approximately 5, 15, and 40 pct at room temperature and 15 pct at temperatures up to 2200 °F. Annealing of various of the samples was done at 1200°, 1400°, 1600°, and 1800°F for time periods up to 1000 hr. Studies of the annealed samples were concentrated on materials rolled approximately 5, 15, and 40 pct at room temperature and 15 pct at 1400°F. The creep tests were carried out at 1200°F under 40,000 psi, the latter being approximately the 1000 hr rupture stress of the material

Jan 1, 1952

By P. K. Koh

With identical annealing heal treatment the development of major annealed texture component seems to depend primarily upon the degree of cold reduction. Cube texture was evident on annealing- 1/2-, 1,/4- , and 1/8-mil tapes at 760°C, but it dissap-)eared on 927°C annealing of 1/8-mil tape cold reduced 96.9 pct. Some cube texturee remained as tile strongest 927 °C annealed texture component in 1/4- and 1/2-mil tapes cold reduced 93.8 and 87.5 pet, respectively. The switching coefficient increases and the squareness ratio of the hysteresis loop decreases proportionally with increasing cube pole concentration. PREVIOUS studies 1,2 on the 1/8-mil ultra-thin molybdenum permalloy tape established cold rolled and annealed textures and their magnetic performance for switch-core and coincident-current memory applications, The major cold-rolled texture was found to be of {110}<335> which is quite similar to the cold-rolled texture of silver and 70-30 cartridge brass. The major annealed texture components were found to be of {120)-- <001> and {113)<785>. Although the direction for easy magnetization for this type of alloy by the single-crystal technique is not avaliable, knowledge from related studies indicated [Ill] as the easy magnetization direction, similar to that of nickel.&apos; Therefore, a cube orientation, if present in the tape core, would be most detrimental to its magnetic performance.3 In its cold-rolled state the tape had < 111 > directions in the rolling plane 14.5 deg from the rolling direction.&apos; But the coercive force of the tape in such condition will be excessive due to large amounts of internal stresses, and therefore makes its use impossible for memory applications due to long switching time. In lower nickel alloys, suchas 50-50 nickel-iron and 65 pct Ni-Fe sheets, previous investigators4"7 found the presence of cube texture on annealing at 900° to 1000°C. Although no cube texture was found in annealed 1/8-mil tape,"&apos; its presence in some annealed 1,/4-mil tape cores was firmly established a year ago as verified by significant differences in magnetic properties. The present investigation is devoted to the orientation study and related magnetic measurements on three thicknesses of the ultra-thin tape, namely, 1/8 mil, 1/4 mil, and 1/2 mil, cold rolled directly from annealed 4-mil stock in the cold-rolled state as well as after they were annealed at 760°C (1400° F) and 927°C (1700°F). The results obtained might serve to elucidate the development of annealed texture as well as to establish clearly the importance of preferred orientation on the magnetic performance of such memory tape core despite its well-known low magnetic anisotropy exchange energy. EXPERIMENTAL PROCEDURE Samples were taken from one production heat (0.010 wt pct C, 0.004 P. 0.016 S, 0.80 Mn. 0.29 Si. 79.69 Ni. 4.42 Mo. 0.054 Co, 0.002 Ti, 0.12 Al, 0.04 Mg, 14.56 Fe). Annealed 4-mil sheets were cold re-

Jan 1, 1962

By J. R. Johanson

With the continuing development of automatic operations, it is important that reliable discharge rates through hoppers and bins be obtained for bulk solids. In most applications a feeder is used to control the feed rate. The selection of this feeder size is usually based on the rated ability of the feeder to move material without regard to the capability of the material to flow through the opening in the hopper onto the feeder. The dis charge rate through a given hopper opening may vary from zero to a theoretical maximum depending on the flow properties of the material. This paper presents an equation for the maximum discharge rate for a bulk material as a function of the hopper shape, the opening size and the flow properties of the material. Discharge-rate tests on various materials indicate good agreement with calculated values for opening sizes from a fraction of an inch to several feet. As part of a program to develop improved design criteria for bulk storage and handling facilities, a specific study of the methods involved in calculating the rate of discharge of bulk solids from hoppers and bins has been made. This study is closely related to earlier work done on the prevention of flow problems through the choice of proper design geometry of hoppers and bins1. The present paper is an extension of this earlier work, and therefore many of the concepts previously derived and explained will be used without explanation. Two types of flow will be considered: plane-strain flow in a wedge-shaped hopper and axial-symmetry flow in a conical hopper. The literature contains many studies on discharge rate for regular-shaped dry particles2*3 such as glass beads, lead shot and coarse dry sand. However, the work is empirical in nature, and it is difficult to extrapolate the given information to apply to moist, sticky materials typical of many industries. Some studies4 have shown a decrease in discharge rate with an increased moisture content of the material. However, no attempt was made to correlate the discharge rate with moisture. The method of calculating discharge rate presented in this paper was derived analytically from the basic knowledge of the flow of frictional, cohesive, granular solids, The equation includes the effect of material cohesion (stickiness), hopper configuration, opening size and bulk density of the material. THEORETICAL WORK The basic assumptions made in deriving the discharge rate equation are as follows: 1) The material is a frictional, cohesive, granular solid. 2) The flow is considered continuous and without significant density change. 3) The material at the hopper opening forms a continuously failing arch that is in dynamic equilibrium. 4) The strength of the material in the arch, which must be overcome for the arch to fail, is caused by the pressure in the flowing mass near the hopper opening. 5) This pressure at the hopper opening can be calculated5. If we consider the dynamic equilibrium of an arch of uniform thickness such as that shown in Fig. 1,

Jan 1, 1965

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the. class of Member must be at least 27 years of age and must have had at least six years&apos; employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. Senior Members: The Directors may, at the special request of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, transfer such Member or Associate to the class of Senior Member; and in special cases may waive either the requirement as to age or as to the number of years for which dues have been paid. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified -through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. .SEC. 8. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life memberships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Affiliate: Upon appropriate action by the Board of Directors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1940

By E. F. Bradley, R. I. Jaffee, H. R. Ogden, E. S. Bartlett, D. N. Williams

The mechanical properties of solid-solution-strengthened columbium alloys have been assessed as a function of alloying additions. Studies included the effects of tungsten, tantalum, molybdenum, and vanadium. Elevated temperature fabrication was required at alloying levels above about 15 pct W or 10 pct Mo. Tungsten, molybdenum, and vanadium additions increase tensile strength at room temperature and 2200°F, but tantalum additions exert little strengthening. Similarly, tungsten, molybdenum, and probably vanadium additions increase the ductile-to-brittle transition temperature, and tantalum additions decrease this parameter. The 2200°F stress-rupture strength is increased by tungsten and molybdenum additions; with 20 to 25 at. pct additions, 100-hr rupture strengths of 30,000 psi are obtainable. Small vanadium additions exhibit mild stress-rupture strengthening, and tantalum additions are innocuous. At 2500°F, tungsten additions retain stress-rutpure strengthening capability, but molybdenum additions are much less effective. Tantalum additions augment the stress-rupture strengthening of tungsten plus molybdenum additions at 2500°F. Of the refractory metals, columbium possesses specific potential for structural use in the temperature range from 2000" to about 2500°F. Desirable features of columbium are its good low-temperature ductility, ease of fabrication, oxidation mechanics (lack of a volatile oxide at moderate temperatures), good availability and reserves, and relatively low density. However, alloying is required to provide attractive strength at elevated temperatures. Published information concerning alloying be- havior of columbium relative to mechanical properties is sketchy, particularly in consideration for long-time applications at temperatures in excess of 2000°F. Only a few stress-rupture data at temperatures from 2000" to 2500°F have been reported;&apos;-&apos; these are too meager to allow rationalization of the effects of various alloying additions on creep or stress-rupture properties. Additional published data do, however, give some insight toward understanding of systematic alloying behavior for columbium relative to low-temperature strength4-&apos; and ductility,&apos; and elevated temperature tensile behavior.4,6 This paper is intended to augment previous knowledge, and to promote understanding of the alloying behavior of columbium for long-time structural service at elevated temperature. BASIC CONSIDERATIONS Solid-solution strengthening is recognized to be of prime importance in improving strength in columbium-base alloys. Other strengthening mechanisms may be (and are, in current alloys) used to augment solid-solution strengthening. As strengthening results primarily from lattice distortion, the strengthening effectiveness per atom depends upon atomic size mismatch between solvent and solute. Another factor in this regard is conformance to ideal solution behavior in the solid solution. Thus, for example, despite appreciable differences in the degree of mismatch between tungsten (5 pct), molybdenum (5 1/2 pct), and vanadium (7 1/2 pct) in solution in columbium, all are about equally effective in straining the columbium lattice at room temperature.&apos;-&apos; Similarly, tantalum additions do not strain the columbium lattice, and little strengthening is expected. Size effects being equal, maximum solution strengthening at high temperatures is anticipated to result from the addition of elements that increase the melting temperature of columbium. This expectation is based on an increase in the electronic bonding forces exhibited in the transition metal series as electronic structures approach those of the Group Vl metals. Of the metals that exhibit ex-

Jan 1, 1963

By J. Murray Riddell

The method of treating hazards wherein value is decreased, is cited by R. D. Parks. Quite properly, the theory of probabilities is made use of when multiple hazards are under consideration. E. F. Fitzhugh, Jr. $ deals with the enhancement phase graphically and uses percentage of expectancy as derived by a study of conditions and the selection of a chance factor. It is believed that both of the authors referred to fully recognize the part which human judgment plays, and as coupled with experience, training, and the application of the theory of probabilities; in that respect the composer of this paper is in accord. Within the past year, the task of arriving at a mathematical method for handling the enhancement phase, and, additionally, coupling the negative and positive phases, was explored. In citing the hazard, or negative phase, reference is made to the text by Parks. Types of Items far Consideration On the hazard, or negative, side some of the common items to be considered are: 1. Subsidence and resulting damage. 2. Flo wage of water above that anticipated. 3. Geological. (a) Decline in quality of probable ore, and/or (b) Decline in quantity of probable ore. 4. Depressed economic conditions. 5. Litigation. Similarly, on the enhancement, or positive, side common items to be considered are: 1. Flo wage of water below that estimated. 2. Geological. (a) Increase in quality of probable ore, and/or (b) Increase in quantity of probable ore. 3. Elevated economic conditions. 4. Litigation. 5. Technological advance in the art. Tn all of the above items no consideration is given to placing a value on, or giving consideration to, possibilities. For example, referring to Table 1, the estimated normal present value (Vp) of a property, exclusive of risk consideration, is taken as $100,000. If subsidence affects the usefulness of the shaft, the present value of the property will decrease to $60,000, and it is judged that there is a 1 in 4 chance that the shaft will be impaired;, consequent.ly, if subsidence took place, the present value would be reduced ($100,000-$60,000) $40,000, but since the chance is 1 in 4, the allowable reduction would be only one-fourth of $40,000, or $10,000, or a discount of 10 pct (hazard factor) of the original value; the related safety factor is taken as unity minus 0.10, or 0.90. Thus, the original Vp, $100,000, multiplied by the safety factor ($100,000 X 0.90) gives $90,000, which is the adjusted present value of the property in this single instance. Additionally, there is a water hazard, which, if encountered, will reduce the present value to $85,000. The chance is 1 in 3. Following through with the same reasoning as shown above, the derived safety factor will be 0.95. To arrive at a single multiplying factor which will express the combined risks, the two safety factors are multiplied together, 0.90 X 0.95 = 0.855. That factor when multiplied by the origirial Vp will give the adjusted, and

Jan 1, 1950

By G. R. Gray, T. S. Chapman, J. L. Foster

THE wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as tragacanth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. INTRODUCTION It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.1-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-11 The wall-building properties of fresh-water muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods generally used in controlling filtration of fresh-water muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. LABORATORY INVESTIGATIONS Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester&apos; at a pressure of 10o lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 c.c. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1941

By Bernt Ellingsaeter, Terkel Rosenqvist

IN the silicothermic reduction of magnesia, burned dolomite is treated with high grade ferrosilicon in an evacuated steel retort at temperatures between 1150° and 1200°C. The following reaction is assumed to occur MgO + CaO + 1/2 Si (Fe) - Mg(g) +- & Ca,SiO, + Fe with the equilibrium constant on the basis of thermodynamic data for the substances involved and assuming unit activity for all solid constituents, Kubaschewski and Evans&apos; calculated the magnesium pressure as a function of temperature logp,, (mmHg) = 15.06-1.61 T- log T- 13,16O/T. Pidgeon and King," who measured the magnesium pressure by means of a flow method, found values about three times the calculated ones. This may be caused by uncertainties in the thermodynamic data, but may also be caused by the formation of other reaction products, such as Ca,SiO,, which is known to be the stable silicate in equilibrium with lime. Whatever the exact reaction may be, it is evident that as long as all other factors are maintained constant the magnesium pressure will vary with the silicon activity, viz: p,, = &,. (p,,) ", where (p,,)" is the magnesium pressure by the reduction with silicon of unit activity. In the present investigation, p,,, was therefore measured for various grades of ferrosilicon and their silicon activities were calculated. The experimental method was similar to that used by Pidgeon and King. Briquettes of burned dolomite and Fe-Si alloys were placed in a 1 in. heat resistant steel tube and were heated to 1200°C. By means of a flow of purified hydrogen, the magnesium vapor was swept into a condenser filled with steel wool. From the amounts of hydrogen used and magnesium condensed the magnesium partial pressure was calculated. First a tube of 28 pct Cr steel, and later a tube of Kanthal D (a ferrous alloy with 22.6 pct Cr, 2 pct Co, and 4.5 pct Al), was used as a heat resistant tube. The latter tube showed the best heat resistance. The dolomite used had the following composition: 43.6 pct MgO, 55.5 pct CaO, 0.2 pct K,O + NalO, 0.2 pct Fe,O,, and 0.3 pct insoluble. The ferrosilicons were prepared from 98 pct Si of technical grade (0.7 pct Al, 0.3 pct Ca, and 1 pct Fe) by melting with various amounts of electrolytic iron of high purity. The alloys thus obtained were analyzed on their iron and silicon contents, which added up to between 99 and 100 pct. The amounts of reactants were chosen so that there would always be an excess of the oxides, and the average decrease in silicon content during the experiments would be about 1 pct. Most of the reaction occurred in the part of the reaction mixture facing the gas flow. The change in the silicon concentration in the part facing the condenser was, therefore, negligible. To facilitate the reaction, about 1 pct fluorspar was added to the briquette mixture. Fluorspar does not enter the reaction, but is known to act as a

Jan 1, 1957

• A new curriculum for combined liberal arts-engineering education has been announced by 6 middle western colleges. The plan involves three years of ;study at one of the 5 liberal arts colleges and two years and a summer of &apos;engineering work at Case; graduates receive both the A.B. and B.S. degrees. * A new kind of mining is being pioneered by a pest Virginia coal operator which enables four men to produce 800 tons of coal a day. The machine that makes this possible is a giant auger, 5 ft in diam and 100 ft long. Together with the carriage in which it is moved about, it weighs 60 tons. A mobile, but separate power plant of 1000 hp drives it. &apos; * The Sorel smelter, which will reduce Allard Lake titanium ores, will utilize five 6-electrode rectangular electric furnaces. Furnace hearth size will be about 18x50 ft, and the furnace will smelt about 300 tons of ore per day, producing 100 tons of iron and 130 tons of 70 pct Ti02 slag. The furnaces will be fed continuously by gravity from charge bins, and tap at intervals of 4 hr or more. Slag will be transferred to a high speed casting machine, using cast iron molds, then crushed for shipment to pigment producers. The iron will be treated to reduce its sulphur content to 0.03 to 0.05 pct, and then cast into small pigs or ingots for shipment to steel mills. • Flying of North Africa&apos;s first airborne mangetometer survey was completed this month, covering approximately 20,000 sq km in north central Tunisia for Gulf Exploration Co.&apos;s program there. Mapping was completed in less than 30 days. •Yore than 9000 employees of 11 electric companies are enrolled in a 6-hr program that successfully informs workers on the principles of the American economic system. The course is given by the Middle West Service Co. which claims that before and after employee opinion polls show that the course instilled a better understanding of free enterprise and consequently a favorable response to it. •According to a report issued by the American Geological Institute there will be 2865 graduates in geology, including advanced degrees from U.S. colleges in 1950. This supply of geologists compares with requirements for 1278 at the professional and subprofessional levels. The report contains a detailed statistical study of the supply and demand situation for geologists in the 1949-50 period. •The dark cloud of over-production in the bituminous coal industry has a silver lining, according to Natural Resources Notes. Closing marginal mines, mostly strip and truck mines, will result in lower average costs and higher quality of the coal still produced. The producers that will then constitute the industry will be properly equipped and adequately financed to carry forward an intensive campaign to holdd and increase the markets for bituminous coal. •A light, compact, highly reliable blasting machine which does not rely for its effectiveness on the operator&apos;s skill is being tested by the Army Engineers. Operating under all climatic conditions from -65 to 125F, the 50-cap machine consists of a springwound do generator and is waterproof.

Jan 8, 1950

By J. C. Allen, E. V. Herring

CHILE EXPLORATION CO&apos;s. oxide plant at Chuquicamata, the largest of its kind, started in 1915 with initial operations at the rate of 10,000 tons of ore per day. Anaconda Copper Mining Co. acquired the controlling interest in 1923 and in the next few years modernized the plant and mine, extending operations to a nominal capacity of 490 million lb of electrolytic copper yearly by 1942. Plant production averaging 495.7 million lb of copper per year was maintained for the eight-year period extending from 1941 to 1948 inclusive. During the World War II production reached its highest level when in 1944 the output was 531.8 million lb. The maximum production for any one month was 49.6 million lb, achieved in May 1947. E. A. Cappelen Smith, consulting metallurgist for M. Guggenheim&apos;s Sons, worked out the first process for the treatment of Chuquicamata copper oxide ore about 1913, and directed a staff of 20 young engineers operating a pilot plant at Perth Amboy, N. J., on three shifts for an entire year. The copper is extracted from the oxide ore by a hydro-metallurgical treatment described in detail by T. A. Campbell in AIME Transactions, Vol. 106, Copper Metallurgy, 1933. The Oxide Plant is divided into five main operations as follows: (1) Crushing, (2) Leaching, including dechloridizing and sulphur dioxide treatment, (3) Tailing disposal, (4) Electrolytic precipitation, (5) Smelting and melting. Crushing The present Primary Crushing Plant has been in operation 25 years, during which time 4,342,112 cars of 70 tons net capacity have passed through the dumpers. The ore as received from the mine is frequently blocky and up to 5 feet in section. It is reduced to 9-in. size by two 60-in. gyratory crushers, and transported to the east and west ore bins by 60-in. conveyors. In the secondary crushing operation the ore is first reduced to 2 to 3-in. size by five standard 7-ft cone crushers and two No. 10 gyratories. This product is then reduced to 3/8-in. size by fifty-two 48-in. vertical Symons disc crushers and is transported by belt conveyors to the loading bridges from which it is charged° into the leaching vats. Conveyor belt No. 14 which serves the eight vats in the east section of the leaching plant has transported over 125 million tons of ore, which is a record for any type of conveyor. This 60-in. belt travels at a speed of 600 fpm and carries loads up to 5500 tons per hr. Leaching The ore is leached in 14 vats, averaging 13,500 short tons net capacity each. These vats are lined with a natural mastic which adequately resists the sulphuric acid leaching solutions. The leaching process as presently conducted comprises soaking the ore with successive volumes of leaching solution and spent electrolyte and withdrawing successive volumes of enriched solution from the vat to a total of approximately 3.2 million gal. The first 1.6 million gal of this volume withdrawn is called strong solution and contains about 35 parts of copper per 1000. The balance of 1.6 million gal subsequently withdrawn is stored in a

Jan 1, 1952

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

By Kendall E. Born

Production of crude oil in Tennessee during 1940 was slightly more than 15,000 bbl., a decrease from 1939 of about 36,000 bbl. This sharp decline has been caused largely by curtailed activities in the shallow pools in Clay County, where approximately 3000 bbl. was marketed off the lease during the year as against more than 37,000 bbl. in 1939. The flashy production found in 1938 in the Celina area has been short-lived and the area is essentially abandoned. Failure to find steady production has been the major factor retarding developments in the northeastern Highland Rim area. The Mississippi lime production in Scott and Morgan Counties continued to show a steady decline. The Tennessee production by counties is shown in Table I. Table i.—Oil Production in Tennessee it1 1940 Production. Bbl. Number of County Wells Pumped 1939 1940 Scott............ 4 4,332 3.596 Morgan.......... I: 6,479 5,751 Fentress.......... 3 I,2XX 1,5xz Pickett........... 1 1.2XX Clay............. 8 37.200 3,XXX Developments There were 32 wells spudded in during 1940, four of which were drilling or only temporarily suspended on Dec. 31, 1940. Twenty-eight wells were completed during the year, four of which were commercial producers. The total footage drilled was 3I,214 ft. The more important wildcats are listed in Table 2; the distribution of 1940 oil and gas tests according to physiographic divisions is given in Table 3. Cumberland Platenu.—Thcre was one completion in the coal area of the state, a test that attempted to extend the Mississippi lime production in the Coon Hollow pool to the southeast in Morgan County. This test encountered only slight shows of oil in the producing horizons of the near-by Coon Hollow and Boone Camp pools. Some surface work was carried on by private interests during the year in Scott and Morgan Counties and two wells were spudded in early in 1941 The revival of interest in the Kentucky portion of the plateau will probably result in increased activity in this part of Tennessee during 1941. Several sizable blocks of acreage, some by major oil companies, are held in Scott, Morgan, and Cumberland Counties. Middle Tennessee.—The northeastern Highland Rim continued to be the most active area in the state with 20 completions, although this figure is about one third of the number drilled in 1939. Four oil wells, none with initial productions of more than I00 bbl., were completed in Clay, Fentress, and Pickett Counties. The producing horizons discovered in Pickett and Fentress Counties were in the "Sunny-brookJ&apos; pays of Trenton age. The Clay County producer was an old test drilled deeper in which oil was found at 671 ft. in the upper part of the Stones River group of limestones, a common pay in this area. All four wells were drilled in or close to old shallow production. Deeper testing into the Knox dolomite group in this area was not particularly encouraging, although one well in Fentress County encountered some saturation at 1860 to 1869 ft. in the upper

Jan 1, 1941

By V. F. Parry, E. O. Wagner

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine coal by entrapment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pet, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented. THIS paper presents a summary of investigations by the Coal Branch of the Bureau of Mines during 1949 on the removal of internal moisture from low-rank coals by processing them in the entrained and fluidized state. A paper on this subject, giving a summary of the early work, was presented at the 1949 AIME annual meeting1 and gave a the- oretical discussion of the time and heat required to dry various sizes of low-rank coal. The investigations on two pilot plants were presented in the foregoing paper. During 1949, three additional pilot plants were built to study phases of the drying problem and to investigate different techniques of handling fine coal in the entrained and fluidized state. The present paper gives operating data on the new units and presents detailed data on the drying of seven coals having bed moisture ranging from 62 to 24 pct. The problem of removing surface moisture from fine coal is principally one of heat exchange and dispersion of the coal particles so that heat can reach the liquid moisture to permit evaporation, and it does not involve the factors of size and time of contact to any great extent. If enough heat can reach the surface of the particles at temperatures higher than 250°F, moisture evaporates almost instantly, and the factors of time and size are of secondary importance compared with the factors of heat balance and dispersion of the coal. Therefore, it does not appear to be necessary to employ a fluidized bed when removing surface moisture, and the most efficient process would be one in which the coal particles are entrained in a hot gas stream of optimum temperature traveling at a velocity that causes the particles to disperse into a low-density phase. When low-rank coals are dried, the fluidized bed is necessary to provide control of time of contact. This is done by adjusting the superficial velocity which controls the density or dispersion of the particles. The density of beds having fluidized properties suitable for drying low-rank coals appears to range from about 5 up to about 15 lb per cu ft. When the density is below 5 lb per cu ft, which represents a low-density phase, optimum conditions for removal of surface moisture should be found, and this requires superficial velocities of about 15 fps. The problem of removing bed moisture from low-rank coals involves consideration of size of coal, temperature, mass flow, heat balance, pressure, time of contact, and method of dispersing the coal in the heating mediums. The experimental work presented here gives data on these factors. Coal sizes up to 1/2 in. x 0 were dried with hot gases having initial temperatures ranging from 1900° to 2400°F. Coal

Jan 1, 1951