Search Documents

By Donald W. Scott

Generally speaking, there is nothing very difficult about taking good microgrztphs of photogenic thin sections or grains with a petrographic microscope-camera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. Ia) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. Ib) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this' is an incorrect interpretation is evident by reexamining the micrograph of Fig. Ia. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. Ic the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1949

By L. G. Graper, E. L. Ramsey

THE present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semi-killed as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. ADDING SULPHUR AS A SULPHITE These difficulties can be avoided if sulphur is introduced into the steel by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which-upon decomposition-forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig, I shows photomicrographs of steels made with sulphur, while Fig, 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast-that is, before rolling and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions are more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. RESULTS As stated before, the sulphur dioxide is added to steel by means of the decompcsi-

Jan 1, 1942

By H. G. Dwyer

CONSIDERATION for future expansion influenced the design of the new smelter at Chuquicamata. The section of the smelter now going into operation, while large, represents only little more than half of the ultimate plant. Equipment for the direct smelting of raw concentrates has been arranged in the conventional manner although needless details have been eliminated wherever possible while mechanical and electrical features not usually found in copper smelters have been incorporated. Access is afforded to all equipment but platforms and walkways have been held to a minimum. The poling and other platforms in the converter aisle, normally subjected to battering by ladles and other heavy equipment in transit, are of concrete construction with steel grid armor embedded in the exposed surfaces. Noticeably absent are the many platforms formerly required for the handling of converter flux since this material is charged to the converters through the side walls of the converter uptake hoods. Clear space with ample headroom is provided under each converter and converter puncher's platform to permit clean-up by small bulldozers. Remote controls have been introduced at many points. Electrical control rooms and control centers have been conveniently located. An electrical tunnel with cross tunnels and escapeways is situated under the entire length of the converter aisle for power feed lines. Skull breaking facilities are in a separate building near the smelter. A silica-slurry building with brick storage area is adjacent to the smelter building so that elevator service is available to both buildings. A smelter office, a change house and lunchroom are provided in convenient locations. Units of the smelter as presently constructed are shown in the plan and table on page 1194. The ultimate smelter will house 7 reverberatory furnaces, 14 waste-heat boilers, 9 Peirce Smith converters, 4 casting furnaces serving 2 casting wheels, and one holding furnace serving a straightline casting machine. Additional crane requirements in the converter aisle will necessitate the installation of special hoisting equipment in space already provided in a raised section of the roof over the casting end of the aisle. Thus a complete crane may be lifted high enough above the crane rails to permit the passing of another crane underneath thereby giving all cranes full use of repair facilities already installed. For the collection of gases, 2 dust chambers, each with separate stacks, will collect converter gases and 2 balloon flues with separate stacks will collect reverberatory furnace gases. Extensions necessary to complete the ultimate plant will be possible with little interruption to normal operations since the future converters and reverberatory furnaces will be added at the east end while additional casting facilities will be added at the west end of the present plant. The future units may be added singly or all at one time depending on requirements.

Jan 1, 1952

DETAILED programs for the Regional Meeting to be held at Boston, on Aug. 29, 30, 31, will be available on arrival at the Copley-Plaza Hotel, where registration will begin at 10 a. m. on Wednesday morning. The opening session will be non-technical in character and will be called to order at 11 a. m. Hector J. Hughes, Dean of the Graduate School of Engineering of Harvard University, and others will speak, and in the afternoon visits are to be made both to Harvard and Massachusetts Institute of Technology. Wednesday afternoon will be devoted mainly to the opening of an exhibit of geophysical instruments and methods at Tech. On the way back to the hotel a tour of Old Boston will permit the visitors to see many of the historic points of the city. A special meeting of the Board of Directors has been called to be preceded by the usual subscription dinner at the University Club at 6.30 p. m. Owing to limita-tions of room, invitations have been sent only to the usual list designated in the By-Laws, the Directors, past officers, chairmen of sections and of technical committees. The dinner and a brief business session of the Board will be followed by a technical session at the Copley-Plaza at 8 p. m. and this in turn by a buffet supper at the University Club at 10 p. m. Sep-arate entertainment is being provided for the women for the evening. Thursday will be devoted to technical sessions both in the morning and afternoon. If necessary to permit adequate discussion, an overflow session will be ar-ranged in the afternoon. In the evening, a subscription dinner will be given at the Copley-Plaza at which past-presidents John Hays Hammond and Robert H. Rich-ards will be guests of honor. It is promised that speeches will be short and dancing will be arranged for following. The women will be offered a luncheon and bridge party at one of the country clubs on Thursday, and Friday will be devoted to an all-day excursion for both men and, women. Members are asked to register promptly on arrival so that the various committees will know as early as possible for how many to provide. The major part of the technical program has been provided by the Committee on Geophysical Methods of Prospecting, and a series of papers of great value and interest in this new field has been brought together. Abstracts of substantially all of them are printed in this issue of MINING AND METALLURGY and the papers themselves will, with one or two exceptions, be avail-able in printed form at the meeting and later in the regular publications of the Institute.

Jan 9, 1928

By M. Muskat, H. H. Evinger

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942

By James Pollock

The possibility of colloidal deposition of cinnabar has been neglected. In opalite deposits cinnabar exists in particles within or near the colloidal size range. Colloidal processes have been admitted to be operative in hot springs and low-temperature deposits similar to most cinnabar deposits. Mercuric sulphide sols are stable to elevated temperature and pressure, and in nature probably are chiefly affected by the electrolytes in solution, dilution of colloid, and presence of protective colloids as silica. The stability of mercuric sulphide sols to electrolyte is measured, and shown to be greatly increased by dilution and by the protective action of silica. Mercuric sulphide sols follow the Schulze-Hardy valency rule, therefore the precipitating power of complex mixtures of electrolytes can be computed roughly. The stability of mercuric sulphide sols is shown to be greater than the equivalent precipitating power of the electrolytes in a hot spring depositing mercuric sulphide. It is concluded that finely divided or earthy types of cinnabar are colloidally deposited. Possibility of Collodial Deposition While colloidal solution has been suggested as a means of transport for a number of minerals, such as the sulphides of antimony, arsenic, and iron, it has been neglected in connection with mercury. This is surprising because there exists positive evidence that cinnabar is present in certain deposits in particles of colloidal or near colloidal size. Colloidal transport could result from either the rapid dilution or neutralization of alkaline sulphide solution bearing mercury coming in contact with deep ground waters, or from colloidal solution near the original source and subsequent flow to the point of deposition unchanged. That the dilution of a mercuric alkaline sulphide solution will precipitate mercury sulphide in colloidal form has been demonstrated a number of times and is easily confirmed. The dilution hydrolyzes the alkaline sulphide Na2S to the corresponding hydroxide and hydrosulphide NaOH and NaHS, and the diminution of the concentration of alkaline sulphide reduces the solubility. It is not the contention of this writer that colloidal deposition is the mode of transport of mercuric sulphide in all mercury deposits, but that the stability of a mercuric sulphide sol, as demonstrated below, in waters that are similar to those that have deposited mercuric sulphide necessitates consideration of this possibility in many deposits, especially those of the hot-spring and so-called opalite type. Evidence of Colloidal Deposition Ross1 has shown that most deposits of quicksilver are formed at low temperatures and pressures, and probably by solutions that have relatively simple chemical compositions. In most cases the solutions are probably similar to those observed in hot springs, and in two instances—at Steamboat Springs, Nevada, and Sulphur Bank, California—hot springs have been reported by Becker as actually depositing cinnabar.2 Opalite deposits were believed by early investigators to be surface phenomena

Jan 1, 1949

By Floyd C. Kelly

A. HUltgren, .Söderfors, Sweden (written discussion*).—From the results obtained in his own experiments as well as those of Austin and of Grube Mr. Kelley derives a general law, expressed tentatively in the following words: "whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, a comparatively rapid, or abnormal, grain growth results." It is suggested that,, in order adequately to represent the facts, this definition should he restricted by the following qualifications: a and b are the two metals, b diffusing into a. A. At the temperature in question a should exist as phase a 1 having a limited solubility for b. B. The supply of b by diffusion should be sufficient, in view of the rate of diffusion into a 1, to increase the concentration of b above the saturation value in a 1 so as to cause a new phase a2 to form. (7. The phase a2 should have a range of solubility for 6, thus rendering continued diffusion possible. D. In order that the columnar grains may be preserved in the structure the phase a2 should, of course, not suffer transformation on cooling. The phenomenon thus defined may be described as progressive transformation by diffusion. Its mechanism would appear to he as follows: Fig. 17 shows a portion of the equilibrium diagram a-b, Fig. 18 the distribution of b in solution after various periods of diffusion, Fig. 19 represents the structure in cross-section of a cylindrical rod of a at the end of heating period 3. 1. The first effect of diffusion of b into a will be to establish a concentration gradient in phase a1 (1, Fig. 18). When the saturation value for the temperature of the experiment (m, Fig. 17) is reached at the surface, nuclei of, a2 of composition n will form here, and later develop into a continuous layer. Assuming that diffusion proceeds without irregularities and that transformation at any point sets in without lag—i. e., in the moment saturation is exceeded—the transformation a1-a2 will advance inwards on a cylindrical surface concentric with the surface of the rod. The discontinuity of composition at the transformation surface in the position it happens to have at the end of the treatment (3, Fig. 18) will be preserved at room temperature, if the cooling is not particularly slow, and be recorded in the structure as a marked, smooth line, in agreement with Grube's and the author's observations. The shape of the distribution curves in Fig. 18 is also corroborated by the analyses given by Grube. 2. During diffusion, since the secondary phase a2 is always in immediate contact with the saturated part of the primary phase a1, there should be very little lag in the transformation. This means that the first a2 grains formed should grow in preference to the formation of independent nuclei; in other words, columnar growth results. It does not seem necessary to assume, with Green,' whose conception of the phenomenon

Jan 1, 1929

By H. Foster Bain

THIS subject is one that has attracted my attention for a good many years. All of us have had occa-sion to think of the waste that comes from the poor organization of our methods of finding mines and of looking after prospects. Probably all of us, in, examination work, have made a long and difficult journey to see some prospect, in a far country, or often in the mountains, have found the prospect one that never could be developed, and have learned for the first time that it had been previously examined by from two to six of our professional associates, who, each in turn, condemned the property as worthless. I know properties, as all of you do, that have been repeatedly examined by first-class engineers. Perhaps it would not be safe or wise to have an invariable rule that, each prospect should be entitled to only one examination by one engineer; and yet, it seems to me that somewhere there is a middle ground to take; it is hardly necessary that each little prospect should be examined so many times that the walls get greasy from the climbing of mining engineers, or the stopes get filled up with cigarette stumps. 'This mining engineering profession ought to have brains enough to find some way of making this unnecessary, and of making the benefit of an examination, in some cases at least, and in a much larger number of cases than at present, avail-able to the industry as a whole. If we would save the amount of money that is spent unnecessarily on reexamination of properties, and let that money flow into the actual development of )properties, I believe that, in the long run, we would be better off. Just how to do that is another problem. In 1916, while in London, Edgar Rickard and I attempted to do something of that kind. We started to organize a plan whereby mining engineers might, with the consent of their class, turn over to a central organization their reports on properties they had examined, whereby men who had occasion to look up these same properties might, on payment of a fee (which should go back to the original client, if you desire, or might be devoted to some other purpose for the benefit of the industry), have access to these earlier reports. We found, in the short time we considered this matter, that a good many British engineers, and a good many of the companies, were willing to consider this. In other words, they were willing to pool their information, as a matter of practical experience. We all know the enormous value of pooling information. I think it is a problem that may well be considered from the point of view of the industry as a whole, which the Society might attempt' to work out on a businesslike basis. Assuming, however, that it is possible to work out a plan whereby we get the minimum number of examina-tions that are necessary and we make some saving in money, we reach another stage-the problem of the examination itself.

Jan 3, 1922

By J. L. Wyatt

J. W. Tomlison—It seems probable that the author's conclusion, that the conductivity of the slags decreases with increasing content of FeO, is erroneous due to the method of plotting the data. Thus, the results of other workers2,3,13,14 show that the conductivity of molten oxide slags increase with increasing temperature, indicating that the trend of the curve shown by the authors is due to the fact that the data for the slags containing relatively small amounts of FeO are at higher temperatures than those for the slags containing relatively large amounts of this oxide. In this connection the work of Wejnarth2 may be mentioned in which in an investigation of a series of iron silicate slags, the conductivity was found to increase with increasing content of FeO; the fact that the author's slags contained TiO2 probably does not affect the issue since it has been shown15,16 that, at least as far as conductivity is concerned, this oxide behaves essentially the same as silica and that mixtures of the oxide with silica have a very low conductivity of the order of 10-4 mhos at 1750°C. In connection with the experimental technique it may be noted that bubbles of carbon monoxide would probably be produced at the surface of the graphite electrodes in contact with the melts thus rendering the accuracy of the measurements somewhat open to question. J. L. Wyatt (author's reply)—Dr. Tomlinson makes reference to works by Martin and Derge, which indicate that slag systems containing no TiO2 are charac-terized by an increase in conductivity with an increase in temperature. Further, I have cited his examples, which indicate a drastic increase with small temperature change. The results of Dr. Derge's work have no bearing whatsoever on the results of this paper, since the slags under study here contained up to 70 pct TiO2. One cannot generalize on slag systems as a whole on the basis of any one family, for there are definite compounds of ionic nature formed in each system, and the ionic mobilization of these is something that cannot be determined without actual experimentation. Dr. Tomlinson makes reference to an unpublished work which, he claims, shows that titanium dioxide behaves the same as silica in regard to conductivity. Since I have not had 'an opportunity to see the paper I cannot make any comments, but unless the same slag system was studied there can be no specific comparison of results. If the decrease in conductivity of the slag was due entirely to temperature phenomena, as Dr. Tomlinson indicates, then one is without an explanation of the values shown in the paper for slags containing from 10 to 20 pct FeO. I cannot agree that the deviation in findings was appreciably related to temperature change; further, I believe this point was completely covered in the paper. References 13 Endell and Hellbrügge: Glasstech. Ber. (1942) 20, 277. 14 Bockris, Kitchener, Ignatowicz and Tomlinson: Faraday Society. Discussion (1948) 4, 265. 15 Tomlinson: Thesis, London 1949. 10 Bockris, Kitchener, Ignatowicz, and Tomlinson: Unpublished work.

Jan 1, 1951

By Floyd C. Kelly

A. HUltgren, .Söderfors, Sweden (written discussion*).—From the results obtained in his own experiments as well as those of Austin and of Grube Mr. Kelley derives a general law, expressed tentatively in the following words: "whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, a comparatively rapid, or abnormal, grain growth results." It is suggested that,, in order adequately to represent the facts, this definition should he restricted by the following qualifications: a and b are the two metals, b diffusing into a. A. At the temperature in question a should exist as phase a 1 having a limited solubility for b. B. The supply of b by diffusion should be sufficient, in view of the rate of diffusion into a 1, to increase the concentration of b above the saturation value in a 1 so as to cause a new phase a2 to form. (7. The phase a2 should have a range of solubility for 6, thus rendering continued diffusion possible. D. In order that the columnar grains may be preserved in the structure the phase a2 should, of course, not suffer transformation on cooling. The phenomenon thus defined may be described as progressive transformation by diffusion. Its mechanism would appear to he as follows: Fig. 17 shows a portion of the equilibrium diagram a-b, Fig. 18 the distribution of b in solution after various periods of diffusion, Fig. 19 represents the structure in cross-section of a cylindrical rod of a at the end of heating period 3. 1. The first effect of diffusion of b into a will be to establish a concentration gradient in phase a1 (1, Fig. 18). When the saturation value for the temperature of the experiment (m, Fig. 17) is reached at the surface, nuclei of, a2 of composition n will form here, and later develop into a continuous layer. Assuming that diffusion proceeds without irregularities and that transformation at any point sets in without lag—i. e., in the moment saturation is exceeded—the transformation a1-a2 will advance inwards on a cylindrical surface concentric with the surface of the rod. The discontinuity of composition at the transformation surface in the position it happens to have at the end of the treatment (3, Fig. 18) will be preserved at room temperature, if the cooling is not particularly slow, and be recorded in the structure as a marked, smooth line, in agreement with Grube's and the author's observations. The shape of the distribution curves in Fig. 18 is also corroborated by the analyses given by Grube. 2. During diffusion, since the secondary phase a2 is always in immediate contact with the saturated part of the primary phase a1, there should be very little lag in the transformation. This means that the first a2 grains formed should grow in preference to the formation of independent nuclei; in other words, columnar growth results. It does not seem necessary to assume, with Green,' whose conception of the phenomenon

Jan 1, 1929

By W. A. Griffith

The fundamental principles and modern techniques of experimental planning and data analysis, applicable to any type of research, are particularly important in flotation experimentation. Since they constitute the modern science of experimentation, they should be among the working tools of any scientist, research engineer, or plant operator engaged in flotation investigates. This chapter is a review of these principles and techniques. Equipment and procedures for the actual conduct of experiments will not be discussed here since these subjects are well covered elsewhere in this volume. Neither will any attempt be made to impart a working knowledge of statistical methods of data analysis since this would be impossible in the space allotted, and many excellent texts are available to the diligent inestigator.1-4 The objective here is simply to interest the reader in the application of statistical techniques to flotation experimentation by illustrating their utility in situations frequently encountered, and to point out the principles of experimental planning necessary for their proper use. Any conscientious metallurgist engaged in flotation experimentation or operations is well aware of the inherent complexity of the flotation process, and of the often frustrating difficulties this introduces into experimentation. The raw materials normally treated by the process are complex both physi- cally and chemically, and often highly variable even when from the same source. The flotation process itself is characterized by a very large number of potentially important process variables. Many of these are beyond the con- trol of the metallurgist, and some cannot even be measured quantitatively with available instruments. Those which can be measured and controlled with reasonable precision often produce effects which are intricately interrelated. Not only are the variables many, but the physical and chemical mechanisms by which they function are imperfectly under stood. To compound the difficulty, experimental techniques are relatively crude. Controls are not very precise, and the human factor looms large in most flotation experiments. These situations lead inevitably to experimental data of a relatively low degree of precision or reproducibility. Some are inclined to think that these conditions are unique to flotation experimentation. They are not. The experimental problems met by the agronomist, the biologist, the social scientist, and others are equally complex. Investigators in these fields pioneered in the development of methods for handling just such situations by proper experimental planning and the application of statistical methods in the analysis of data. Their pioneering work has grown into a well established modern science of experimentation which has spread into every field of science. This science is based upon statistical

Jan 1, 1962

By George T. Bator

If confronted with the problem of pumping a mixture of slime-free sand, gravel and boulders up to six in. in diameter, at the rate of 175 tons per hr in one single-stage pump against a static head of 90 ft and a total head of 140 ft, of which 20 is on the suction side, an engineer might be forgiven for backing away from the job, especially if he were also told that the pump wearing parts must have a minimum hardness of 550 Brinell for the sake of abrasion resistance.

Jan 1, 1950

By N. A. D. Parlee, N. M. El Tayeb

Fe-V alloys with small percentages of vanadium show no deviations from Sieverts' Law up to P~, = 1 atm in the 1600º to 1750ºC region. At somewhat under 8 pct V and up to at least 20pct V, at 1604" and 1661 °C, nitrogen absorption follows Sieverts' Law at low Pn2 values, but deviates from this law beyond critical values of pn2, due to formation of a nitrzde phase of approximately VN composition. The behavior below these solubility limits can be described at all temperatures by the equations: RAO and parlee1 suggested that the nitrogen absorption curve for liquid iron alloys takes the general form shown in Fig. 1 when an alloy nitride precipitate is formed. They showed that the precipitation of 6 titanium nitride from liquid Fe-Ti alloys follows this general scheme and dealt with the general theory involved. Recently, Evans and Pehlke2 reported their research on the precipitation of aluminum nitride from liquid Fe-A1 alloys. Fountain and Chipman's recent paper3 on the precipitation of boron nitride from solid solution contains a fine example of the analogous behavior which they have been studying in the solid state. Researches on the absorption of nitrogen by liquid Fe-V alloys have been described by various authors.1,4-7 Most of this work has been confined to fairly low vanadium concentrations and rather high temperatures because of difficulties variously described as, formation of surface scums, bridging, and so forth. This behavior and the rough thermo- dynamic calculations made by chipman,8 over eleven years ago, indicated that excessively high vanadium concentrations should not be required for vanadium nitride precipitation. It seemed desirable to look for and study this precipitation in order to fill out the thermodynamically interesting nitrogen absorption data on these alloys. EXPERIMENTAL METHOD The general method used was essentially the same as employed by Rao and parlee,1 in which a Sieverts type of apparatus was used and the precipitation of the nitride detected by the "break-point" in the Sieverts' Law line, and by the visual observation of the formation of the new phase on the surface of the melt. There were, however, a few differences in apparatus and technique as described below. The oil manometer used by Rao and parlee' to measure low partial pressures of nitrogen was not employed. The present authors sought to avoid as much as possible the exposure of the liquid alloy to low total pressures of gas during the 6 to 10 hr long runs because of the heavy iron evaporation-loss errors involved. This was achieved, partly by keeping evacuation times to a minimum with fast pumping but largely by the use of two burettes, one for argon and one for nitrogen, and using them to equilibrate the alloy with mixtures of argon and nitrogen rather than nitrogen alone. Each run involved a careful sequence of operations. After melting, de-

Jan 1, 1963

By W. D. Steele, S. D. Brady

THE Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains mineable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon¬galia Co. thence south and southwest across the state to Wayne Co. near Huntington. The Pittsburgh coal is also mineable in the Upper Potomac region but is now practically exhausted there. The total mineable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13% billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio river as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern. West Virginia District comprising Wetzel, Monongalia, Marion, Preston, Harrison, Doddridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 188o (when the Monongahela River Railroad, now B. & O. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgantown and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Monongahela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of mineable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. ECONOMIC IMPORTANCE The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1948

By James J. Wise

INTRODUCTION One basic design feature utilized in all caving and sublevel stoping techniques is the drawpoint. These draw- points may be located on sublevels when using sublevel caving methods, or may be located at the floor pillar when using block caving, sublevel stoping, or vertical crater retreat methods. How the drawpoint is designed and developed, how the ore is withdrawn from it, and how the ore is hauled to the shaft or portal encompasses the loading and hauling function. Historically, predominate loading and hauling equipment for caving and sublevel stoping has been scraper slushes, air powered overshot loaders, and rail mounted train haulage. All of this equipment has two common constraints. 1. The equipment locked into specific work sites and is not easily shifted to another work site. This constraint can often lead to low utilization and low productivity of the equipment. 2. The equipment is designed to work in the horizontal plane, which requires that the various horizontally-oriented working levels be connected by vertical raises. Vertical development by means of raises is not only increasingly expensive, but also is not well adapted to movement of large equipment into the s topes. In the last 20 years, two revolutionary labor saving concepts have become common in caving and sublevel stoping. 1. Long-hole drilling, which has mechanized the development of the drawpoint extraction structures as well as the actual stoping and undercutting. 2. Vertical access by means of trackless ramps between levels, and the consequent use of rubber-tired vehicles not only for loading and hauling ore, but also for the rapid movement of men, material, and equipment into the stopes. The introduction of trackless mining systems for loading and hauling has not been easy. Mine planners have had to re-orient their thinking to the larger operating space required by trackless equipment. Larger access drifts have necessitated reconsideration of mine layouts to insure proper ground support. Spiral ramp developments were often laid out on slopes steeper than the equipment could negotiate economically. Mine operators had to accept the added responsibility of roadway maintenance, water removal, increased ventilation, and more technical mechanical maintenance. As the mine operators enthusiastically embraced the superior productivity of trackless mining systems, they some- times disregarded opportunities to combine the older types of equipment with trackless vehicles to maximize productivity at lowest cost. In order to gain a proper perspective on this problem, it is necessary to review the various techniques of loading and hauling and to become more aware of the advantages or disadvantages that each system or combination contributes. LOADING Loading consists of two functions, (1) primary loading from a drawpoint and (2) secondary loading into long- haul system, a truck, train, or possibly a belt conveyor. Mine planners have four basic loading systems available to fit various operating conditions. These are, (1) gravity, (2) scrapers, (3) rail-mounted loaders, and (4) trackless loaders. Each system can produce optimum results under specific conditions. Gravity Loading Gravity loading is probably the oldest system in general use today.

Jan 1, 1981

By G. W. Healy, J. C. Schottmiller

Molten silicates were found to exist in the Cr-Si-0 system at temperatures above 1450°C. one atom of oxygen is readily removed from CrzOs in the presence of Si02 at 1700°C, forming a silicate melt. Steam-hydrogen ratio measurements made at this temperature indicate that the free energy of the reaction: Cr20s(c) + Hz = 2CrO (in Si02 -saturated melt) + H20 is approximately 5600 * 1500 cal. A deep-blue chromous silicate, probably Cr2Si04, forms from these melts at about 1400" to 1500°C, and is characterized by.its distinctive X-ray diffraction pattern and optical properties—distinct pleochroism and high refractive indices. THE question of the state of oxidation of chromium in slags has vexed metallurgists for many years The experiments of Koerber and Oelsenl suggested the probable presence of divalent chromium in silica-saturated slags equilibrated with high-chromium melts. Hilty and coworkers2 had also found chromium at lower valency, as Cr304, in inclusions formed from oxygen-saturated Fe-Cr melts with as little as 10 pct Cr. In both cases, disproportiona-tion of the lower oxide to CraO3 and chromium was found to occur to a greater or lesser extent, depending upon the rate of cooling from the high temperature. The work on Cr304 was sufficiently detailed for chipmans to derive its thermodynamic properties, but Oelsen's experiments in the silicate system were not extensive enough since most of his runs were made with slags containing large amounts of manganese oxide in addition to iron and chrome oxide and silica. The present study describes experiments carried out to map out an approximate liquidus diagram in the CrzOs, "CrO", SiOa portion of the Cr-Si-0 system, and to measure the partial free energy of solution of oxygen in the system. EXPERIMENTAL 1) Approximate Melting-Point Determinations. Preliminary trials showed that when an equimolar mixture of Cr20s and SiOa was treated with hydrogen in the temperature range 1500" to 1600°C, copious amounts of steam were evolved, and a low-melting liquid formed which could be quenched to a blue, crystalline, material having a distinctive X-ray diffraction pattern. It was found that the identical material could be produced by heating intimately mixed, finely divided Cra03, Cr, and SiOa, held in a tungsten crucible, under purified argon. Thus, it was possible to prepare mixtures containing any desired proportions of chromium, silicon, and oxygen, pel-letize them, heat to temperature in the furnace shown in Fig. 1, and observe, after cooling, whether the pellet remained unchanged or showed signs of incipient, partial, or complete melting. 2) Free Energy of Solution of Oxygen. This was studied by measurement of steam-hydrogen ratios for the reaction: H20 (gas) + O (dissolved in charge) + Ha (gas) The experimental method chosen was to prepare a

Jan 1, 1964

By E. W. Hough, G. L. Stegemeier

Empirical equations for surface tension of propane and normal butane as functions of reduced temperature are obtained from experimental data. Another correlation relating surface tension to enthalpy of vaporization is given for these two compounds. In addition, new paracbor numbers are calculated for the normal paraffin hydrocarbons. These numbers are utilized for the calculation of interfacial tension of two-component systems as functions of pressure and temperature, using a modified form of Weinaug-Katz equation. The experimental data for two binary systems are approximated by the correlation. From these results it is found that the interfacial tension in the high-pressure region remains extremely low at large pressure decrements below the critical pressure. Thus, it appears that condensate systems may have flow characteristics almost like single-phase conditions even though the pressure is within the two-phase region. Experimental data have shown that interfacial tension divided by density difference approaches zero as the critical pressure is approached. A calculation of wetting-phase saturations indicates that the saturation gradient at the two-phase contact becomes increasingly abrupt as the critical pressure is approached. DISCUSSION Prediction of the surface and interfacial tension of the light hydrocarbons and of two-component hydrocarbon mixtures at various temperatures and pressures may be made if other physical properties are known. Extensive experimental work on single-component and binary systemsl is the basis for the correlations outlined in this paper. Interfacial tension is defined as the specific surface-free energy between two phases of unlike fractional composition, while surface tension is defined as the specific surface-free energy between two phase:; of the same fractional composition. The usual definitions relating interfacial tension to a liquid-liquid interface and surface tension to a gas-liquid interface are not clearly defined when the critical region is included, and there is no sharp distinction between a gas and a liquid phase. Interfacial tension is probably the most important single force that makes one-half to one-third of the total oil actually in place in a reservoir rock unrecoverable by conventional gas-drive or waterflood methods. A rough estimate of this figure for the United States is 100 billion bbl. Interfacial tension presently is used by petroleum engineers in the estimation of saturation gradients at the gas-oil contact and at the oil-water contact. The data in this paper should prove useful for estimates of reserves involving gas-oil contacts. Relative permeability undoubtedly is influenced by interfacial tension, for sufficiently small values. These data should be useful in determining how small the values are In addition, these data should eventually add to our fundamental knowledge of surfaces. At the critical point, all surface excesses approach zero and the thickness becomes very large. SINGLE-COMPONENT SYSTEMS It has been observed1 that the following relationships are good approximations to the physical properties of propane and n-butane.

By J. E. Sherborne, P. H. Jones, E. C. Babson

A study of the Chapman zone in the Richfield field, Orange County, California, indicates that the quantity of oil recovered by present methods will be only a small portion of the oil originally in place. Since the volume of residual oil is believed to be of large magnitude, an experimental water-flooding operation has been initiated in order to determine whether water-flooding offers promise as an economical method of recovering some of this residual oil. A single injection well was drilled between old producing wells, and a water-treating plant using alum flocculation and chlorination was designed and built. Water has been injected into the input well for six months at rates in excess of 100 bbl. per day. Production from one of the neighboring wells has increased materially, the oil production having risen from 7 to 30 bbl. and the water From I to 40 bbl. per day. While definite conclusions regarding the economic success of water-flooding in the Chapman zone are not justified at this time, it has been demonstrated that water can be injected into the zone on a sustained basis and that this water will displace appreciable quantities of oil from the sand. Introduction As a result of an investigation of subsurface conditions in the Chapman zone of the Richfield field, it was concluded that ultimate oil recovery from this zone would probably be low and that natural water encroachment was so localized as to be of little importance from a recovery stand- point. Furthermore, it was found that in many portions of the zone the wells were approaching an unprofitable level of production. When these data were presented to the management of the Union Oil Co.; their reaction was that an attempt should be made to develop methods of recovering at least a portion of the large quantity of oil remaining in this zone. After some investigation, it was decided that wafer-flooding offered the most likely means of accomplishing this end, but reservoir conditions in the Chapman zone differ so widely from those encountered in any of the flooding projects described in the literature that it was difficult to evaluate the probability of success. Despite encouraging results from laboratory tests, it was not even certain that water would displace an appreciable volume of oil from the Chapman sand under reservoir conditions. Therefore, it was decided to initiate a small-scale project, for two purposes: first, to determine whether water would displace oil from the Chapmall sand and, second, to obtain information and experience for future operations if water-flooding appeared to be a promising method of secondary recovery. Reservoir Data The Chapman zone is the upper of the two producing zones in the Richfield field, being found at depths from 3000 to 3700 fi.. The productive portion of the zolle consists of a large irregularly shaped sand body, which is more than 400 ft. thick at the top of the structure. As the margin of the field is approached, the sand is replaced

Jan 1, 1945

By Lewis T. Wright

IT is commonly believed by metallurgists that in copper-smelting, the copper in the slags, which is irreducible by continued smelting, is retained in the form of "prills" of matte. I have frequently held well-settled slag in a molten condition for a long period without being able thereby to reduce the copper-content. The slag acted as though it contained a minimum of dissolved or combined copper that could not be settled out by gravity. I have used reagents, but without satisfying myself in what form this copper existed. The same slags, by fine grinding and elutriation, could not be separated into portions containing more or less copper than the average content. By treating copper-slags in an electric furnace an impure button of copper. was produced, but the high temperature and the strong reducing-action of the furnace were influences that suggest an explanation of a result not obtainable with ordinary smelting-temperatures. If all the copper in the slag were in the form of copper-matte, and not existing as a dissolved compound with some of the elements of the slag, then the other metals in the matte, such as gold and silver, should occur in the slag in the same ratio to the copper as to the copper in the accompanying matte. This reasoning led me to study the ratio of metals in the products of smelting, and, apart from the issues discussed in this paper, the research has proved both interesting and illuminative. On the assumption of a similar ratio of metals in matte and slag, if the percentage of copper in the slag accompanying; a matte containing 50 oz. of silver and 1 oz. of gold per ton of copper was 0.3 per cent., or 96 oz. per ton of slag, there should be found 0.15 oz. of silver and 0.003 oz. of gold per ton of slag:; but, in my experience, there is less silver and much

Sep 1, 1909

By R. P. Carreker, J. C. Fisher

Cheep tests are normally constant load tests. Such tests approximate some types of service conditions and therefore are justified from the engineering point of view. Coupled with this consideration is the advantage of simplicity inherent in constant load tests, as contrasted with the comparatively complex requirements of a constant stress test. It is not surprising that the vast majority of creep tests reported are of the constant load type. Despite the enormous amount of accumulated creep test data, plastic flow is by no means completely understood. The widespread use of constant load tests is at least partly responsible for this lack of understanding. Any attempt to analyze deformation must involve the more fundamental quantity stress, rather than load. It is possible to predict constant load behavior from known constant stress data, but the reverse is much more difficult. When a metal specimen elongates, as in a creep test, the cross section decreases, maintaining constant volume. Thus For a constant stress test the force on the specimen must be decreased as the cross section decreases, that is, this force must be inversely proportional to the elongation of the specimen. An-drade has described three methods of obtaining the constant stress condition,l-3 each of which is relatively complex. The most recent proposal,³ suggests a major simplification which maintains the simplicity of the constant load test while approximating quite closely the desirable condition of constant stress. Andrade's device is admittedly more accurate but the method described below has definite advantages Consider a specimen in the form of a "V" supported at its ends. If a weight be applied at the vertex of the angle, the stress in each leg of the "V" If this stress causes an elongation ?1 in each leg of the "V," the angle decreases from a. to a smaller angle a1. The quantity sec — thus decreases with specimen elongation while the quantity 1/A increases. By selecting proper initial conditions it should be possible to hold S/So very nearly constant at unity. The proper initial conditions are realized when a0 is made equal to approximately 90°. Fig 1 compares the ratios of S/S0 for a0 = 85, 90, 95, 100°, with a0 = 0, that is, a straight speci- men, for true strains up to e = 0.10. It may prove convenient to measure X, the movement of the vertex, rather than the true elongation 1. Contour lines of X/lo are also plotted in Fig 1. The method for obtaining constant stress described above is especially suited to the testing of small wires, but may easily be extended to rods of any diameter through the use of a suitable grip which serves as the vertex joining two identical rods forming the legs of the "V." References 1. E. N. da C. Andrade: On the Viscous Flow in Metals, and Allied Phenomena. Proc. Roy. Soc., A, 84, 1, (1910-11). 2. E. N. da C. Andrade and B. Chalmers: The Resistivity of Polycrystalline Wires in Relation to Plastic Deformation, and the Mechanism of Plastic Flow. Proc. Roy. Soc., A, 138, 348, (1932). 3. E. N. da C. Andrade: A New Device for Maintaining Constant Stress in a Rod Undergoing Plastic Extension. Proc. Phys. Soc., 60, (3). 304, (March, 1948).

Jan 1, 1950