Search Documents

By Ralph J. Schilthuis, William Hurst

The nature of the forces that are important in producing the oil in the East Texas field and the manner in which these forces are affected by the rate of production have always been problems of outstanding interest. These questions are of great interest to the industry as a whole on account of the economic importance of the East Texas field and to the engineers in particular on account of the unique character and behavior of the field. Subsurface pressure data throughout the field have been collected systematically, so that a quite complete history of the reservoir pressures has been kept as the field has been developed and produced. Subsurface samples of the oil and gas have been taken and these have been examined to obtain data on the physical properties of the reservoir fluids under the actual conditions of temperature and pressure. All of these data have been valuable because they have afforded the basis for a careful study of the means by which the oil is produced. It is the purpose of this discussion first to point out several of the important facts revealed by the data mentioned and then to describe studies that have been made concerning the interpretation of these facts. Reservoir Pressure Data and Properties of Oil The reservoir pressure data on the East Texas field have shown conclusively that the pressures are readily affected by changes in the rate at which the field is produced. This can well be seen in Fig. 1, where the average reservoir pressures obtained from time to time are plotted with the daily production rates and the cumulative production of the field. It is noted that the average reservoir pressure has declined irregularly, depending upon the rate of production, from the estimated original value of 1625 Ib. per sq. in. to the value of 1228 lb. per sq. in. observed for Aug. 11,1934. The decline in pressure has been more rapid at the higher rates of production than at the lower rates. In contrast, the average reservoir pressure has increased, on several occasions, upon reduction of the withdrawal rate from a high value to a lower value. The reservoir pressure data have also shown that a definite gradient in pressure has existed across the field from west to east since the begin-

Jan 1, 1935

By W. M. Rust, W. D. Mounce

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimenlally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so universally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretatioils of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in. in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resist-

Jan 1, 1946

IN order that you may be expert in every phase of this art of parting, I wish to caution you upon twelve points, all necessary, so that you may know beforehand what may happen to you and what provision you must make to obtain good results. Understand that the gain derived from this art lies in carrying out the work that you wish to do accurately and with profit, which means nothing other than working with certainty and seeing that there is no loss of gold or silver [69v] or substance of anything that is valuable in itself. For, since everything lost is silver or gold, it is valuable however little. it may be, and many little things obviously make one large one; for gain increases gain, and loss, loss. Therefore, you will have as your first task to seek to have the materials that you are to use for making the aqua fortis of as perfect a nature as possible. I tell you this because the saltpeter is often weaker and of worse quality than the alum. For this reason it is necessary to make an effort to have it not only well refined and free from earthiness but also of a nature as powerful as pig [dung] saltpeter, the color of which tends strongly toward yellow. In order to work better, you also refine this again before you put it to use, as I shall tell you in its place. Likewise, see if you can get alum of the red kind that comes from the Levant or from Cartagena, for it costs less and is more powerful. Furthermore; see that you have a good number of well-formed cucurbits of properly purified glass not too large and of, equal content and size. Above all, see that they contain, no indentations, bubbles, folds, or scratches, especially, in the, body or in the bottom, because they break easily and the nature and great force of the acid pierces them by eating away, and makes a little hole. For this reason, cucurbits. are always divided into four grades; one is taken for making aqua fortis, another for drying the waters when they are laden with silver, the third for recovering the acids from the separations, and the fourth are either rejected as useless or dangerous, or are saved for recovering the whites or for some other service. Whoever wishes to practice this art well should remember to keep a large supply of cucurbits, receivers, and alembics. The third is the precaution which one must take in luting them; first, to

Jan 1, 1942

By William M. Shakespeare

Thin sheet copper in wide widths and long lengths is being made electrolytically on a commercial scale at the Raritan Copper Works, Perth Amboy, N. J. This achievement is the result of three years of intensive development preceded by almost ten years of intermittent research. While the idea of producing sheet copper by the electrolytic process is old, the literature on the subject is limited. It is evident, however, that the idea has been attractive to many investigators for years, if the issued patents in the field may be taken as an indication. These patents may be divided into three groups. In one group metal is deposited on some form of endless cathode, of which a revolving cylinder or drum is the most common. The cathode moves slowly and at such a rate that metal of the desired thickness is deposited during one pass through the electrolyte. The deposited metal is stripped off the cathode at a point above the solution level and, after washing and drying, is wound up immediately. In the next group of patents a band of thin metal is increased in thickness by being guided through an electrolytic tank in opposition to suitable anodes. The third group covers means of producing sheets of definite dimensions where flat plates or revolving cylinders are used as cathodes. With such cathodes, sheets of definite dimensions are built up to the desired thickness and then stripped off. The process as worked out at the Raritan Copper Works combines the methods of the first two groups. In the first stage a sheet weighing 1 oz. to the square foot is produced on a revolving cylinder. This sheet is increased to any desired thickness in the second stage. In the first stage (Fig. 1) a lead-covered copper drum is mounted horizontally on a lead-lined concrete tank so that it. is partly immersed in the electrolyte. The cylindrical surface of the drum immersed in the electrolyte is opposed by lead anodes spaced about 36 in. from it. The electrolyte, made up of appropriate quantities of copper and sulfuric acid, flows into and out of the tank continuously. The ebullition of gas at the surface of the anodes induces a vigorous circulation of electrolyte between the anodes and the drum surface, which is augmented by means of compressed air introduced through a pipe between the ends of the anodes under the center of the drum, not indicated on the diagram. This

Jan 1, 1934

By W. M. Rust, W. D. Mounce

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimenlally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so universally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretatioils of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in. in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resist-

Jan 1, 1946

By E. C. Harder

J. T. SINGEWALD, JR., Baltimore, Md.-I might say a word further in regard to the Miguel-Burnier district. I am sorry Mr. Harder is not here. I had hoped to be able to ask him a few questions in regard to some of the features of those deposits. This Miguel-Burnier district is the other district that I referred to that lies in the State of Minas Geraes. The interpretation that Mr. Harder gives to, these deposits is the same as that given by Harder' and Chamberlin in a previous paper, and that is that they consist of lenticular deposits of sedimentary origin in a series of rocks that also include lenses of limestone, but they seem to think that the manganese ores occur at a definite horizon and at a horizon different from the limestone. We found that the manganese ores occur at several horizons, as also do the limestone lenses, and the limestone masses are of the same shape as the manganese orebodies, so that our own feeling was that these manganese ores simply represent concentrations within the zone of oxidation formed as. a result of decomposition and replacement of this limestone. To the east of Miguel-Burnier there is a big bend in the railroad which cuts through, at right angles to the strike, this series of rocks. Here is shown very well both the local character of the limestone lenses and the local character of the manganese lenses in that, though the distance across the bend is only a couple of hundred yards, the limestone and. ,manganese lenses do not match up at all, and it also shows plainly that both occur at more than one horizon.. Consequently there is no reason why the manganese ore could not represent alterations of this limestone. The mine workings do not as yet give very definite information on this point in that they are all comparatively shallow and within what would be the zone of oxidation so that what they will grade into below that depth, we do not know. On the other hand, the character of the ore suggests that it may, represent such -a product in the zone of oxidation in that it tends to be quite earthy; whereas, if the manganese had been there originally as such it would have undergone the same metamorphism that the other rocks have undergone and one would have expected that it would have been converted into a hard manganese ore that would today stand out pretty much as do the iron ores of that same region and not have the soft, earthy texture which is a prevailing characteristic.

Jan 4, 1917

By A. J. Langhammer

Broadly speaking, it may be said that the engineer has two major responsibilities: One is to recommend the choosing of proper machinery and equipment; the other, to assist in the simplification of design, determination of method, and advise about the most suitable material to be used. The products of powder metallurgy enter broadly into both these fields. The oil-cushion, self-lubricating bearing surface on a machine part makes for better machinery and factory equipment, often proves a life-saver in curing difficulties where bearings are overloaded or inaccessible for lubrication, or on installations that with normal practice constitute a problem entailing frequent repairs. On the other hand, other parts may require low porosity approaching solidity. In the second field, powder metallurgy provides many possibilities for improved products, improved performance, solving of technical problems, saving of weight, quiet operation, higher factors of safety, greater flexibility, attractive economies, and so on. Parts We of the automotive industries are making many powdered-metal war-machine parts, both ferrous and nonferrous, including gears, external and internal; ratchets, both external and internal; levers; pillow blocks; sliding blocks; cams; gibs; hubs with external and internal splines, and similar units. Powdered metals play an important part in our war work, as they did in peacetime in the manufacturing of passenger cars and trucks. The art of powder metallurgy is not a panacea. Although on certain parts such operations as turning, boring, facing, reaming, counterboring, milling, countersinking. chamfering, broaching, hobbing, profiling. trepanning, gear cutting, grinding, etc., can be eliminated, there will always be the need for machine tools. Advantages of Powder Metallurgy Simple machining operations often are eliminated by using powdered metal, and also many other intricate operations, some of which are of the type impossible to perform on the most modern production equipment; for instance, an external spline on a flange hub, where the spline must continue to the flange face and at full depth. Another important feature is that some of the machine parts may require a self-lubricating surface at one or more points; for example, proper lubrication of a sliding splined spool, while ordinarily most digcuit, is accomplished automatically with a self-lubricating powdered-metal bearing. Frequently machine parts are made with physical, mechanical and technological advantages unobtainable from cast or forged metals of similar analysis. Thus powder metallurgy offers the designing engineer broader latitude. Similarly, the engineer may take advantage of powder metallurgy in his teamwork with other departments. Another important advantage in powder metallurgy for machine parts is the relatively short time required for tool-up.

Jan 1, 1945

By Francis B. Foley

Fundamentally, slag control in acid open-hearth steelmaking cannot be considered from any different viewpoint than can that in basic open-hearth melting. The same laws of mass action and distribution apply in both cases, so that while most, if not all, of the recent intensive study of slag-metal reactions have been carried on in basic furnaces the principles evolved are nevertheless applicable to acid open-hearth steelmaking and it is therefore not our intention to discuss the various possible chemical reactions in the slag and between slag and metal. The points we have to carry in mind, in considering acid melting practice, are the differences in the type of steels produced and the difference in the chemistry of both the steel and the slag. The acid furnace is used to produce, let us not say "quality" steel, for, after all, a "quality" steel for one purpose is not a "quality" steel for another, but steels that require acid melting practice to be of proper "quality." Steels that are required to have high physical properties in tests taken transversely from forgings are peculiarly the product of acid furnaces. In this class may be placed various ordnance materials, notably gun forgings and projectiles and large commercial forgings requiring high transverse ductility. Forgings requiring an extremely hard surface, polished and free from imperfections, are also typical acid-steel products. Of course, such forgings can be made of basic open-hearth steel, but not with the same assurance of success. At the start, the preparation of the slag in the acid and basic furnaces differs. Lime is charged in the beginning of a basic heat to form a slag, but in the acid furnace nothing is added for the special purpose of producing a slag when the heat is melted down. The result is that the acid furnace has much less volume of slag than the basic. The slag formed upon melting down is made up almost entirely of the oxides of elements contained in the metallic charge, notably oxides of iron, manganese and silicon, the amount of silica being augmented somewhat by erosion of the furnace lining. A typical acid open-hearth slag, when the bath is completely melted, will have an analysis about as follows: CaO, 3.40 per cent; SiO2, 51.9; Fe2O3, 1.25 ; FeO, 28.86; Al2o3, 1.82; MnO, 12.22. The high iron oxide content of the slag gives it a black appearance. The metal is high in carbon and some manganese and silicon will be present, depending on the amount in the original charge, the amount of

Jan 1, 1935

By Francis B. Foley

Fundamentally, slag control in acid open-hearth steelmaking cannot be considered from any different viewpoint than can that in basic open-hearth melting. The same laws of mass action and distribution apply in both cases, so that while most, if not all, of the recent intensive study of slag-metal reactions have been carried on in basic furnaces the principles evolved are nevertheless applicable to acid open-hearth steelmaking and it is therefore not our intention to discuss the various possible chemical reactions in the slag and between slag and metal. The points we have to carry in mind, in considering acid melting practice, are the differences in the type of steels produced and the difference in the chemistry of both the steel and the slag. The acid furnace is used to produce, let us not say "quality" steel, for, after all, a "quality" steel for one purpose is not a "quality" steel for another, but steels that require acid melting practice to be of proper "quality." Steels that are required to have high physical properties in tests taken transversely from forgings are peculiarly the product of acid furnaces. In this class may be placed various ordnance materials, notably gun forgings and projectiles and large commercial forgings requiring high transverse ductility. Forgings requiring an extremely hard surface, polished and free from imperfections, are also typical acid-steel products. Of course, such forgings can be made of basic open-hearth steel, but not with the same assurance of success. At the start, the preparation of the slag in the acid and basic furnaces differs. Lime is charged in the beginning of a basic heat to form a slag, but in the acid furnace nothing is added for the special purpose of producing a slag when the heat is melted down. The result is that the acid furnace has much less volume of slag than the basic. The slag formed upon melting down is made up almost entirely of the oxides of elements contained in the metallic charge, notably oxides of iron, manganese and silicon, the amount of silica being augmented somewhat by erosion of the furnace lining. A typical acid open-hearth slag, when the bath is completely melted, will have an analysis about as follows: CaO, 3.40 per cent; SiO2, 51.9; Fe2O3, 1.25 ; FeO, 28.86; Al2o3, 1.82; MnO, 12.22. The high iron oxide content of the slag gives it a black appearance. The metal is high in carbon and some manganese and silicon will be present, depending on the amount in the original charge, the amount of

Jan 1, 1935

IN general in making such powders, all kinds of gravel, tuff, washed river silt, and similar earths whose grain is fine and lean by nature are good for this operation of casting, either by themselves or in mixture because they are disposed to receive the metals well on account of a certain dryness which they possess. Many kinds are also compounded by means of art. Of these, I shall proceed to tell of all those that experience [119] has taught me to recognize as good. But first I desire that we return to speak of the natural ones because they are real earths and can always be had wherever one may be, and in the necessary quantity. They please me greatly because they are easy to reduce on account of their disposition. A loam is made from these and mixed by beating with wool-cloth cut- tings, spent wash ashes, and horse dung. This is made into cakes and dried. These are then put to bake in a furnace or in some other way and, in fact, are baked very well. Then it is pounded and sifted with a fine sieve, or it is ground in a potter's color mill, or by hand on a porphyry with water, to the fineness that the craftsman desires, or as fine as he can make it. When it has been ground it is again drained free from water and dried out with fire. Then as much magistery of salt is taken as will moisten it. It is dried and pounded again and passed through a sieve. When it has been made as desired in this way it is moistened again before use with water, urine, or vinegar just enough so that it holds together when it is squeezed in the fist. Then, when it has been brought to this point, it is moulded as you will hear. Powders are also made of crushed brick, tripoli, vine ashes, tiles, and glazed drainpipes, or burned emery, calcined tin, straw, and of burned paper and horse dung as well as of young ram's-horn ashes and many other things. The goodness of all these depends on three things; namely, on receiving the metal well, on being so fine as to be almost impalpable, and on their being made .with a magistery that renders them hard and strong when they are dry. In addition to these powders I have used another when I needed it, and it has succeeded well every time I made it. To make this. I have taken I two parts of pumice and one of iron scale and ground them on the por-

Jan 1, 1942

Discussion of the paper of K. Huessener, (Trans., vol. 53, pp. 402 to 4333, and of the papers of Linn Bradley, H. D. EGbert and W. W. Strong, pp. 303, 319. R. J. WysoR, So. Bethlehem, Pa. (communication to the Secretary*). —At our plant (Bethlehem Steel Co.), we have had several Bradshaw burners under course of construction and erection for some time, but up to the present we have not had opportunity to put them in service. I regret that I can not take part in the discussion with some actual results from these burners. Mr. Huessener properly emphasizes the importance of obtaining the highest combustion temperature practicable in boiler practice, which demands a near approach to perfect combustion conditions. The ideal burner is the one which, while meeting the various mechanical requirements, fulfills the above condition under a wide range of gas pressure. The question as to the relative value of hot raw gas and cold washed gas for boiler use is a very interesting one. I think that in the past the importance of low temperature of washed gas sometimes has been overemphasized. Mr. Huessener has pointed out that so far as temperature is concerned, no advantage accrues in washing gas below 100" F. In many plants, there is a notable operating economy in using furnace cooling water, which is appreciably warmer than the supply water. However, in a given type of washer, other conditions being constant, the lower the exit gas temperature the lower will be the dust content; this is equivalent to saying that the more washing water is used, other conditions being constant, the lower will be the dust content of the exit gas. For each type of washer there is a certain desired average temperature difference between inlet water and exit gas, concomitant with known average dust and moisture contents, and with economical operation. With the present tendency toward smaller stove checkers, it is generally agreed that gas for stove use should be cleaned to a dust content of 0.20 grain or less. The method employed and extent of gas cleaning are clearly problems for individual furnace plants. As a general proposition, wet washing is decidedly more attractive for furnaces smelting soft, fine Lake ores than for those reducing chiefly hard, lumpy ores, such as the foreign and domestic magnetites. In the former case the average moisture content of the gas is probably 35 grains per cubic foot, the dust content is relatively high and the top temperature relatively low. In our plant, the ore mixtures consist almost exclusively of hard magnetites. The average dust content of the gas leaving the dust catcher will average only about 2 grains and the moisture about 12 grains per cubic foot, corresponding to saturation at about 83" F. The temperature is fully 100" F. higher

Jan 1, 1917

By P. A. E. Armstrong

For hardening, the steel should be heated just above the critical temperature, as a properly forged steel quenched from this heat has some toughness, with maximum hardness and density. The quenching bath should be kept at approximately a constant temperature. In drawing or tempering, longer time periods at lower temperatures are better than the shorter periods at higher temperatures. A recent questionnaire brought out the following facts: The double-arc, double-taper bit and cross bit give the best service; resharpening of the drill steels most frequently was caused by wear of gage; chipping of bit was, with one exception, the second cause; breakage of shank was with one exception, the third cause; upsetting of bit, upsetting of shank, and breakage of body were the fourth cause. The direct cause of the necessity of resharpening given was poor heat treatment first, and faulty steel and severe rock conditions second. Rock-drill Steel By N. B. Hoffman Much of the drill steel produced in America is manufactured into hollow rods. After all forging has been finished the entire bar should be thoroughly annealed and heat trcated before the point is hardened and tempered, at least where the drill has heavy duty, such as working in deep holes and hard rock. A large number of tools of like character and doing work requiring similar properties are now being made of alloy steels; for instance a steel with a carbon content of 0.75 to 0.85 per cent., manganese 0.25 to 0.35, phosphorus under 0.020, sulfur under 0.030 and vanadium 0.18 to 0.23 has proved very satisfactory for chisels. A steel of this type properly manufactured will be far superior to the ordinary carbon steels, while at the same time is one whose price range should not prove prohibitive. Much of the cutting efficiency of a drill depends on proper heat treatment. This vanadium steel has a far greater safe hardening and forging range than ordinary carbon steels, making it more nearly foolproof. It will harden nicely at 1400" I?. but will also harden well and satisfactorily at 1550" F. retaining its quality of hardness and toughness in either case. Drill Steel from Hollow Ingots BY P. A. E. ARmstrong Hollow drill steel is made from a drilled billet with a sand-filled core or the drilled, pierced, or the drilled and pierced billet, not sand-filled, is rolled down over a projectile or ball much the same as in ordinary pipe manufacture. The first is the method generally used in this country; the second is used largely in Sweden. Swedish hollow drill steel has a

Jan 1, 1922

By C. Fairhurst, A. M. Starfield

As a practicing mining engineer, I face many rock mechanics' problems daily and would like to mention one or two examples to illustrate the current gap between laboratory investigations and actual field problems. I would like to endorse Dr. Obert's suggestion that more field measurements and observations should be undertaken. There is an ever-increasing body of data beginning with Hast's results in Sweden,l then measurements at Elliot Lake, Canada, and so on, including our own measurements at White Pine, which clearly indicate that the horizontal stresses underground are often at least as large as the vertical stresses. Visual obsenation of the deformation of roof and pillars (including failure due to horizontal compression) also demonstrates that the horizontal stresses are often most important. Yet almost every laboratory investigation begins with the assumption that the only stresses acting are vertical. Roof spans in layered formations. for example, are calculated on the assumption that the rock behaves as a gravity loaded beam. This is all too often unrealistic. Roof bolts are also often considered to be simply means of suspending the gravity loaded beams. As Dr. Reed has mentioned they are probably, in fact, acting to restrain a beam which is attempting to buckle due to lateral pressure. The fact that moisture can reduce the strengths of some rocks as much as 50 percent has been known for many years. In the mine me are almost always faced with wet rock, yet no one has investigated ways in which this wakening effect can be overcome. as, for example, by waterproofing the rock. C. Fairhurst, University of Minnesota I would like to mention that we have found,2 from stress-relief determinations, that appreciable (over 1000 lb per sq in.) horizontal pressures occur also at the surface in granites quarried in central Minnesota. Whilst I agree that more field measurements are desirable, it is important to point out that most university research is undertaken by graduate students who must attend classes daily. Their research is therefore restricted to the laboratory. A.M. Starfield, University of Minnesota No one denies the importance of obtaining: data from field measurements. It is equally important, however, that field measurements be guided by theory. Much time and money can be wasted by indiscriminate measurement. An example of the value of theory in interpreting measurements is given in Dr. Obert's comments on the time dependent strain observed in a salt mine. He anticipated that the stress at the wall of the opening would change with time because salt is viscoelastic rather than elastic. It can be shown from theory that if an excavation in a viscoelastic medium is unsupported, then the stress at the wall does

Jan 1, 1967

By M. G. Benz, J. F. Elliott

Otto Schaaber (Institut für Harterei-Technik, Bremen -Schönebeck, Germany)— Langenberg, Pestel, and Honeycutt gave an interesting example of the grain refining effect nonstationary magnetic fields may execute on a solidifying metal. Probably some additional comments, based on more than a decade of experience with this method of influencing crystallization, may be useful. They refer to an attempt to explain the mechanism of grain refinement by such fields, and to recent European developments which have not been mentioned in the paper. I. During studies of the temperature distribution in a metal body near the phase boundary solid/liquid, an anomaly was observed under certain special conditions: a) direction of heat transfer as horizontal as possible, b) steady state (equilibrium, i.e,, solidification resp. melting rate exactly zero). In the liquid phase, immediately adjacent to the phase boundary, the temperature was found to be constant over an appreciable distance in spite of a high value of heat transfer (40.000 to 70.000 keal/ m2h).3 Convection, which might explain this phenomenon, could not be observed. Therefore another explanation had to be sought. The assumption that a metallic melt, especially at temperatures near the point of solidification, contains some sort of atomic arrangement with a higher degree of order than the surrounding liquid, now is generally accepted. Considering the differences in energy between such an arrangement and its environs, a transport of heat even in absence of any temperature gradient is conceivable by continued formation and redissolution of regions with a higher degree of order, i.e., with lower energy level.3 At this stage, it was not necessary to postulate any special condition as to the form or size of these regions or the distance between arrangements to be newly formed and those to be redissolved. However, a simple consideration shows that an energy transfer from one region to another will only be possible without loss of energy, if the distance between will be equal to the lattice parameters, and if, secondly, crystallographic axis or planes will be parallel.4 By the way, this assumption might give a reasonable explanation of the well known orientation effect of the heat flow during solidification. Any measures to prevent columnar crystallization should act upon this ordering mechanism: a) the regions with a lower energy (higher order) should not be allowed to arrange themselves parallel to the direction of heat flow, and their growth should be disturbed; b) all conditions leading to an appreciable heat flow of uniform direction should be avoided or removed. Condition a) may be satisfied by a physical force preferably under 90 deg to the main axis of the columnar crystals (i.e., parallel to the solidification front) acting on the ordered regions; condition b) by equalizing any differences in

Jan 1, 1962

L. C. Graton, Cambridge, Mass.—The subject of chalcocite occur; rence and its geological significance has, of course, a very important commercial bearing, as shown by the recent remark of a hard-headed mining .man: "This secondary enrichment business is one thing you geologists have put up which we can hang on to, and come out right." Most enrichments of copper ores depend upon the formation Of chalcocite from leaner sulphides. Recently it has been shown that not only does there exist this secondary or derived chalcocite, * but that in certain ores the mineral is present as an initial or original constituent, which therefore we may call primary. The desirability of distinguishing between these two kinds of chalcocite is evident and has recently been emphasized. That constitutes the first problem in this connection. I believe many who are working upon secondary enrichment of mineral deposits are giving much attention to that particular question. It is now possible to distinguish primary from secondary chalcocite in many cases. In such cases, what do we know of the' conditions under which this secondary or derived chalcocite was formed? , This is the second main question in connection with the subject. It is now plain, at least in many instances, that the formation of this derived chalcocite represents a phase of oxidation if we have in mind the primary ore as the thing acted upon. The next important question—and it is most important—is: does such oxidation go on above the zone where the rocks are saturated with water—that is, above the water level—or below, or indiscriminately above and below? Many of you have, or have had, opportunities to study at first hand, day after day, occurrences that' enable valuable conclusions to be drawn upon these and other important questions concerning the formation and significance of chalcocite. It is greatly to be hoped that your testimony will be made available and undoubtedly it will go far toward clearing up some of these doubtful points. John D. Irving, New Haven, Conn.—A short time before this meeting was called, H. V. Winchell, who was unable to be present, requested me to exhibit and describe these two samples of pyrite. (Exhibiting specimens.) They consist of fragments of pyrite inclosed in two small bottles. The first bottle shows fragments of pyrite which were immersed in water carrying copper sulphate but without SO2 for a period of two years. They remained comparatively clear and bright. No chalcocite has been deposited on them. The second bottle shows fragments of

Jan 1, 1915

By E. H. Rose

THE present symposium on flotation machines provides a unique opportunity for group reappraisal of standard or habitual viewpoints. A symposium is by definition a trading post for observations that might prove complementary when put together, thus leading to useful thoughts that might not have been evident from the original observations individually. The present paper, pertaining to power consumption in flotation, is deliberately an experiment of that kind. Data were solicited from the operating superintendents of several of the major flotation plants on this continent. The information received, covering a total of 14 separate operations in seven plants, has been collated in terms of power intensity; that is, the total power input per cubic foot of cell volume. This departs somewhat from the conventional expression of power per ton of ore treated, though the latter figure is also given for the plants concerned. Because of wartime restrictions, particularly in Canada, identifying names of plants and machines are withheld. Not as a firm conclusion, but as a tender for symposium discussion, the following points are made: I. That flotation is a power operation in much the same sense as ball milling. 2. That contact time is the complement of power intensity and may be decreased as the latter is increased. 3. That a decrease in flotation power per ton of ore can result from an increase in power intensity. ANALOGY WITH GRINDING In grinding, it has become axiomatic that the more the power put into a given operation, the greater the work performance. The analogous view is now proposed that the effectiveness of any flotation operation will be related to the mechanical energy usefully applied to that operation. Under this view, each increment of properly directed input energy should give either an increase in unit tonnage or an improvement in the metallurgical separation (concentrate grade or tailing grade), until either the theoretical limit imposed by mineral constitution or surface condition is reached, or until further increments of power become uneconomic under the law of diminishing returns. Thus, as in grinding, there are two forms of output that greater power input or improved utilization of power can produce. As for the law of diminishing returns, lower unit cost of power through improved generating efficiency in the past decade has pushed the limit back. Over and above this, however, there is strong indication in the operationg data herein presented that higher power intensity results in an actual economy of over-all power consumption. Like crushing and grinding, flotation accomplishes a rupture of the forces of molecular attraction, by taking particles from the common environment and placing them in the two separate environments of

Jan 1, 1944

By W. C. Hagel

Previous inuestigators have repovted unusually low H* and Do values for self-dzf@szon in certazn bcc metals, e.g., chromium nnd y -uvanium. It has been postulated that this is nn experimental crl -tetion for the existpnce of a four -atom ring meclzanzsm, mid there could be. zmpovtant theoretrcal Implicatlons. By utilizing a precise sectioning technique with Cr51 as the tracer, self-dzffi-lsion measurements in large grains of 99.99-pct Cr were extended from 1200° fo 1600"C. A least- squares analysis of the data yields that D 0.280 exp (-73,20U/RT) cm2 sec-'. These AH* and Do unlues are not anomalous; there is little reason to believe that n vacancy mechanism is not opevatiue. Apparent differences at lower temperatures may result from preferential diffusion along short-circuititing paths and/or sample contamination. WITH continued technological effort, chromium and chromium-base alloys should ultimately become useful high-temperature structural materials. Accurate measurements of self-diffusion coefficients in the pure metal are necessary for a quantitative understanding of sintering, grain growth, creep, and other related rate processes. However, two conflicting determinations have been reported.* Using an Since careful diffusion studies normally yield Do values ranging from 0.1 to 10 cm2 sec-l, the Paxton-Gondolf results require independent experimental corroboration before an undue amount of speculation arises to explain the apparent anomaly. As discussed by Nowick6 and clearly shown by Hoffman and Turn-bull7 for self-diffusion in silver, a low AH* and Do can arise from preferential diffusion along grain boundaries or other short-circuiting paths. The most reliable data come from high-temperature measurements where volume effects predominate. Following a precise sectioning technique developed for determining silver diffusion in the intermetallic compound AgMg8 and cation diffusion in the corundum oxide Cr2O3,9 the purpose of this study was to measure true volume diffusion in high-purity, large-grain samples at higher temperatures than considered previously. Another point of interest is the frequent proposal10-12 that chromium undergoes an allotropic transformation between 1375" and 1800°C where the diffusion data might then show a discontinuity. I EXPERIMENTAL 1) Sample Preparation. The highest purity (99.997 pet) Cr currently available is produced by reduction of chromium tri-iodide. Three pounds of the resulting crystal bar were shipped in a sealed container with a complete chemical analysis from the vendor.* In conformity with the procedure used for

Jan 1, 1962

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.' At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.' They investigated the inflammability of certain magnesium alloys. Brown3-' reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.' These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952

JOHN W. BELL, *Montreal, Quebec, Canada (communication to the Secretary?). The test results in Mr. Taggart's paper will, I am sure, be recognized as a notable contribution, and of great assistance in the study of the performance of the Hardinge mill. I regret, however, being obliged to note that Mr. Taggart still retains. such confidence in the Kick-Stadler method of computing the ?relative mechanical efficiency" of crushing machines. The Rittinger-Kick graph submitted by Mr. Gates and the tests made at McGill University disclosed precisely the same fundamental defect in the Kick-Stadler theory. Consequently, I have been obliged to recalculate in terms of Rittinger surface units the results obtained in the 28 rock-crushing tests cited by Mr. Taggart, in order to find- out what the relative efficiencies really were. In order to show the large discrepancies between the Stadler and Rittinger R. M. R's, the most, efficient result disclosed by each method is represented by the number 100, and the R.. M. E.'s for the other tests have been recalculated on this basis. The results will be found in Table 1. Personally, I look forward to the time when we shall cease to talk about "relative mechanical efficiency" and merely refer to the "efficiency" of a crusher. All that is required to accomplish this is to agree on a standard method for determining the "crushing constant" of a given rock and a standard method for calculating the efficiency. The figures in the fourth column of Table 1 have been derived by assuming a constant of 2,000 for the quartzite crushed in the Yale tests. The Stadler method sometimes indicates changes in efficiency produced by, changes in operating conditions, as I pointed out in a paper describing rock-crushing tests made at McGill University. It is, however, not enough to determine that certain changes increase or decrease efficiency; surely it is equally important to determine the magnitude of these variations. By examination of Mr. Taggart's results, I have been obliged to conclude that the size of feed and amount of reduction greatly influence the Stadler R. M. E. figures, that they are positively misleading. It should be mentioned that since the majority of the tests have been made at the least efficient feed rates, and since, moreover, it is one of the evidently very important factors affecting efficiency, it is possible that different results might be obtained by a high-tonnage feed series, and that

Jan 8, 1917

By Emby Kaye

IT is the purpose of this paper to outline briefly some of the considerations that enter into the economics of so-called recycling, the generic designation of the relatively recently developed process by which a condensate† is separated from gas-distillate gas at high pressure and the residual gas returned to the reservoir. This subject necessarily embraces not only a discussion of factors that should be considered in projecting a recycling operation, such as estimating reserves, investment and operating costs, but also a comparison of condensate with other types of petroleum. The place of condensate in its relation to the total supply of crude oil is pointed out as well as certain logical methods of product disposal. The cost of drilling wells and lease maintenance is not pertinent to this discussion because income and revenue are in this paper confined to that retained by the plant or plant operator for supplying processing facilities for the gas. Before the development of recycling a great many gas-distillate gas fields in Louisiana and. Texas provided no income to their owners. When gas was sold from these reservoirs it was accompanied by irretrievable losses of condensate in the formation. The understanding of the function of retrograde condensation resulted in the introduction of a new commercial petroleum recovery process for these hitherto unexploited fields and now permits the conditioning of this type of wet gas field for the sale of dry gas therefrom without waste. SOME ECONOMIC FACTORS The study of a gas-distillate field for possible exploitation necessarily involves the critical appraisal of a number of elements, chief of which will be discussed here: (I) estimate of distillate in place, (2) estimate of distillate that can be brought to the surface, (3) available market, (4) costs. The considerations affecting the estimating of distillate reserves. in place are in the main subject to the same errors as are involved in determining dry gas reserves. Determinable data including acreage, sand thickness, reservoir pressure, reservoir temperature, porosity and connate water provide the basis for calculating the volume of gas in place. Ample allowance must be made for connate water, which may occupy from 20 to 35 per cent of the pore space of the sand. The factor of supercompressibility is to a considerable extent nullified by the reservoir temperature. It has been considered well advised to allow this factor to serve as a cushion. With the gas reserves calculated, it remains only to assay the distillate content of the gas. Those familiar with the handling of "wet" gas at high pressure readily appreciate the variables in sampling gas from

Jan 1, 1941