Search Documents

By C. E. Kemp, A. B. Dyes

Results of a field research project on the thermal recovery of oil by movement of a combustion front are presented. This field test was conducted in the South Belridge field, This The war paitern was a Southsing1e 2.5-acre five-spot pattern in the 700-ft deep Tulare sand. Results of this project indicate the technical feasibility of producing high viscosity, low-grallity crude oils by thermal means. It was demonstrated that heavy oils could be moved rapidly over considerable distances by thermal drive, and that high percentage recoveries of oil could be effected. The bulk of the oil recovery came after arrival of the burning front at a production well. However, rapid corrosion and high-temperature failure of conventional pipe and equipment both below and above surface occurred. Stainless steels gave more satisfectory performance under these conditions than did conventional steels. Oxygen was seldom observed in gas from wells ahead of the burning front, and it appears that the front was continuous throughout the life of the experiment. INTRODUCTION During late 1953 and early 1954, industry-wide attention was focused on the thermal recovery of oil by movement of a combustion front through an oil zone. Two separate Oklahoma field tests were described in publications by Kuhn and Koch, and Grant and Szasz. To obtain basic information needed for making engineering and economic appraisals of commercial recovery of heavy oil by this thermal recovery method, a new field research projecta3,4 was started May 31, 1955. Twelve oil companies contributed to this project with General Petroleum Corp. as operator. Since combustion recovery experiments* with heavy oils in other areas had been conducted in small patterns,"' an important purpose of this test was to determine whether the process could be operated in a pattern of near-commercial well spacing. The south Belridge field, located 30 miles north of Taft, Calif., was chosen because its oil sands are similar to many heavy oil sands which typically have low primary recovery and leave a large amount of oil in place. such fields are not particularly suited for common secondary recovery methods. DESCRIPTION OF TEST SITE The test interval was a Tulare sand at a depth of about 700 ft. Nine test wells were drilled, cored and completed from Oct., 1955, through Jan., 1956. The initial pattern shown on the map, Fig. 1, consisted of an injection well (II)', four producing wells (1P-4P), and four observation wells (IT-4T). An old well (81) was also recompleted for use as an observation well. The area enclosed by the original four production wells was 2.5 acres; the distance from the injection well to each production well was 233 ft. During the combustion period, Well 5P was drilled to replace Well 2P, and Well 6P was drilled to replace Well 3P. The new wells were 25 ft beyond the old production wells along a diagonal from the injection well, and resulted in an increase in pattern area to 2.75 acres. Isopachs are shown in Fig. 1. The average thickness of the oil sand in the test pattern was 30 ft. Fig. 2 presents two cross sections through the test pattern. Oil sand is represented by white and claystone by gray. The dashed lines indicate layers of conglomerate grading to claystone. The sand thickness was fairly uniform throughout the test pattern except in the 1P area. The sand body dips gently from the northwest to southeast, about 3 degrees from horizontal. The sand is unconsoli-dated, and grades from very fine material to pebbles as large as 2 in. in diameter. Table 1 presents the average initial properties of the formation. The in-place porosity of 37 per cent was estimated from the porosity of coke-consolidated cores taken after combustion. Original core analyses data were adjusted to 37 per cent, giving pore volume saturations of 60 per cent oil, 37 per cent water, and 3 per

By C. P. Miller

In order to determine the usefulness of geochemical and biogeochemical prospecting for nickel, ten localities representing several types of nickel occurrences were selected as sites from which to collect plant and soil samples. This report covers the investigations in two of the areas. After a brief geologic description of the areas, the author presents details of the experimental tests and resulting data. Conclusions drawn from the studies led to several general guides for further prospecting. In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about three years ago, approximately ten localities, representing several different types of nickel occurrences, were sampled and about 1500 samples of plant and soil were collected. This report will cover briefly the data and results for two areas, and a summary of guides for prospecting. DESCRIPTION OF AREAS SAMPLED One locality is the Red Flats nickel prospect in Curry County, Ore., about six miles southeast of Goldbeach, and the other is the Little Rocky Creek prospect in Stillwater County, southcentral Montana, just southeast of the Benbow chromite mine. The Oregon area is a lateritic-type nickel deposit formed on a nickel-rich serpentinite peridotite complex, similar to the Josephine intrusion in southwestern Oregon. The Montana area is a nickel prospect in norite, peridotite, and related rocks of the Stillwater igneous complex. The Stillwater complex is a series of layered basic and ultrabasic rocks, with a layer of norite-gabbro at the base and a series of peridotites and gabbros above. The nickel in the Oregon deposit occurs in both the peridotite and the overlying soil. A deep lateritic soil is developed locally on the peridotite and serpentinite and constitutes the ore. The average nickel content of the lateritic soil is less than 1 pct, whereas the nickel content of the weathered peridotite is about 1 to 1.5 pct. The nickel occurs as garnierite (Mg, Fe, Ni, Mn)3 (OH)4 (SiA1)2O5 in the soil and in the olivine and pyroxene in the peridotite where it probably substitutes for Fe2+ or Mg2+ in the silicate lattices. Nickel is found in three distinct ways in the Still-water rocks: 1) it is in the olivine and pyroxene minerals in norite, harzburgite, etc.; 2) it occurs as widely disseminated grains of pentlandite-pyr-rhotite, which tend to be concentrated in the lower norite band; and 3) it occurs as discrete bodies of pentlandite-pyrrhotite and chalcopyrite which are localized in the norite zone, close to the contact with the underlying rocks. The nickel content of the norite is probably less than 1 pct, and the nickel content of the pods and lenses within the norite is about 1 pct. PROSPECTING APPROACH Although the areas are different geologically, the approach in prospecting them is fundamentally the same. The procedure is twofold: 1) a rapid reconnaissance survey to outline an area of high nickel content, and 2) a more detailed survey to outline zones of possible ore grade within the area of high nickel. The possible ore at Red Flats is concentrated in the lateritic soil, whereas at Little Rocky Creek it is in the sulfide pods. Both types are surrounded by an area of relatively high nickel content. CHEMICAL ANALYSIS Chemical analyses of nickel were made by a di-methylglyoxime colorimetric test, similar to the standard test for nickel, utilizing concentrated sul-furic acid for extraction. The lower limit of detection for nickel in soil by the method used was about 10 ppm and for nickel in plants about 5 ppm. The relative deviation was about 25 pct. SOIL PROSPECTING General Statements: A summary of the approximate average parts per million of nickel in soil, as compiled from the literature and from my study, is given in Table I. Selected references are given at the end of the paper. Few of the investigators reported the type of extraction or analysis, so the data given may not be strictly comparable to mine, which were made with a sulfuric acid extraction. Any nickel concentration greater than these average values might be considered anomalous, although each area must be studied in relation to the surrounding rocks. Method of Soil Sampling: The soil samples were taken in a zone from 1 in. to 1 ft below the humus layer, and within a 15-ft radius around a station.

Jan 1, 1961

By J. C. Melrose, W. R. Foster, J. G. Savins, E. R. Parish

Many differences can be imagined between gas-oil flow in which the gas is supplied at the face of the core and gas-oil flow in which the flowing gas was originally dissolved in the oil. If capillary pressure characteristics and flow requirements control gas saturation distribution, the gas would be expected to be located at preferred sites within the porous medium as determined by pore sizes. On the other hand, during solution gas drive the gas first appears as bubbles through a nuclea-tion process. Nothing in self-nucleation theory specifies at which sites the first bubbles should be formed. In all probability they will be randomly distributed throughout the porous medium. Furthermore, it is not at all certain that even at low rates of production the gas will redistribute itself after nucleation to the channels normally occupied by gas in simple gas flow. Stewart, et at, have shown that at least for some limestone samples, oil recoveries could not be predicted for all rates of production using any one set of relative gas and oil permeabilities. An important factor in controlling recoveries during solution gas drive was the rate of bubble formation, higher rates giving higher recoveries. Stewart, et al, attributed the increase in recovery to a better distribution of the gas phase in heterogeneous limestone samples than is obtained by simple external gas drive. Differences in recovery from these causes were not reported for sandstone cores. In the experiments to be reported here, oil recovery, pressure and producing GOR history were measured during solution gas drive for a 5-ft sandstone core. The results were compared with predictions from the Muskat method for computing solution gas-drive behavior using external gas-drive relative permeability. The effects of changing the rate of production and oil viscosity were studied. At high laboratory rates of average pressure decline, two observations were made which would not have been predicted by Muskat's depletion theory: (1) oil recovery increased with increasing rate of production for a given viscosity oil, and (2) oil recovery increased with increasing oil viscosity for a given high rate of production. Both of these observations are explained as consequences of diffusion control of gas saturations superimposed on the normal gas-oil flow requirements, Fur- thermore, discontinuous gas phase flow appears to be significant during solution gas drive. The laboratory tests were performed at rates of average pressure decline many times greater than the maximum possible rate of average pressure decline in an actual oil field. It is, therefore, not possible to draw any direct conclusions regarding the effect of rate on recovery for the solution gas-drive mechanism under actual field conditions. However, at the lower laboratory rates, recoveries were nearly independent of rate and could be predicted by the Muskat method, using external gas-drive relative permeability data. These results suggest that at normal oilfield rates the effect of rate on recovery for the solution gas-drive mechanism is negligible. EXPERIMENTAL PROCEDURES The core material for the pressure depletion studies was Bandera sandstone from an outcrop in the Mid-Continent. This sandstone was selected because of its low permeability (about 10 md), which would permit the development of substantial pressure gradients in the corn at moderate flow rates. The core was 5-ft long and 2-in. in diameter. Its properties are listed in Table 1. Relative gas-to-oil permeability ratios were measured by an external gas-drive method2. The results are shown for a short 2-in. core and for the 5-ft core in Fig. 8. Oils used in the pressure depletion experiments were kerosene and a highly refined white oil (standard white oil No. 3) with gas-free viscosities of 1.8 and 25 cp, respectively. The gas was a naturally occurring methane from Gough field, Inglewood, Calif. The oil viscosities, gas solubilities and formation volume factors are plotted as functions of pressure at 75°F in Figs. 1 and 2. Methane viscosities and compressibilities were obtained from the literature"'. A core mounting was required which could withstand up to 2,500 psi internal pressure. This was obtained by first encasing the core completely in a plastic resin (Scotch Cast, manufactured by Minnesota Mining & Manufacturing Co.) The plastic covered core was then inserted into a steel pipe equipped with screw caps so that the plastic coating could be pressured from

By R. E. Reed-Hill, W. H. Hartt

High-purity magnesium single crystals, oriented with basal plane parallel to stress axis, were deformed in tension at room temperature so as to form second-order (1011)- (1012) twins. Investigation by optical and replica electron microscopy revealed that these twins can support very large internal strains approaching 1000 pct and that fracture follows as a direct consequence of these strains. At low strains the basal plane within (10i1)- (10i2) twins rotates with increasing deformation until it becomes approximately parallel to the twin boundaries. This rotation is not consistent with deformation by basal slip in the double twin, but may be rationalized in terms of nonbasal slip. Observations also indicate that basal slip in the primary (1011) twin, prior to second-order twinning, may contribute to this rotation. Deformation markings that are difficult to interpret in terms of slip on previously observed systems were noted in the twin bands. A possible means of rationalizing these markings is to relate them to grain boundary shear. The fracture associated with these twins is thought to initiate by formation of voids at the twin boundaries. These grow into microcracks, with ultimate fracture occurring by tearing of the interconnecting regions. THE significance of deformation and fracture along second-order (10i1)-(10i2) twins in polycrystalline magnesium1-' and many magnesium alloys4 was discussed in a previous paper.5 It was noted that this double twinning mode effectively controls the room-temperature deformation and fracture of magnesium single crystals, oriented with the basal plane parallel to the tensile axis. Reed-Hill and Robertson6 observed that, although these crystals may fracture at a macroscopic strain of less than 1 pct, shear strains up to 1000 pct could occur within (1011)- (10i2) twin bands. They concluded that the fracture was "ductile" and resulted from concentrating the deformation into a very small volume. The present research was undertaken to obtain a better understanding of the deformation and fracture associated with these twins. EXPERIMENTAL TECHNIQUES The experimental procedure involved straining high-purity magnesium single crystals in tension at room temperature. Specimens were oriented so that the applied stress direction was within 2 deg of the [1010] crystal axis. The specimen cross section was rectangular with faces closely parallel to (1210) and (0002). The specimen preparation and testing procedures have been described in detail elsewhere.5 Second-order (1011)- (1072) twins nucleated during straining were studied using optical and replica electron microscopy techniques. For the latter, cellulose acetate-carbon double replicas were employed. Observations were made on the (1210) crystal surface, which is the plane of shear for twins of this type. In addition to the single crystals, some investigations were carried out on longitudinal polycrystalline specimens. These were obtained from high-purity magnesium plate with a texture in which the basal planes of the grains tended to be nearly parallel to the specimen axis. All. polycrystalline specimens were annealed prior to testing in order to produce a coarse grain structure, permitting Laue back-reflection X-ray photographs to be obtained from grains of interest. EXPERIMENTAL RESULTS a) Deformation Within ( 101 l )-( 1072) Twins. Fig. 1 is an optical micrograph demonstrating the extent of the plastic deformation that can occur in (1011)-(10i2) twin bands. Notice at the lower left corner of the photograph the large displacement of the dark band (a polishing step) where it crosses the twins. The shear strain in the twin band at this position was computed to be 700 pct, using the ratio of step width to twin thickness. It was previously shown5 that (1011)- (1012) twin bands are often composed of small, separate twins aligned close to the macroscopic habit plane. Fig. 2 is an electron micrograph from near the upper end of the twin band in Fig. 1. This illustrates that the twin habit often does not coincide exactly with the macroscopic band habit, but may be inclined at a slightly smaller angle to the matrix basal plane. Figs. 3 through 6 are electron micrographs of the twin band in Fig. 2 illustrating successive steps in the development of deformation inside the band. A twin band such

Jan 1, 1969

By Horace Pops

Martensitic transformation has been studied during cooling and heating in ß-phase Cu-Zn alloys to which small additions have been made of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, and Sb. The start and finish of the martensitic reaction and the variation of transformation temperature with third-element content were determined by electrical-resistivity measurements from alloys which had either constant zinc contents or constant values of electron concentration. All of the third elements, except nickel, lowered the transformation temperature if the results were plotted along the lines of constant zinc contents in each ternary system. A significant difference in the rate of lowering of the transformation temperature per atomic percent of the third element was observed for elements which had the same nominal valence. No systematic variation of transformation temperature with the valence of the third element was observed. It is suggested that the observed increase in transformation temperature for nickel-bearing alloys is due to the transfer of electrons from the conduction band of the alloy to virtual bound states. However, electron concentration is not the most important factor controlling the instability of the 0 phase. The transformation temperatures of the ternary alloys can be predicted from the following approxilnate expression: Ms (°K) = +3280 - 80 Zn + 8 Ni - 30 Ag - 12 Au - 140 Cd -90 Ga- 145 In - 80 Ge -175 Sn - 120 Si - 150 Sb MOST binary ß -phase alloys based upon the noble metals copper, silver, and gold are unstable at low temperatures and transform spontaneously by a martensitic reaction. This transformation has been studied recently in the ordered bcc ß'-phase Cu-Zn binary al1oys1,2 where the transformation temperature is below the room temperature and decreases with an increase in zinc content. It has been reported that the transformation temperatures can be raised above room temperature by small additions of a third element such as silicon3,5 or gallium,4,5 but no quantitative study has been made. The transformation temperature of different binary alloys can be altered by third-element additions. For example, it was shown that nickel and copper may have a large effect on the Ms temperature of CU-Al6 and Au-cd7 alloys. The present investigation was made to determine systematically the influence of various third elements on the martensite-transformation temperature of Cu-Zn ß-phase alloys. Since these alloys have an electronic origin,' alloy compositions were chosen so that the transformation temperatures could be determined at constant zinc contents or at constant values of electron concentration. I) EXPERIMENTAL PROCEDURE Ten ternary alloy systems were obtained by adding nickel, the noble metals silver and gold, and some B-subgroup elements to a Cu-Zn matrix. These are arranged according to their rows and columns in the Period Table as follows: Each ternary alloy was prepared by melting and casting weighed quantities of high-purity metals (99.99+ pct) in sealed quartz tubes under a partial pressure of helium to make a 4-g ingot. The molten alloys were shaken vigorously and then quenched in water. Since the weight loss was negligible, the compositions of the ingots after casting and annealing were assumed to be the same as the nominal compositions. The ingots were homogenized after casting in helium-filled Vycor tubes for 24 hr at temperatures between 750" and 810 C and quenched into brine. Metallographic examination revealed that all alloys were homogeneous, poly crystalline ß-phase alloys, and that the grain size was in the range 1 to 5 mm. Electrical-resistivity measurements were made to determine transformation temperatures of the ternary alloys during continuous cooling or heating. Transformation temperatures of the ternary alloys can be determined by electrical-resistivity measurements since the resistance of the martensitic phase is much higher than that of the 0' phase. The technique has been described previously in connection with a study of Au-Zn alloys.9 The reproducibility of transformation temperature was approximately ±6°C. II)RESULTS A hysteresis was always observed in electrical-resistivity curves and was usually less than about 12°C.

Jan 1, 1967

By Klaus Schwerdtfeger

Activities of lead in Pt-Pb and Pd-Pb melts in the temperature range of 800° to 1200°C have been detev-mined from electromotive-. force measurements 202th the cells Both systems display strong negative deviations from Raoult's law. The data obtained with cell [1] were combined with available data on the activity of PbO in silica-satuvaterl PbO-SbO2 melts to calculate the standard free cnergy of formation 01- liquid PbO. FREE energies of formation of oxides and activities of components in metal and oxide melts can be determined with galvanic cells consisting of a metal phase, an electrolyte containing the oxide of one of the components of the metal phase, and an oxygen electrode. This technique has been used previously to measure the standard free energy of formation of solid sio2, 1 and activities in Fe-si, CO-si,2 Ni-Si,2 and CaO-P2O5 3 melts. The present paper reports activities in Pt-Pb and Pd-Pb melts as measured with the same experimental technique. EXPERIMENTAL METHOD General Considerations. The following cells were used: Pbl (PbO-SiO2)liquid, SiO2 Pt-Pb 1 (PbO-SiOz)liquid, SiO2solidO2 [2] Pd-Pb (PbO-SiOz)liquid, SiO2solid O2 [3] Liquid alloy and' oxide melt were contained together in a silica glass crucible of essentially the same design as described previously.1'2 The PbO-SiO2 melts are ionic conductors.' During the experiment, the silica glass crystalizes in a layer adjacent to the electrolyte. The electrolyte equilibrates with solid silica and hence attains the composition of the Si02-liquidus curve in the system PbO-SiO2 at any particular temperature. Molybdenum wires were used to establish contact with the liquid metal. The oxygen electrode, which reaches the surface of the PbO-SiO, electrolyte from above, consists of a platinum wire inserted into a ceramic tube and provided with a 2-mm-diam platinum bead at its end. Gas of known oxygen partial pressure (pure oxygen of 1 atm: air, or N2 with 1.04 pct 0,) is blown through the ceramic tube onto the surface of the electrolyte. The cell reaction is Pb (metal) + 1/2O2 (gas) = PbO (electrolyte) [4] No oxidation of platinum or palladium ("displacement reaction") occurs. This is to be expected from the noble character of platinum and palladium, but was also shown experimentally, as described in the next section. The galvanic electromotive force of the cell is given by where AG is the change in free energy for Reaction [4], E(=2) is the number of electrical equivalents necessary to form 1 mole of PbO, and F is the Faraday constant. Formula [5] is valid only if no junction potential exists within the electrolyte. Junction potentials occur only when the compositions of the electrolyte are markedly different at the electrodes. Such differences are negligible in the PbO-SiO, electrolyte, as shown in the next section. Since molybdenum contact leads are used, appropriate corrections were made on the measured electromotive forces to account for the thermoelectric effect of the Mo-Pt couple. The thermoelec-tromotive forces were measured separately with a Mo-Pt couple, and were found to vary linearly from 19 mv at 740°C to 40 mv at 1310°C with molybdenum being positive and platinum negative (cold junction at 25°C). Extrapolation of these values to higher temperatures yields values which are in satisfactory agreement with those obtained previously in the temperature range 1440° to 1630°c.1,2 The change in free energy for Reaction [4] is expressed as where chemical potentials of the species. The value of constant for a given temperature because the slag composition is fixed. Inserting [6] into [5] and using appropriate expressions for upb and uO2 the relation

Jan 1, 1967

By Kenric C. Owen

INTRODUCTION Situated 23 miles east of Pretoria the Premier Mine started diamond production in 1903. Two years later it produced the largest diamond yet discovered, the 3 106 carat Cullinan stone. For the period to 1932 when the mine was closed down due to economic circumstances, open cast mining was practised using inclined rope haulage traction and by this time had produced 48.5 million carats of predominantly industrial quality diamonds from 148 million tons of ore. In 1945 it was decided to re-open the mine using underground mining methods. A system using long hole benching was devised (Hodgson and Sewel 1960). This system was later modified but still forms the basis for approximately fifty percent of production. Following the successful introduction of block caving on associated diamond mines in the Kimberley area (Gallagher and Loftus 1960) this mining method was introduced to the Premier Mine in the late 60's and now accounts for nearly 50% of production. This paper will discuss block caving at Premier Mine in the light of our experience and discussion will be directed to the main geological and structural features of the orebody and host rocks and the related constraints imposed on the mining methods. Reference is made to the long hole benching mining method for comparative purposes. GENERAL DESCRIPTION OF OPERATIONS The ore from the block caving and bench mining areas gravitates via ore passes to a twin haulage, 500m below surface. Electric 13 tonne locomotives, each hauling a train of 10 Granby type cars, deliver the ore to two 42" x 48" (1.06m x 1.22m) jaw crushers. The ore is reduced in size to minus 0.15m before being hoisted to the treatment plant on surface. Hoisting is done with 12.5 tonne bottom discharge skips in a five compartment rectangular shaft using two 3 240 H.P. semi automatic Ward Leonard winders. A small single drum service winder operates in the other compartment. Men and materials travel in a separate shaft in a 5,4m x 2,8m cage operated by a Koepi winder. These two shafts are also the main intake airways to the mine. The two main extraction fans capable of 250 m3/s at 3,2 kPa are situated on surface and are connected to the underground workings by an incline and a network of air passes and return airways. GEOLOGY Although there are numerous occurrences of kimberlite bodies in the district, the Premier Mine kimberlite pipe is the only economic orebody. It is roughly oval in shape with surface dimensions of 900m on the long axis and 450monthe short axis. The surface area is 320 000 m2. The kimberlite has intruded a massive body of felsite and norite which is intersected by a number of faults. The contact between the kimberlite and host rock is clear cut and dips inward at an average angle of 80°. Cutting across the pipe and the country rock is a 75 metre thick gabbro sill, the top of which intersects the pipe below the 347m level and dips at 15' to the north west. The kimberlite has been metamorphosed a distance of some 20m both above and below the sill contacts. Age measurements on biotite from the gabbro date the sill as 1 115 million years, thereby providing a minimum age of the pipe. (Pre Cambrian). All other pipes in South Africa are of Cretaceous age (60 million years). A simplified geological plan and section of the Premier Mine orebody is shown in Figure 1. It is thought that the kimberlite intruded in at least three distinct phases. The kimberlites of these different phases can be distinguished most easily by their characteristic colour. BROWN KIMBERLITE. This is the oldest kimberlite and forms a crescent shape in plan on the south eastern side of the pipe. In depth it increases in relative area. Although the brown kimberlite carries the highest diamond grade in terms of carats per ton all the various kimberlites in the Premier pipe are economic to mine.

Jan 1, 1981

By R. F. Hehemann, D. J. Cometto, G. L. Houze

The w transformation in the Zr-Nb system was studied using X-ray diffraction, dilatometric, re-sistornetric, hardness, and metallographic techniques. w forms in a diffusionless, completely reaersible manner on quenching and in a diffusion-controlled manner- on aging. The temperature at which w begins to form on quenching was determined as a Junction of composition and was found to decrease with increasing solute content. w formed bv aging establishes a metastable equilibrium with an enriched ß phase. The ß/w + ß transus has been determined for this metastable equilibrium and employed to rationalize retrogression and reversion phenomena observed in these alloys. The decomposition mechanism is discussed in terms of a gradual or continuous transformation from ß to the w state. BETA- stabilizing alloying elements lower the MS temperature of the martensitic bcc (ß) to hcp (a') transformation in zirconium and titanium alloys. In certain titanium alloys, a lower symmetry modification of the martensitic structure, termed (a"), also has been reported.1,2 These martensitic transformations are suppressed when the amount of the ß-stabilizing element exceeds a critical level. However, the high-temperature ß phase cannot be quenched to room temperature without change. At alloy contents just above the critical level, |ß trans-forms to the w phase when cooled rapidly.3-6 The amount of w in quenched alloys is reduced by increasing alloy content, and this phase virtually disappears above a critical composition.5 In addition to the transformation during cooling, w also can be formed by aging ß at temperatures below approximately 500°C, and significant alloy enrichment of retained 13 accompanies the isothermal transformation.1-8 The structure of LC is closely related to that of the ß from which it forms.9-15 The bcc (ß) lattice can be generated using a hexagonal cell with three atoms located at (000) and ±(2/3, 1/3, 1/3). This cell has an axial ratio of 0.612 and is oriented with respect to the cubic cell such that (0001)H (111)C and [1120]H [101]C. Consequently, there are four possible orientations of the hexagonal cell, associated with the four (111) planes of the bee lattice. Formally w can be obtained from 0 by allowing the two atoms at the ±(2/3, 1/3, 1/3) positions to approach the coordinates ±(2/3, 1/3, 1/2) and there are four equally probable orientations of w for each 0 grain. In titanium alloys w retains the cubic axial ratio of 0.612" and hence also can be indexed as triply cubic, but this is not the case for aged Zr-Nb alloys where w is clearly hexagonal with an axial ratio of 0.622." The lattice parameters and atomic positions of w depend on thermal history and alloy content. The atomic positions (000), ±(2/3, 1/3, 1/2) provide reasonable agreement between calculated and observed diffracted intensities for w in the fully aged condition.10,14 In the quenched condition, on the other hand, the atoms appear to be displaced from the central plane12,13,15 and assume positions ±(2/3, 1/3, Z = 0.42-0.48) rather than ±(2/3, 1/3, 1/2). This results in a structure with trigonal rather than hexagonal symmetry. The readily detectable parameter and axial-ratio changes of w in Zr-Nb alloys make this system especially attractive for studying the structural changes that occur in the formation and aging of w. Particular attention in this investigation has been directed to the relationship between the structure of w in the quenched and aged conditions, and to certain aspects of the reaction kinetics. MATERIALS AND PROCEDURE Zr-5, 12, 17.5, and 25 pct Nb alloys were prepared by a double arc-melting practice, encased in stainless-steel cans and hot-rolled to 1/8-in.-thick sheet.* Charged weights have been employed for the niobium contents and interstitial analyses are reported in Table I. Dilatometric, X-ray diffraction (filtered CuK, and MoK, radiation), metallographic, and hardness techniques have been employed to follow the transformations during isothermal and quench-aging heat treatments. In quenched specimens, the electrical resistivity also was studied. Betatizing was conducted for 1 hr at 900°C. With the exception of the isothermal dilatometric studies, samples were

Jan 1, 1965

By C. J. Frosch, J. A. May, H. G. White, C. D. Thurmond

Gallium phosphide epitaxial layers were grown from the vapor phase on undoped single-crystal galliurn arsenide substrates in silica tubes by an open-tube wet-hydrogen process. The epitaxial layers were grown over a range of water pressures at three substrate temperatures. Excess donor concentrations were determined by surface barvier capacitance measurelrzents without removing the layers from the substrates. The excess dmlor concentration, ND-NA, is fo~ind to vary approxilnately inversely with the pressure of water added to the hydrogen carrier gas. This is the relationship that would be expected for singly ionized silicon donors on gallium sites in extrinsic galliunz phosphide, with the silicon coming from the SiO generated by the reaction of hydrogen with the silica tube. An increase in the partial pressure of water in the hydrogen stream decreases the SiO pressure. The results indicate that ni, the intrinsic hole and electrmt concentration for gallium phosphide at the three substrate temperatures, is smaller than the concentration estimated from available data for the density of states effective masses and the energy gap. Mass-spectrographic measurements confirm that the dono?, introduced into gallium phosphide is silicon. The equilibrium concentrations of silicon in vapor-flown gallium Phosphide have been estimated from available thernzodynamic information that includes the solubility measurements of silicon in gallium phosphide in equilibrium with a gallium-rich liquid phase. Satisfactory agreement with the measured silicon concentrations is obtained. FROSCH1 has described an open-tube process for growing single-crystal Gap from the vapor phase by a GazO transport mechanism. The method depends upon the reaction of H20 in an H2 carrier gas with a heated source of polycrystalline Gap which provides the necessary vapor species. When the temperature of these vapor species is lowered, super saturation occurs and single-crystal Gap will deposit on a suitable substrate. Unintentionally doped single crystals of Gap grown by the wet H2 process in silica tubes are n type. Evidence is presented to show that the donor introduced is silicon, and that a qua si-equilibrium model accounts for the inverse dependence of the donor concentration on the water partial pressure and predicts the magnitude of the donor concentrations. Ainslie et al. experimentally showed a similar inverse relationship between the carrier density and oxygen pressure for GaAs. Emission-spectrographic analyses showed a decrease in the silicon concentration with increasing oxygen overpressure for GaAs. Cochran and Foster suggested the theoretical possibility of suppressing silicon contamination by using Ga20 generated by the reaction of gallium with water vapor. 1) EXPERIMENTAL The apparatus and procedures are essentially the same as those described by Frosch.' The apparatus consists of a 25-mm-ID SiO2 tube extending through a controlled high-temperature flat zone for the location of the polycrystalline Gap source and a downstream temperature gradient falling at a rate of about 14°C per cm. The latter provides the region of super saturation for the location of the single-crystal substrate. The partial pressure of water in the inflowing hydrogen stream, pA2, O was controlled by mixing me-tered proportions of dry H2 with H2 saturated with H2O vapor at 0°C. The total gas flows were about 200 cu cm per min in all experiments. The Gap sources were prepared by pulverizing boat-grown polycrystalline ingots to pass a 20-mesh sieve. The substrates were cut from an undoped single-crystal boat-grown GaAs ingot purchased from Monsanto. This ingot had a carrier concentration of about 1015 atoms per cu cm, a resistivity of about 5 ohm-cm, and a mobility of about 5000 sq cm per v sec at 25°C. Substrates with dimensions of 1 by 1 by 5 x lo-' cm were employed. The growth faces were chemically polished (111) arsenic faces. Epitaxial layers, at least 7.5 x 10-3 cm thick, were grown,. This required from 1 to 24 hr depending upon the Pii2Q values and the temperatures. In all of the runs, the source temperatures were 50°C higher than the substrate temperatures. Samples were prepared

Jan 1, 1968

By Charles Smeal, Robert J. Schafer, Max Quantinetz

Normally metal powders cannot be ground to sub-micron sizes because of welding and agglomeration phenomena. Through the use of selected grinding aids and grinding fluids, nickel and other metal powders have been ball-milled as fine as 0.1 It was found that certain inorganic salts are more effective grinding aids for metal powders than conventionally used surfactants. METAL and alloy powders are used to produce reagents, pigments, coatings, solders, brazes, and parts for industry by powder metallurgy techniques. They are also combined with refractory compounds to produce cermets and dispersion-hardened products. One of the interests at the Lewis Research Center has been to explore the potentialities of the dispersion strengthening process. Since the work of Ir-mann, many investigators have shown that the strength of dispersion-hardened products may increase with decreasing interparticle spacing.24 One approach to achieving small interparticle spacing is to combine fine refractory compounds and metal powders, preferably below 1 in size. In attempting to obtain fine metal powders, it was found that until very recently the best that could be obtained from commercial suppliers, particularly of ductile metals, was about 1.0 . Interest was therefore developed in providing finer metal powders for dispersion-hardening studies. Information obtained from the literature, from others working in the field, and from prior experimental work performed at NASA, led to a consideration of ball-milling as a technique to produce the desired materials. Some of the variables associated with ball-milling are the size, material, and nature of construction of the grinding container; the nature and amount of the grinding material and material to be ground; and the nature and amount of the grinding liquid and grinding aid, if employed, and the grinding time. In all ball-milling, welding and agglomeration can oc- cur as well as grinding. Because of the tendency of ductile metals to weld together, they are difficult to grind.5 The ultimate particle size obtained on grinding is generally the one at which the rate of grinding becomes equal to the rate of welding. To help delay welding and thus obtain smaller particle sizes, grinding aids are often employed. The principal objective of this investigation was to produce submicron metal powders by ball-milling the powders with selected grinding aids and grinding fluids. A secondary objective has been to attempt to explain the variations observed in grinding behavior by considering possible grinding mechanisms and correlating various parameters with grinding effectiveness. Three groups of ball-milling experiments were run; one in which the grinding aid was varied, a second in which the grinding fluid was varied, and a third in which the material being ground was varied MATERIALS, APPARATUS, AND PROCEDURE In the first group of experiments in which the grinding aid was varied Inco Carbonyl Grade B nickel powder initially 2.5 (all sizes refer to average particle size as measured by Fisher Sub -sieve Sizer) was used as the material being ground and 200-proof ethyl-alcohol as the grinding fluid. Surfactants, representative of typical organic structures, were selected as grinding aids. Inorganic salts used as grinding aids were chosen on the basis of the size and valence of their ions. Water soluble salts were used in order to facilitate their removal from the slurry after grinding. In the second set of experiments, grinding of the 2.5- Ni powder was tried in four different grinding liquids; water, cyclohexane, n -heptane, and methy-lene chloride. In this study seven grinding aids selected from those tried in the first group of experiments were employed. In the third group of experiments 200-proof ethyl alcohol was again used as the grinding fluid to mill Cu, Cr, Fe, Ag, and Ni powders of various initial particle sizes' All mill charges contained 300 ml of grinding liquid and 3000 g of 1/2 in. stainless steel balls. When inorganic salts were used as the grinding aid, 70 g of salt and 210 g of metal powder were employed, and with surfactants 6 g of grinding aid and 300 g of

Jan 1, 1962

By C. B. Daellenbach, T. D. Tiemann

The prevention of quartz flotation by chelation of activating ions with the tetrasodium salt of EDTA in oleic acid flotation was investigated using a small vacuum flotation cell. It was found that flotation of quartz could be entirely suppressed in the presence of activating ions during complete flotation of hematite. It was further shown that the concentration of activating ions liberated from Wisconsin Gogebic taconite is sufficient to float quartz in an oleic acid system. Large tonnages of low grade siliceous iron ores occur on the iron ranges of the Lake Superior district. Although the lower grade nonmagnetic types are currently not of economic importance, they constitute a large future potential source of iron and steel, and hence have been the subject for extensive research on their beneficiation. TACONITES Of particular interest to the Dept. of Minerals and Metals Engineering at the University of Wisconsin have been the low grade nonmagnetic taconites of the Wisconsin Gogebic Range. These occur as five members of the iron formation and have been described in detail elsewhere.' Essentially they consist of an intimate mixture of hematite, goethite and quartz, with minor amounts of siderite, magnetite, iron containing silicates, and manganese minerals. A typical mean analysis based on the Bureau of Mines analyses' is: SiO2-52.50%, Fe2O3-43.40%, (Fe-30.38%), A12O3-1.15%, P2O5-0.07%, Mn2O3-0.29%, CaO-0.07%, (S-0.03%), Loss on ignition-2.00%. The quartz in these ores is of a microcrystalline variety,2 and so intimately associated with the iron oxide minerals that extremely fine grinding, in the order of minus 325 mesh, is required for liberation. During grinding and subsequent flotation, the concentration of quartz activating ions in the pulp becomes sufficiently high to activate quartz which floats along with the iron minerals in the presence of oleic acid. cook3 and co-workers concluded that oxidized iron ores released appreciable quantities of quartz-activating ions in water pulps. This is shown to be true in the present investigation. As a matter of fact, application of this phenomenon, as well as the intentional addition of activating calcium ions, is made use of in the an ionic flotation of silica from the iron oxide minerals.4,5 In view of the above, it becomes almost impossible to effect a sharp separation of quartz in the oleic acid flotation of the iron oxide minerals from these taconites, even with satisfactory liberation. This fact led to the current investigation to find a means of linking the activating ions with a chelating agent. The aim was to establish basic data for the quartz-water-oleic acid system which might not only be applicable to iron ores, but also to the flotation of other siliceous ores as well. EXPERIMENTAL METHODS Vacuum Flotation Cell: The vacuum flotation used in this investigation is similar to that used by previous investigators.6,7,8 The cell consisted of a 100 ml graduated cylinder with the lip removed. Vacuum from a water aspirator was applied to the cell through a trap; suitable tubing, and a rubber stopper inserted in the top of the cell. Constant absolute pressure was maintained by means of a manometer connected to the trap with a tee. Flotation: The required amount of activating ion solution was pipetted into a beaker. This was then diluted to 99.0 ml with water having a pH below that desired for the test, or so adjusted with HC1. After addition of 1.0 ml of oleic acid solution (2.0 mg oleic acid per ml), the pH was readjusted to the desired value with NaOH, and the entire solution transferred to the cell containing 1.5 gm of quartz. After vigorously agitating the cell and its contents for 2 min, the vacuum was applied to the cell and the estimated degree of flotation observed for a 3-min period. Activating ions studied included Ca++, Mg++, Al+++, and Fe+ + + added as chloride solutions. In addition,

Jan 1, 1964

By W. B. Morrison

The principal factors influencing the total percent elongation of a lead-tin eutectic and several low-alloy steels which exhibit superplasticity were investigated. These factors are: a) Strain-rate sensitivity of the stress (m). b) Specimen geometry; in particular, diameter-to-length ratio (d0/l0), and surface irregularity (e.g. notches). A feature of the tensile deformation of a superplastic alloy is the early appearance of a neck which continues to extend throughout the test. As a result the total elongation is directly related to the diameter-to-gage-length ratio. The strain-rate sensitivity of the stress varies during extension, mainly because of microstruc-tural changes. A satisfactory correlation exists between the minimum strain-rate sensitivity and total elongation, as indicated in the equation shown below. Notches cause a considerable reduction in total elongation and their effect is greatest at high values of strain-rate sensitivity. An initial notch depth exists below which there is no appreciable effect on elongation. An equation relating elongation to strain-rate sensitivity and specimen geometry is proposed, THE total percent elongation of a tensile specimen is usually regarded as a measure of superplasticity. However, little attention has been given to the fact that total elongation is also a function of specimen diameter and gage length, even though the importance of geometry has long been recognized in the tensile testing of materials in which elongations are relatively small.* In the present study, the effect on superplas- tic extension of the ratio of specimen diameter to length was investigated and an analysis was made of strain distribution along the gage length. Superplastic alloys are characterized by having a flow stress sensitive to strain rate but relatively insensitive to strain.2"' In an earlier study,5 it was found that the strain-rate sensitivity of several low-alloy steels changed during the test and that the minimum value correlated best with total elongation. In the present study, the variation of strain-rate sensitivity during the straining of a lead-tin alloy was investigated. EXPERIMENTAL PROCEDURE Lead-tin eutectic alloy (32 pct Pb 68 pct Sn), made from high-purity lead and tin, was cast in the form of 1-in. diam rod. The rod was cold-rolled in stages to 0.25 in. diam and then swaged to 0.125 in. diam. Samples were cut from the rod at various stages of the mechanical working process. Tensile test specimens were then made by attaching threaded steel ends to the rods by an epoxy-base thermosetting adhesive which required a setting treatment of 2 days at room temperature. The rods were seated in the steel ends in holes approximately 0.01 in. oversize. The test pieces thus made were of various diameters and gage lengths. These were stored at a temperature of about -70°C (-94°F) until required for testing. The distribution of strain along the gage length of a specimen was determined at various stages of the tensile test. The lead-tin alloy was superplastic at room temperature and direct observations during testing were simple. The gage length was divided by reference marks into five initially equal units. These reference marks were made with ink and were reinforced during the test when the initial marks became faint. Photographs were taken, at intervals, of the deforming specimen and measurements of the elongation in each of the gage units were made on these photographs. Tests were also done on several superplastic low-alloy steels whose properties were described earlier.5 The chemical compositions of these steels are given in Table I. A diagram of the notched tensile specimen used in the steel tests is shown in Fig. 1. The specimens were tested at 900°C (1650°F) in a furnace through which a mixture of He + 2 pct H was continuously circulated.5 RESULTS Strain Distribution. Approximately 20 tests on lead-tin alloy specimens were conducted to determine the strain distribution during the test. An example is shown in Fig. 2 of the strain distribution in the gage

Jan 1, 1969

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation. A series of temporary and permanent water pumping stations is planned. Generally, the temporary stations are located above major aquifers to facilitate water removal while sinking through the aquifer and the permanent stations constitute what, in the final mode, will be the mine dewatering system. In addition, Phillips Uranium Corporation has In- stalled and is maintaining a system of depressurization wells that temporarily pump the major aquifers and considerably reduce the water inflows during shaft construction. The major aquifers are also chemically grouted prior to sinking. Site work for the project was initiated in the fall of 1976. Full scale shaft sinking commenced in November of 1977 on the 4.88 m (16 ft) diameter ventilation shaft and on the 5.49 m (18 ft) production shaft by another contractor. Harrison Western Corporation began work on the project on November 4, 1979 wlth the production shaft at a depth of 633 m (2,076 ft) and the ventilation shaft at a depth of 474 m (1,554 ft). This paper will address only the portion of shaft sinking completed by Harrison Western. Geology and Hydrology The Nose Rock Project is located on the Chaco Slope in the southern extreme of the San Juan Basin in northwest New Mexico. The southern San Juan Basin is generally bound by the Defiance Uplift to the west, the Zuni Uplift to the south and the Nacimiento Uplift to the east. The Grants Mineral Belt occupies most of the southern portion of the San Juan Basin and this project is located on the northern extreme of the Grants Mineral Belt. The San Juan Basin is comprised of sedimentary rock of continental, marginal-marine and marine origin, that dip northward from the Zuni Uplift and Chaco Slope into the interior of the San Juan Basin. (See Figure 2) Major Formations The major geologic formations to be penetrated range from mudstone and shales to siltstones and sandstones. The sandstones are highly productive aquifers which, under static conditions, would flow artesian. Water temperatures in the aquifers are high and therefore are a force to be dealt with. Temperatures range from 18ºC (65OF) in the upper aquifers to 48ºC (118º'F) in the lower. The mudstones are generally bentonitlc. (See Figure 2) GALLUP SANDSTONE: The Gallup Sandstone is the first major regressive wedge in the San Juan Basin of the Cretaceous era and at this project is about 35 m (115 ft) thick. It is medium grained and prior to depressurization carried a hydrostatic water pressure of over 72.5 kg per cm2 (1,031 psi) which 1s artesian. Compressive strength ranges from 334.7 kg per cm2 (4,760 psi) to 421.8 kg per cm2 (6,000 psi). Water temperature is approximately 30°C (86°F).

Jan 1, 1982

By D. P. Kedzie, R. A. Dodd

The fatigue strength, fatigue hardening, and effect of fatigue deformation on subsequent age hardening of supersaturated Al(Cu) solid solutions have been determined as functions of alloy composition and temperature. The fatigue strength/tensile strength ratios, determined at 150°, 25°, and -195°C, decreased with increase in alloy content for all temperatures, but the F.S./U.T.S. ratios at -195°C decreased much more rapidly than did the ratios for 150" and 25°C. This suggested that strain aging and/or age hardening occurred during tests at higher temperatures. Additionally, the F.S./U.T.S. ratios at 150°C exceeded those at 25°C for all compositions, indicating greater strengthening during fatigue at 150°C. The effect of fatigue or tensile deformation at 150°, 25°, and -195°C on subsequent age hardening showed that the deformatzon increased the rate of precipitation and indicated that mechanically produced vacancies were probably formed during deformation. Fatigue hardening was studied at 150°, 25°, and -195°C, and the effect of room-temperature rests after 10 and 100 cycles was examined. The results confirmed that strain aging occurred at the higher temperatures . DURING the last 15 years various mechanisms of fatigue crack nucleation and growth based on dislocation and vacancy interactions, operating singly or collectively, have been proposed. The probable consensus of present opinion is that the fatigue process in pure metals essentially involves dislocation interactions, and that vacancies formed by such interactions play a minor or inconsequential role. However, there is some evidence that age-hardened alloys tend to overage during fatigue, probably by local vacancy-enhanced diffusion, and strain aging also might be important in selected cases. Furthermore, it has been established that the behavior of quenched-in vacancies in Al(Cu) and other solid solutions is composition-sensitive. Therefore, it seemed worthwhile to investigate various aspects of the fatigue behavior of supersaturated Al(Cu) alloys and to examine the results in terms of vacancy-enhanced effects. EXPERIMENTAL The alloys used in this investigation were prepared from 99.994 wt pet A1 and OFHC copper, the latter containing 0.04 pet 0 as the principal impurity. Six alloys were made, containing, by actual analysis, 0.58, 0.96, 1.96, 2.85, 4.45, and 5.51 wt pet Cu. They were induction-melted in air in graphite crucibles, cast as 7-in. by 7/8-in.-diam rods in graphite molds, and hot-rolled to 5/8 in. diam. The experimental work was a three-part program involving the determination of a) 10' cycle fatigue stresses as a function of alloy composition and temperature; b) the effect of fatigue deformation on subsequent aging of the supersaturated alloys; and c) fatigue hardening as a function of alloy composition and temperature. For determining the 105 cycle fatigue stresses, a portion of the 5/8-in. stock was machined into Krouse rotating cantilever beam fatigue specimens, 2 in. in length by 1/4 in. minimum diameter. These were tested at +150°, 25°, and -195°C (liquid nitrogen) on a Krouse high-speed machine, with special weights to provide lower -than-normal loading ranges, this being necessitated by the small load requirements of those alloys of lower copper content. For the high-temperature tests a small resistance heater was designed to clear the collets and fit in between the chucks, while for the low-temperature tests a hollow nylon cylinder was used, having closed ends drilled to pass a fatigue specimen, and positioned similarly to the heater. A plexiglass container completely enclosed the fatigue machine; rubber gloves fixed to ports in the walls enabled the machine to be operated from outside the box. A tray of magnesium perchlorate dried the air in the container and prevented both atmospheric corrosion fatigue at room and elevated temperatures and troublesome ice build-up at low temperatures. A total of ten to fifteen specimens was used for each combination of alloy composition and temperature. The result of each test was plotted on a standard S-N diagram, and the next stress was selected on the basis of the trends indicated by previous specimens. In this manner a small portion of the S-N diagram was constructed, and the 105 cycle fatigue stress obtained. Small Krouse fatigue specimens were also used to study the effect of cyclic prestrain on subsequent

Jan 1, 1964

By E. M. Kalar, I. Iwasaki, J. D. Zetterstrom

Several methods of removing fatty acid coatings from iron ore flotation concentrates were tested both on a Mesabi oxidized iron ore and on a magnetic taconite concentrate, and their effects on the duplex flotation process and on pelletizing were compared. Either acid or alkali alone could not remove the coatings, but a combination of such reagents as lime and quebracho, calcium chloride and pyrophosphate, or sulfuric acid and an organic acid (oxalic, malonic, or citric acid) was quite effective. The use of activated carbon was found to be particularly promising. The removal of fatty acid coatings from iron ores is of much practical interest when a pelletizing process is being considered for a concentrate floated with a fatty acid collector or when a duplex flotation process is being considered for upgrading an oxidized iron ore. A duplex flotation process is a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process is being used in the Florida phosphate fields.' Although in northern Michigan mills fatty acid flotation concentrates have been pelletized successfully, at other locations fatty acid coatings on iron flotation concentrates have proved so undesirable in the agglomeration operation that other methods of concentration had to be sought.' Since fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates, a combination of reagents, such as lime and quebracho,3 lime and alkali phosphate,4 or sulfuric acid and oxalic acid,' has been proposed. It was also thought that activated carbon might be effective in removing fatty acid coatings due to its high adsorptive capacity. Activated carbon, with its enormous surface per unit of volume, is well known for its exceptional efficiency in removing organic pollutants from industrial effluents. This article presents the practical aspects of the above methods when they are applied to the duplex flotation process and to the pelletizing of iron flotation concentrates. The article also includes a preliminary investigation of the common parameters involved in the depressant activity of the reagents. EXPERIMENTAL WORK Initially, the experimental work was directed towards the optimization of each method for the removal of hydrophobic coatings from iron oxide surfaces floated with fatty acids. Subsequently, the methods thus optimized were tested in the duplex flotation process with an oxidized iron ore and in the pelletizing process with a magnetic taconite concentrate. Preliminary Flotation Tests: Although the three types of chemical treatment reported in the literature were briefly investigated for the purpose of comparison, major emphasis was placed during the preliminary flotation tests on the use of activated carbon because it was thought to have certain advantages over the chemical methods. LIME AND QUEBRACHO - To obtain a flotation concentrate for optimizing the lime and quebracho method of fatty acid removal, the magnetic taconite concentrate was used. The concentrate had a size consist of 90% passing 325 mesh and analyzed 64.5% iron. After a few preliminary tests the fatty acid flotation procedure with the magnetic taconite concentrate was standardized as follows. A 1200-g sample of the magnetic concentrate was pulped in a Fagergren laboratoy flotation cell to 40% solids, conditioned with 0.5 lb of soda ash per ton for 2 min, and then further conditioned with 1.0 lb of Acintol FA-2 per ton for 2 min. After 5 min of flotation, recovery was nearly complete, averaging 98.6% of the weight and 98.7% of the iron. The cell product, which amounted to 1.4% by weight and analyzed 63.2% iron, consisted mainly of relatively coarse middling particles. Since the repro-ducibility of the flotation concentrates produced by this procedure was vey high, the same procedure was used to prepare fatty acid concentrates for each of the six tests of the lime and quebracho method. To test the removal of the fatty acid from the magnetite surfaces by the lime and quebracho method, a fatty acid froth product was returned to the flotation cell, repulped by 30 sec of agitation, and then con-

Jan 1, 1968

By W. O. Philbrook, R. S. Kaplan

Rates of oxidation were studied for levitation-melted samples of Fe-C, Fe-Si, Fe-C-Si, Fe-C-P, Fe-C-Mn, and Fe-C-S alloys oxidized by mixtures of either 5 or 10 pct O2, in helium at several temperatures in the range 1850o to 2050°C. The concentrations of the oxidized elements decreased linearly with time. Mass transport in the gas phase was found to be the rate-controlling step. Ilowever, a mulliple -film model was necessary to account for the flux of iron and manganese vapor counter to the oxygen flow. THE advent of the basic oxygen and spray-refining processes of steelmaking has generated considerable interest in the kinetics of reactions between oxygen-bearing gases and liquid iron alloys. The object of this research was the determination of the role of mass transport in the gas and metal phases and of surface chemical reactions in the overall oxidation process. Of the reactions for elimination of elements dissolved in liquid iron, the oxidation of carbon has been investigated most extensively. Studies by Fuji and Ura,1 Fuji,' and Gunji et a1.,3 done with pilot-scale basic oxygen furnaces, indicated that mass transport of gaseous oxygen was rate controlling when the metal carbon content was greater than 0.15 to 0.30 pct. When the carbon content was less than this critical amount, diffusion of carbon dissolved in the iron was thought to be rate limiting. L. A. Baker et a1.4,5 levitated samples of iron-carbon alloys and oxidized them in CO-CO2, CO-C02-He, and O2-He atmospheres at 1660°C. These investigators found that the metal carbon concentration decreased linearly with time and their samples exploded when the carbon content fell below about 0.8 pct. They concluded that the rate-limiting step was the transfer of oxidant to the gas-metal interface. A model based on this rate-limiting step predicted decarburization rates within a factor of two of those experimentally observed. The explosion of the samples was attributed to a shift in rate-controlling step from gas-phase mass transport to transport of carbon dissolved in the metal. L. A. Baker and R. G. ward6 and R. Baker7 used freely falling droplets to investigate oxidation kinetics. In both papers, the authors speculated that flame fronts may have been partially responsible for the lack of better agreement between experiment and theory. Swisher and Turkdogan8 oxidized liquid iron having an initial carbon content of 0.97 pct with CO-CO2 and CO-C02-Ar mixtures at 1580°C. They concluded that a surface reaction was the rate controlling step. Iron-silicon alloys have been oxidized by R. Baker7 and Filipov and Martynov.9 R. Baker 7 also studied iron-carbon-silicon alloys falling as liquid droplets through oxygen. He found that the rate of both carbon and silicon oxidation varied inversely with the drop radius. When the initial silicon concentration was greater than 6 pct, the samples cooled during their fall. Manganese oxidation has been studied by R. Baker,7 and by Filipov and Martynov.9 ward10 investigated the loss of manganese from liquid iron under vacuum. He found that mass transport of manganese vapor was rate limiting in argon atmospheres of 0.02 torr to 700 torr pressure. Iron-sulfur alloys were desulfurized with H2-He and H2-Ar mixtures by Peters et al.11 A model based on the transport of H2S from the gas-metal interface into the bulk gas gave fair agreement between the predictions of the model and the experimental results. EXPERIMENTAL TECHNIQUE Essentially, the technique consisted of using helium-oxygen gas mixtures to oxidize levitated samples of liquid binary and ternary iron-base alloys. The fused silica reaction tube is shown in Fig. 1. The coil design is similar to that of L. A. Baker et al.4'5 A Tef-lon-sheathed, ferritic stainless steel lifter (B) and an alumina pedestal (C) were used to support the sample in the coil prior to levitation and for the recovery of the sample. Samples were inserted into

Jan 1, 1970

By R. J. Stoehr, F. Howell

Since the ore mined in the Grants-Ambrosia Lake uranium area is taken from a water-saturated sandstone formation, part of the milling operation includes a drying process. The authors discuss the merits and disadvantages of two methods: natural drying and mechanical gas-fired drying; operating and cost data are included. In the Grants-Ambrosia Lake uranium area, approximately 7000 tons of ore are mined each day from a water-saturated sandstone formation. This ore is sampled and treated at four separate milling operations. Prior to the design and initial construction of the milling facilities, very little was known as to the physical properties of the ore which would be handled in the sampling and crushing facilities at the mills. All four mills initially were constructed without ore-drying facilities. As mining proceeded, it was determined that, even after drying the ore in place by use of drainage development underground, the moisture content of the ore as hoisted averaged approximately 18 pct. Actually, some of the mines produced ores which resembled cream-of-wheat in character and had a moisture content in excess of 24 pct. Each of the four mills had a differently designed sampling and crushing plant; therefore, the moisture content of the ores had varying adverse effects upon the operation of the plants. It was determined after some experience that most of the sampling and crushing facilities could not economically handle ore if the moisture content was greater than 10 pct—one operator considers 12 pct moisture as a maximum. In all of the plants, moisture content over 8 pct increases costs to some extent. In addition to the added sampling and crushing costs, some of the mills were located 15 to 20 miles from the mines and the high moisture content of the ores increased the haulage costs from the mine to the mill. It was generally conceded that it was necessary to employ some method to reduce the moisture content of the ore prior to sampling. Several methods were considered: 1) natural drying at the mine site, 2) mechanical gas-fired drying at the mill site, 3) mechanical gas-fired drying at the mine site, 4) radiant heating on concrete clabs, and 5) infrared shed drying. After preliminary investigation all possibilities but natural drying and mechanical gas-fired drying at the mill site were eliminated. NATURAL DRYING A cooperative feasibility study was conducted on the natural drying method. This study indicated the following: 1) During summer months May through September, ore piled 4-ft deep would dry from +20 to +10 pct HzO in 30 days with no mechanical turning. 2) In the first four days after piling a reduction of 5 to 7 pct total moisture content was accomplished by drainage and absorption of the water into the underlying ground on which the ore was piled, providing the ground surface absorption rates approached 10 gal per sq ft per day. After the first four days the decrease of moisture caused by drainage was practically nonexistent. 3) In the summer months drying by evaporation amounted to approximately 0.1 pct decrease in total moisture per day and mechanical turning of the ore could increase this as much as three times. 4) Climatic conditions of the area indicated that: a) Air temperatures averaged 64' May, June, July, August, September; 41" October, November, December, March, April; 31" January, February. b) Average rain fall was 10 in. with 40 pct of this occurring during July and August. c) Only on very rare occasions were there over five consecutive days with below freezing temperatures. d) The annual evaporation rate was approximately 75 in. On the basis of this study, two of the mill operations decided to attempt to meet the moisture specifications by natural drying supplemented by mechanical turning. The other two operations decided upon rotary gas-fired drying at the mill site. The natural drying method has been quite successful in practice. The ore running approximately 18 pct moisture is trucked from the head frame and piled in rows about 6 ft wide, 3 1/2 ft deep, 5 feet apart during the months of May through September. In approximately 30 days this ore will

Jan 1, 1961

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963

By P. S. Kotva

Dislocation substructures in superalloy matrices of varyzng co)npositions have been studied. In general, it has been found that the alloys can be classified into ''high", ''medium", and "low" stacking fault energy classes based on the type of dislocation substructure observed in the matrix and that the substructure can be correlated to the stacking fault energy. The effect of different types of dislocation substructure and dislocation reactions on the intragranulur precipitation of carbide phases has been studied. In a Ni-Cv-Mo-Fe matrix, precipitation of MC carbides in association with stacking faults has been observed. In most superalloys, solid-solution strengthening and precipitation hardening are the chief mechanisms employed to achieve strength. The latter contribution to strength is usually achieved by the precipitation of / in certain wrought alloys. Insufficient attention has been given to the problem of obtaining strength in su-peralloys by controlling precipitation of carbides on imperfections within the matrix. The present work was undertaken to investigate the dislocation substructure in various superalloy matrices, to study the effect of such substructure on subsequent precipitation of carbides in the matrix, and to investigate whether certain modes of precipitation of carbide phases found in austenitic stainless steels2"4'6 would occur in nickel-base alloy matrices with dislocation substructures of the same type as those found in austenitic steels. 1) EXPERIMENTAL TECHNIQUES Five-pound heats of the various alloy compositions reported here were vacuum-cast. The ingots were given light deformation by rolling to break up the as-cast structure and then homogenized for 24 hr. HASTELLOY alloy X (nominal composition: Ni-2OCr-17Fe-8Mo-0.05C) was homogenized at 2150°F and In-cone1 625 (nominal composition: Ni-20Cr-5Fe-8Mo-3.5Cb-0.05C) was homogenized at 2280°F. Fabrication of 0.004-in. sheet was achieved by cold rolling with intermediate annealing treatments being carried out at the same temperature as those used for homogeniza-tion. Each solution anneal was followed by quenching. The aim of this procedure was to redissolve as much of the primary carbide phase as possible. Samples of the 0.004-in. sheet were cut and encapsulated in quartz capsules and then heat-treated in the tube furnaces. Thin foils were prepared using an ethanol-10 pct perchloric acid bath at 32°F and at a voltage of 22 v. A "window" technique was employed. Observations were made on a JEM-7 electron microscope operating at 100 kv. 2) EXPERIMENTAL RESULTS a) Types of Dislocation Substructure. Fig. 1 shows a schematic correlation between stacking fault energy, SFE, and the type of dislocation substructure observed in various matrices of nickel- and cobalt-base alloys. A precise quantitative determination of stacking fault energy is not implied in the figure but the correlation between stacking fault energy and the type of dislocation substructure obtained allows alloys to be divided into three classes in analogy with the classification employed by Swann and ~uttin~' for binary alloys of copper. Class I alloys are associated with a "high" SFE and show a cellular substructure of dislocations as typified by the micrograph of a thin foil of pure nickel deformed 4 pct at room temperature in Fig. 2. With decreasing SFE the tendency toward cell formation is lessened and dislocations tend to be arranged in coplanar groupings. Examples of this class of alloys with "medium" SFE are provided by the mi-crostructure of solution-heat-treated, quenched, and deformed thin foils of HASTELLOY alloy X, "Waspaloy" (prior to any aging), and Inconel 625. Fig. 3 shows a thin-foil micrograph of an alloy of Inconel 625 composition, solution-heat-treated, quenched, and deformed 5 pct at room temperatures. No evidence of any cell structure can be obtained in materials of "medium" stacking fault energy, Fig. 3, even after severe deformation. The stacking fault energy of the alloy shown in Fig. 3 is, however, not low enough to make the dissociation of dislocations visually obvious. As stacking fault energy decreases further, with successive addition of solute in the matrix, there is an increased tendency toward dissociation of dislocations and cross slip becomes progressively more difficult. Eventually, when the stacking fault energy is "low" enough, complete dissociation of dislocations is seen to occur as shown in Figs.

Jan 1, 1969

By Craig R. Barreft, Oleg D. Sherby

The steady-state creep characteristics of pure polycrystalline copper were studied in the temperature range 400" to 950°C and in the stress range 400 to 7000 psi. Tests were conducted in dry deoxidized hydrogen and all specimens exhibited high ductility before fracture. Two activation energies for creep were established as a function of temperature. Above about T/T, = 0.65, the activation energy for creep was 48,000 cal per mole whereas between 0.5 and 0.65 T, it was 28,000 cal per mole. The observed temperature dependence of the activation energy for creep follows the same trend as exhibited by the self-diffusion coefficient of copper in copper single crystals and silver in silver single crystals. It is therefore believed that the rate-cmtrolling mechanism in creep of copper in the stress and temperature range studied is diffusion-dependent and is probably associated with a dislocation-climb process. The low activation-energy region is attributed to enhanced volume difFusion from the presence of dislocations which act as short-circuit paths for diffusion. THERE is extensive experimental evidence1,2 that the activation energy for creep, Q,, for pure poly-crystalline metals tested at temperatures above one half the absolute melting temperature (0.5 Tm) is a constant and equal to the activation energy for volume self-diffusion, Qsd This equality is generally interpreted as meaning that creep in this temperature range is controlled by a dislocation-climb process. The existence of high-temperature creep activation energies not equal to the respective self-diffusion values has been suggested both theoretically3"5 and experimentally.6-8 Two examples of apparent nonequality between Q, and Qsd have been reported for the cases of silver7 and copper,' where activation energies for creep much lower than those for self-diffusion persist to rela- tively high temperatures (up to 0.6 T,). These observations suggest that dislocation climb may not be the only important process in the high-temperature deformation of these metals. That dislocation climb does indeed occur relatively slowly in these two metals due to their low stacking-fault energy has been suggested by many investigators.9-10 Although the creep behavior of copper has been studied extensively at low temperatures, the high-temperature activation energy for creep is not well-defined. The data of Feltham and Meakin8 indicated that Q, is temperature-dependent above one half the melting temperature, equaling a value of -30,000 cal per mole at temperatures up to 550°C and increasing to a value of -49,000 cal per mole at 700°C. No data has been reported above 700°C. The value of 49,000 cal per mole is very near the value of Qsd for copper reported by Kuper et al." as 47,100 cal per mole. In view of the lack of high-temperature creep data and the apparent temperature dependence of Q, for copper the present investigation was undertaken to determine the value of Q, over the temperature range of 400" to 950°C. It was hoped that such a study would clearly document the temperature dependence of Q, and yield significant information as to the nature of the rate-controlling creep mechanisms. MATERIALS AND PROCEDURES The material used in this investigation was high-purity OFHC copper. After rolling and recrystal-lization treatments spectrographic and chemical analyses showed only 0.0008 pct Ag, 0.0002 pctCa, 0.0002 pct H2, and 0.002 pct O2 as trace impurities indicating a purity of greater then 99.995 pct. Specimens were machined from cold-rolled sheet and the gage sections polished with 2/0 emery paper prior to annealing treatments. Annealing was done in both vacuum and dry deoxidized hydrogen atmospheres. No variation in creep strength was found as a result of the different annealing atmospheres. The final annealing temperature was either 700°, 800°, or 1000°C depending on the temperature range to be studied. These treatments resulted in average grain diameters of 0.03, 0.4, and 1.0 mm, respectively. The precise mechanical-thermal history of these

Jan 1, 1964