Search Documents

By C. Ernest Birchenall, Gerd M. Rosenblatt

The pressure and molecular weight of the antimony vapor over solid solutions of tin in antimony, containing 97.4, 94.9, 93.0, and 90.7 at. pct Sb, have been measured from 445° to 545°C by the torsion-effision method. The vapor is all Sb, within experimental error. A solidus curve which differs somewhat from the accepted curve has been calculated using the measured antimony activities. Metallographic examination of additional annealed alloys substantiates the accepted solidus. The solid solutions, which show negative deviations from ideality, probably do not deviate greatly from regular solution behavior. HANSEN' considers the Sb-Sn phase diagram to be well established with the exception of the boundary of the (Sb) phase.* Although there have been no pre- Their data can be combined with data for the solid alloys to calculate the solidus curve of the (Sb) phase. This paper presents measurements of the pressure ant1 molecular weight of antimony over Sb-Sn solid solutions containing 97.4, 94.9, 93.0, and 90.7 at. pct sb. Measurements were made by simultaneous use of the volmer3 torsion and Knudsen, effusion methods. The results of these measurements have been combined with the vapor pressure of pure antimony5 to obtain the activity of antimony in the primary solid solutions. The solidus curve calculated from these data differs somewhat from the accepted curve and is rather uncertain. Metallographic examination of Sb-Sn alloys was carried out to clarify the position of the solidus of the (Sb) phase. EXPERIMENTAL The apparatus and technique have been described previously.5 The measurements were made with the same effusion cells and torsion wire used in the measurements on pure antimony. The torsion measurements were calibrated with mercury at 30" using a mercury vapor pressure of 2.96 x 10-3 mm Hg determined by concurrent, absolute, weight-loss experiments. As in the measurements on pure antimony, an extraneous vapor was observed to distill off during the first run after the cell had been loaded with A fresh sample of alloy and during the first minute or two of every run. The change in composition after a series of runs with one sample was of the order of 0.1 at. pct and thus completely negligible in the calculation of the thermodynamic properties. The alloys were prepared from pieces of Merck antimony and Matheson, Coleman, and Bell reagent-

Jan 1, 1962

By Jesse O. Betterton

In the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200' to 1300" I?. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accomplish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flour of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes. Essentially this process consists of circulating the lead by means of a pump in a kettle through a closed reaction cylinder, gaseous chlorine entering the reaction cylinder with the stream of lead from the pump. Molten zinc chloride is thus produced and is discharged together with

Jan 1, 1937

By Raymond Mancha

TO determine the optimum inside dimension of an airshaft, it is necessary to strike the proper balance between the cost of power for air friction and turbulence losses within the airshaft, on the one hand, and the cost of sinking the airshaft, on the other. An airshaft larger than necessary is extravagant because the increased amortization rate exceeds the reduction in power cost. Conversely, an airshaft smaller than is needed wastes more power than can be justified by the corresponding reduction in amortization rate. The airshaft power is a function of the air volume Q cu. ft. per min. and the air-pressure drop p in. water gauge across the airshaft. † The airshaft pressure drop is calculated by the formula: R X l X O X Q2 P= 5-2 X A3 wherein R is the air-friction coefficient for the portion of the airshaft 1 ft. deep, 0 ft. in perimeter and A sq. ft. in area, when passing an air volume of Q cu. ft. per minute. The airpower w kw. dissipated within the airshaft is computed by the formula: w= 0.746Q X P 6345 With a combined over-all unit efficiency of the fan and drive of E per cent, the air-shaft power requirements become W = 100w There are 8760 hours per year, so with energy at I cent per kilowatt-hour the annual cost per kilowatt for continuous operation is $87.60; therefore, with energy at C¢ per kw-hr. the annual airshaft power cost MI dollars per year becomes: M1 = 87.60W X C which, expressed by the component parts, becomes: M1 V 5.2X4' / XQ Z 0.746 X 100 X 87.60 X C V 60 X E ) The amortization rate a dollars per year per dollar invested includes both depreciation and interest on the investment. These in turn involve the expected useful life of the airshaft and available molletary interest rate. For the purpose of this discussion the cost of airshaft sinking is assumed to comprise a fixed move-in charge Y dollars, which covers the cost of transporting, erecting and removing the shaft-sinking equipment and is independent of the air-shaft size. Also, it is assumed that the cost of shaft lining, if any, is fixed at $X per cu. yd. of lining material and that excava-

Jan 1, 1947

By Geo Ashley

THE following paper is intended to be suggestive only, and to open the way for discussion and further observation. Its preparation was requested only two days before the time limit set for the submission of the papers comprising this symposium. Thus no time existed for detailed studies so it is largely a memorandum of such facts as have come incidentally to the notice of the writer in the study of coal in the field. The field study of sulfur in coal has received very little special attention or description from coal students. The presence of sulfur concretions is noted in hundreds of descriptions, and certain benches of a coal bed may be described as "sulfury" or the presence and position of sulfur bands may be noted in coal sections in connection with sampling. It may be accepted that some sulfur is present in all coal. The amount varies greatly in different regions, in different beds, and in the same bed in different areas. The anthracite of Rhode Island comes the nearest of any coal known to the writer of being free from sulfur, several analyses of that coal showing less than 0.1 per cent. Subbituminous coals in Colorado in a few places have close to 0.2 per cent. of sulfur on the dry-coal basis and in other states subbituminous coals approach this lower limit. Bituminous coals seldom run under 0.4 per cent. of sulfur on the dry basis, though in a few places dry bituminous coals in Colorado and Washington have between 0.3 and 0.4 per cent. The better known bituminous coals have almost everywhere over 0.4 per cent. The best of the Pocahontas and New River coals run close to 0.4 per cent., but there is very little commercial coal in Pennsylvania, Ohio, Indiana, Illinois, Kentucky, or the other states that runs under 0.5 per cent. on the dry basis. From these minimum figures, the amount will range up to 5 or 6 per cent. or higher if visible sulfur is not excluded. It must be remembered that the usual -analysis of a coal bed is not intended to give the total proportion of sulfur in the bed but the amount in the coal after the removal of the more obvious and larger sulfur masses.

Jan 9, 1919

By Leslie Burris, J. C. Hesson

The diffusivity of uranium in liquid cadmium has been measured as a function of temperature by the capillary -bath technique. The diffusivity measurements were made at 4509 500°, 575º, and 650°C, over which temperature range the diffusivity of uranium varied from 1.3 to 2.3 x 10-5 sq cm per sec. The diffusivity of uranium in cadmium was less than that predicted by the Einstein-Stokes equation. VERY little information is available on the diffusivity of uranium in liquid metals. Bonillal has reported a single measurement of the diffusivity of uranium in bismuth. Measurement of the diffusivity of uranium in cadmium was undertaken, not only to supply data in an area in which a dearth of information exists, but also because of a need for this physical property measurement in connection with mass transfer studies now underway in the U-Cd system at Argonne National Laboratory. The capillary-bath method used in this work has been successfully used by other workers2"4 to obtain diffusivities in liquid metal systems. Although considerable experimental technique is required to obtain reliable diffusivity measurements, the basic information required is only that of temperature, capillary tube length, the initial and final compositions of the alloy in the capillary tube, and the composition of the bath into which the solute element is diffusing. From these measurements, diffusivities may be calculated using Fick's law. The diffusivity equations are presented in the Appendix. Equations which are often used to predict diffusivities in dilute solutions5 are the Einstein-Stokes equation: D= (kT)/(6pµr) and the Eyring equation: D = (?,kT/?y?zp), where D= diffusivity (sq cm per sec), k = Boltzman's constant, T= temperature ("K), p = viscosity (poises), r = radius of diffusing molecule or species (cm), and A,, Ay, and A, are the diameters of the diffusing molecule in the three axial directions. For round molecules, the Eyring equation gives values which are 37r times larger than the Einstein-Stokes equation. In this work, the experimental values were compared to the Einstein-Stokes equation. Experimental values of diffusivities in liquid metal systems usually lie between those predicted by the Einstein-Stokes and Eyring equations. The viscosity values for cadmium were obtained from the Liquid Metals Handbook.6 EXPERIMENTAL APPARATUS AND PROCEDURE The general procedure employed consisted of rapidly immersing in a molten cadmium bath containing a negligible amount of uranium a capillary

Jan 1, 1963

By H. F. Gossenberger, J. J. Tietjen, J. J. Gannon, C. J. Nuese

External quantum efficiency measurements at 300" and 77°K are presented for vapor-grown GaAs and GaAs1-xPx electroluminescent diodes as a function of junction depth and doping. In GaAs, external efficiencies are found to decrease exponentially with increasing junction depth, defining an average absorption coefficient of 900 cm-1 at 300°K and 350 cm-1 at 77°Kfor epitaxial layers of p-type GaAs. It is shown that photon absorption losses dominate at room temperature and, in fact, account for most of the external efficiency degradation between 77° and 300°K. Healever, the internal ('junction) quantum efficiency is also found to decrease by a factor of 3.5 between 77" ALTHOUGH rapid progress has been made in recent years with GaAs, Gap, and their alloys for use in electroluminescent diodes, there are still important unknown factors related to the performance of these de- and 300°K. The dependence of GaAs efficiencies on donor and acceptor concentrations is presented, illustrating best efficiencies at donor concentrations of 1.5 to 2x 1018 cm-3 . External efficiencies are found to be independent of acceptor concentrations less than 3 x 1019 cm-3 but to degrade at higher doping. The fabrication of GaAsi-xPx electroluminescent diodes is briefly discussed. External efficiencies here for planar uncoated diodes are about 0.035 pct at 300°K and 0.4 pct at 77°for x = 0.42. A brightness of about 8500 ft-Lamberts is attained at 77°K and of 315 ft-Lamberts at 300° K. for curvent densities of 10 amp per sq cm. vices. For example, although the external efficiency is known to decrease by factors of typically 10 to 30 between 77°K and room temperature, the exact causes of this are still uncertain. Experimental results of ill' and carr2 with zinc-diffused electroluminescent diodes suggest that this external degradation is almost entirely due to increased absorption losses at room temperature, with a relatively temperature-independent internal efficiency; recent calculations by Gonda et al.3 corroborate this hypothesis. In contrast, Pilkuhn and Rupprecht4 find the internal efficiency of solution-grown GaAs laser diodes to degrade from 100 to 66 to 40 pct as the temperature is increased from

Jan 1, 1969

US 4,141,854-Method of resolving water-in-oil emulsions from the organic solvent extraction of uranium from an aqueous ore leach solution The emulsion is treated at optimum temperature with a water-soluble acrylamide copolymer which contains 5-50% by weight of a lower alkyl substituted tertiary aminoethyl methacrylate or quaternary ammonium salts thereof The emulsion is broken, enabling recovery and reuse of the organic portion of the emulsion A M Pavilcius and M A Latko, assigned to Nalco Chemical Co Feb. 27, 1979 3 pp (252-301 1W) Filed: 12-14-77 (860,542). US 4,142,952-In the recovery of copper from an ore leach solution, the solution is contacted with a water-immiscible organic solvent containing 5 to 20 g/L of o-hydroxyaryloxime and 2 to 20 times the weight of the o-hydroxyaryloxime of nonylphenol The loaded solvent phase is separated from the aqueous phase and stripped with sulfuric acid Copper is recovered rapidly and in high yield from aqueous solutions containing high copper concentrations R F Dalton, as¬signed to Imperial Chemical Industries Ltd Mar 6, 1979 6 pp (204-106) Filed 1-3-77 (756,067). Priority: United King¬dom, 1-30-76 (3788/76), 6-15-76 (24722/76), and 10-21-76 (43711/76). Same- British 1,549,615, dated Aug. 1, 1979 US 4,148,631-In the recovery of nickel and cobalt from a mixed sulfate ore leach solution, both metals are extracted by means of a cationic extractant, the loaded extractant treated with an aqueous chloride or thiocyanate solution to back extract the cobalt, and the cobalt then recovered by solvent extraction or ion exchange with an anionic extractant Recovery is effected in a relatively few extraction steps. F Babjak, V A Ettel, and K. R Dymock, assigned to Interna¬tional Nickel Co , Inc, Apr. 10, 1979 6 pp (75-101 BE) Filed¬7-27-78 (928,401). Priority- Canada, 12-28-77 (293,967) US 4,148,813-An improved extractant for use in the recov¬ery of nickel and cobalt from an ore leach solution comprises a water immiscible organic solvent system containing solubilized mercaptide ions, e g , dodecanethiol. Cobalt and nickel mercaptides solvated in the organic phase are easily stripped in the presence of carbon monoxide and an aqueous alkaline solution A. S. Rappas and J. P. Pemsler, assigned to Ken¬necott Copp

Jan 1, 1980

By P. Greenfield, P. A. Beck

RECENT work by J. Darby, Jr. in this laboratory has shown that the reported vanadium-rich limit of the s phase in the Co-V system at 1200°C is in error. The appearance of a second phase in s actually is restricted to alloys containing over 68 atomic pct V. The error in the original value is due apparently to a reaction that takes place along the numerous cracks in the s specimens between the alloy and the impurities present in the He + 8 pct H atmosphere in the annealing furnace. Such a reaction and the consequent appearance of a second phase can be suppressed if the alloys are sealed under vacuum in Vycor tubing. The new value of 68 atomic pct V for the vana-dium-rich limit of the s phase in the Co-V system effects slightly the s compositions calculated from average values of N, and N,. for various s phases. The standard deviation between experimental mean compositions and those calculated from the assumption that s is characterized by a constant number of 3d + 4s electrons per atom (N,), is slightly reduced from 9.1 to 8.8 pct. The maximum divergence for the V-Mn s phase is reduced from 15.5 to 14 atomic pct. The standard deviation calculated from constant electron vacancy numbers given by N.. = 4.66 (Mo + Cr + V) + 3.2 (Mn) + 2.2(Fe) + 1.71(Co) + 1.6(Ni) is now greatly reduced, as the maximum divergence for this correlation previously occurred in the V-Co system. This maximum divergence is reduced from 7.6 to 2.3 pct, and the standard deviation for all s- phases is reduced from 4.1 to only 2.9 pct. The correlation for electron vacancy numbers given by N. 5.66 (V when with Ni or Co) + 4.88 (V when with Mn or Fe) + 4.66 (Cr + Mn) + 3.3 (Mn) + 2.66 (Fe) + 1.71 (Co) + 0.61 (Ni) is made slightly worse, and the standard deviation increases from 2.8 to 3.9 pct. These changes, however, do not affect the conclusions of the paper.' The deviation between calculated and experimental s compositions is much less for either one of the electron vacancy correlations than for the correlation with the number of 3d + 4s electrons.

Jan 1, 1955

By K. Nassau

The Effect of tin and hydrogen on the C0 parameter of a titanium. specimens were capsule cooled in water to eliminate contamination by water. Deybe-Scherrer photograms were obtained in a 114.6 mm camera with CuKa radiation. The parameters shown in Table I and Fig. 1 were calculated from the 213 (8569°) and 302 (8173.5°) reflections? no attempt being made to correct for systematic errors. The principal difference in method of preparation of specimens between this investigation and that of Worner was the use of pickling by the latter to produce X-ray diffraction samples. The possibility that hydrogen introduced by pickling was responsible for the lower a and c-parameters was investigated with the same 80 pct HNO3- 20 pct HF solutions used by Worner. The 6 and 10 at. pct specimens, the parameters of which had already been determined, were pickled and the c-parameters obtained are also shown in Fig. 1. The a-parameters, not shown, are also diminished. The quality of the lines obtained from the unetched and etched samples was unchanged, being quite sharp in both cases. It is quite possible that if corrections for systematic error carried out that the parameters obtained for the unetched samples would approach the data of Worner. In any event, the parameters of the etched samples would be still lower. The data obtained here is evidence that hydrogen in solution has contracted the c and a -parameters. Crystallographic Angles of Calcium Tung-state (Tetragonal, c/a = 2.169) K. Nassau In connection with the preparation and orientation of single crystals of calcium tungstate (Scheelite -CaWO4), the need arose for a stereographic projection for this tetragonal material. There appear to be no tetragonal projections with a c/a ratio above that of indium1 (c/a = 1.522) in the literature. In addition to its use for calcium tungstate, such a projection might find other more general applications and is accordingly presented below. The most recent X-ray diffraction work on CaWO4 is that of Swanson, Gilfrich, and Cook,2 where a summary of previous work is also found. Lattice parameters given are: a = 5.242A, c = 11.372A, and c/a = 2.169. The material is tetragonal with space group Table I, giving angles between crystallographic planes (HKL) and (hkl), was calculated from the formula3

Jan 1, 1961

Records of coal in Colorado begin only a few years before the Civil War. In 1859 Macomb reported beds of lignite on both sides of Galisteo Creek, and in the foothills of the Placer Mountains, a place where an outburst and overflow-of trap had changed the lignite into bright, hard anthracite.1 The Union Pacific Railroad sent Joseph T. Hodge to investigate the coal deposits in the Rocky Mountains, close to the projected line, in the fall of 1863. He was told of coal on South Boulder and Rock Creeks, and that somewhere on Lodge Pole Creek it was being worked for supplying fuel for stage stations; a bed was also reported seven miles north of the stage road between Laporte and Latham. It was only in the vicinity of Denver that coal mines were being worked to any extent; these openings were on Coal Creek about 22 miles north of the town, said to have been opened in. 1860. The coal was used by the smiths with ,difficulty and slacked badly on exposure., Some coke was made from one of the seams, the coke being preferred to the raw coal by smiths. Another district was opened along South Boulder Creek, about two and a half miles from the base of the Rocky Mountains, two mines being worked to supply the Denver market.2 Hayden reported a large bed of coal at Golden in 1861 and of having seen a similar one in 1862 about 65 miles east of Pikes Peak, and in 1866, he saw large beds on Rock Creek 16 to 19 miles from Golden. In 1867 he saw the Belmont or Marshall's mines opened in 1863 on South Boulder Creek, which he said was the finest exhibition of coal in the state. The next one was the Murphy mine, on Ralston Creek, five miles north of Golden. A mine was also being worked near Canon City at that time.3 The coal at Golden was being worked in 1864.4 In 1867 the coal mined at Golden was being used in a firebrick' works. At Canon City and other places on the waters of Arkansas River, coal was being mined for use in the valley towns, bringing $5.00 per ton at the mines.5

Jan 1, 1942

By A. Andreas

New Mexico retained its position in 1938 as the sixth largest oil-producing state, with a total production of 35,510,176 bbl. This was 2,875,598 bbl. less than the 1937 production of 38,485,774 bbl., or a decrease of 0.077 per cent, which was caused by the lack of pipe-line facilities and storage at the pipe-line terminals. The production for Lea County (excluding Maljamar) was 32,926,788 bbl.; for Eddy County (including Maljamar) was 2,225,411 bbl.; and for northwestern New Mexico (San Juan and McKinley Counties), 357,977 bbl. The average daily nonmarginal well allowable for Lea County on Jan. 1, 1938, was 65 bbl. At the close of the year it was 49 bbl. The average daily pipe-line runs for domestic consumption were less than the state allowables recommended by the United States Bureau of Mines. There was a demand for Artesia crude for foreign export, which if included in the daily production for New Mexico would be slightly in excess of the daily production recommended for New Mexico by the Bureau of Mines. The daily average production for the year was 97,329 barrels. There were 622 completions in the state, of which 520 were oil wells; 16 hydrocarbon gas wells; 5 carbon dioxide gas wells, and 81 dry holes. Of the dry holes 38 were in or near-by proven fields and the remainder, 43, were wildcats. Five new fields were discovered in New Mexico during 1938, three in Lea County and two in Eddy County. Southeastern New Mexico Lea County.—The Monumcnt field was the largest producing field in Lea County, with 9,440,334 bbl., and was closely followed by the Eunice field with 8,872,335 bbl. The Hobbs field was third with 5,010,414 bbl. The greatest activity in Lea County was in the Vacuum pool, with 129 completions, of which 126 were oil wells and three were dry holes. The Texas Company completed its Corbin NO. 1 in the KW 1/4 SW1/4 sec. 10, T. 18 S., R. 33 E. in August. This well was drilled to a depth of 5118 ft. in a white sand, encountering salt water. It was plugged back to 4315 ft, and pumped 43 bbl. of 36" gravity oil in 12 hr. It was approximately 6 miles southwest of the closest production in the Vacuum

Jan 1, 1939

By V. Balasubarmanian, Rajendra Kumar

ISOTHERMAL formation of martensite in a copper-aluminum-nickel alloy was previously reported by Hull and Garwood.' In the present work an attempt has been made to investigate some of the character- istics of the formation of isothermal martensite in binary copper-aluminum alloys containing 14.00 and 14.50 pct Al, respectively. Chill-cast alloys were prepared from OFHC copper and aluminum of greater than 99.5 pct purity. They were homogenized for 24 hr at 950° C. Polished samples were soaked at 1000°C and quenched in water to retain the p phase untransformed; martensite did not form during the quench. The surface was then repolished for isothermal microscopic studies at room temperature. The salient features of the martensitic transformation in copper-aluminum alloys observed in this investigation are: a) The transformation progresses (i) by nuclea-tion at new sites and (ii) by simultaneous slow isothermal growth of existing martensite plates. Slow isothermal growth of martensite has previously been observed by Holden2 in an uranium-chromium alloy and by Hull and Garwood in copper-aluminum-nickel alloy. b) Martensite plates nucleate preferentially at the pin holes formed during the casting of the specimen, Fig. 1. c) Some of the martensite plates pass right through other plates lying in their path, Fig. 1. d) Martensite plates cross grain boundaries without any change in the direction of growth. e) An irregular network of markings, Fig. 2, appears simultaneously with the formation of martensite. It was less prominent in the case of 14.5 pct alloy. The markings may arise due to spontaneous deformation under the lattice strains of the martensitic transformation. Crossing of martensite plates was first observed by Kulin and cohen3 when a high-nickel steel was cooled to 77°K. They suggested that the rapidly advancing plates atquire considerable kinetic energy and strike the obstructing plate with a momentum so as to nucleate the process on the other side of the plate. This, however, fails to explain the present observation where the slow isothermally growing martensite plates cross each other. Such plates would not possess large momentum to bodily displace the obstructing plate. Fig. 1 shows the martensite plates crossing each other without body displacements. This should be contrasted with Fig. 3 of Kulin and Cohen's paper where crossing of plates is accompanied by shearing or body displacements of the plates. The present observations can, how-

Jan 1, 1961

By L. F. Rooney

In June 1964 the Indiana Geological Survey discovered gypsum beds more than 10 ft thick in rocks of Devonian age in La Porte County, Ind. Although the extension of the Michigan Basin evaporites into northern Indiana has been recognized for some time, the gypsum beds have been regarded as either too thin or too deep for exploitation. Current Survey research, however, indicates that exploration by industry might find commercial deposits of gypsum less than 50 miles from Chicago. In four cores taken by the Survey within 1 sq mile in La Porte County, the maximum thickness of inter-bedded gypsum and anhydrite is 35.8 ft. Both gypsum and anhydrite beds contain irregular masses of limestone and dolomite that average a few inches in cross section and total about 20% of the rock by weight. The maximum thickness of gypsum in one minable unit verified by core is 12.5 ft, and its purity is 81.3%. Chloride content of the gypsum beds is less than 0.005%. Depth to the gypsum in La Porte County is 330 to 500 ft, about the same depth as the gypsum being mined in Martin County, Ind. In June 1964 the Indiana Geological Survey discovered gypsum deposits of probable commercial thickness near La Porte, Ind. (Fig. 1). This article presents preliminary data on the distribution, thickness, depth and chemical composition of the gypsum, the possible causes of gypsification, and economic considerations of immediate interest to industry. Because of the preliminary nature of the work, only a few geologic relationships concerning the genesis of the deposits will be mentioned. DEFINITIONS The following terms used throughout this article have been restricted to the following definitions: evaporites: anyydrite (CaSO4) or gypsum (CaSO4 . 2H2O). minable evaporites: any evaporite unit which may contain more than 80% evaporites, which is more than 10 ft thick, and which in places may be completely gypsified. PREVIOUS WORK The presence of gypsum and anhydrite in the Devonian rocks of northern Indiana has been recognized for at least 70 years1-4 and can be inferred from a number of reports on the geology of Michigan. For example, in a cross section from southwestern to central Michigan, Ells5 indicated the presence of

Jan 1, 1965

By A. Andreas

New Mexico retained its position in 1938 as the sixth largest oil-producing state, with a total production of 35,510,176 bbl. This was 2,875,598 bbl. less than the 1937 production of 38,485,774 bbl., or a decrease of 0.077 per cent, which was caused by the lack of pipe-line facilities and storage at the pipe-line terminals. The production for Lea County (excluding Maljamar) was 32,926,788 bbl.; for Eddy County (including Maljamar) was 2,225,411 bbl.; and for northwestern New Mexico (San Juan and McKinley Counties), 357,977 bbl. The average daily nonmarginal well allowable for Lea County on Jan. 1, 1938, was 65 bbl. At the close of the year it was 49 bbl. The average daily pipe-line runs for domestic consumption were less than the state allowables recommended by the United States Bureau of Mines. There was a demand for Artesia crude for foreign export, which if included in the daily production for New Mexico would be slightly in excess of the daily production recommended for New Mexico by the Bureau of Mines. The daily average production for the year was 97,329 barrels. There were 622 completions in the state, of which 520 were oil wells; 16 hydrocarbon gas wells; 5 carbon dioxide gas wells, and 81 dry holes. Of the dry holes 38 were in or near-by proven fields and the remainder, 43, were wildcats. Five new fields were discovered in New Mexico during 1938, three in Lea County and two in Eddy County. Southeastern New Mexico Lea County.—The Monumcnt field was the largest producing field in Lea County, with 9,440,334 bbl., and was closely followed by the Eunice field with 8,872,335 bbl. The Hobbs field was third with 5,010,414 bbl. The greatest activity in Lea County was in the Vacuum pool, with 129 completions, of which 126 were oil wells and three were dry holes. The Texas Company completed its Corbin NO. 1 in the KW 1/4 SW1/4 sec. 10, T. 18 S., R. 33 E. in August. This well was drilled to a depth of 5118 ft. in a white sand, encountering salt water. It was plugged back to 4315 ft, and pumped 43 bbl. of 36" gravity oil in 12 hr. It was approximately 6 miles southwest of the closest production in the Vacuum

Jan 1, 1939

By George Rice

SOME form of longwall mining is generally used in Continental Europe; also in Great Britain where the coal is weak and friable, or the coal bed provides material for pack walls and filling, or where the bottom is soft and squeezes up easily, or the roof is pliable, or the bed is thin and brushing provides building material, or the thick multiple seams are mined in layers, such as the 24-ft. seam at Weymss, Scotland or the 10-yd. pitching bed near Coventry, England. Pillar methods have been retained in British fields where the coal beds are from 5 to 9 ft. (1.5 to 2.7 m.) thick, and free from thick partings or binders or without draw slate, which would provide waste rock for pack walls, or where the roof is hard and requires shooting to bring down and also the bottom or floor is comparatively hard. The room-and-pillar system, by which probably 95 per cent., of the coal of the United States is produced, is now found in only a few mines in Wales, where it is known as the pillar. and .(single) stall method. The American room-and-pillar system is not equivalent to the bord-and-pillar or stoop-and-room system. The essential difference between the bord-and-pillar and the average American room-and-pillar system is probably due to natural conditions. The majority of the coal mines in the United States have a depth of less than 700 ft. (213.m.). The bulk of the coal mined in Europe comes from a depth of more than 1200, ft., while the deepest mines in Great Britain, Belgium, and France reach 3500 to 4000 ft. In deep workings wide spans are impracticable, even with the use of abundant timber; accordingly, as the mines in the United States become deeper the rooms will become narrower and the pillars thicker, and the bulk of the coal will be extracted on the retreat. It is generally conceded, without reference to the cost of production, that the larger the pillars left on the first mining, the more thoroughly can the, coal be extracted. In Europe complete extraction is generally compelled either by the lessors or by the governments; whereas in this

Jan 2, 1921

By Philip Henry

THERE is a difference of opinion among engineers on the subject of depreciation in general, and still more on its application to any given case. The committee which was appointed by the American Society of Civil Engineers to make a report on Valuation of Public Utilities, states "There is no subject connected with valuation about which there are more diverse views than those relating to depreciation;" and in the discussion which took place upon the presentation of the preliminary report of this committee in January, 1914, that part of the report dealing with depreciation called forth more discussion than any other. From this discussion it was evident that the word " depreciation" was not always used in the same sense, so it is quite important that some definition be adopted. As this paper relates to the proper method of treating depreciation by corporations or individuals operating oil properties, both of which must make a return of annual net income to the government in connection with the income tax, it will be in order to adopt the definition of the Internal Revenue Bureau. Under date of Mar. 29, 1910, the Commissioner of Internal Revenue of the Treasury Department stated "Deduction on account of depreciation of property must be based on lifetime of property, its cost, value and use." Again, on Form 1035, "Return of Annual Net Income" for miscellaneous corporations (Section 2, Act of Congress approved Oct. 3, 1913), a deduction from gross income is allowed for "Total amount of depreciation for the year." This item is defined more particularly as follows: "The amount claimed under Item No. 5 (b) for depreciation should be such an amount as measures the loss which the corporation actually sustains during the year in the value of buildings, machinery, and such other property as is subject to depreciation on account of wear and tear, exhaustion, or obsolescence. The amount taken credit for on this account in order to be allowable should be so entered on the books as to constitute a liability against the assets of the corporation. The amount claimed under this item should not cover losses in the value of stocks and bonds. Decrease in the book value of securities owned, so far as such decrease represents a decline in the actual value of such securities, should be deducted under item 5 (a) of the return.

Jan 1, 1915

By Thomas H. Clagett

ThE Pocahontas coal field comprises the area in Tazewell County, Va. and Mcrcer and McDowell counties, W. Va., in which Nos. 3 and 4, Pocahontas seams of bituminous coal are mined. It is a mountainous region with ridges rising 300 to 1000 ft. (91 to 305 111.) above the very narrow valleys and, except for some poorly kept farms along the tops of the ridges and the area occupied by the mining and coking plants and villages, is wooded throughout. First shipments were made from Pocahontas in 1883. There are now about 100 mines, 95 per cent. of which are drift mines. At the end of 1920, approximately 298,000,000 gross tons of coal had been produced and 35,000 acres of coal mined. No. 3 seam is from 4 to 10 ft. (1.2 to 3 m.) thick, but the change is gradual and the thickness fairly uniform in any particular locality. It has a streak of bone, about 2 in. (5 cm.) thick, to which the coal adheres on both sides. In parts of the field this bone is replaced by hard slate, usually from 2 to 4 in. thick. The seam has a slate or fireclay bottom and a draw-slate top. No. 4 seam is from 65 to 80 ft. (19.8 to 24 m.) above No. 3 seam, and of minable section only in the western part of the field. It is from 3 to 8 ft. thick and has two streaks of bone, cach from 1 to 2 in. thick. It has a fireclay or slate bottom and is overlaid by from 4 to 24 in. of a laminated coal and slate, locally termed "black rash," which is separated from the coal seam by about 3 in. of slate. This "black rash" averages about 2.5 per cent. ash, but contains some clean coal. The coal in both seams is quite soft. Cleavage sufficieiltly well defined to exert an influence on the mining is rare. Overlying strata arc slates, shales, and sandstones, the sandstones predominating, extending from 30 to 1000 ft. above No. 3 seam. The strata directly above the draw slate of No. 3 seam, or "black rash" of No. 4 seam, and up to the first sandstone are usually slates or shales, about 10 ft. thick over the.

Jan 1, 1923

By R. Kossowsky

BRIDGMAN has listed five possible transitions in bismuth at 25°C which were observed as volume changes. He was unable however to detect the last three transitions by electrical-resistivity changes. Kennedy and LaMori have verified the pressures at the Bi 1-11 and Bi 11-111 transitions. They suggested however that the 125-kbar transition previously reported by Bundy3 actually corresponds to the 90,000 kg per sq cm transition observed by Bridgman.1 Jura4 reported a well-defined drop in resistivity at 92 kbar obtained by a four-lead method. The Bi 111-IV and Bi IV-V transitions have not been reported in any of the above-mentioned references.'-' Bundy3 observed a small dent in the low-temperature boundary of the Bi Vll region which is consistent with the presence of a 111-IV boundary. Zeitlin and Bray-man5 were the only ones to report small but well-defined drops in resistance of bismuth at 44.0 and 63.8 kbar, corresponding to Bridgman's 111-IV and IV-V transitions, respectively. High-purity (99.99 pct) 0.020-in.-diam 0.5-in.-long bismuth wire was used to calibrate the Uniram tetra-hedral high-pressure apparatus used in the present work. The bismuth phase changes at 25°C were correlated with changes in electrical resistance as a function of pressure. The output of a sensitive bridge constructed of carbon resistors and kept at a constant temperature of ±°C during the measurements was fed to the Y axis of a MoseleyX-Y recorder and the X axis was used for time scans. Specimens were pressurized using a hydraulic press with maximum capacity of 200,000 lb. Load was applied in increments of 2000 lb and held for about 3 min. The resistance was recorded at the end of this time period. Good contact was established below 20,000 lb. Typical recorder charts are reproduced in Figs. 1 and 2 which show that resistance fluctuations were practically nil during each time scan. Well-defined discontinuities in resistance were observed at 58,000 and 82,000 lb, Fig. 1. Two small but definite "blips" are noticed at 92,000 and 122,000 lb, Fig. 2. At 156,000 lb another drop is observed which

Jan 1, 1967

By Thomas H. Clagett

ThE Pocahontas coal field comprises the area in Tazewell County, Va. and Mcrcer and McDowell counties, W. Va., in which Nos. 3 and 4, Pocahontas seams of bituminous coal are mined. It is a mountainous region with ridges rising 300 to 1000 ft. (91 to 305 111.) above the very narrow valleys and, except for some poorly kept farms along the tops of the ridges and the area occupied by the mining and coking plants and villages, is wooded throughout. First shipments were made from Pocahontas in 1883. There are now about 100 mines, 95 per cent. of which are drift mines. At the end of 1920, approximately 298,000,000 gross tons of coal had been produced and 35,000 acres of coal mined. No. 3 seam is from 4 to 10 ft. (1.2 to 3 m.) thick, but the change is gradual and the thickness fairly uniform in any particular locality. It has a streak of bone, about 2 in. (5 cm.) thick, to which the coal adheres on both sides. In parts of the field this bone is replaced by hard slate, usually from 2 to 4 in. thick. The seam has a slate or fireclay bottom and a draw-slate top. No. 4 seam is from 65 to 80 ft. (19.8 to 24 m.) above No. 3 seam, and of minable section only in the western part of the field. It is from 3 to 8 ft. thick and has two streaks of bone, cach from 1 to 2 in. thick. It has a fireclay or slate bottom and is overlaid by from 4 to 24 in. of a laminated coal and slate, locally termed "black rash," which is separated from the coal seam by about 3 in. of slate. This "black rash" averages about 2.5 per cent. ash, but contains some clean coal. The coal in both seams is quite soft. Cleavage sufficieiltly well defined to exert an influence on the mining is rare. Overlying strata arc slates, shales, and sandstones, the sandstones predominating, extending from 30 to 1000 ft. above No. 3 seam. The strata directly above the draw slate of No. 3 seam, or "black rash" of No. 4 seam, and up to the first sandstone are usually slates or shales, about 10 ft. thick over the.

Jan 1, 1923

By R. P. Carreker

ONE of a series, this report is concerned with the experimental documentation of the deformation behavior of pure metals over a wide range of temperature. Previous reports in the series describe the creep behavior of platinum1 and aluminum2 and the tensile behavior of copper,&apos; silver,& and molybdenum.5 Subsequent reports will describe the creep behavior of copper and silver and the tensile behavior of platinum, thus providing extensive creep and tensile data on four face-centered-cubic metals tested under comparable conditions. Material Two lots of high-purity aluminum were used in this investigation. One lot, designated AC, was obtained direct from the Aluminum Co. of America as high-purity aluminum in notch-bar form. A typical analysis of this type of aluminum is 0.006 pct Si, 0.015 pct Cu, 0.006 pct Fe, and 99.975 pct Al. Lot BS was obtained from J. I. Hoffman of the Bureau of Standards as a portion of the Aluminum A described in his report of the redetermination of the atomic weight of aluminum.6 Lot BS originated with the Aluminum Co. of America also, and was received in the standard notch-bar form. A detailed chemical and spectroscopic analysis of lot BS has been published.6 Principa1 impurities were 0.006 pct Si, 0.003 pct Fe, 0.002 pct Cu, and >99.987 pct Al. Samples were processed identically by room-temperature swaging and drawing to 0.030 in. diam wires from approximately ½ in. diam rods that were machined from the notch-bar pigs. Samples were cut from the cold-drawn wire, placed in a grooved graphite block in groups of thirteen, and annealed in air for 1 hr at each of several temperatures, with the results shown in Table I. The two lots of aluminum responded quite differently to annealing, the behavior of aluminum AC suggesting that its grain growth was controlled by impurities. The recrystallization texture of aluminum of similar purity comparably treated has been reported as predominantly <111> fiber with some <100> fiber present.7 Testing Procedure The testing procedure and method of analyzing the data have been described previously.2,3 Annealed specimens of 5 in. gage length were tested in an Instron tensile testing machine at a constant head motion corresponding to a strain rate of 0.04 min-&apos; at a number of temperatures. Instantaneous tenfold rate changes were employed in some tests to deter-

Jan 1, 1958