Search Documents

By C. M. Shigley

The record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.' The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 to 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000- ooo-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation—the largest known magnesium plant utilizing sea water as its raw matcrial. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and 7 miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1949

By G. S. Scott, G. W. Jones

ECONOMIC waste caused by mine fires may become considerable,15 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters-such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control. necessarily must be based upon one or the other, or both, of these two principles. . The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion) ; and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. OXIDATION OF COAL Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored.6,16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By R. G. Clay, C. F. Seaman

The mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development ' of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that rime, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered. the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. Original Equipment and Installation A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots 2nd the up position would connect it to the Iine from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1943

By I. R. Kramer

[The final paper in the diffusion symposium was given by I. R. Kramer. The author called attention to the diffusion characteristics of chromium deposited on the surface of steel by treatment with chromium chloride and alloyed with the surface layer of the steel by thermal treatment. As the data cited were previously published in the paper " Chromizing of Steel," by I. R. Kramer and Robert H. Hafner (Metals Technology, October 1942, and in the Transactions, volume 154, 1943, pages 415-420), it is unnecessary to reproduce these data here. The following paragraphs are taken from the author's presentation.— Editor.] Aside from the well-known practical application of the diffusion phenomena to carburizing and calorizing, -diffusion also finds application in adding alloying elements to the surfaces of steel parts. The chromizing of steels is a process by which the surface of a low-alloy steel may be enriched with chromium to form a highly corrosion-resistant case; This chromized case differs from an electroplated coat in that it is a diffused layer integral with the base metal and has all of the properties of a high-chromium steel. Recently a method of chromizing has been developed in Germany by Daeves, Becker and Steinberg in which gaseous chromium chloride and hydrogen are passed over the steel at temperatures of 1650° to 1800°F. The chromium chloride reacts with the iron to give chromium and iron chloride. The chromium atoms are deposited on the surface and diffuse in as the iron atoms diffuse out, forming a layer rich in chromium. The principal role of hydrogen is to remove the carbon from. the surface of the steel. Of the two mechanisms, chemical reaction and diffusion, the one operating at the slower rate will determine the rate of formation of the layer. In this case, diffusion is slower and therefore any factors influencing its rate will affect the process. The rate of diffusion is influenced by the temperature and crystal structure of the parent metal. Depth-concentration studies show that the concentration falls off gradually for a considerable distance and then drops sharply at about 13 per cent chromium, the point coincident with the boundary of the gamma loop. The influence of the composition of the base metal upon diffusion is quite important. The depth of penetration of the chromium decreases as the carbon content increases and, of more importance, the chromized layer becomes brittle and is likely to spa11 if the carbon content is too high. It appears that in order to chromize successfully the carbon must be fixed by strong carbide-forming elements such as chromium or molybdenum, which decrease the diffusion of carbon. If this is not done, the carbon will diffuse from the interior faster than the chromium can diffuse inward, thus forming a carbide barrier. The corrosion resistance of the chromized layer is high, and these steels offer some unique advantages over other corrosion-resisting coating or alloys. While chromizing is not meant to replace stainless steels, it may serve in the saving of alloying elements. The chromizing process uses soft or low alloyed steels that can be easily hot or cold formed and since the chromized layer is soft and firmly adherent, chromized parts can be subjected to cold deformation without spalling or chipping and without loss of corrosion resistance.

Jan 1, 1944

By I. R. Kramer

[The final paper in the diffusion symposium was given by I. R. Kramer. The author called attention to the diffusion characteristics of chromium deposited on the surface of steel by treatment with chromium chloride and alloyed with the surface layer of the steel by thermal treatment. As the data cited were previously published in the paper " Chromizing of Steel," by I. R. Kramer and Robert H. Hafner (Metals Technology, October 1942, and in the Transactions, volume 154, 1943, pages 415-420), it is unnecessary to reproduce these data here. The following paragraphs are taken from the author's presentation.— Editor.] Aside from the well-known practical application of the diffusion phenomena to carburizing and calorizing, -diffusion also finds application in adding alloying elements to the surfaces of steel parts. The chromizing of steels is a process by which the surface of a low-alloy steel may be enriched with chromium to form a highly corrosion-resistant case; This chromized case differs from an electroplated coat in that it is a diffused layer integral with the base metal and has all of the properties of a high-chromium steel. Recently a method of chromizing has been developed in Germany by Daeves, Becker and Steinberg in which gaseous chromium chloride and hydrogen are passed over the steel at temperatures of 1650° to 1800°F. The chromium chloride reacts with the iron to give chromium and iron chloride. The chromium atoms are deposited on the surface and diffuse in as the iron atoms diffuse out, forming a layer rich in chromium. The principal role of hydrogen is to remove the carbon from. the surface of the steel. Of the two mechanisms, chemical reaction and diffusion, the one operating at the slower rate will determine the rate of formation of the layer. In this case, diffusion is slower and therefore any factors influencing its rate will affect the process. The rate of diffusion is influenced by the temperature and crystal structure of the parent metal. Depth-concentration studies show that the concentration falls off gradually for a considerable distance and then drops sharply at about 13 per cent chromium, the point coincident with the boundary of the gamma loop. The influence of the composition of the base metal upon diffusion is quite important. The depth of penetration of the chromium decreases as the carbon content increases and, of more importance, the chromized layer becomes brittle and is likely to spa11 if the carbon content is too high. It appears that in order to chromize successfully the carbon must be fixed by strong carbide-forming elements such as chromium or molybdenum, which decrease the diffusion of carbon. If this is not done, the carbon will diffuse from the interior faster than the chromium can diffuse inward, thus forming a carbide barrier. The corrosion resistance of the chromized layer is high, and these steels offer some unique advantages over other corrosion-resisting coating or alloys. While chromizing is not meant to replace stainless steels, it may serve in the saving of alloying elements. The chromizing process uses soft or low alloyed steels that can be easily hot or cold formed and since the chromized layer is soft and firmly adherent, chromized parts can be subjected to cold deformation without spalling or chipping and without loss of corrosion resistance.

Jan 1, 1944

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.)

Jan 1, 1951

By H. H. Kellogg

0. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.)

Jan 1, 1951

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

R. E. Powers (Mellon Institute of Industrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

R. E. Powers (Mellon Institute of lndustrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more ,or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

By N. F. Schulz

The purpose of this investigation was to evaluate the effects of variables in equipment and procedure on tube test results. This information was then to be used to formulate specifications, preferably within the practical ranges of existing machines, for test procedures capable of yielding precise and meaningful data concerning the magnetic separation of any magnetite ore, regardless of its origin. A survey of current practice was conducted among laboratories using the Davis tube test. Many tube tests were performed to experimentally evaluate the variables most likely to affect test results. A simple method was then sought for adequately interpreting tube test results. The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Fig. 1). To conduct a tube test, a sample of suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the non-magnetic and weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination. MAGNETIC SEPARATION BY THE DAVIS TUBE Mechanical separation of a specified mineral component from an ore usually requires comminution to fine sizes for sufficient liberation. Some distinguish- ing property of the mineral is then exploited to sort the desired mineral particles from the gangue particles. The magnetic separation of iron ores is based on the fact that magnetite, Fe3O4, is strongly attracted by a magnetic field while the gangue minerals are not. Maghemite, ?-Fe2O3, which may occur in certain chemically processed ores, responds similarly to magnetite. The magnetic process is practical only when the loss of iron in the form of relatively nonmagnetic hematite, Fe2O3, goethite, Fe2O3.nH2O, or other iron mineral can be tolerated. In the Davis magnetic tube concentrator, magnetic attraction holds magnetically susceptible particles in a magnetic field. Forces due to gravity, inertia, and fluid-solid friction tend to remove the less susceptible particles from the field. The probability that a given middling particle will be rejected from the tube in a given period of time is an inverse function of its magnetite content, with some modification due to particle size and mineral specific gravities. The net result is that ore particles tend to be rejected in their order of increasing magnetite content, while the retained portion or magnetic concentrate increases in grade continuously during the process. MAGNETIC SEPARATION CHARACTERISTIC The magnetic separation characteristic or MSC of a magnetite ore is the correlation between concentrate

Jan 1, 1964

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the re crystallization temperature of nickel has been investigated. All additions raised the re crystallization temperature. Both the rate of change of re crystallization temperature with at. pet solute and the limit of initial linearity are found to correlate with the free atom ground state outer electron configuration of the solute element. A comparison of all of the correlations for the transition elements studied has yielded a set of empirical relations, which allows the prediction of the effect of dilute binary transition elements on the recrystallization temperature of other transition elements. The work of Abrahamson, et al.1-7 on dilute binary solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and re-crystallization temperature. Further, it has been shown3,4 that the limit of initial linearity may also be correlated with the solute electron configuration. Since previous studies have dealt with bee and hexagonal base elements, this study is made to note what effect, if any, the fee base structure might have. Nickel also serves to give a solvent configuration which will allow the comparison of all of the transition element solvents. Olsen8 has studied the effect of some trace elements upon the recrystallization of nickel. He included only Ti, Zr, W, Mn, and Co of the transition elements. The differences in change of recrystallization temperature were attributed to the solute atom size and to the solubility of the solute in nickel. PROCEDURE All alloys were made using 99.9 + pet Ni with 0.003 C, 0.015 Fe, 0.007 0, and 0.0007 H. The solute elements were 99.9 + pet pure. According to the published binary phase diagrams9 and metallo-graphic examinations at X750, all solute elements were in solid solution. The alloys were arc melted and remelted four times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot forged at 800oC to 0.750 in. diam, machined to 0.60 in., vacuum annealed for 1 hr at 700°c, swaged to 0.40 in. and annealed at 700oC for 1 hr in vacuum. The grain size was checked and found to be 77 * 20 grains per sq mm. The specimens were then swaged to 0.187 in., yielding 76 ± 1 pet cold work. All alloys were then chemically analyzed for the solute addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The swaged rod was cut into 8.25 in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was maintained at 250" to 850°C over an eight inch length, recorded by twelve thermocouples. Control was ± 3oC, accomplished at the hot end. The recrystallization was determined metallo-graphically over the entire specimen. The criterion chosen was that point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be generally ± 3oC.

Jan 1, 1962

By Edna A. Dancy, Ronald L. Pastorek, Gerhard J. Derge

In an earlier study1 in this laboratory, it was found that there is a minimum in the specific conductance of Ni-S melts in the region of the stoichiometric composition, Ni3S2. This and similar observations on other sulfide1 and telluride2 systems suggest that short-range order exists in the molten phase for several hundred degrees above the melting point, and a qualitative energy-band model has been proposed, with intrinsic semiconduction at the stoichiometric composition and degenerate electron and hole conduction at metal- and tellurium-rich compositions. This suggestion has been substantiated for the telluride systems by Seebeck coefficient measurements which showed a change in sign from negative on the metal-rich side to positive on the tellurium-rich side. In the present investigation, in order to substantiate still further the proposed model, Seebeck coefficient determinations have been extended to the Ni-S system over a composition range in the vicinity of Ni3S2. The experimental method was essentially the same as that used for the telluride systems, with minor modifications on cells for high sulfur melts to permit the use of tungsten wires and W— W-Re th~rmocouples instead of the chrome1 or alumel wires and chromel-alumel thermocouples originally used. Chrome1 and alumel both deteriorate very rapidly in atmospheres containing sulfur. The Ni-S alloys were prepared as described in the conductivity paper. Initially, a portion of the solidified melt was analyzed at the end of a run, but after this was found to be inaccurate because of segregation during cooling, the whole sample was analyzed. The nickel content, only, was determined, the sulfur content being obtained by difference. The results are summarized graphically in Fig. 1, and clearly show a change in the sign of the Seebeck coefficient in the region of the stoichiometric composition. This change of sign near Ni3S2, coupled with the minimum in the conductivity, is suggestive of an intrinsic semiconductor at the stoichiometric composition, with degenerate electron and hole conduction on either side of this composition, in keeping with the proposed model. The negative temperature coefficient of conductivity, normally indicative of metallic conduction, is not inconsistent with this model. In the completely degenerate region it would be expected, while in the vicinity of Ni3S2 the suggestion originally made by Argyriades, Derge, and pound3 for the Fe-S system can probably be applied. They proposed that the forbidden gap between the valence band and the conduction band is small, and that the increase in the number of the conducting species with increase in temperature is not large enough to compensate for the loss of mobility through thermal scattering. The research was sponsored by the Office of Naval Research under Contract NONR-760(22) Project NR 039-081. 'E. A. Dancy and G. J. Derge: Trans. Met. Soc. Aime, 1963, vol. 227, pp. 1034-38. 'E. A. Dancy: Trans. Vet. soc. AIME. 1964, vol. 233, pp. 270-77. 'D. Argyriades, G. Derge, and G. M. Pound: Trans. Met. Soc. . 1959, vol. 215, pp. 909-12.

Jan 1, 1965

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting), but a few mimeographed copies of this provisional report are at the A.I.M.E. headquarters and will be mailed on request. . Dr. W. P. HAYNES presented some notes prepared by Dr. F. H. LAHEE, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Committee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training.. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. SHERWIN F. KELLY pointed out that much time in university training, which ought to be devoted to technical subjects, was taken up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. THOM protested against the crowding of high-school material into already overcrowded college curricula. C. E. DOBBIN, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat, toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1941

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.) O F. A. Forward, C. S. Samis, and V. Kudryk: Trans. Canadian Institute of Mining and Metallurgy. (1948) 151 (Bull. 434) 350-355.

Jan 1, 1951

By L. H. Sjodahl, J. B. Conway

of each particle on grain boundary movement is proportional to the area it occupies on the grain boundary and this increases with the square of the particle radius. In contrast to the impression gained by Tiwari the effectiveness of a particle, as a grain boundary obstacle, increases rapidly as the particle size increases. The counterbalancing factor in a dispersion of constant volume (e.g., those considered by Zener) is of course the rapidly diminishing number of particles, a situation which does not exist in thoria dispersed materials where the volume fraction of thoria remains constant. Although it has been assumed that the Zener approach is valid for the sake of the above argument, it is open to the following objections: 1) It assumes that the effect of many small particles along a grain boundary is cumulative and does not take into account the possibility of each small particle being overcome separately. In this case the boundary will not be able to move forward until the largest particle on the boundary has been overcome. This means that the rate controlling factor will be the rate at which a few relatively large particles are overcome with the remaining small particles playing a negligible role. 2) When the dispersion consists of very small particles the interparticle spacing is usually small compared to the grain size and most particles are located away from grain boundaries where they can play no part. The most efficient dispersion, from a purely geometrical viewpoint, is one where the particle spacing is equal to the grain size so that all the particles are on grain boundaries. Tiwari's second point that voids cannot prevent re-crystallization seems to be unfounded as several workes20-23 have shown that voids alone can retard grain boundary movement and recrystallization. To further convince Tiwari, Fig. 17 shows a void in deformed TD Nichrome holding back a recrystallization interface. Tiwari's explanation for the effect of voids on recrystallization, i.e., they reduce local strain energy and hence lower the driving force for recrystallization may be valid in itself but is irrelevant to the present case where even complete recrystallization after ONE of the more recently proposed expressions for describing stress-strain behavior is that due to Voce.1,2 This equation is usually written: s =s8 ?(s8?so)e??/?c [l] where s is the true stress, ? is true strain, cC is a constant called the characteristic strain, s8 is the asymptotic stress approached at high strain values, and so is the threshold stress at which the plastic deformation begins. While this expression has not been universally accepted as yet it does contain certain features which are consistent with experimental stress-strain behavior. In a more recent publication Hsu, Davies, and Royles3 employed the concept of generalized strain proposed by seth4 and identified a method for linearizing the stress-strain plot. In this approach the generalized strain was given by: where 7 is the generalized strain, 1 is the instantaneous length, 1, the datum length, and n is a constant called the "coefficient of strain measure". A value of n was said to exist which would yield the linearity: s —s+ S[.-(tf] [3] In recent studies of both these approaches, it has been found that while the Voce equation and the gen-

Jan 1, 1970

By J. Buchwald, R. W. Heckel

THE DeHoff method' of analysis of ellipsoids of constant shape provides a quantitative metallo-graphic technique whereby the actual size distribution of the ellipsoids may be determined from polished and etched random planar sections. This method provides a useful metallographic tool since it appears to be the only method available for determining the size distribution of nonequiaxed second-phase particles. This method, however, assumes that the type of particle being studied is known to be either oblate or prolate of a fixed minor to major axis ratio, q. This, in general, means that one assumes either oblate or prolate ellipsoids of a given q and checks the total volume and surface area of the second phase as determined from the particle size distribution to values of these quantities determined by other techniques. Suitable check methods may be point counting, lineal fraction, and areal fraction methods for obtaining the total volume and the Smith and Guttman2 method of intercepts for obtaining the total surface area. If the initial guess at particle shape and q were incorrect, i.c., the volume and surface information obtained from the particle size distribution data does not agree with those values obtained by other techniques, another assumption must be made and the particle size dist distribution must be recalculated. A current study in this laboratory has involved a large number of these calculations. To facilitate the handling of the calculations, the DeHoff method was programmed in the FORTRAN language for an IBM 1620 computer. The purpose of this note is to briefly describe this program. The complete program along with a list of variable names, a sample input, and a sample output may be obtained from the senior author. Basically, the program provides for the calculation of particle size distributions for a series of q values for both oblate and prolate ellipsoids for each set of input data. The total volume of second-phase particles per unit volume are calculated for each calculated particle size distribution. The output of the program is arranged to allow a rapid comparison of the calculated volume and surface values to data obtained by independent check measurements. A condensed flow chart of the program in the notation of DeHoff1 is given in Fig. 1 The calculation of the number of particles per unit volume in the jth size class, Ni, according to the DeHoff method' is: where k(q) is the shape-correction factor given by DeHoff as a function of q for both oblate and prolate ellipsoids, A is the size-class increment, k is the number of size classes, ni is the number of particles in the ith class on the planar measurement surface, and B(j,i) are the saltykov3 coefficients which correct for measurement surfaces which do not pass through the major and minor axes of the particles. The values of /3(j,i) are included as a two-dimensional array in the program. Particular values of k(q) are included in the program in increments of q of 0.05. The first calculation is carried out for q = 1 (spheres), the second for q = 0.95 oblate, the third for q = 0.95 prolate, and so forth. The number of q values chosen for the calculation is determined by a control card in the input for each set of data.

Jan 1, 1965

W. H. Blauvelt, New York, N. Y.—One thought lias been running through my mind during the wholc of this meeting and that is that the scientific and the practical men must recognize very clearly their interdependence. The value of scientific classification of coal is going to be of the very greatest importance to the users, the practical men. Is not the scientific investigation and the great amount of work that is being done in a measure at least lost to the world? Therefore the scientific investigations and the practical needs of the users should bo brought as close together, and the work should be done as closely together, as possible; that is, the scientific man should know what the practical man needs, and the practical man should not feel that the scientific man is merely a theorist. Scientific investigation is going to have a great effeet and be of great valuc to the practical man who is trying to solve his problems. In the subject which I discussed' for instance, we must look to the scientific man to tell us why coal cokes in one way and not In another and why certain coals will do certain things and others, which appear on the surfacc to be generally similar, do not act in the same way. Need or Physical Data on Coal H. J. Rose, Pittsburgh, Pa.—There is a subject which is a sort of hobby of mine; that is, the need for what might be called critical tables of constants for coal. The chemist has big volumes giving constants, such as the density, solubility, specific heat, thermal conductivity and all other physical and chemical data that have been determined for chemical compounds. Data arc also available on many common materials, for example, the density, hardness, modulus of rupture or maximum crushing strength of swamp white oak as compared with some other wood. In fact, physical data for practically cvery hype of wood commercially produced in the world can he found. In the same way the metallurgical man has handbooks giving the properties of alloys, etc., but we havc very little tabulated information about coal. Our principal reference works are the volumes published by the U. S. Bureau of Mines on the proximatc and ultimate analysis and calorific values of coals of the United States. That is 3 pioncer work of enormous value, but we have reached the point where we need more diversified information. Mr. Fulweiler raised the question of the relative strength of the different coals and cokes. Dr. Campbell and Dr. Ashley wanted to have some information on the resistance of coal to air slacking. It was brought out in the discussion that we want to know something about the coking properties of coal. There are any number of physical tests that we need, such as the thermal conductivity of certain coals, the coefficient of expansion, or the coefficient of friction; or other constants. A smattering of such information is scattered through the literature; for instance, a research worker in Wales will report a coefficient of expansion on Wclsh coals and one in South Africa will report something else for one or two kinds of African coals, hut it is difficult to find the information that is needed on our own coals. Would it not be worth while to consider collecting reliable critical

Jan 1, 1930

By Howland Bancroft

AMERICAN investment in foreign mining interests today faces its greatest task. U. S. dollars must make possible the. steady procurement of the minerals our defense effort consumes in huge quantities. The two most vital factors involved in foreign procurement are time and the continued good will of the nations from which minerals are purchased. The Point IV program was formulated to care for the second item, but it has failed to do the job. Its lack of success has not been from intent or from basic failure in formula. Foreign Investment, Four Eras Foreign mineral development, in so far as participation by private capital from the United States is concerned, may be divided into four main chronological categories: First: The period prior to the first World War when people, capital and products moved with relative freedom across international boundaries, and London was the recognized mining seat of the world. By the end of 1919 the United States direct investments abroad amounted to $3.9 billion of which some $900 million were in mining and smelting and $600 million in petroleum. Investment climate throughout most of the world was excellent. Second: The period between the end of World War I, when the international economy had been shaken from its foundations, and the beginning of the great depression of the 1930's, which still further disrupted the world economy. By that time the world mining center had moved across the sea and the United States direct investments abroad had increased to $7.7 billion of which mining and smelting accounted for $1.2 billion and petroleum for $1.1 billion. Investment climate was good in most parts of the world. Third: The period of the depression of the 1930's and the beginning of World War II during which foreign trade was still further disorganized and the international economy collapsed. Nazi barter agreements were initiated in many parts of the world, and Soviet propaganda commenced to make its, influence felt in many countries. During this period United States direct investments abroad decreased to $7.3 billion. Mining and smelting investments during the same period decreased some $200 million, though direct investments in foreign petroleum areas increased an equal amount. Investment climate became less and less hospitable in all parts of the world affected by economic nationalism. Fourth: The period since the beginning of World War II during which total direct investments abroad increased from $7.3 to $13.7 billion. Of this sum, at the beginning of 1950 investment in foreign mining and smelting is reported to have been $1.2 billion-back to where it was in 1929, and in petroleum to have reached $3.7 billion. Investment climate remained favorable in the countries respecting contractual obligations and fair in their treatment of invested capital. [ ] As noted above, the relative freedom of passage across international boundaries by people, capital and products ended with World War I and the situation remains unchanged in a greater part of the world. While this same war upset international economy, the depression of the 1930's caused the collapse of world trade, and exports from all countries fell to an alarmingly low figure. Some countries almost ceased to export. Chile, for example, reported a drop of 88 pct in exports. Countries with

Jan 1, 1952

This volume summarizes characteristics and the geological setting of porphyry copper deposits of the Western Hemisphere. Grouped by characteristics, porphyry copper deposits are described in six regions: Andean orogen, Appalachian orogen, Alaska, northern Cordilleran orogen, southern Cordilleran orogen, and the Caribbean. Each region has its own peculiarities of geologic setting, and those deposit characteristics that may be projected from one chapter to another will be used in reaching the conclusions from which to draw genetic models for porphyry copper deposits. The term porphyry in this volume denotes a type of ore deposit, rather than a rock classification. The classification of intrusive igneous rocks used in this volume is shown in Figs. 36a and 42 (pp. 103, 130). Some modern classifications suggest mineral-ratio definitions other than those used in this volume; however, most literature references cited are based on the classification shown in Figs. 36a and 42. The reader should be aware, therefore, that quartz monzonite in this volume contains from 35% to 65% potassuim feldspar and at least 10% quartz. A term used in this volume is defined where introduced within the context of a specific chapter. Distensional tectonic conditions are used in the sense of Cady (1972) in the Appalachian orogen, for example. Porphyry copper deposits are defined as large bodies of mineralized rock, usually including a porphyritic intrusive phase, that have copper sulfide minerals disseminated through them. The definition has no commercial connotation and is used strictly in a noneconomic sense to encompass the spectrum of copper mineralization associated with these deposits. Terms commonly accepted in the literature are not defined. Porphyry molybdenum and porphyry copper deposits commonly are distinguished by most economic geologists. The basis for the separation is summarized in one chapter of this volume. To permit the reader to more easily peruse the bibliography for any particular region, references will be found at the end of each chapter. The bibliography is not intended to be complete, but is designed to provide adequate minimum coverage for descriptions of deposits in the chapter concerned. Each entry is properly referenced in the text of that chapter to facilitate the reader's research into any particular topic. This volume is written from the point of view of the exploration geologist whose task it is to evaluate the structural, petrographic, mineralogic, and metallogenic characteristics of a porphyry copper deposit. The goal of the evaluation is to determine if, and where, concentrations of metals may exist in an igneous- hydrothermal system that includes the most complex set of geologic factors found in any of the many types of ore deposits. The successful porphyry copper geologist is simultaneously a petrographer, geochemist, structural geologist, and mineralogist. Some porphyry copper deposits have developed in volcanic arcs underlain by a Benioff seismic zone with a trench paralleling the arc. The most convincing example of a deposit known to have developed in an environment where subduction is an active process is the 3.3 m.y. (million years) old Dry Creek occurrence in the Aleutian arc (this volume). On the other hand, the younger deposits in the Cascades appear to have formed in a volcanic arc lacking both the Benioff zone and the offshore trench. Subduction is not widely accepted as an active mechanism for the period when the younger Cascade deposits formed. Subduction has also been questioned for deposits formed at a great distance from a plate boundary (e.g., Bingham). Regardless of the pros and cons regarding subduction, most deposits are associated with regional faults. Strike-slip

Jan 1, 1978

By J. G. Richardson

The performance of laboratory water floods is compared with the flooding behavior calculated by the Buckley-Leverett techniques from steady-state relative permeability-saturation relations. Both the steady-state and unsteady-state experiments were conducted on the same sand-packed column. Relative permeabilities were calculated by the Welge technique from the unsteady-state waterflooding displacement experiments and compared with those measured by steady-state techniques. An evaluation of the various calculation procedures was made. It was demonstrated that steady-state relative permeabilities could be used to calczcJate waterflood performance. INTRODUCTION To calculate the waterflooding behavior of a given reservoir, relative permeability-saturation relations of the reservoir rock are required. These relative permeabilities are commonly measured on core samples by steady-state experiments such as the Penn State technique.' The relative permeabilities obtained in steady-state experiments are calculated from oil and gas flow rates and pressure drops measured under conditions of equilibrium distribution of oil and water in the pore spaces with slow approach to equilibrium. On the other hand, in water floods the water saturation at a given point changes rapidly with time as the flood front passes. Extensive research2 has shown that the steady-state relative permeabilities to oil and water are independent of the rate of flow and the fluid viscosities. Research has also demonstrated that the waterflooding performance of homogeneous sands uniformly contacted by water is independent of rate when capillary pressure gradients, which are important in short laboratory columns, are made negligible. However, there is little experimental data in the literature comparing relative permeabilities calculated from steady-state flow experiments with those calculated from flooding experiments. In this paper, the production data of two water floods and the relative permeabilities calculated from a series of steady-state experiments on an unconsolidated sand column are presented along with the comparisons calculated by the Buckley-Leverett and by the Welge techniques. The purpose of this study was to determine if steady-state relative permeabilities could be used to predict the waterflooding performance. This study also permitted an evaluation of the Buckley-Leverett and Welge calculation procedures and allowed an insight into the nature of microscopic displacement of oil by water. EXPERIMENTAL APPARATUS AND PROCEDURE The apparatus used in this investigation was a Lucite column 1 ft long and 11/2 in. in diameter. A drawing of the apparatus is shown in Fig. 1. Six pressure taps were evenly spaced along the top of the column to measure the oil pressures. Three pressure taps fitted with small porous disks were spaced along the side of the column to measure water pressure. Water was admitted to the inflow face of the sand through a porous disk while oil was admitted through a hole in the porous disk and distributed to the face of the sand by grooves machined in the porous disk. Retainer screens of 325-mesh stainless steel were cemented over the inlet and outlet ports and the pressure taps to prevent loss of sand. The column was packed with a clean dry sand all of which was finer than 200 mesh. Next, the sand was saturated with a solution of 150,000 ppm sodium chloride solution. The column was weighed dry and water-saturated to obtain data for the calculation of the pore volume. A 151-cp oil was then injected into

Jan 1, 1958